CCi TLEC Series Parts list manual

FUNCTIONS & PRFUNCTIONS & PR
FUNCTIONS & PRFUNCTIONS & PR
FUNCTIONS & PROCEDURESOCEDURES
OCEDURESOCEDURES
OCEDURES
TLEC SERIESTLEC SERIES
TLEC SERIESTLEC SERIES
TLEC SERIES
FEATURES
FULL TARE HOLD FUNCTION
NET WEIGHT INDICATOR BUBBLE BALANCE
ZERO INDICATOR LEVELING FEET
NEGATIVE VALUE INDICATOR 1” LCD DISPLAY
AUTOMATIC OFF FUNCTION LOW BATTERY INDICATOR
BUILT-IN RECHARGEABLE BATTERY OPTIONAL PLASTIC SCOOP
AC ADAPTOR INCLUDED FROM 32 OZ. TO 50 LB
CONVERTS TO METRIC SEALABLE
POSITIVE & NEGATIVE OVERLOAD PROTECTION

TLEC
FUNCTIONS
F.1 DEALER CALIBRATION
F.2 DISPLAY/SEGMENT CHECK
F.3 OFF-SET VALUE
F.4 AUTOMATIC “OFF” FUNCTION
The scale must be “OFF” at the onset for performing all functions.
When instructed to PRESS a key, be sure to do so FIRMLY.
When the scale is turned ON, weight automatically reads in “lb”. To convert to metric
measure, press “MODE”.
_________________________________________________________________________
TO ENTER FUNCTION MODE
1) With the scale turned “OFF”, press and hold “MODE”. While holding “MODE” down,
quickly press and release “ON”. Release “MODE”.
2) Display will read “F.1” (if display reads “F.0”, press “MODE” again which will display “F.1”)
3) Select specific functions by pressing “MODE” until proper selection is displayed.
4) To exit, press “ON”.
* after each adjustment, scale must be re-calibrated *
_________________________________________________________________________
F.1 DEALER CALIBRATION
1) Press and hold “MODE” button. While holding “MODE” button, quickly press “ON”
and release both. Display should read “F.1”.
2) Press “MODE” to display current off-set value.
3) Off-set value should be between 5,000 and 15,000. If value is not within this range,
go to step “F.3” below.
4) Press “ZERO” to zero the scale
5) Press “MODE”, “ZERO”, “MODE”, “ZERO”. Display should read “1” while depressing
“MODE” and “2” when “ZERO” is depressed.
6) Display should read “===Þ” opposite the “ZERO” key. If it does not appear, turn
the scale “OFF” and start again at Step 1.
7) Place full capacity weight on scale (except TLEC-3; add 32 oz.) on platform and allow
display to stabilize.
8) Press “HOLD”
9) The scale should “automatically” calibrate and display should read “donE”.
10) The display will show a numerical “count down” which should reflect the weight on the
platform or “0” if calibration weights have been removed.

F.2 DISPLAY/SEGMENT CHECK
1) Press “MODE” and hold. At the same time, quickly press and release “ON”. Release
“MODE”.
2) Display should read “F.1” (if the display reads “F.0”, press “MODE” again, which will display “F.1”).
3) Press “MODE” until display reads “F.2”.
4) Press “HOLD” to enter DISPLAY/SEGMENT CHECK function. Display will illuminate
all segments of the display to check for failure or damage.
5) Return to NORMAL operation by pressing “ON”.
F.3 OFF-SET VALUE
1) Press and hold “MODE”. At the same time, quickly press and release “ON”. Release
“MODE”.
2) Display should read “F.1” (if the display reads “F.0”, press “MODE” again, which will display “F.1”).
3) To get to “F.3”, press “MODE” twice and then press “HOLD”
4) Display will read current value. If the unit is operating properly, this value will be be-
tween 5,000 and 15,000. If the value is not within this range, you must adjust the off-
set potentiometer on the rear PC board. If, upon adjustment, the value remains outside
the proper range, contact CCi Scale Company Inc. for instructions.
5) Return to NORMAL operation by pressing “ON”
F.4 AUTOMATIC SHUT OFF FUNCTION
1) Press and hold “MODE”. At the same time, quickly press and release “ON”. Release
“MODE”.
2) Display should read “F.1” (if the display reads “F.0”, press “MODE” again, which will display “F.1”).
3) To get to “F.4”, press “MODE” three times and then press “HOLD”
4) The display will indicate either:
a) “4 OFF”, which indicates the unit will automatically shut itself off after four (4) min-
utes on non-operation.
b) “0 OFF”, which indicates the unit will remain in the ON until physically turned OFF.
5) To select the mode that is not displayed, press “HOLD” one time. This should change the
display to the next mode. When the display reaches your selection press “ON”. This returns
the scale to normal operation and your choice is implemented during future operations.
TLEC

ERROR CODES
“ERR 1” Overloaded
The scale weighs from 0 to full capacity plus 9 divisions. The display will read “ERR
1” if overloaded.
“ERR 2” Out of zero range
Tare weight can be removed (tared off) by pressing “ZERO”. This range is from 0
to the full capacity plus 2 divisions. If a weight is tared and “ZERO” is pressed, the
display will read “ERR 2”.
“ERR 3” Low battery indicator
When the display reads “ERR 3”, the scale must be connected to the AC adaptor
and plugged into an electrical outlet (110 V) for approximately 8 hours to fully
recharge the battery.
“ERR 4” Dead load out of capacity
When this display appears, the dead load of platform assembly is out of tolerance (no
additional mass on scale). Call your dealer for service.
NOTE: “ERR 1” and “ERR 4” may also indicate the OFF-SET VALUE is out of range.
Refer to F.3 for adjustment instructions.
TLEC