Cedar Summit F25650 User manual

INSTALLATION AND OPERATING INSTRUCTIONS
MOUNT FOREST LODGE – F25650
To reduce the risk of serious injury or death, you must
read and follow these instructions. Keep and refer to these
instructions often and give them to any future owner of this
play set. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE -28’6 x 28’ 2”(9.45 x 8.53 m) area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 7.1 ft. (2.16 m)
CAPACITY - 10 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries,
day cares or parks.
Rev 11/27/20133405650
Table of Contents
Warnings and Safe Play Instructions . . . . . . . . . . .pg. 2
Protective Surfacing Guidelines................pg.3
Instructions for Proper Maintenance ...........pg.4
About Our Wood – Limited Warranty. . . . . . . . . . .pg. 5
Keys to Assembly Success .....................pg.6
Part ID.........................................pg.7
Step-By-Step Instructions.................... pg.17
Installation of I.D./Warning Plaque . . . . . . . .Final Step
Cedar Summit
c/o ©Solowave Design L.P.
Mount Forest, ON Canada
N0G 2L0
www.cedarsummitplay.com
[e-mail]
Customer Service
1-877-817-5682 (toll free)
1-519-323-2258
16'-2"
28'-6"
28'-2"
13'-7"
MOUNT FOREST LODGE
TWO PERSON
ASSEMBLY
10 - 12 Hrs
FOR FORT & SWING
WARNING

Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
Observe capacity limitations of your play-set. See
front cover.
Dress children with well fitting and full foot enclosing
footwear.
Teach children to sit with their full weight in the center
of the swing seat to prevent erratic swing motion or
falling off.
Check for splintered, broken or cracked wood; missing,
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
Verify that suspended climbing ropes, rope ladders, chain
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
On sunny and or hot days, check the slide and other
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
Do not allow children to wear open toe or heel footwear
like sandals, flip–flops or clogs.
Do not allow children to walk, in front, between, behind
or close to moving rides.
Do not let children twist swing chains or ropes or loop
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
Do not let children get off rides while they are in motion.
Do not permit climbing on equipment when it is wet.
Do not permit rough play or use of equipment in a
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
Do not allow children to swing empty rides or seats.
Do not allow children to go down slide head first or
run up slide.
2
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 6 feet from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
• NEVER allow children to play with ropes, clotheslines,
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
• NEVER allow children to wear loose tting clothing,
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
• NEVER allow children to wear bike or sport helmets
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose-fill
surfacing materials washing away during heavy rains.
DO NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
WARNING
WARNING – Safe Play Instructions
2 [e-mail]

One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing
protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable
for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever
product you select, follow these guidelines:
Loose-Fill Materials
• Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet
high. NOTE: An initial fill level of 12 inches will compress to about a 9-inch depth of surfacing over time. The surfacing will also
compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch depth.
• Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this
should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface
can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and
environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective
surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play
surface -- does not need any protective surfacing.
• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
• Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play
equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to
rake and evenly redistribute the surfacing in heavily used areas.
• Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-place surfaces.
• Installations of these surfaces generally require a professional and are not “do-it yourself” projects.
• Review surface specifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that
the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of
Surfacing Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the
surface is intended to protect against serious head injury. This height should be equal to or greater than the fall height - vertical
distance between a designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing
below - of your play equipment.
• Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;
• Extend surfacing at least 6 feet from the equipment in all directions.
• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top
bar from which the swing is suspended.
• For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all directions.
From the CPSC Outdoor Home Playground Safety Handbook. At www.cpsc.gov/CPSCPUB/PUBS/324.pdf
Protective Surfacing - Reducing Risk of Serious Head Injury From Falls.
3
2H 2H
H
Denotes Use Zone with Protective Surfacing
Use Zone for Single-Axis Swings
6 ft.
6 ft.
6 ft.
6 ft.
Denotes Use Zone with Protective Surfacing
Use Zone for Multi-Axis Swings
6 ft. 6 ft.
6 ft.
L
3 [e-mail]

Instructions for Proper Maintenance
Your Cedar Summit Play System is designed and constructed of quality materials with your child’s safety in mind. As with all
outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is
important that you, the owner, properly maintain it.
HARDWARE:
Check metal parts for rust. If found,
sand and repaint using a non-lead
paint complying with 16 CFR 1303.
Inspect and tighten all hardware. On
wood assemblies DO NOT OVER-
TIGHTEN as to cause crushing and
splintering of wood.
Check for sharp edges or protruding screw threads, add
washers if required.
SHOCK ABSORBING SURFACING:
Check for foreign objects. Rake and check depth of loose
fill protective surfacing materials to prevent compaction
and maintain appropriate depth. Replace as necessary.
(See Protective Surfacing, page 3)
GROUND STAKES (ANCHORS):
Check for looseness, damage or deterioration. Should
firmly anchor unit to ground during use. Re-secure and
or replace, if necessary.
SWING HANGERS:
Check that bolts are secure and tight. Quick clips should
be completely closed and threaded clips screwed tight.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS, ROPES AND RIDES:
Reinstall if removed during cold season. Check all
moving parts including swing seats, ropes, chains and
attachments for wear, rust and other deterioration.
Replace as needed.
Check that ropes are tight, secure at both ends and
cannot loop back as to create an entrapment.
WOOD PARTS:
Check all wood members for deterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
Unprotected, they will appear weathered over time.
Periodic application of an exterior water repellent or stain
(water-based) will help improve appearance and life.
Check the following at the beginning of the play season:
HARDWARE:
Inspect for tightness. Must be firmly against, but not
crushing the wood. DO NOT OVER-TIGHTEN.
This will cause splintering of wood.
Check for sharp edges or protruding screw threads.
Add washers if required.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check twice a month during play season:
SWING HANGERS:
Check that they are secure and orientated correctly. Hook
should rotate freely and perpendicular to support beam.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS AND RIDES:
Check swing seats, all ropes, chains and attachments for
fraying, wear, excessive corrosion or damage.
Replace if structurally damaged or deteriorated.
Check once a month during play season:
SWINGS AND RIDES:
To prolong their life, remove swings and store inside
when outside temperature is below 32°F/0°C. Below
freezing, plastic parts may become more brittle.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check at the end of the play season:
If you dispose of your play set: Please disassemble and dispose of your unit so that it does not create any unreasonable hazards
at the time it is discarded. Be sure to follow your local waste ordinances.
4
Use an extra
Flat Washer
If Bolt protrudes
beyond T-Nut
4 [e-mail]

About Our Wood
Cedar Summit Premium Play Systems uses 100% FSC wood. Although we take great care in selecting the best quality lumber
available, wood is still a product of nature and susceptible to weathering which can change the appearance of your set.
What causes weathering? Does it affect the strength of my Play System?
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the surface is
different than the interior of the wood. As the climate changes, moisture moves in or out of the wood, causing tension which can
result in checking and or warping. You can expect the following due to weathering. These changes will not affect the strength of
the product:
1. Checking is surface cracks in the wood along the grain. A post (4” x 4”) will experience more checking than a board (1” x 4”)
because the surface and interior moisture content will vary more widely than in thinner wood.
2. Warping results from any distortion (twisting, cupping) from the original plane of the board and often happens from rapid
wetting and drying of the wood.
3. Fading happens as a natural change in the wood color as it is exposed to sun-light and will turn a grey over time.
How can I reduce the amount of weathering to my Play System?
At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water absorption
during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, so we recommend applying a
water repellent or stain on a yearly basis (see your local stain and paint supplier for a recommended product).
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are
concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.
Complete and mail registration card to receive important product notifications and assure prompt
warranty service.
10 Year Limited Warranty
Solowave Design warrants that this product is free from defect in materials and workmanship for a
period of one year from the original date of purchase. In addition, lumber is warranted for 10 years
against structural failure due to rot and insect damage. All other parts, such as hardware, swings, rides,
accessories, and slides carry a one-year warranty only.
This warranty applies to the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your Play System. This warranty does not
cover any inspection cost.
This Limited Warranty does not cover:
• Labor for replacement of any defective item(s);
• Incidental or consequential damages;
• Cosmetic defects which do not affect performance or integrity;
• Vandalism; improper use or installation; acts of nature;
•Minor twisting, warping, checking, or any other natural occurring properties of wood that do not
affect performance or integrity.
Solowave Design products have been designed for safety and quality. Any modifications made to
the original product could damage the structural integrity of the unit leading to failure and possible
injury. Solowave Design Inc. cannot assume any responsibility for modified products. Furthermore,
modification voids any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a
Solowave Design Play System be used in public settings such as schools, churches, playgrounds,
parks, day cares and the like. Such use may lead to product failure and potential injury. Any and all
public use will void this warranty.
Solowave Design disclaims all other representations and warranties of any kind, express or implied.
This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state or
province to province. This warranty excludes all consequential damages, however, some states do not allow the
limitation or exclusion of consequential damages, and therefore this limitation may not apply to you.
5
5 [e-mail]

and quantities required to complete
the assembly step illustrated on that
page. Here is a sample.
Key Number:
represent the step number. The third
digit represents the piece. Note that if
the part is used in multiple steps then
it is used in.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only a
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
then hole. Because the assemblies
need to be squared do not completely
tighten until instructed. Pay close
attention to diameter of the bolts.
5/16” is slightly larger than 1/4”.
Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.
Once the assembly is tightened, watch for exposed
threads. If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminate this condition.
Extra washers have been provided for this purpose.
special attention. Improper assembly could
lead to an unsafe or dangerous condition.
Where this is shown, 2 or 3
people are required to safely
complete the step. To avoid
injury or damage to the
assembly make sure to
get help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to
assure proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill 1/8” & 3/16” Bit
Tighten
Bolts
No Yes
CAUTION – Protrusion Hazard
6
Keys to Assembly Success
Tools Required
•Tape Measure
• Carpenters Level
• Carpenters Square
• Claw Hammer
•Standard or Cordless Drill
• #1 Philips, #2 Robertson,
and Screwdriver
• Ratchet with extension
(1/2” & 9/16” sockets)
• Open End Wrench
(1/2” & 9/16”)
•Adjustable Wrench
• 1/8” & 3/16” Drill Bits
• Pencil
• 3/16” Hex Key
• 8’ Step Ladder
• Safety Glasses
•Adult Helpers
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
Use an extra
Flat W asher
If Bolt protrudes
beyond T-Nut
Lag Screw
Flat Washer
Lag Assembly
Before mounting Lag Screw,
use factory drilled holes as
guides to drill 1/8” pilot holes
Hex Bolt Bolt Assembly
T-Nut
(Hammer into place)
Do not crush wood!
Lock
Washer
Flat
Washer
moc.yalptimmusradec@troppus
6 [e-mail]

Key Number: The rst two digits represent the step
number. The third digit represents the order in which
the part is listed in the step.
Note that if the part is used in multiple steps then
the key number only reects the rst step it is used in.
Part Quantity Key Number
Order Listed
(The order the part is
listed in step 1)
Part Description Part Size
2X 012 Post 2 x 4 x 83”
00
Your Key To Quick Assembly
SAVE TIME - TIP #1:
Wood parts are found in Box 2, 3, 4 & 5. Open each box with wood parts and
look for the Key Number stamped on the end of the wood part (see chart below).
Sort each wood part into the different assembly steps.
SAVE TIME - TIP #2:
In addition to the key number stamp, you can also identify the wood parts by
using the Parts Identication pages in the manual or the Parts Identication
weather resistant poster.
HARDWARE:
The majority of each hardware part comes packed in a separate bag so
you do not need to sort the hardware. Each assembly step indicates which
hardware (bolt, screw, washer etc.) you will require to complete the step.
SORTING WOOD PARTS INTO
EACH ASSEMBLY STEP WILL
SAVE TIME!
Step Step Step
01 2
Step Number
(This is Step 1)
7 [e-mail]

Acro Bar
183
125
PARTSIDENTIFICATION
FRONT
051 SL Side
Window Panel
153
181
185
186
x4
187
182
270
Panel
SW Side043
120 025
x2
042
Sign
184
Clock
Chalk
Wall Panel
Spin
180
Chalk
x2
321
320
322
Wheel
x4
Steering
Telescope
040
Maze N
Wave Slide
Cafe
Wall Window
Panel
041
Corner
Panel
Bracket
x8
Seat x2
x2
Swing Belt
54" Chain
Heavy T
Bracket
080
Heavy L
Bracket x2
x4
25" Chain
126
Acro
Heavy G
Summit
ID Plaque
Handle
Cedar
Cedar Summit
Plaque
081
260
Bracket x2
272
112
280
Re-Bar Ground
Stake x6
271
127
220 Transom Front
123
082
x2
x2
121
122
Hidden
Heavy Duty
Swing Hanger x6
8 [e-mail]

Window Panel
Door Wall061
Window Panel
Door
Bench Set
3 in 1
090
REAR
PARTSIDENTIFICATION
Wall Window Panel
Half Narrow060
2
Window Panel X
Narrow050
2
Roof Panel X
Small211
2
Roof Panel X
Large210
044 100 110 111
065
063
020 021
x4
023
030
032
032
032
035
035
034
034
033
033
033
022
031
x3
151
x3
150
140
062
064
x5
Bracket Flat Panel
370
x9
152
124
x2
Back
Transom221
x2
Grip
x10
Rocks
Door Hardware CS Panorama
Steel Hand
x2
126
x2
162
x2
163
161
092
164
x8
166
192
165
191
190
160
Hidden
024
Rail
EN71 Hand
200
093
013
x2
x4
010
x2
012
011
x2
x2
014
091
Swing
Brackets x3
Corner
Bracket x6
9 [e-mail]

Nominal Size
1" x 4"
1" x 5"
1" x 6"
Actual Size
⅝" x 3¼"
⅝" x 4¼"
⅝" x 5¼"
Part Identification (Reduced Part Size)
4pc. -041 - Window Shutter FSC ⅝x 3 x 15" - Box 2 - 4608778
2pc. -186 - Centre Gable FSC 1 x 4 x 13½" - Box 2 - 4638820
8pc. -166 - Wall Board FSC 1 x 4 x 26½" - Box 4 - 4638039
1pc. -093 - Door Bottom FSC 1 x 4 x 33½" - Box 2 - 4638821
1pc. -023 - Ladder Gap FSC 1 x 4 x 15" - Box 2 - 4638828
1pc. -030 - Board Access FSC 1 x 4 x 20½" - Box 4 - 4638826
1pc. -321 - Roof Board A FSC 1 x 5 x 22⅝" - Box 3 - 4638803
1pc. -322 - Roof Board B FSC 1 x 5 x 23¼" - Box 3 - 4638804
1pc. -164 - Centre Wall Board FSC 1 x 5 x 32" - Box 5 - 4638608
1pc. -153 - Floor A FSC 1 x 5 x 36" - Box 2 - 4638796
3pc. -151 - Slidenest Floor A FSC 1 x 5 x 42½" - Box 4 - 4638795
1pc. -031 - Rock Bottom FSC 1 x 6 x 20½" - Box 3 - 4638827
3pc. -032 - Rock Board A FSC 1 x 6 x 20½" - Box 5 - 4638822
4pc. -187 - Side Gable FSC 1 x 4 x 8½" - Box 2 - 4638819
3pc. -033 - Rock Board B FSC 1 x 6 x 20½" - Box 5 - 4638823
10 [e-mail]

2pc. -034 - Rock Board C FSC 1 x 6 x 20½" - Box 5 - 4638824
2pc. -012 - Box Ground FSC 5/4 x 4 x 29" - Box 2 - 4638830
1pc. -190 - Right Gable Angle FSC 5/4 x 4 x 31"
Box 4 - 4638817
Part Identification (Reduced Part Size)
Actual Size
⅝" x 5¼"
15/16" x 2¼"
15/16" x 3¼"
Nominal Size
1" x 6"
5/4" x 3"
5/4 x 4"
1pc. -025 - Top Ladder FSC 5/4 x 3 x 34¼" - Box 2 - 4638829
4pc. -022 - Ladder Tread FSC 5/4 x 4 x 13¾" - Box 3 - 4638517
9pc. -152 - Floor FSC 1 x 6 x 36" - Box 2 - 4638797
3pc. -150 - Slidenest Floor FSC 1 x 6 x 42½" - Box 4- 4638794
1pc. -112 - SW Table Top FSC 5/4 x 3 x 31¾" - Box 3 - 4638811
2pc. -014 - Box Gusset FSC 5/4 x 4 x 8½" - Box 3 - 4638834
1pc. -091 - Door Stop FSC 5/4 x 4 x 10" - Box 4 - 4638625
4pc. -010 - Box Leg FSC 5/4 x 4 x 16" - Box 4 - 4638831
2pc. -011 - Box End FSC 5/4 x 4 x 14¼" - Box 3 - 4638832
1pc. -181 - Roof Support Left FSC 5/4 x 4 x 29"- Box 4 - 4638807
1pc. -180 - Roof Support FSC 5/4 x 4 x 29" - Box 4 - 4638806
2pc. -035 - Rock Board D FSC 1 x 6 x 20½" - Box 5 - 4638825
1pc. -191 - Left Gable Angle FSC 5/4 x 4 x 31"
Box 4 - 4638818
2pc. -122 - Post FSC 5/4 x 4 x 31⅞" - Box 3 - 4638791
11 [e-mail]

Part Identification (Reduced Part Size)
Actual Size
15/16" x 3¼"
15/16" x 4¼"
15/16" x 5¼"
Nominal Size
5/4" x 4"
5/4" x 5"
5/4" x 6"
2pc. -013 - Box Side FSC 5/4 x 4 x 32" - Box 3 - 4638833
1pc. -127 - Front Top FSC 5/4 x 4 x 65½" - Box 3 - 4638798
1pc. -100 - Back Top FSC 5/4 x 4 x 65½" - Box 3 - 4638799
1pc. -065 - Back Ground FSC 5/4 x 4 x 79¾" - Box 3 - 4638780
1pc. -063 - Front Ground FSC 5/4 x 4 x 79¾" - Box 3 - 4638776
1pc. -110 - Ground SW FSC 5/4 x 4 x 82⅝" - Box 3 - 4638782
1pc. -123 - SL Top Right FSC 5/4 x 5 x 6½" - Box 4 - 4638788
1pc. -120 - SL Top Left FSC 5/4 x 5 x 9¾" - Box 3 - 4638787
1pc. -165 - Steering Wheel Dash FSC 5/4 x 5 x 12⅛" - Box 4 - 4638609
2pc. -162 - Crowsnest Side FSC 5/4 x 5 x 16¾" - Box 4 - 4638815
1pc. -125 - SL Top FSC 5/4 x 5 x 30⅝" - Box 3- 4638793
1pc. -080 - Table Top FSC 5/4 x 5 x 35½" - Box 3- 4638801
1pc. -160 - Crowsnest Top FSC 5/4 x 5 x 37⅞" - Box 2 - 4638813
2pc. -185 - Sunburst FSC 5/4 x 6 x 10" - Box 2 - 4638614
1pc. -370 - Middle Arch FSC 5/4 x 5 x 36¼" - Box 3 - 4638800
12 [e-mail]

124 - Short Floor Joist FSC 2 x 4 x 5¼" - Box 4 - 4638623 1pc. -
- Small Roof Support FSC 2 x 2 x 22½" - Box 2 - 4638802
320
-
2pc.
2pc. -121 - Short Joist FSC 2 x 4 x 5¼" - Box 4 - 4638789
2pc. -
Part Identification (Reduced Part Size)
111 - Diagonal FSC 2 x 3 x 42¼" - Box 3 - 4638587
1¼" x 3¼"
1¼" x 2¼"
1¼" x 2⅛"
1½" x 1½"
1¼" x 1¼"
15/16" x 5¼"
Actual Size
1¼" x 1¼"
5/4" x 6"
2" x 4"
2" x 3"
1¼" x 2⅛"
1½" x 1½"
Nominal Size
- Roof Spacer FSC 5/4 x 6 x 32¼" - Box 4- 4638777
200
-
2pc.
- Floor End FSC 5/4 x 6 x 38½" - Box 2 - 4638786
092
-
1pc.
- SL Post FSC 1¼ x 1¼ x 44⅞" - Box 3 - 4638790
082
-
1pc.
- Top Post Right FSC 1¼ x 2⅛x 24⅝" - Box 4 - 4638809
182
-
1pc.
- Top Post Left FSC 1¼ x 2⅛x 24⅝" - Box 4 - 4638808
183
-
1pc.
- Table Gusset FSC 2 x 3 x 3" - Box 2 - 4638805
081
-
2pc.
- Crowsnest Post FSC 2 x 3 x 28" - Box 3 - 4638812
161
-
2pc.
- Crowsnest Bottom FSC 2 x 4 x 16¾" - Box 4 - 4638814
163
-
2pc.
- SL End FSC 2 x 4 x 28¾" - Box 3 - 4638792
126
-
1pc.
- Gable Bottom FSC 2 x 4 x 34½" - Box 3 - 4638816
192
-
1pc.
- Left Access Rail FSC 2 x 4 x 62⅞" - Box 4 - 4638145
020
-
1pc.
1pc. -021 - Right Access Rail FSC 2 x 4 x 62⅞" - Box 4 - 4638146
13 [e-mail]

1pc. -271 - Block SW FSC 2½ x 3 x 15" - Box 3 - 4638507
1pc. -
Part Identification (Reduced Part Size)
260
3 x 3
3" x 5¼"
1¼" x 5"
1¼" x 3¼"
Actual SizeNominal Size
- Engineered SW Beam FSC 3 x 5¼ x 110" - Box 2 - 4638509
4" x 4"
3" x 6"
2" x 5"
2" x 4"
- Support Cross FSC 2½ x 3 x 64" - Box 4 - 4638510
280
-
1pc.
- Rock Rail FSC 2 x 4 x 62⅞" - Box 4 - 4638139
024
-
1pc.
- Floor Joist FSC 2 x 4 x 81" - Box 4 - 4638783
140
-
1pc.
- Front Floor FSC 2 x 4 x 81" - Box 4 - 4638784
062
-
1pc.
- Back Floor FSC 2 x 4 x 81" - Box 3 - 4638785
064
-
1pc.
- SW Block Angle FSC 2½ x 3 x 15" - Box 3 - 4638508
270
-
1pc.
- SW Wall FSC 4 x 4 x 38½" - Box 3 - 4638779
044
-
1pc.
- SW Post FSC 4 x 4 x 105" - Box 3 - 4638166
272
-
2pc.
1pc. -184 - SW Top FSC 1¼ x 5 x 36" - Box 3 - 4638810
14 [e-mail]

1pc.-
Part Identification (Reduced Assembly Size)
-Transom Panel Front FSC
1¼ x 11½ x 35⅞" - Box 2 - 47638745
220
2pc.
-
Box 4 - 47638749
FSC 1¼ x 16¾ x 56"
Panel
Half Narrow Window 060
-
043
1¼ x 36 x 87¼" - Box 2 -47638775
FSC
SW Side Panel
-
-
1pc.
1pc.
-
Box 4 - 47638767
1¼ x 16¾ x 56"
FSC
Chalkwall Panel042
-
051
1¼ x 30 x 54⅛"- Box 3 - 47638713
FSC
SL Side Window Panel
-
-
1pc.
1pc.
-
Door Window
-
Box 2 - 47608835
1¼ x 16¾ x 44-7/16"
FSC Dark Brown
Panel
090
050
1¼ x 16¾ x 99" - Box 3 - 47638702
FSC
Narrow Window Panel
-
-
2pc.
061
1¼ x 36 x 54⅛" - Box 2 - 47638737
FSC
Door Wall Window Panel
-
-
1pc.
040
1¼ x 35½ x 99"- Box 2 - 47638730
FSC
Cafe Wall Window Panel
-
-
1pc.
210
1¼ x 31¾ x 41" - Box 4 - 47638756
FSC
Large Roof Panel
-
-
2pc.
211
1¼ x 31¾ x 32½" - Box 4 - 47638760
FSC
Small Roof Panel
-
1pc. -
1pc. -221 - Transom Panel Back FSC
1¼ x 11½ x 35⅞" - Box 2 - 47638742
15 [e-mail]

1x - EN71 Hand Rail
(9200223) -Yellow
1x - Telescope
(3320161)
1x. - Rocks (10pk)
(3320210) -Green/Yellow/Burgundy
1x - Spin Chalk Sign
(3320715)
2x 9200151 (L-Bracket)
1x 9200152(T-Bracket)
1x 9200150 (G-Bracket)
1x - Heavy Bracket Set
(3200150) Green
2x - Acro Handle
(9320131) Green
1x - (3pk) Swing Bracket Set
(3201530) -Green
1x - Heavy Duty Swing Hangers
with Clips (6pc set)
(3201950)
1x - (6pk) Rebar Ground Stake 16"
(3200318)
2x - Swing Belt Seat
(9320130) Green
2x - Steel Hand Grip
(9200211) -Yellow
1x -
1x -Seat
(9320123)
2x -Plug
(9320703)
1x -Shovel
(9320326)
1x - Cedar Summit ID Plaque
(9320357)
1x -Sand and Water Insert
(9320105)
1x -3 in 1 Bench Set (3320123)
1x Catch Plate
1x Magnetic Catch
Door Hinge -Green
2x 9201713
Door Catch -Brown
9207713
Door Handle -Green
2x 9207711
1x - C.S. Panorama Door Hardware
(3201710)
1x - Acro Bar
(9200130) Green
1x - Cedar Summit Plaque
(9320358)
1x - Steering Wheel
(3320255)
4x 9201254
54" chain -Green
- Welded Chain Bag
(3200170) Green
1x 2x 9201225
25" chain -Green
(6pk) 3206570
Corner Bracket
Part Identification (Reduced Part Size)
Flat Panel Brkt
(5pk) 3200635
(4pk) 3200629
(3201700)
- MFL Bracket Set
Corner Panel Brkt
1x
(4pk) 3200628
Corner Panel Brkt
Clock
Assembly (3320124)
16 [e-mail]

2pc. -G1 -Hex Bolt 5/16 x 1-1/2" - (53703312)
1pc. -D4 -#2 x 2" Robertson Driver Bit-
(9200014)
20pc. -WB9 -Wafer Bolt 5/16 x 2⅛"- (53613324)
15pc. -WL5 -Wafer Lag 1
4x 2½" - (52613222)
Hardware Identification (Actual Size)
-
G21 - (53703333)
-
4pc. Hex Bolt 5/16 x 3¾"
12pc. -G13 -Hex Bolt 5/16 x 6⅛"- (53703364)
12pc. -G8 -Hex Bolt 5/16 x 2" - (53703320)
5pc. -WL3 -Wafer Lag 1
4x 1⅜"- (52613216)
15pc. -WB2 -Wafer Bolt 5/16 x 1⅜"- (53613316)
18pc. -WB7 -Wafer Bolt 5/16 x 3" - (53613330)
10pc. -PB2 -Pan Bolt 1
4x 11 4- (53433212)
5pc. -LS9 -Lag Screw 5/16 x 4¾" - (52213343)
11pc. -WB8 -Wafer Bolt 5/16 x 2⅜"- (53613326)
17 [e-mail]

14pc. -S10 -Pan Screw #8 x 1" - (52433510)
55pc. -S15 -Wood Screw #8 x 1¾" - (52043513)
28pc. -S4 -Wood Screw #8 x 3" - (52043530)
76pc. -S3 -Wood Screw #8 x 2½" - (52043522)
Hardware Identification (Actual Size)
4pc. -WH2 -Wafer Head Screw #12 x 1" - (52613610)
44pc. -S13 -Pan Screw #6 x 5
8"- (52413908)
1pc. -G20 -Hex Bolt 3/8 x 4" - (53703840)
15pc. -S7 -Pan Screw #12 x 2" - (52433620)
**NOTE: Appoximately 2" removed from actual size**
1pc. -G26 -Hex Bolt 3/8 x 9¼" - (53703891)
8pc. -S18 -Wood Screw #6 x 1" - (52013910)
6pc. -S5 -Pan Screw #8 x ½" - (52433502)
4pc. -G17 -Hex Bolt 3/8 x 6" - (53703860)
- (53703890)
1pc. -G18 -Hex Bolt 3/8 x 9"
**NOTE: Appoximately 2" removed from actual size**
12pc. -TS -Trim Screw #6 x 30mm - (52953911)
234pc. -S20 - Wood Screw #8 x 1⅜"- (52043516)
52pc. -S8 -Pan Screw #12 x ¾" - (52433603)
18 [e-mail]

14pc. FW0 -3/16" Flat Washer - (51103100)
10pc. LW1 - 1/4" Lock Washer - (51303200)
Hardware Identification (Actual Size)
Accessory Identification (Reduced Size)
7pc. LN3 -3
8" Lock Nut - (54303800)
12pc. LN2 -5
16" Lock Nut - (54303300)
82pc. TN2 -5
16" T- Nut - (54503300)
10pc. BN1 -1/4" Barrel Nut - (54803200)
112pc. FW2 -5
16" Flat Washer - (51103300)
14pc. FW10 -3
8" Flat Washer -Narrow - (51103800)
7pc. FW1 -1/4" Flat Washer - (51103200)
17pc. FW5 - Plastic Formed Washer - (3290000)
(1) Maze N Wave Slide
16pc. LW2 - 5/16" Lock Washer - (51303300)
19 [e-mail]

1-877-817-5682
[e-mail]
B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the consumer relations department directly. Call us
before going back to the store.
STOP STOPSTOP STOP
Key Number: The rst two digits represent the step
number. The third digit represents the piece. Note
that if the part is used in multiple steps then the
number only reects the rst step it is used in.
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
First Step: Inventory Parts - Read This Before Starting Assembly
C. Read the assembly manual completely, paying special attention to ANSI warnings;
notes; and safety/maintenance information on pages 1 - 6.
D. Before you discard your cartons ll out the form below.
• The carton I.D. stamp is located on the end of each carton. The tracking number is
located on the Cedar Summit ID Plaque (9320357).
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
• Please refer to Page 6 for proper hardware assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• The wood pieces will have the key number stamped on the ends of the boards.
Organize the wood pieces by step, as per the key numbering system below.
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 4)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 5)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 6)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 3)
MODEL NUMBER: F25650
TRACKING NUMBER (from ID Plaque):
20 [e-mail]