Cecilware ICAP-MINI Quick start guide

1
GOURMET HOT BEVERAGE DISPENSER
Models:
ICAP1
ICAP1-P
ICAP-MINI
WHIPPER
WHIPPER MINI
OPERATIONAL MANUAL
Specifications
Installation & Operating Instructions
Adjustments
Care & Maintenance
Trouble Shooting Guide
Wiring Diagram
Parts List
Cecilware sells value...
Worldwide.
43-05 20th Avenue, Long Island City, NY 11105 · 718-932-1414
FAX: ·718-932-7860
THIS EQUIPMENT IS TO BE INSTALLED TO COMPLY WITH
THE APPLICABLE FEDERAL, STATE, OR LOCAL PLUMBING
CODES HAVING JURISDICTION.
IN ADDITION:
1. A QUICK DISCONNECT WATER CONNECTION OR
ENOUGH EXTRA COILED TUBING (AT LEAST 2X
THE DEPTH OF THE UNIT) SO THAT THE MACHINE
CAN BE MOVED FOR CLEANING UNDERNEAT H.
2. AN APPROVED BACK FLOW PREVENTION DEVICE,
SUCH AS A DOUBLE CHECK VALVE TO BE INSTALLED
BETWEEN THE MACHINE AND THE WATER SUPPLY.
NA64A 6/99

2
MODELS: ICAP 1 B LD WHIPPER B ICAP1 B LD ICAP B LD WHIPPER B
STORAGE CAPACITY
Hopper Capacity [lb.] 8 8 8 8 8
Tank Capacity [gal.] 1.5 1.5 1.5 0 .6 0.6
PRODUCTION CAPACITY
Continuous Draw Rate [oz/drinks/min.]
[drinks / hour]
2 (6 oz.) drinks/min
120
2 (6 oz.) .
120
2 (6 oz.)
120
2 (6 oz.)
60
2 (6 oz.)
60
Burst Capacity [oz.], drinks 28 (6 oz.) 28 (6 oz.) 28 (6 oz.) 12 (6 oz.) 12 (6 oz.)
BURST CAPACITY - Max. number of drinks dispensable with available hot water - based on 6 oz. cup.
FLOW ADJUSTMENT RATE: 1 oz./sec.
STRENGTH ADJUSTMENT RANGE: 22 - 34 gr/(6 oz.) drink
RECOVERY TIME: 10 - 18 drinks [min.]
DISPENSING RATE: [1 oz./sec.]
DIMENSIONS & CONNECTIONS
Height [inches]: 23+2.5” legs 23+2.5” legs 23+2.5” legs 23+1” feet 23+1” feet
Width [inches]: 9 9 9 9 9
Depth [inches]: 21 21 21 16 16
CABINET MATERIAL: Powder Coated Steel *Optional
WATER INLET CONNECTION: 1/4” Male Flare
WATER PRESSURE REQUIRED: 30 -120 psi (2.1 - 8.6 kg/cm2 )
ELECTRICAL
Voltage: 110V or 220 V 110V or 220 V 110V or 220 V 110V or 220 V 110V or 220 V
Frequency: 60 Hz/50Hz 60 Hz/50Hz 60 Hz/50Hz 60 Hz/50Hz 60 Hz/50Hz
Phase: Single Single Single Single Single
Max. Amps: 15 A @ 115 V 15 A @ 115 V 15 A @ 115 V 15 A @ 115 V 15 A @ 115 V
Heater Wattage [kw]: 1.7 1.7 1.7 1.5 1.5
SPECIFICATIONS
FRONT VIEW
MIXING CHAMBER
PRODUCT GUIDE CLEANING LABEL
POWER CORD TO
FRONT PANEL
SUPPORT LEGS
PRODUCT HOPPER
EXTENSION
TOP COVER
MIXING CHAMBER
STEAM DEFLECTOR
CHAMBER INSERT
(PLACE INSIDE
MIXING CHAMBER)
GRILL
DRIP TRAY
DRIP TRAY HOLDER
RINSE SWITCH
HEATER LIGHT
HEATER SWITCH
ICAP1 B LD [w/lit door]
WHIPPER B [w/o lit door]
CLEANING LABEL
MINI WHIPPER B [w/o lit door]
ICAP MINI B LD [w/lit door]
FRONT VIEW
DRIP TRAY
DRIP TRAY HOLDER
GRILL
EXTENSION
MIXING CHAMBER
MIXING CHAMBER
STEAM DEFLECTOR
PRODUCT GUIDE
H EAT ER LIGHT
SUPPORT LEGS
POWER CORD TO
FRONT PANEL
RINSE SWITCH
HEATER SWITCH
TOP COVER
PRODUCT HOPPER
Illustration No. 1

3
INSTALLATION REQUIREMENTS for ICAP1 B LD and WHIPPER B:
THIS EQUIPMENT IS TO BE INSTALLED TO COMPLY WITH THE APPLICABLE FEDERAL, STATE, OR LOCAL PLUMBING CODES
HAVING JURISDICTION. IN ADDITION:
1. A QUICK DISCONNECT WATER CONNECTION OR ENOUGH EXTRA COILED TUBING (AT LEAST 2X THE
DEPTH OF THE UNIT) SO THAT THE MACHINE CAN BE MOVED FOR CLEANING UNDERNEATH.
2. AN APPROVED BACK FLOW PREVENTION DEVICE, SUCH AS A DOUBLE CHECK VALVE TO BE INSTALLED
BETWEEN THE MACHINE AND THE WATER SUPPLY.
INSTALLATION:
1. Flush inlet water line thoroughly before connecting. If pipe sealant is necessary, teflon tape is commended.
2. Connect water line to the 1/4” flare fitting located at rear of the unit. A shutoff valve in the water supply line is advisable.
3. Check that heater switch is in the OFF position. Switch is located below DOOR ASSEMBLY lower right side corner.
4. Turn on water. Check water line and fittings for leaks.
5. Plug the power cord into a grounded 120 volt, 60 Hz 15 Amp outlet, Single use. Press and hold Rinse Button until water
flows through mixing chamber. It will take 2 to 4 minutes to fill the tank.
6. Fill hopper with DRY* powdered cocoa mix or cappuccino product. See filling instructions.
7. Turn heater switch on and allow 10 to 15 minutes for water to heat.
8. Push on Dispensing Button and check the operation of the hopper. A grinding noise will be heard if not properly engaged.
Go to Troubleshooting Guide.
9. Push on Dispensing Button and check the operation of the mixing chamber (for ICAP1 & Whipper ).
A scratching noise will be heard if whipper blade is not properly aligned. Go to Troubleshooting Guide.
10. Push Dispensing Button and check drink taste.
If adjustments are needed, see “Adjustments”.
DISPENSER OPERATION
FILLING
1. Open Front Door.
2. Lift Top Cover.
3. Fill hopper to desired level with DRY*
Powdered cocoa mix or cappuccino.
Do not overfill or pack product down when filling.
4. Close Top Cover and Door.
DISPENSING
1. Place cup under mixing chamber spout.
2. a) For Manual Units (without Timer):
Press and hold push button until cup is approximately 2/3 full.
b) For Automatic Units (with Timer):
Press and release push button. Cup will fill to size set on Timer.
3. Remove cup when flow from mixing
chamber has stopped completely.
*Moist product will clog hopper and the unit will not operate
properly.
Illustration No. 2 – (ICAP 1 B LD & WHIPPER B shown)

4
START UP INSTRUCTIONS FOR ICAP1 POUROVER CAPPUCCINO DISPENSER – see ill. 3
I. INSTALLATION INSTRUCTIONS
This equipment is to be installed to comply with the applicable Federal, State, or local plumbing codes having jurisdiction.
In addition:
1. A quick disconnect water connection or enough extra coiled tubing (at least 2x the depth of the unit) so that the machine
can be moved for cleaning underneath.
2. An approved back flow prevention device, such as a double check valve to be installed between the machine and the wa-
ter supply.
The ICAP1 POUROVER beverage dispenser is equipped with a 3/4” Water Inlet Valve (¼" to 3/4” adapter supplied with the
unit) which is located on the right side in the back of the base (when looking at the machine from the front).
HIGHLY RECOMMENDED: A WATER SHUT-OFF VALVE and A WATER FILTER, preferably a combination Charcoal/Phosphate
Filter, to remove odors and inhibit lime and scale build up in the machine.
Note: In areas with extremely hard water, a water softener must be installed in order to prevent a malfunctioning of the equip-
ment and in order not to void the warranty.
After the machine has been unpacked and placed on a counter, pull out the drip tray and splash guard.
It should contain the following: A Set of 4 Adjustable Leveling Legs & Water Inlet Fitting.
Connect the ¼" dia. copper waterline to the ¼" flare water inlet fitting of the valve.
Caution: Do not plug into power outlet yet. Make sure the Heater Switch is OFF (Toggle Down).
II. PRIMING - MANUAL/BOTTLE POUROVER (Toggle UP, Water Selection Switch, on the back panel)
1. Do NOT plug into power outlet yet.
2. Make sure Heater Switch is in the OFF position, located in back of machine.
3. Fill reservoir tank (top) with 2 gallons of water, wait about 3 minutes for water to fill Heating Tank below.
Refill Top Reservoir Tank with another 2 gallons of water. The unit will NOT dispense unless the Top Reservoir Tank is at
least 1/2 full. So keep Reservoir Tank full.
Note: The unit has a Float (item 3, Ill. 8) inside the Reservoir Tank, which stops the machine from dispensing
when the Reservoir Tank is low.
4. Plug into power outlet.
5. Turn Heater Switch ON.
6. Allow 10 to 15 minutes for water to reach dispense temperature of 190°F. Heater Indicator Light (red) goes ON when
heater is on (see lower front panel).
7. Fill hopper with product.
8. Place cup under dispenser.
9. Push and hold Dispense Button (green) until water flows from mixing chamber.
10. Machine is primed and ready to go.
III. PRIMING INSTRUCTIONS FOR ICAP1 POUROVER
PRIMING - AUTOFILL (Toggle Down,Water Selection Switch, on the back panel)
1. Plug into power outlet.
2. Turn Heater Switch ON.
3. Allow 10 to 15 minutes for water to reach dispense temperature of 190°F.
Heater Indicator Light (red) goes ON when heater is on (see lower front panel).
4. Fill hopper with product.
5. Place cup under dispenser.
6. Push and hold Dispense Button (green) until water flow s from mixing chamber
7. Machine is primed and ready to go.

5
IV. POUROVER-PORTABLE BOTTLE OPERATION (Toggle UP, Water Selection Switch, on the back panel)
UNIT CAN BE OPERATED WITH A 3 GALLONS CAPACITY FRESH WATER BOTTLE.
TO OPERATE WITH PORTABLE BOTTLE, proceed AS FOLLOWS:
1. Remove Reservoir Tank Cover.
2. Make sure that Reservoir Tank is only 1/2 full or empty, to prevent water splillage.
To remove excess water push dispense button.
3. Fill bottle with water .
4. Invert bottle into reservoir tank in one motion to minimize spillage.
5. Remove and refill bottle when “REFILL“ light is ON.
NOTE: REFILL LIGHT, ON THE FRONT DOOR PANEL, WILL GO ON, WHICH INDICATES THAT THE WATER TANK MUST
BE REFILLED. WHEN REFILL LIGHT GOES ON, THE UNIT WILL NOT DISPENSE UNTIL TANK IS FILLED WITH WATER.
REFILLING WITH HOT TAP WATER WILL SHORTEN HEAT UP TIME.
V. NORMAL OPERATION
(POUROVER AND AUTOREFILL)
1. Place a 6 oz. or larger cup under dispense nozzle,
then press and hold dispense switch (green) for 6
seconds.
The machine will dispense water at the rate of 1 oz.
per second. Repeat it several times to check for con-
sistent output.
2. While the tank is heating up, remove the hopper,
load with product and reposition it back in the ma-
chine.
When Heater Light goes OFF, the tank has reached
its brew temperature and the machine is ready to
begin dispensing the first cup of Cappuccino.
VI. WATER FLOW and
DRINK STRENGTH ADJUSTMENTS
THE UNIT IS FACTORY ADJUSTED TO DISPENSE
WATER AND POWDER AT THE RATE OF 1.0 oz/
sec.
TO INCREASE OR DECREASE FLOW, PROCEED AS
FOLLOWS:
1. Remove left side panel and locate Dispense Valve
Flow Adjuster on top of Heated Tank.
2. Locate Flow Adjustment Screw (white) on Dispense
Valve.
3. Rotate Adjustment Screw Counterclockwise to IN-
CREASE flow rate.
4. Rotate Clockwise to DECREASE flow rate.
When making strength adjustments, do not adjust
by more than 1/4 turn at a time, without checking
drink strength (ratio of water to powder).
WATER FLOW
ADJUSTMENT,
SCREW ON
DISPENSE
VALVE
RESERVOIR
TANK
RESERVOIR
COVER
INDICATOR
LIGHT- RED
"REFILL TANK
WHEN ON"
DISPENSE
BUTTON
BOTTLE
HOT WATER TANK
DRIP TRAY
Illustration No. 3 – ICAP 1 B LD POUROVER

6
A. TO ADJUST PRODUCT THROW (ILL # 4)
1. Open Door Assembly and remove Steam Deflector
by pulling it forward.
2. To make adjustment use a screwdriver with 1/2 inch
wide blade. Engage product adjuster as shown below
and turn as follow.
3. Turn clockwise to increase drink strength or
counter-clockwise to reduce it.
Check drink strength after every half a turn.
If after maximum adjustment, drink taste is not as
desired proceed to adjust the water flow according to
procedure B below.
4. Re-install Steam Deflector.
B. TO ADJUST WATER FLOW RATE (ILL. # 5 )
1. Remove right hand side cover of the unit.
(looking at the unit from the front)
2. Locate Flow Adjustment Key inside unit mounted
above water valve.
3. Engage Flow Adjustment Key into Flow Controller
and rotate counterclockwise to decrease
and clockwise to increase drink strength.
When making strength adjustments, do not turn
Adjustment Key more than 1/8” at a time without
checking drink strength.
4. Return Adjustment Key back into keyholder.
If after maximum adjustment, drink taste is still not
strong as desired, take auger spring out of the hopper and re-
move the product adjuster.
C. DRINK SIZE ADJUSTMENT (ILL. # 6)
(AUTOMATIC UNITS - WITH TIMER)
1. Remove right side panel.
2. Turn knob on Timer right to increase or left to decrease drink size.
The number 6 on the Timer indicates approximate drink size at a
factory setting of 1 oz./sec. flow rate.
3. Press push button and check drink size. Repeat if
necessary, until desired drink size is dispensed.
4. Replace the side panel.
Illustration No. 5 – Water Inlet Valve
Illustration No. 4 – Product adjuster
Illustration No 6 - Timer
DRINK STRENGTH ADJUSTMENTS
NOTE: The unit has been factory preset to deliver water at 1 oz. per second

7
Illustration No. 7
SLINGER DISC
INSERT
CHAMBER
MIXING
PRODUCT SHUTE
MIXING CHAMBER MOUNT
MIXER BLADE
EXTENSION
CHAMBER
MIXING
CHAMBER
MIXING
DEFLECTOR
STEAM
HOPPER ASS'Y
PRODUCT
SWITCH
HEATER
DRIP TRAY BRACKET
DRIP TRAY
GRILL SWITCH
RINSE
TOP COVER
MIXING CHAMBER PLATE
MIXING CHAMBER SPACER
DRIP TRAY BRACKET SEAL (GASKET)
HEATER
SWITCH
SWITCH
RINSE
HOPPER ASS'Y
PRODUCT GUIDE
EXTENDER
CHAMBER
DEFLECTOR
CHAMBER
WING NUT
CLEANING INSTRUCTIONS
GRILL
DRIP TRAY
MIXING
STEAM
MIXING
ICAP MINI B LD (with Lit Door)
MINI WHIPPER B (without Lit Door)
TOP COVER
CLEANING INSTRUCTIONS
NB04A
WHIPPER B (without Lit Door)
ICAP1 B LD (with Lit Door)
CLEANING INSTRUCTIONS
CLEANING INSTRUCTIONS
NA62C
OPTIONAL
DAILY:
1. Wipe exterior of dispenser with a soft damp cloth.
Deflector setup by pulling forward.
2. Disengage Product Hopper by lifting straight up,
while retaining in the upright position.
3. emove Mixing Chamber by turning Counterclockwise
and pulling forward.
A. emove Mixing Chamber Insert by pulling up.
B. emove Mixing Chamber Extension by pulling down.
4. emove Mixer Blade by pulling forward.
5. Wash Grill, Mixer Blade, Insert, Extension, and Mixing
Chamber with a mild detergent.
6. Wipe upper compartment with a damp cloth.
7. eplace all parts including Hopper.
8. Dry thoroughly before reloading with product.
DAILY:
1. Wipe exterior of dispenser with a soft damp cloth.
Deflector setup by pulling forward.
2. Wash Drip Tray with hot water.
3. Flush Mixing Chamber by depressing inse Button
approximately 10 seconds.
WEEKLY:
NOTE: IN VE Y HIGH VOLUME LOCATIONS, THIS
P OCEDU E SHOULD BE DONE TWICE A WEEK.
1. Open Top Cover, Door Assembly, and remove Steam
Deflector setup by pulling forward.
2. Disengage Hopper by lifting straight up,
while retaining in the upright position.
3. emove Mixing Chamber by unscrewing wing nuts.
4. Wash all components after removing.
5. Wipe upper compartment with a damp cloth.
6. eplace all parts including Hopper.
7. Dry thoroughly before reloading with product.

8
TROUBLE PROBABLE CAUSE REMEDY
Light Display does not go on.
No power
a) Dispensing unit unplugged
b) No power from terminal block
a) Reconnect dispensing unit
b) Check the terminal block for loose wire
No water when Rinse Switch
is depressed
a) Water supply off
b) Clogged inlet screen (water valve)
a)Turn on water
b) Disconnect water line and clean inlet screen
No product when Dispense
Button is depressed
a) No product in hopper
b) Auger spring not working
c) Inoperative auger motor
d) Hopper outlet clogged
a) Add product if auger spring is moving
b) Engage hopper to auger motor’s gear
Replace damaged coupling if needed
Check connections of motor, relay and/or
switch, if needed replace such component.
d) Clean hopper and dry thoroughly
Water does not shut off a) Leaking inlet water valve
b) Malfunctioning Timer
c) Inoperative dispense switch
a) Clean and check all fittings of water valve.
Replace water inlet valve
b) Replace Timer (automatic units only)
c) Check switch connections. Replace dispense switch
Drink too strong a) Water flow too low
b) Product throw too high
a) Adjust water flow (see To Adjust Water Flow Rate)
b) Adjust product throw (see To Adjust Product Rate))
Drink too weak a) No product in hopper
b) Product throw too low
a) Add product
b) Adjust product throw (see To Adjust Product Rate)
Water drips from mixing
chamber
a) Temperature too high
b) Leaking inlet water valve
c) Too much water in tank’s
a) Adjust the thermostat accordingly
b) Check fittings, if needed replace water valve
c) Remove tank top and clean holes in inner
Cold drink a) No hot water
b) Run out of hot water
c) Tank does not heat up
a) Allow tank to heat
b) Allow tank to heat after filling
c) Check for loose wire on either thermostat
or heating element. Replace either or
Drink not whipped a) No whipper blade
b) Whipper blade stuck
c) Inoperative whipper motor
a) Replace whipper blade
b) Check blade alignment, if needed replace
blade and mixing chamber
c) Replace whipper motor
Noise coming from mixing
chamber
Whipper blade not properly aligned Check blade alignment, if needed replace blade and mix-
ing chamber
Light Display does not go on Defective light bulb and/or ballast. Check for loose wire or properly plugged light bulb.
Grinding noise coming from
unit
Hopper not properly engaged Check the mating between the auger motor’s gear and
hopper’s coupling
Dispenser repeats cycle. a) Malfunctioning Timer.
b) Malfunctioning Dispense Switch
a) Replace Timer (automatic units only)
WARNING: To reduce the risk of electrical shock unplug the dispenser power cord before repairing or replacing any
internal components of the unit. Before any attempt to replace a component be sure to check all electrical
TROUBLESHOOTING PROCEDURE

9
DESCRIPTION AND LOCATION OF COMPONENTS
ICAP1 B LD (with lit door) & WHIPPER B (without lit door)
Illustration No. 8

10
COMPONENTS IDENTIFICATION
ITEM DESCRIPTION P/N ITEM DESCRIPTION P/N
1 TANK TOP ASSY 97127 36 SLINGER DISC 83034
2 SILICONE TUBING 77184 37 "O" RING ?
3 DISCHARGE TUBE ASSY 97122 38 MIXING CHAMBER MOUNT 83033
4 DISCHARGE TUBE BRACKET 73277 39 MIXER BLADE 90230
5 NOZZLE BRACKET RE81A 40 MIXING CHAMBER EXTENDER TUBE 77184
6 TANK BAFFLE ASSY 97198 41 MIXING CHAMBER 95001
7 TANK BAFFLE SEAL 20039 42 MIXING CHAMBER INSERT 83036
8 TANK CLAMP ASSY 97131 43 LAMP HOLDER MOUNTING BRACKET (lit door) RE52A
9 HEATER ELEMENT 1750W 120V G0140 44 BALLAST (for lit door only) CE221
10 WASHER, HEATER ELEMENT 07059 45 PRODUCT SWITCH L455C
11 NUT HEATER ELEMENT 03051 46 LAMP SOCKET - LEVITTON ( for lit door only) 44496
12 TANK LIMIT 97293 47 FLOURESCENT LAMP 9W ( for lit door only) L024A
13 HI-LIMIT TEMPERATURE CONTROL 59024 48 DOOR WELDMENT ASSY - ICAP 1 B LD (w/lit door) RC53Q
14 ELBOW, MALE 1/8 NPT X 1/4 09246 49 AUGER MOTOR BRACKET 73272
15 CONTROL THERMOSTAT 59016 50 AUGER MOTOR 115V 52037
16 TOP FRONT COVER RC42C 51 SUPPORT PLATE F/AUGER MOTOR 90209
17 HOSE BARB FITTING K435C 52 GEAR AUGER DRIVE MOTOR GEAR, PLASTIC 90208
18 ADJ. VALVE ASSY #H5107 NPT K415A 53 O RING 20015
19 HOSE NUT 95101 54 CARTRIDGE HEATER 20W 87024
20 WATER VALVE INLET ASSY L477A 55 HEAT DUCT 97135
21 POWER CORD 44242 56 PRODUCT DISPENSER ADAPTER CD70C
22 TIMER, OPTIONAL - (for automatic units only) 120v
TIMER, IPTIONAL - (for automatic units only) 220v
58017
58019
57 STEAM DEFLECTOR 90272
23 TERMINAL BLOCK SINGLE B135A 58 RESTRICTOR 92173
24 RELAY (for automatic only) 120v B129A 59 RESTRICTOR RETAINER 34007
25 BODY FRAME WELDMENT ASSY RE80Q 60 PRODUCT ADJUSTER 71001
26 Legs, set 2.5" BLK M034C 61 AUGER SPRING 95116
27 STUD DRIPTRAY 92007 62 AUGER DRIVE COUPLING, PLASTIC 90211
28 DRIP TRAY PAN 75060 63 HOPPER & BASE ASSY 97098
29 GRILL 75015 64 AGITATOR DRIVE GEAR 90268
30 DRIP TRAY BRACKET (HOLDER )(OPTIONAL) RE73A 65 AGITATOR 40692
31 RINSE SWITCH 56039 66 PIN/STUD HOPPER 04026
32 HEATER SWITCH L299C 67 GEAR AUGER DRIVE (HOPPER BASE), PLASTIC 90210
33 HEATER INDICATOR LIGHT AMBER C002C 68 RETAINER PIN, STEEL (UNDER HOPPER) 04025
34 WHIPPER MOTOR 115V 52038 69 RETAINER PIN, S/STEEL (on coupling) 04030
35 WHIPPER MOTOR BRACKET PLATED 92177 70 SIDE PANEL RC40A

11

!
"
#
$
%
&
'
"
#
!
"
"
"!
""
"#
"$
"%
"&
"'
#
#
#
#!
#$
#&
#'
$
$
$
$!
$#$$$%$'%%
%
$"
DESCRIPTION AND LOCATION OF COMPONENTS
ICAP1 B LD POUROVER (with lit door)
$&
!



'   " # $ % & ' ! ! ! !! !" !# !$ !% !& !' "&%$
$ % & '   ! " # $ % & ' ! ! ! !! !" !# !$ !% !& !' "
#%
##
#"
Illustration No. 9

12
ICAP1 B LD POUROVER (with lit door]
ITEM DESCRIPTION P/N ITEM DESCRIPTION P/N
1. COLD TANK COVER ASS'Y Q164A 37. SLINGER DISC 83034
2. COLD WATER TANK WELDMENT ASS'Y Q163Q 38. “O” RING ?
3. WATER LEVEL FLOAT/CONTROL SWITCH (COLD) L499A 39. MIXING CHAMBER MOUNT 83033
4. TANK TOP ASS'Y (FOR HOT WATER TANK) Q166Q 40. MIXER BLADE 90230
5. DISPENSE (DUMP) VALVE (MULLER) L467A 41. MIXING CHAMBER EXTENDER TUBE 77184
6. TANK BAFFLE ASS'Y 97128 42. MIXING CHAMBER 95001
7. TANK CLAMP SEAL 20039 43. MIXING CHAMBER INSERT 83036
8. TANK CLAMP ASS'Y 97131 44. LAMP HOLDER MOUNTING BRACKET ( Lit Door ) RE52C
9. HEATER ELEMENT 1750W 120V G0140 46. BREW SWITCH L455A
10. WASHER, HEATER ELEMENT 07059 47. LAMP SOCKET - LEVITTON (for Lit Door only) 44496
11. NUT, HEATER ELEMENT 03051 48. FLUORESCENT LAMP 9W (for Lit Door only) L042A
12. HOT WATER TANK WELDMENT ASS'Y Q165Q 49. DOOR WELDEMENT ASS'Y - ICAP1 B LD POUROVER RC53Q
13. HI-LIMIT TEMPERATURE CONTROL 59024 50. TOP FRONT COVER RC42A
14. ELBOW, MALE 1/8 NPT X 1/4 09246 51. AUGER MOTOR BRACKET 73272
15. CONTROL THERMOSTAT 59016 52. AUGER MOTOR 115V 52037
16. HOSE NUT 95101 53. O RING 20015
17. WATER VALVE INLET ASS'Y L477A 54. GEAR, AUGER DRIVE MOTOR GEAR, PLASTIC 90208
18. HEATER SWITCH L299A 55. SUPPORT PLATE F/AUGER MOTOR 90209
19. AUTO REFILL SWITCH L299A 56. CARTRIDGE HEATER 20W 87024
20. POWER CORD 44242 57. HEAT DUCT 97135
21. LEGS, SET 2.5" BLK M034A 58. PRODUCT DISPENSER ADAPTER CD70A
23. RELAY (DOUBLE POLE-on at all times) 120V L018A 59. STEAM DEFLECTOR 90272
24. TERMINAL BLOCK SINGLE B135A 60. RESTRICTOR 92172
25. BODY FRAME WELDMENT ASS'Y RI88Q 61. RESTRICTOR RETAINER 34007
26. POWER SWITCH (TOGGLE) L069A 62. PRODUCT ADJUSTER 71001
27. POWER INDICATOR LIGHT, (red) C165A 63. AUGER SPRING 95116
28. GRILL 75015 64. AUGER DRIVE COUPLING, PLASTIC 90211
29. DRIP TRAY PAN 75060 65. HOPPER & BASE ASS'Y 97098
30. DRIPTRAY BRACKET (HOLDER)(OPTIONAL) RE73A 66. AGITATOR DRIVE GEAR 90268
31. STUD, DRIPTRAY 92007 67. AGITATOR 40692
32. HEATER INDICATOR LIGHT AMBER C002A 69. GEAR AUGER DRIVE (HOPPER BASE), PLASTIC 90210
33. RINSE SWITCH 56039 70. RETAINER PIN, STEEL (under Hopper) 04025
34. INDICATOR LIGHT, GREEN "out of water/refill tank" C072A 71. RETAINER PIN, S/STEEL (on Coupling) 04030
35. WHIPPER MOTOR 115V 52038 72. SIDE PANEL RC40A
36. WHIPPER MOTOR BRACKET PLATED 92177
68. PIN/STUD HOPPER 04026

13
Illustration No. 10
ICAP MINI B LD (w/Lit Door) and MINI WHIPPER B (w/o Lit Door)
DESCRIPTION AND LOCATION OF COMPONENTS
!
"
#
$
%
&
'



!
"
#
$
%
&
'

 ! " # $ % & ' ! ! ! !! !" !# !$
!&
!'
"
"
"
"!
""
"#
"$
"%
"&
"'
#
#
#
#!
#"
##
#$
#%
#&
#'
$
$
$
$!
$"$#$$$%$&

!%

14
ICAP MINI 1 B LD w/lit door) & MINI WHIPPER B (w/o lit door)
ITEM DESCRIPTION P/N ITEM DESCRIPTION P/N
1 TANK TOP ASSY W/QC 97166 35 PLATE - MIX CHAMBER 40138
2 SILICONE TUBING (HOSE) 77216 36 SEAL - MIX CHAMBER (GASKET) 20032
3 HOSE CLAMP, METAL 34034 37 WING NUT 03005
4 CHECK VALVE, PLASTIC M323A 38 HOSE BARB S/S 1/4 WITH FITTING K436A
5 TANK BAFFLE ASSY 97170 39 MIXING CHAMBER 97169
6 TANK BAFFLE SEAL 20039 40 EXTENDER-MIXING CHAMBER 83041
7 TANK CLAMP ASSY 97131 41 LAMP HOLDER MOUNTING BRACKET (for lit Door RE52A
8 HEATER ELEMENT 1500W/110V 87037 42 BALLAST (for lit Door only) (CA33C older units CE221
9 WASHER, HEATER ELEMENT 07059 43 PRODUCT SWITCH L455A
10 NUT, HEATER ELEMENT 03051 44 LAMP SOCKET - LEVITTON (for lit Door only) 44496
11 TANK 97165 45 FLOURESCENT LAMP 9W (for lit Door only) L042A
12 HI-LIMIT TEMPERATURE CONTROL 59010 46 DOOR WELDMENT ASSY - ICAP 1 B LD RC53Q
13 DRAIN PLUG, BRASS K044A 47 AUGER MOTOR BRACKET 73272
14 CONTROL THERMOSTAT 59016 48 AUGER MOTOR 115V 52037
15 TOP FRONT COVER RC42A 49 SUPPORT PLATE F/AUGER MOTOR 90209
16 HOSE BARB FITTING K435A 50 GEAR, AUGER DRIVE MOTOR GEAR, PLASTIC 90208
17 ADJ. VALVE ASSY #H5107 NPT K415A 51 O RING 20015
18 HOSE NUT 95101 52 CARTRIDGE HEATER 87024
19 WATER VALVE INLET ASSY L477A 53 HEAT DUCT 97167
20 POWER CORD 44242 54 PRODUCT GUIDE (SHUTE) CD70A
21 TIMER (for automatic units only) 120v 58017 55 STEAM DEFLECTOR 90272
22 TERMINAL BLOCK SINGLE B135A 56 RESTRICTOR 92173
23 BODY FRAME WELDMENT ASSY RG94Q 57 RETAINER 34007
24 LEGS (2.5") BLACK, PLASTIC (OPTIONAL)
RUBBER FEET 1" BLACK (W/O BRACKETS
M034A
18003
58 PRODUCT ADJUSTER 71001
25 STUD-DRIP TRAY 92007 59 AUGER SPRING 95116
26 DRIP TRAY PAN 75060 60 AUGER DRIVE COUPLING, PLASTIC 90211
27 GRILL 75015 61 HOPPER & BASE ASSY 97098
28 BRACKET-DRIP TRAY HOLDER (OPTIONAL W/2.5" LEGS ONLY) RE73A 62 GEAR, AGITATOR DRIVE 90268
29 RINSE SWITCH 56039 63 AGITATOR 40692
30 HEATER SWITCH L299A 64 PIN (STUD) HOPPER 04026
31 HEATER INDICATOR LIGHT AMBER C002A 65 GEAR AUGER DRIVE (HOPPER VBASE), PLASTIC 90210
32 NUT - FOR SPACER 03003 66 RETAINER PIN, STEEL, (UNDER HOPPER) 04025
33 WASHER - FOR SPACER 07007 67 RETAINER PIN, S/STEEL, (ON COUPLING) 04030
34 SPACER - MIX CHAMBER (STUD) 05041 68 SIDE PANEL RC75A

15
AUTOMATIC:ICAP 1 B LD [LIT DOOR] & WHIPPER B [NO LIT DOOR]
AUTOMATIC: ICAP 1 MINI B LD [LIT DOOR] & MINI WHIPPER B [NO LIT DOOR]

16
MANUAL - ICAP 1 B LD [LIT DOOR]
MANUAL - ICAP 1 MINI B LD [LIT DOOR]

17
CONNECT "YELLOW" WIRES TO TIMER TERMINAL "NO".
CONNECT "ORANGE" WIRES TO TIMER TERMINAL "N".
NOTE: TO CONVERT TO TIMER CONTROLLED DISPENSE,
CONNECT "BLUE" WIRE TO TIMER TERMINAL "L1".
USE PIGGY BACK TERMINAL PROVIDED.
DOOR UNIT
INDICATOR LIGHT
"REFILL TANK"
"OUT OF WATER"

18