Cedar Summit F24720 User manual

INSTALLATION AND OPERATING INSTRUCTIONS
GRANDVIEW LODGE PLAY SYSTEM – F24720
10-14 Hrs
To reduce the risk of serious injury or death, you must read and
follow these instructions. Keep and refer to these instructions often
and give them to any future owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 26’ x 31’6” area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6’5”
CAPACITY - 9 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
Two person
assembly
WARNING
7'-4"
19'6"
31'-6"
26'
3404720 Rev 02/11/2013
Table of Contents
Warnings and Safe Play Instructions. . . . . . . . . . . . . . . pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance . . . . . . . . . . . . . . . pg. 4
About Our Wood – Limited Warranty . . . . . . . . . . . . . . pg. 5
Keys to Assembly Success . . . . . . . . . . . . . . . . . . . . . . pg. 6
Metric Conversion Sheets . . . . . . . . . . . . . . . . . . . . . pg. 7,8
Part ID .......................................pg. 9
Installation of I.D./Warning Plaque . . . . . . . . . . . .Final Step
Cedar Summit
c/o ©Solowave Design L.P
Mount Forest, ON Canada
N0G 2L0
www.cedarsummitplay.com
[e-mail]
Customer Service
1-877-817-5682 (toll free)
1-519-323-2258

 2 [email protected]
Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
Observe capacity limitations of your play-set. See
front cover.
Dress children with well fitting and full foot enclosing
footwear.
Teach children to sit with their full weight in the center
of the swing seat to prevent erratic swing motion or
falling off.
Check for splintered, broken or cracked wood; missing,
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
Verify that suspended climbing ropes, rope ladders, chain
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
On sunny and or hot days, check the slide and other
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
Do not allow children to wear open toe or heel footwear
like sandals, flip–flops or clogs.
Do not allow children to walk, in front, between, behind
or close to moving rides.
Do not let children twist swing chains or ropes or loop
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
Do not let children get off rides while they are in motion.
Do not permit climbing on equipment when it is wet.
Do not permit rough play or use of equipment in a
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
Do not allow children to swing empty rides or seats.
Do not allow children to go down slide head first or
run up slide.
2
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 6 feet from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
• NEVER allow children to play with ropes, clotheslines,
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
• NEVER allow children to wear loose tting clothing,
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
• NEVER allow children to wear bike or sport helmets
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose-fill
surfacing materials washing away during heavy rains.
DO NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
WARNING
WARNING – Safe Play Instructions

 3 [email protected]
 3 [email protected]

 4 [email protected]

 5 [email protected]
 5 [email protected]

 6 [email protected]
Square
Assembly

 7 [email protected]
1 inch = 25.4mm
SOLO)WAVE DESIGN HARDWARE
For example:
BOLT LENGTH 4½ (4.5) inches long
114mm long
1 inch = 25.4mm
25.4mm
4.5 inches x
DIAMETER CONVERSION
LENGTH CONVERSION
=
BOLT DIAMETER 5/16 (0.31) inches 0.31 inches x 25.4mm = 8mm
For example:
HARDWARE LENGTH CHART
inches vs millimetres
6 152
5½ 140
5 127
4½ 114
4 102
3½ 89
3 76
2½ 64
2 51
1½ 38 1¼ 32
1-1/8 29
1 25.4
7/8 22 3/4 19 1/2 12.7
1/4" (6mm) Flat Washer
1/4" (6mm) Lock Washer
1/4"(0.25) = 6mm Hex Bolt
1/4" (6mm) T-Nut
5/16"(.31) = 8mm Lag Screw
5/16" (8mm) Flat Washer
1/4"(0.25) = 6mm Lag Screw
1/4" (6mm) Flat Washer
5/16" (8mm) Flat Washer
5/16" (8mm) Lock Washer
5/16"(.31) = 8mm Hex Bolt
5/16" (8mm) T-Nut
3/8"(.38) = 9.5mm Lag Screw
3/8" (9.5mm) Flat Washer

 8 [email protected]
1 x 2 1 x 4 1 x 5
1 x 6
1 x 3
1/2 x 4
5/4 x 6
5 1/2"
139.7
1"
25.4
11.1
.44
82.6
3 1/4"
4 x 4
3 1/2"
88.9
3 1/2"
88.9
4 1/2"
114.3
5/8"
15.9
15.9
5/8" 1 3/8"
34.9
2 x 6
5 3/8"
136.5
1 1/2"
38.1
15.9
5/8" 3 3/8"
85.7
60.3
2 3/8"
15.9
5/8"
1505mm
SOLO)WAVE DESIGN WOOD PROFILES
LENGTH CONVERSION
For example:
1 inch = 25.4mm
BOARD LENGTH 59¼ (59.25) inches 59.25 inches x 25.4mm =
Dimensions in brackets [mm] represent millimetres.
5/4 x 4
3 1/2"
88.9
1"
25.4
5 3/8"
136.5
5/8"
15.9
2 x 4
3 3/8"
85.7
1 3/8"
34.9
5/4 x 5
4 1/2"
114.3
1"
25.4 2 x 3
2 1/2"
63.5
1 3/8"
34.9
5/4 x 3
63.5
2 1/2"
25.4
1"
2 x 2
1 1/2"
38.1
1 1/2"
38.1

 9 [email protected]
26pc. - 0517 Cedar Roofing (3/8 x 3-1/2 x 48") - Box 1 - 3630517
5pc. - 1801 Cedar Siding (3/8 x 3-1/2 x 46-5/8") - Box 2 - 3631801
18pc. - 1852 CE Siding (3/8 x 3-1/2 x 36") - Box 2 - 3631852
12pc. - 1800 CE Siding (3/8 x 3-1/2 x 25-1/2") - Box 1 - 3631800
25pc. - 1503 Wall Board (1/2 x 4 x 20") - Box 1 - 3631503
Part Identification (Reduced Part Size)
Nominal Size
1" x 2"
1" x 4"
1" x 5"
1" x 6"
Actual Size
⅝" x 1⅜"
⅝" x 3⅜"
⅝" x 4½"
⅝" x 5⅜"
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
1pc. - 1809 Door Trim (1 x 2 x 36-1/2") - Box 2 - 3641809
2pc. - 1956 Front Wall (1 x 4 x 25") - Box 1 - 3641956
2pc. - 1957 SL Roof Side (1 x 4 x 13-3/4") - Box 1 - 3641957
1pc. - 1876 Window Cross (1 x 2-1/2 x 28") - Box 2 - 3641876
2pc. - 1964 SW Wall Trim (1 x 2-1/2 x 40-3/8") - Box 2 - 3641964
2pc. - 1971 Window Upright (1 x 2-1/2 x 46") - Box 2 - 3641971
1pc. - 1806 Door Top (1 x 4 x 21") - Box 2 - 3641806
2pc. - 1858 Short Wall Support (1 x 4 x 24-1/4") - Box 2 - 3641858
1pc. - 1808 Short Trim (1 x 2 x 19-5/8") - Box 2 - 3641808
6pc. - 0318 Ground Stake (1-1/4 x 1-1/2 x 14") - Box 1 - 3650318
1pc. - 1870 Trim Short (1 x 2-1/2 x 19-5/8") - Box 2 - 3641870
1pc. - 1969 Seat Rail (1 x 4 x 28-3/8") - Box 2 - 3641969
2pc. - 1962 Post Couple (1 x 4 x 17-1/2") - Box 1 - 3641962

 10 [email protected]
1pc. - 1988 Gusset Ground Support (1 x 5 x 15-5/8") - Box 3 - 3641988
9pc. - 1851 Cedar Floor Board (1 x 5 x 38-3/4") - (8X)Box 1 & (1X)Box 2- 3631851
2pc. - 1501 Floor End (1 x 5 x 38-1/4") - Box 1 - 3641501
1pc. - 0348 SL Ground (1 x 5 x 38-1/4") - Box 1 - 3640348
2pc. - 1973 Crowsnest Floor (1 x 5 x 30") - Box 3 - 3631973
2pc. - 1970 Seat Bottom (1 x 5 x 11-1/2") - Box 2 - 3641970
1pc. - 1865 Sw Roof Side (1 x 4 x 59-1/2") - Box 1 - 3641865
Nominal Size
1" x 6"
1½" x 1½"
1⅜" x 2½"
Part Identification (Reduced Part Size)
2" x 3"
2" x 2"
5/4" x 4"
Part Identification (Reduced Part Size)
Actual Size
⅝" x 5⅜"
1" x 3¼"
Part Identification (Reduced Part Size)
2pc. - 0357 Tarp Front Back (1 x 4 x 47-3/4") - Box 1 - 3640357
1pc. - 0358 Top Front Back (1 x 4 x 46-1/2") - Box 1 - 3640358
4pc. - 1814 Wall Support (1 x 4 x 45-1/2") - Box 2 - 3641814
1pc. - 0839 CE Gap Board (1 x 4 x 38-3/4") - Box 1 - 3630839
1pc. - 1502 Wall Support (1 x 4 x 38-1/4") - Box 1 - 3641502
1pc. - 1955 Divider (1 x 4 x 35-3/16") - Box 1 - 3641955
1pc. - 1958 Back Divider (1 x 4 x 31-3/4") - Box 1 - 3641958
4pc. - 1975 Cedar Wall (1 x 4 x 29") - Box 3 - 3631975

 11 [email protected]
1pc. - 1974 Crowsnest Gap (1 x 6 x 30") - Box 3 - 3631974
2pc. - 0631 CE Rock Board (1 x 6 x 19-3/4") - Box 1 - 3630631
3pc. - 0630 CE Rock Board (1 x 6 x 19-3/4") - Box 1 - 3630630
2pc. - 0606 CE Access Board (1 x 6 x 19-3/4") () - Box 1 - 3630606
2pc. - 1972 Wall Board (1 x 6 x 15") - Box 2 - 3631972
4pc. - 0514 Roof Brace (1 x 6 x 13") - Box 1 - 3640514
1pc. - 1554 SW Ground (1 x 5 x 77") - Box 1 - 3641554
2pc. - 0351 Front Back (1 x 5 x 46-5/8") - Box 1 - 3640351
2pc. - 1505 Front Top (1 x 5 x 46-1/2") - Box 1 - 3641505
Part Identification (Reduced Part Size)
Nominal Size
1" x 6"
5/4" x 4"
2" x 2"
2" x 3"
Actual Size
⅝" x 5⅜"
1" x 3¼"
1½" x 1½"
1⅜" x 2½"
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
1pc. - 1867 Top Side (1 x 6 x 38-1/4") - Box 2 - 3641867
2pc. - 1978 Crowsnest Upright (5/4 x 2-3/4 x 32-5/8") - Box 3 - 3641978
2pc. - 1853 Cedar Gap Board (1 x 5 x 38-3/4") - Box 1- 3631853
1pc. - 1953 Back Floor (1 x 6 x 46-3/4") - Box 1 - 3641953

 12 [email protected]
2pc. - 1989 Crowsnest Side (5/4 x 3 x 14-7/8") - Box 3 - 3641989
1pc. - 1448 Crowsnest Short (5/4 x 3 x 25-1/4") - Box 3 - 3641448
1pc. - 1983 Crowsnest Back (5/4 x 3 x 30") - Box 3 - 3641983
2pc. - 1959 SL Wall Board (5/4 x 4 x 38") - Box 1 - 3641959
1pc. - 0790 Floor Joist (5/4 x 4 x 46-1/2") - Box 1 - 3640790
1pc. - 1862 SW Support (5/4 x 4 x 46-12") - Box 1 - 3641862
1pc. - 1817 Wall Top (5/4 x 4 x 46-5/8") - Box 2 - 3641817
1pc. - 0799 Floor Back (5/4 x 4 x 41-3/4") - Box 1 - 3640799
1pc. - 1966 Table Top (5/4 x 5 x 43-7/8") - Box 2 - 3641966
Part Identification (Reduced Part Size)
Nominal Size
1" x 6"
5/4" x 4"
2" x 2"
2" x 3"
Actual Size
⅝" x 5⅜"
1" x 3¼"
1½" x 1½"
1⅜" x 2½"
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
2pc. - 1984 Crowsnest Face (2 x 2-3/4 x 27-5/8") - Box 3 - 3641984
2pc. - 1982 Crowsnest Bottom Side (5/4 x 6 x 14-7/8") - Box 3 - 3641982
2pc. - 1981 Crowsnest Joist (5/4 x 3 x 12-1/2") - Box 3 - 3641981
2pc. - 1954 Gusset (2 x 3 x 12") - Box 1 - 3641954
2pc. - 0795 Side Joist (2 x 2 x 43") - Box 1 - 3640795
1pc. - 1967 Seat (5/4 x 6 x 39") - Box 2 - 3641967
2pc. - 0367 Floor Gusset (2 x 3 x 11") - Box 1 - 3640367
2pc. - 0501 Joist (2 x 2 x 43 1/2") - Box 1 - 3640501

 13 [email protected]
1pc. - 1979 Roof Support (2 x 3 x 36") - Box 3 - 3641979
2pc. - 1961 Post Roof Block (2 x 4 x 4-11/16") - Box 1 - 3641961
1pc. - 0369 Lower Diagonal (2 x 3 x 37") - Box 1 - 3640369
1pc. - 1977 Crowsnest SL Top (2 x 3 x 30") - Box 3 - 3641977
2pc. - 0349 Rock Rail (2 x 3 x 51") - Box 1 - 3640349
1pc. - 4919 SW Rail Block (2 x 4 x 5-3/8") - Box 1 - 3644919
2pc. - 1968 Seat Post (2 x 4 x 12-1/2") - Box 2 - 3641968
1pc. - 1861 SW Mount (2 x 4 x 38-1/8") - Box 1 - 3641861
1pc. - 1856 SW Upright (2 x 4 x 48-5/16") - Box 1 - 3641856
2pc. - 1500 Post (2 x 4 x 83") - Box 1 - 3641500
2pc. - 1863 SW Post (2 x 4 x 86-11/16") - Box 1 - 3641863
2pc. - 1980 Crowsnest Joist (2 x 3 x 12-1/2") - Box 3 - 3641980
1pc. - 1976 Crowsnest Front (2 x 3 x 30") - Box 3 - 3641976
1pc. - 1986 Crowsnest Diagonal (2 x 3 x 18-3/4") - Box 3 - 3641986
1pc. - 1951 Roof Support - Right (2 x 3 x 43-1/2") - Box 1 - 3641951
1pc. - 1950 Roof Support - Left (2 x 3 x 43-1/2") - Box 1 - 3641950
2pc. - 0863 Roof Support (2 x 3 x 43-1/2") - Box 1 - 3640863
Part Identification (Reduced Part Size)
1" x 6"
Nominal Size
Part Identification (Reduced Part Size)
1½" x 1½"
2" x 3"
2" x 2"
5/4" x 4"
1⅜" x 2½"
Actual Size
⅝" x 5⅜"
1" x 3¼"
Part Identification (Reduced Part Size)

 14 [email protected]
1pc. - 1825 Back Beam (2 x 6 x 83-5/8") - Box 1 - 3631825
2pc. - 1985 Crowsnest Gusset (2 x 6 x 13-5/8") - Box 1 - 3641985
2pc. - 1952 Long Post (2 x 4 x 92-3/8") - Box 1 - 3641952
2pc. - 0620 SL Brace (2 x 2 x 12-1/2") - Box 1 - 3640620
2pc. - 1960 Wall Brace (5/4 x 4 x 8-3/4") - Box 1 - 3641960
1pc. - 1450 SL Support (2 x 4 x 26-1/4") - Box 3 - 3641450
1pc. - 1987 SL Ground Support (1 x 5 x 33") - Box 3 - 3641987
Extra Boards NOT USED for this fort assembly
1pc. - 1826 Front Beam (2 x 6 x 83-5/8") - Box 1 - 3631826
1½" x 5⅜"
1⅜" x 3⅜"
Part Identification (Reduced Part Size)
2" x 4"
2" x 6"
Part Identification (Reduced Part Size)
Nominal Size Actual Size
Part Identification (Reduced Part Size)

 15 [email protected]
1pc. H8 - Hex Bolt 1/4 x 4-1/4" - (9277241)
6pc. H3 - Hex Bolt 1/4 x 2-1/2" - (9277222)
2pc. H4 - Hex Bolt 1/4 x 4" - (9277240)
4pc. LS1 - Lag Screw 1/4 x 1-1/2" - (9262212) 7pc. LS3 - Lag Screw 1/4 x 3" - (9262230)
1pc. H1 - Hex Bolt 1/4 x 1-1/2" - (9277212)
5pc. G4 - Hex Bolt 5/16 x 4" - (9277340)
2pc. G8 - Hex Bolt 5/16 x 2" - (9277320)
5pc. G5 - Hex Bolt 5/16 x 4-1/2" - (9277342)
Hardware Identification (Actual Size)
4pc. H7 - Hex Bolt 1/4 x 5-1/2" - (9277252)
2pc. G7 - Hex Bolt 5/16 x 5-1/2" - (9277352)
4pc. G1 - Hex Bolt 5/16 x 1-1/2" - (9277312)
6pc. H5 - Hex Bolt 1/4 x 4-1/2" - (9277242)
2pc. H11 - Hex Bolt 1/4 x 2-3/4" - (9277223)
2pc. H13 - Hex Bolt 1/4 x 3-1/2" - (9277232)
23pc. H2 - Hex Bolt 1/4 x 2" - (9277220)

 16 [email protected]
Hardware Identification (Actual Size)
43pc. S7 - Pan Screw #12 x 2" - (9264620)
37pc. S3 - Wood Screw #8 x 2-1/2" - (9290522)
30pc. S4 - Wood Screw #8 x 3" - (9290530)
2pc. S6 - Pan Screw #12 x 1" - (9264610)
14pc. TN2 - 5/16" T- Nut - (9285300)
21pc. S15 - Wood Screw #8 x 1-3/4" - (9260513)
5pc. S10 - Pan Screw #8 x 1" - (9264510)
41pc. S5 - Pan Screw #8 x 1/2" - (9264504)
68pc. S1 - Wood Screw #8 x 1-1/8" - (9290514)
174pc. S2 - Wood Screw #8 x 1-1/2" - (9260512)
12pc. PB2 - Pan Bolt 1/4 x 1-1/4" - (9274211)
14pc. LW2 - 5/16" Lock Washer - (9253300)
4pc. LN2 - 5/16" Lock Nut - (9283300)
5pc. BN1 - 1/4" Barrel Nut - (9248200)
53pc. TN1 - 1/4" T - Nut -(9285200)
58pc. LW1 - 1/4" Lock Washer - (9253200)
21pc. FW2 - 5/16" Flat Washer - (9251300)
306pc. S0 - Truss Screw #8 x 7/8" - (9229505)
64pc. FW1 - 1/4" Flat Washer - (9251200)
16pc. S8 - Pan Screw #12 x 3/4" - (9264603)
39pc. FW0 - 3/16" Flat Washer - (9251100)
18pc. FW3 - #8 Flat Washer - (9251500)

 17 [email protected]
1x - 10' Blowmold Slide
(3318110)
1X 3320386 Rocks (5pk)
3-Green 2-Yellow
1X 9320357
Cedar Summit
I.D. Plaque
1X 3200184
Triangle Plate (4pk)
Green
2X 3724943
42" Belt Swing Yellow
w.welded chain
1X 3724908
24" Acro Swing
Yellow
w.welded chain
1X 9750150
Cafe Canopy
1X 9200156
46" Cafe Frame
1X 3750150
Grandview Canopy Set
1X 3200166 (6pk)
Corner Brace Set
1X 3202001
Swing Hanger Bolt
Thru. (6 pk)
1X 3320401
Flower Box Set
Green
2X 3320121
Peak Detail
Green
Part Identification (Reduced Part Size)
1X 3200164 (4pk)
Corner Brace Set

 18 [email protected]
1-877-966-3738
[email protected]
B.Ifthereareanymissingordamagedpiecesoryouneedassistancewith
assemblypleasecontacttheConsumerRelationsDepartmentdirectly.Callus
beforegoingbacktothestore.
STOP STOPSTOP STOP
Step 1: Inventory Parts - Read This Before Starting Assembly
C. Readtheassemblymanualcompletely,payingspecialattentiontoANSIwarnings;
notes;andsafety/maintenanceinformationonpages1-6.
D. Beforeyoudiscardyourcartonsllouttheformbelow.

•ThecartonI.D.stampislocatedontheendofeachcarton.Thetrackingnumberis
locatedontheBigBackyardIDPlaque(3320356).
 •Pleaseretainthisinformationforfuturereference.Youwillneedthisinformationifyou
contacttheConsumerRelationsDepartment.
•PleaserefertoPage6forproperhardwareassembly.

•Eachstepindicateswhichboltsand/orscrewsyouwillneedforassembly,aswellas
anyatwashers,lockwashers,t-nutsorlocknuts.
A.Thisisthetimeforyoutoinventoryallyourhardware,woodandaccessories,
referencingthepartsidenticationsheets.Thiswillassistyouwithyourassembly.

•Thewoodpieceswillhavethefourdigitkeynumberstampedontheendsofthe
boards.Thewoodpiecesarereferencedthroughouttheinstructionswiththisnumber.
CARTONI.D.STAMP:__________14459___(Box4)
CARTONI.D.STAMP:__________14459___(Box5)
CARTONI.D.STAMP:__________14459___(Box6)
CARTONI.D.STAMP:__________14459___(Box1)
CARTONI.D.STAMP:__________14459___(Box2)
CARTONI.D.STAMP:__________14459___(Box3)
MODELNUMBER:F24720
TRACKINGNUMBER(fromIDPlaque):

 19 [email protected]
Wood Parts Hardware Other Parts
Step 2: Rock Wall Assembly
A:Lay2(0349)RockRailsdown,sidebysidewithanglededgesfacingdown.(g.2.1)
B:Place(0606)CEAccessBoardonthebottomofeach(0349)RockRailasshowning.2.1.Makesure(0606)
CEAccessBoardisushtotheoutsideandbottomedgesofeach(0349).Attachusing4(S2)#8x1-1/2”Wood
Screws.
C:7-3/4”downfromthetopofboth(0349)RockRailsplace1(0630)CERockBoard,makingsurethesidesare
ushtotheoutsideedgesofeach(0349)RockRail.Attachusing4(S2)#8x1-1/2”WoodScrews.(g.2.1)
D:Inbetweenthe(0606)CEAccessBoardand(0630)CERockBoardstagger2(0630)and2(0631)CERock
Boardsusing4(S2)#8x1-1/2”WoodScrewsperboard.Placingthemasshowning.2.1,thiswillpreventrocks
fromformingastraightline.Makesuretheboardsareevenlyspacedanddonotexceed2-3/8”betweenboards.
E: Place1rockoneach(0630)and(0631)
CERockBoard(g.2.2)andattachusing1
(PB2)1/4x1-1/4”PanBolt(withlockwasher,
atwasherandbarrelnut)and1(S10)#8x
1”PanScrewperrock.TheScrewmustbein
theholedirectlyunderthePanBolt,itwillstop
therockfromspinning.(g.2.3)
Note: Gaps between boards 2-1/4”,
not to exceed 2-3/8”
Note: The holes
in the rock boards
must orient to the
top of the boards.
7-3/4”
Approx
Fig. 2.1
S2 0606 0349
0631
0630 0630 0630
0631
Fig. 2.2
Fig. 2.3
1 x CE Access Board 1 x 6 x 19-3/4”
3 x CE Rock Board 1 x 6 x 19-3/4”
2 x CE Rock Board 1 x 6 x 19-3/4”
2 x Rock Rail 2 x 3 x 51”
24 x #8 x 1-1/2” Wood Screw
5 x #8 x 1” Pan Screw
5 x 1/4 x 1-1/4 Pan Bolt
(1/4” lock washer, 3/16” at washer & 1/4” barrel nut)
S2
0349
0631
0630
0606
3/16”Flat
Washer
1/4”Lock
Washer
1/4”Barrel
Nut
Rock
5 x Rocks (3 green/2 yellow)
S10
S10
PB2
PB2

 20 [email protected]
xx x
x
x
x x x
Step 3: Swing Beam Assembly
Make sure triangle is
tight against beam
Warning: For your child’s safety,
orientate the swing hangers as
shown to ensure your swing will
have proper swing motion when
installed. Failure to do so could
result in premature failure of the
swing hanger or swing chain.
A:Inthemiddleholesof(1825)BackBeaminstall2Bolt-Thru
SwingHangers(g.3.1)makingsuretheswinghangersare
orientedinthedirectionshowning.3.4tomaintainproper
swingmotion.Intheendholesinstall2(G7)5/16x5-1/2”Hex
Bolt(with2atwashers&locknut)asshowning.3.1
B:Intheendholesof(1826)FrontBeam
install4Bolt-ThruSwingHangers(g.3.1)
makingsuretheswinghangersareoriented
inthedirectionshowning.3.4tomaintain
properswingmotion.
Fig. 3.4
C: Attach1TrianglePlate
totheendsofeach(1826)
FrontBeamand(1825)Back
Beamusing1(G1)5/16x
1-1/2”HexBolt(withlock
washer,atwasherand
t-nut)intheholeindicatedin
g.3.2&3.3.Correct hole
usage is very important.
Important!
Swing End
(With Overhang)
Important!
Fort End Side
(No Overhang)
D:Attach1(H7)1/4x5-1/2”HexBolt(withlockwasher,atwasherandt-nut)totheendsofeach(1826)Front
Beamand(1825)BackBeam.Theboltsdonotattachtoanything,butMUSTbeinstalledtothebeamstoprevent
splittingandcheckingofwood.(g.3.2&3.3)
Swing End
(With Overhang) Fort End Side
(No Overhang)
Wood Parts Hardware
Bolt-Thru
SwingHangers
4 x 1/4 x 5-1/2” Hex Bolt
(1/4” at washer, 1/4” lock washer, 1/4” t-nut)
4 x 5/16 x 1-1/2” Hex Bolt
(5/16” at washer, 5/16” lock washer, 5/16” t-nut)
2 x 5/16 x 5-1/2” Hex Bolt
(5/16” at washer x 2, 5/16” lock nut)
H7
G1
1 x Bolt-Thru Swing Hangers (pkg of 6)
1 x Triangle Plate (pkg of 4)
1 x Front Beam 2 x 6 x 83-5/8”
1 x Back Beam 2 x 6 x 83-5/8”
1826
1825
Triangle
Plates
G1 H7
1826
1825
1/4”Flat
Washer 1/4”Lock
Washer
1/4”
T-Nut
5/16”Flat
Washer
5/16”Lock
Washer
5/16”
T-Nut
1826
1825
H7
Other Parts
Fig. 3.2
Fig. 3.3
G1
H7
G1 G1
H7
Fig. 3.1
Bolt-Thru
SwingHangers
TrianglePlates
G7
G7
5/16”Flat
Washer
5/16”lock
nut