Cecilware Java 2 QB-D User manual

Page 3
INSTALLATION
Water Inlet Connection:
This equipment is to be installed to comply with the applicable Federal, State, or local plumbing codes having jurisdiction. In
addition:
1. A quick disconnect water connection or enough extra coiled tubing (at least 2 times the depth of the unit) so that the
machine can be moved for cleaning underneath.
2. An approved back flow prevention device, such as a double check valve to be installed between the machine and the water
supply.
The JAVA2-QB-Dis equipped with a 1/4" Flare Water Inlet Fitting, located behind the unit near the bottom.
HIGHLY RECOMMENDED:
A WATER SHUT-OFF VALVE and A WATER FILTER, preferably a combination Charcoal/Phosphate Filter, to remove odors and
inhibit lime and scale build up in the machine. Note: In areas with extremely hard water, a water softener must be installed
in order to prevent a malfunctioning of the equipment and in order not to void the warranty.
STARTUP PROCEDURE
Caution: Make sure that the Heater Switch, located behind unit near the bottom, is in the OFF
(toggle down) position.
1. Connect the 1/4" Dia. copper waterline to the 1/4" flare water inlet fitting of the valve.
2. Connect the power cord into a proper receptacle.
3. Activate the Power Switch (Toggle Up). The tank will start filling. Allow approximately 5 minutes for the tank to fill.
4. Activate the Heater Switch. Allow approximately 20-45 minutes for the water to reach a preset temperature of 200°F.
The heat up time will depend on the water inlet temperature, the input voltage, and the wattage of the elements in the
machine.
5. Place cup under nozzle and press dispense switch, button will light while dispensing. The machine will dispense water at
the rate of 1.3 oz. per second.
Repeat it several times for each dispense switch to check for consistent output.
6. While the tank is heating up, remove the hoppers, load them with products and reposition them back in the machine.
NOTE: Decanter capacity is up to 54 OZ. Cup capacity is up to 12 OZ.

Page 4
PROGRAMMING FOR AUTOMATIC DISPENSE
(See Door diagram)
1. Turn Power Switch ON (toggle switch inside door).
2. PRESS and HOLD [red] STOP Button with one hand.
3. PRESS and HOLD [green] DISPENSE Button with other hand.
4. RELEASE [red] STOP Button ONLY.
5. Continue to HOLD [green] DISPENSE Button until BUZZER
sounds, then RELEASE.
6. PRESS and RELEASE [green] DISPENSE Button.
Product begins dispensing.
When it reaches the “DESIRED VOLUME”,
7. PRESS and RELEASE [green] DISPENSE Button to SET
“DESIRED VOLUME”.
DISPENSE Button can be jogged to top off.
8. PRESS and HOLD [red] STOP Button for 5 Secs. to LOCK IN
“DESIRED VOLUME”.
Repeat steps 1 to 8 for each Dispense Button.
The Automatic Dispense Buttons are factory programmed to dispense
1.3 oz. of water per second.
NOTE:
Set programming for Cup Volume with cup shelf “DOWN”.
Set programming for Decanter Volume with cup shelf “UP”.
PRODUCT STRENGTH ADJUSTMENTS:
The JAVA 2-QBD units have variable speed control auger
motors with variable speed of 10 to 30 RPM.
Drink or Product Strength can be changed by adjusting the
Gram Throw Dial on inside door panel.
The Gram Throw is factory preset at approx. 2.2 gr. per 8 oz.
cup and 15.0 gr. per decanter.
The water flow rate adjustment for the dispense valve
should remain fixed at 1.3 oz per sec.
POWER SWITCH RINSE/ SERVE SWITCH
DISPENSE BUTTONS
DRINK
STRENGTH
ADJUSTMENT
READY LIGHT HEATING LIGHT
PROGRAMMI
NG
INSTRUCTION

Page 5
CLEANING AND SANITIZING:
SANITIZING: All food dispensing units should be sanitized periodically. All parts to be sanitized must be cleaned first.
To prepare a sanitizing solution: ADD 2 TSP. OF LIQUID CLOROX BLEACH (5.25% CONCENTRATION) TO 1 GALLON OF
WATER AT ROOM TEMPERATURE (70°F -90°F).
Soak all parts for a minimum of 3 min. in the sanitizing solution. Note: Always start with an unopened bottle of Clorox
Bleach since the solution from an opened bottle has a short life span.
Let all sanitized parts drain and dry naturally. DO NOT WIPE THEM DRY. Before using the sanitized unit (or parts) with
foodstuffs, rinse all parts thoroughly with water.
CARE FOR STAINLESS STEEL:
STAINLESS STEEL surfaces, that comes in contact with food substances, MUST BE CLEANED EVERY DAY.
WHEN CLEANING STAINLESS STEEL, ONLY A PH NEUTRAL CLEANER IS TO BE USED.
Use nylon or brass brushes (not steel wire brushes) for removing food deposit.
Many food products contain acids, alkalis, or other substances, which corrode Stainless Steel.
RECOMMENDED DAILY CLEANING AND MAINTENANCE
1. Wash cup shelf and warmer dish with dish detergent.
Rinse Chambers:
Flip Toggle SWITCH to RINSE position and press DISPENSE BUTTON.
When done, flip toggle switch back to SERVE position.
Remove and refill Hoppers.
Note: When removing hoppers, turn PRODUCT GUIDE UP to reduce spillage,
return to down position after re-inserting hoppers.
CLEAN HOPPERS (once a week)
1. Turn the product guide up, and remove hoppers.
2. Empty out Hoppers.
3. Pull off Product Guide.
4. Wash parts with dish detergent.
5. Rinse, dry, and re-assemble parts.
CLEAN DISPENSE CHAMBERS (once a week)
1. Twist CW and pull off STEAM DEFLECTOR.
2. Pull off DISPENSE CHAMBER.
3. Wash components with dish detergent.
4. Rinse, dry, and re-assemble parts.

24
25
11
9
17
28
30

1 2
18
32
OVERFLOW
WATER LEVEL
DRAIN WATER INLET
4
3

AUGER MOTOR CD151 83 RPM
PRODUCT GUIDE
WIRE AUGER CD74A
(17mm DIA, 12.0mm PITCH)
AUGER BUSHING FRONT CD306
LABEL NA38A REF
AUGER BUSHING-BACK CD279
HOPPER BASE CD140
BEVELLED SOCKET CD271
NUT CD278 [2]
HOPPER COVER CD106
CD70A

20 CD137 1
MIXING BOWL
SPOUT ASSEMBLY
SOCKET, MIXING BOWL
TEACH-ME TIMER DUAL
25
22
24
23
22
1
1
M935Q
L726A
CD67A
2
1
STEAM CAP
PILOT LIGHT, RED (HEATING) 120V
SPEED CONTROLLER
SILICONE GROMMET, 12 mm
HEATER, 1500W, 120V
PARTS LIST : JAVA 2-QB-D, -D1, -D2, -D3, -DC
THERMOSTAT
10
TOGGLE SWITCH, DPST (POWER ON-OFF)
DISPENSE VALVE
HOPPER
LATCH
TOGGLE SWITCH, SPST (RINSE-SERVE) & (HEATER)
15
19
18
16
17 WATER INLET VALVE 110V
13
14
12
11
RELAY, 120V
HI-LIMIT, 200° CUTOUT
PUSH BUTTON SWITCH (RED STOP)
PUSH BUTTON SWITCH (GREEN DISPENSE)
POTENTIOMETER
PILOT LIGHT, GREEN (READY) 120V
9
9
7
6
3
4
5
2
1
1
L299A 1
L467A
CD61A
CD325
CD257
1
2
2
1
32004
M705A
L069A 1
1
2
L557A
L556A
CH112
B138A
2
2
4
1
L656A
L455A
L574A
L681A
M461A 1
2
1
7
1
G194A 1
LEVEL CONTROL DUAL 120V
26
L690A
27 BLOWER/ FAN 120V
27 CD56A 1
TRANSFORMER, 24V
28 CF29A 2
29
30
31
32
33
WARMER ELEMENT, 120V, 60W
34
G386A
BLOWER HOSE (1" DIA) CD369 1
PRODUCT GUIDE, LEFT CD70A 1
DUAL LEVEL PROBE ASSEMBLY K659Q 1
POWER CORD 120V C032A 1
AUGER MOTOR 24V, 83 RPM CD151 2
RELAY, 220V (FOR 240 V UNITS)
8
B172A 4
BLOWER/ FAN 240V CD166 1
HEATER, 3500W, 240V G197A 1
1
LEVEL CONTROL DUAL 240V L706A
1
1
1
1
1
1
2
2
1
1
1
2
2
2
4
1
1
2
1
7
1
1
1
2
1
1
1
1
1
2
4
1
1
1
1
1
1
2
1
1
1
2
2
1
1
1
2
2
2
4
1
1
2
1
7
1
1
1
2
1
1
1
1
2
4
1
1
1
SPOUT ASSEMBLY
21 M934Q 1
11 __ _
SPOUT ASSEMBLY M864Q __
29 WARMER ELEMENT, 220V, 80W G110A 1
25
34 POWER CORD 220V CH50A 111
PUSH BUTTON SWITCH (AMBER HOT WATER) L457A 1
11
PILOT LIGHT, GREEN (READY) 240V CH260 1
8 11
14 CD55A 1 11
PILOT LIGHT, RED (HEATING) 240V
17 WATER INLET VALVE 220V CD258 1 11
240 VOLT COIL F/DISPENSE VALVE
18 CF38A 222
FUNNEL V274Q _
HOPPER GUIDE SL30A
34
_
2
_
235 WARMER SWITCH, RED L217A 136 SHELF SWITCH 56039 1137 2 2
2
1
1
2
2
1
2
3
2
1
1
1
2
2
2
3
1
1
2
1
8
1
1
1
2
1
2
1
1
2
3
1
1
1
1
1
1
1
1
1
2
2
1
1
1
2
2
2
4
1
1
2
1
7
1
1
1
2
3
1
1
1
1
2
4
1
1
1
_
1
_1
_1
3
_
_
11
1
1
1
1
1
1
1
1
32
1
_
2
31
_
2
_
24 TEACH-ME TIMER SINGLE L576A _2_2_
FUNNEL V270Q
_ _
_
111 1 _
_
_2
2
_ _

N
BLK
L1
N
4
23 13 1
4
2
COFFEE DECAFF
DISPENSE
VALVE
..
DUAL
TIMER
SPEED
CONTROL
D.C.
AUGER
MOTOR
SPEED
CONTROL
D.C.
AUGER
MOTOR
WATER INLET
VALVE
VACUUM FAN
THERMOSTAT HEATER SW
HI-LIMIT
DOOR UNIT
HEATING
READY
POWER STOP SWITCH
RED
WHT
BLU
YEL
GRN
HOTWATER
HOT
WATER
VALVE
TIMER SW
K3
K4
RINSE
JE 1 : 1
E
K2
RELAY
COIL
WATERLEVEL
PROBES
LIQUID LEVEL CONTROL
WATER
K1
RELAY
COIL
3
5
K1
RELAY DUAL
TIMER
3
5
K2
RELAY
WARMER
3 PIN CONNECTOR WARMER SWITCH
OPTIONAL

N
BLK
L1
N
4
23 13
1
4
2
COFFEE DECAFF
DISPENSE
VALVE-1
SPEED
CONTROL
D.C.
AUGER
MOTOR
SPEED
CONTROL
D.C.
AUGER
MOTOR
WATER INLET
VALVE
VACUUMFAN
THERMOSTAT HEATERSWHI-LIMIT
DOOR UNIT
HEATING
READY
POWER STOP SWITCH
WARMER
3PIN
CONNECTOR
RED
WHT
BLU
YEL
GRN
HOTWATER
HOT
WATER
VALVE
PROGRAMMINGSW.CUP/ DECANTER
K3
K4
RINSE
K5
K5b
K5a
TEMP.
LOCKOUT
K2
RELAY
3
5DUAL
TIMER
DUAL
TIMER
3
5
K1
RELAY
K2
RELAY
COIL
K1
RELAY
COIL
WARMER
SWITCH WARMER
CUTOUT
SWITCH
OPTIONAL

N
BLK
L1
N
4
23 1
3
1
4
2
COFFEE DECAFF
DISPENSE
VALVE-1
DUAL
TIMER
SPEED
CONTROL
D.C.
AUGER
MOTOR
SPEED
CONTROL
D.C.
AUGER
MOTOR
WATER INLET
VALVE
VACUUMFAN
THERMOSTAT HEATERSWHI-LIMIT
DOOR UNIT
HEATING
READY
POWER STOP SWITCH
WARMER
3PIN
CONNECTOR
RED
WHT
BLU
YEL
GRN
WARMER
CUTOUT
SWITCH
HOTWATER
HOT WATER
VALVE
OPTIONAL
K3
RINSE
DISPENSE
VALVE-2
PROGRAMMINGSW.CUP/ DECANTER
DUAL
TIMER
K2
RELAY
COIL
K1
RELAY
COIL
3
5
K1
RELAY K2
RELAY
3
5
WARMER
SWITCH

N
BLK
L1
N
4
23 13 1
4
2
COFFEE DECAFF
DISPENSE
VALVE
..
SPEED
CONTROL
D.C.
AUGER
MOTOR
SPEED
CONTROL
D.C.
AUGER
MOTOR
WATER INLET
VALVE
VACUUM FAN
THERMOSTAT HEATER SW
HI-LIMIT
DOOR UNIT
HEATING
READY
POWER STOP SWITCH
RED
WHT
BLU
YEL
GRN
HOTWATER
HOT
WATER
VALVE
K3
K4
RINSE
M.M. 1 : 1
A
K2
RELAY
COIL
WATERLEVEL
PROBES
LIQUID LEVEL CONTROL
WATER
K1
RELAY
COIL
3
5
K1
RELAY TEACH ME
TIMER
3
5
K2
RELAY
TEACH ME
TIMER
WARMER
3 PIN CONNECTOR WARMER SWITCH
OPTIONAL