CDA HCC561/1 Reference manual

Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T: 01949 862 012 F: 01949 862 003 E: [email protected] W: www.cda.eu
Passionate about style
Manual for Installation, Use and Maintenance
HCC561/1 Ceramic Hob

Important
The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this
product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect
installation or misuse of the appliance or use in a commercial environment.
This appliance is not designed to be used by people (including children) with reduced physical, sensorial or mental
capacity, or who lack experience or knowledge about it, unless they have had supervision or instructions on how to use
the appliance by someone who is responsible for their safety.
Under no circumstances should any external covers be removed for servicing or maintenance except by suitably qualified
personnel.
Appliance information:
Please enter the details on the appliance rating plate below for reference, to assist CDA Customer Care in the event of a
fault with your appliance and to register your appliance for guarantee purposes.
Appliance Model
Serial Number
CE Declarations of Conformity:
This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including
Electrical safety (LVD) 2006/95/EC and Electromagnetic interference compatibility (EMC) 2004/108/EC. Parts
intended to come into contact with food conform to 89/109/EC.
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC
DIRECTIVE 2002/96/EC.
At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer
providing appliance recycling services.
Disposing of a household appliance separately avoids possible negative consequences for the environment and health. It also
enables the constituent materials to be recovered, saving both energy and resources. As a reminder of the need to dispose of
household appliances separately, the product is marked with a crossed-out wheeled dustbin.
1

Please note:
• Ceramic hobs become hot and remain hot during and immediately after use. Do not touch the hob until it has been
allowed to cool.
• Keep children away from the appliance when in use.
• Never put cooking foil or plastic materials on the ceramic surface when the hob is hot. These materials could melt and
cause damage to the hob.
• Never use the hob top for storage.
• Pan handles should never stand out beyond the edge of the worktop. This will ensure children cannot reach them.
• Do not use pans with rough bases (e.g. cast iron) as these may scratch the hob surface.
• Do not switch on the zones without cookware in place.
• Do not lean over the hob when it is in use.
• Follow the cleaning instructions carefully.
• Ensure the base of the saucepan is clean and dry before placing it on the hob.
• After use, please ensure that the control knobs are in the ‘Off” position.
• This hob (Class 3) has been designed for use only as a cooking appliance. Any other use (e.g. heating rooms) should be
considered incorrect and therefore dangerous.
• The appliance is not intended to be operated by any means of an external timer or separate remote-control system.
Important
• Do not use the hob if the glass surface is cracked or damaged to prevent risk of electric shock. Disconnect it from the
power supply.
2

Using your hob
Zones:
1.
2. Back left 1.2 kW 160 mm
3.
4. Front right 1.2 kW 160 mm
Control panel:
5. Back right zone control
6. Back left zone control
7. Front right zone control
8. Front left zone control
9. Residual heat indicator lights
10. Hob in Use indicator light
Regulating the temperature:
The power level for each zone can be regulated by turning the relevant control knob to select the desired heat level.
The table below offers guidance as to what each switch position is for.
Fig.1
3
5
6
7
9
10
1
23
4
8
Front left 1.7 kW 190 mm
Back right 1.7 kW 190 mm
Switch position Type of cooking
0 Off position
1 Very gentle
2 Gentle
3 Slow
4 Medium
5 High
6 Very high

Efficient Use of your Hob
The hob is equipped with zones of different sizes, designed to accommodate most shapes and sizes of pan. For best
results, only use pans with flat bottoms and choose an appropriate zone depending on the size of the pan. The most ef-
ficient use of the hob is shown below, where the pan and zone are correctly chosen.
Use pan lids where possible to minimize the energy usage of your appliance.
It is very important that the pans used on the hob are made of a suitable material and have the correct type of base. The
base should be flat and smooth, as any rough part on the pan base could scratch the ceramic hob top.
Choose pans which are between the sizes recommended in the table above, and with bases that are as non-reflective as pos-
sible, e.g. dull and dark.
Only pans recommended for use on ceramic hobs should be used.
Zone Size
160mm
190mm
180
210
130
170
Fig.2
4
Minimum Pan Size (mm) Maximum Pan Size (mm)

Types of residues Clean with Cleaning advice
Light Cleaning sponge and soft cloth Wipe over the zone to be cleaned with a sponge and hot
water, and then wipe off with a soft dry cloth.
Accumulated baked-on stains/
dirt, sugar spills or melted plastics Cleaning sponge or glass scraper and soft cloth
Wipe over the zone to be cleaned with a sponge and hot
water, using a ceramic scraper to remove any large marks
or stains and then wipe off with a soft dry cloth.
Rings and hard water residues White vinegar and soft cloth Pour a small amount of warm white vinegar onto the stain,
leave it to stand, and then wipe off with a soft dry cloth.
9 fast frying steaks
Care and Maintenance
Always disconnect the appliance from the power supply before undertaking any cleaning or maintenance.
You should use a non-abrasive cleaner to clean the hob top. Any abrasive cleaner (including Cif) will scratch the surface and
could erase the control panel markings.
Important:
• Steam cleaners must not be used when cleaning this appliance.
Mains electrical voltage:
Total rated electrical consumption:
If your Hob is not working:
1. Check that the control knobs are switched on.
2. Check that the mains supply has not been switched off.
3. Check that the fuse in the spur has not blown.
Contact CDA Customer Care
A : Customer Care Department, The CDA Group Ltd, Harby Road, Langar, Nottinghamshire, NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu
5
5.8 kW
230 - 240 Vac

6
Mains Electricity Connection
Warning! this appliance must be earthed
We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who
will comply with the I.E.E. and local regulations.
This appliance is intended to be connected to fixed wiring and is not suitable for connection to a 13a plug or
13a supply.
This appliance is intended to be connected to fixed wiring by a double pole switch, having a contact separation of at
least 3mm in all poles. The switch must be positioned no further than 2m from the appliance.
Please note:
• The mains cable must only be replaced by a qualified electrician or service engineer and must be of equivalent or
better rating (i.e. 2.5mm2, HO5RR-F).
• This appliance is intended to be connected to the mains supply with a cable of cross section area 2.5 mm2. A larger
cable will not fit the terminal connections.
• The marking of the current rating of the fuse or circuit breaker protecting this appliance should be marked on the
socket outlet.
• Assembly and electrical connection should be carried out by specialised personnel.
• When installing this product we recommend you seek the help of another individual.
• Ensure that the brass links are securely fitted. Failure to do so will prevent the hob from operating correctly.
Fig.3

Fitting the Hob
Unpacking the hob: •
Take care not to lose or mishandle any parts.
Fitting position of the hob:
This appliance must be installed a minimum of 50mm from any back wall and a minimum of 190mm away from any
adjacent vertical surfaces, e.g. a tall cupboard end panel. This may be reduced to 100mm if the adjacent surface is resistant
to fire (tiles or steel, for example). These dimensions are shown in Fig.4.
If fitting a cooker hood above the hob:
If a cooker hood is to be installed above the hob, the height of the hood above the hob must be at least 600mm (650mm is
recommended) (Fig.5). If the instructions supplied with the hood dictate that the hood must be installed at a height greater
than 600mm, then that height is the minimum required.
Wall furniture requirements:
The minimum height of any cabinet immediately above the hob is 900mm. The minimum height of any adjacent units
(including light pelmets) is 400mm, unless they are manufactured from a material resistant to fire (steel, for example)
Notes:
• Do not position this appliance above a refrigeration unit. The heat generated may cause the refrigeration unit to fail.
• This appliance is designed to be installed into cabinet units capable of withstanding temperatures of 65°C or greater above
ambient temperature.
• If there is no oven to be built in below the hob, an isolation shelf should be fitted to protect the user from high
temperatures. If the hob is to be installed above a working drawer, then a partition should be fitted to protect the contents
and user from the heat generated during use. This should be fitted 100mm below the hob.
• Never place perishable foods in the cupboard below the appliance.
7

How to Install the Hob
How to install the hob:
Overall dimensions of the hob: Width: 580mm Depth: 510mm
Worktop cut-out dimensions: Width: 560mm Depth: 490mm
1. Make the required hole in the worktop. Before doing this, you must check the instructions supplied with any cooker hood
to ensure that you will have the required clearance. The cut-out (Fig.4) shows a 60mm gap from the wall to the cut-out
edge. The distance from the hob, when fitted, to the back wall is 50mm. If a splashback/worktop upstand is to be fitted,
take this into account when cutting the hole. The minimum distance that the hob should be positioned away from the rear
wall or splashback is 50mm.
2. Position the hob seal, as shown in Fig.6, ensuring that the ends meet without overlapping. Do not use silicone type sealant.
3. Secure the hob to the worktop using the fixing brackets and screws supplied, as shown in Fig.7. Remove any excess sealant
after tightening the brackets. Do not over-tighten the fixing brackets.
3cm 4cm
65mm
470mm
550mm
150mm150mm
Fig.4 Fig.5
400mm
650mm
185mm 185mm
60mm
560mm
190mm190mm
Fig.6 Fig.7
8
480mm

Notes :
0220 HCG500 HCG520 Manual.indd 11 26/6/09 09:35:51