CEI A100RC+ User manual

User manual
A100RC+
Radiocontroller for LED lights
with integrated 12V transformer
Réf : PF10R057
Table of Contents
1. Pack contents ......................................................................................................................... 2
2. Technical characteristics ........................................................................................................ 2
3. Description ............................................................................................................................. 3
3.1. Lights compatibility .................................................................................................... 3
4. Installation ............................................................................................................................. 4
4.1. Electrical connections ................................................................................................. 4
4.2. Lights connection ........................................................................................................ 5
5. A100RC+ operation ............................................................................................................... 6
5.1. Control interface ......................................................................................................... 6
5.2. Power on ..................................................................................................................... 7
5.3. Turn on / Turn off ....................................................................................................... 7
5.4. Selecting the mode ...................................................................................................... 7
5.5. Radio-frequency remote control .................................................................................. 9
5.6. Adjusting luminous intensity ..................................................................................... 10
5.7. Adjusting the animations speed. ................................................................................ 10
5.8. Selecting the radio code ............................................................................................ 11
A. Declaration of conformity ................................................................................................. 12
Read these instructions carefully before installing, commissioning and using
this product
MPNT0171 v1.0EN (03/07/2017)

User manual A100RC+ v1.0EN
1. Pack contents
• 1 control panel A100RC+ with 4 channels radio remote control "BRiO®"
• 1 bag containing
– 4 screws and 4 dowels (control box + wall holder for the radio remote control)
– wall holder for the radio remote control
• User manual (this document)
2. Technical characteristics
Output Voltage 12V ~ AC 50/60Hz
Input Voltage 220V AC
Power consumption 5W maximum
Switching power (connected lights) 100W maximum
Transformer power 100VA
Protection rating IP-55
Dimensions 148x256x84 mm
Installation
Control box : wall fixation (2 supplied screws/
dowels)
Wallholderfortheremotecontrol:Wallfixation
(2 supplied screws/dowels)
Weight Control box : 390 g / remote control : 40 g
Complete cardboard box : 600 g
Radio remote control
4 channels - Frequency : 433,92Mhz
Battery : alkaline 12V 23A
Power consumption when sending: 18mA max
Power < 0,1 mW- in-built antenna
Range 30m max free field
www.c-
cei.fr 2

User manual A100RC+ v1.0EN
3. Description
A100RC+ enables to power the 12V RGB LED lights BRiO® and to control remotely the colour
changes. Lights have to be connected to A100RC+ . It can control up to 100W (2x X30 lights or
6x X15 lights). The control box requires an input voltage of 220V and is fitted with a SELV 12VC
transformer.
A radio-frequency remote control unit (with wall support) sends instructions to the controller from
a distance, these are then sent to the lights connected to it. Instructions are sent by combinations of
power micro-drops which are then interpreted by the lights. This patented solution is very simple
and can withstand interference, lights several dozens of metres away can be controlled in this way.
3.1. Lights compatibility
All CCEI lights manufactured after February 2016 are compatible with the RC + control mode.
Here is the list:
Light model Reference number
BRIO Eolia WEX30 PF10R200 / V05 (and higher)
BRIO Eolia WEX60 PF10R104 / V05 (and higher)
BRIO Eolia WEX100 PF10R005 / V06 (and higher)
BRIO Gaïa GAX30 PK10R102 / V03 (and higher)
Mini BRIO X15 PK10R303 / V02 (and higher)
BRIO ZX30 PK10R007 / V03 (and higher)
BRIO ZX60 PK10R008 / V02 (and higher)
BRIO ZX100 Pk10R009 / V02 (and higher)
BRIO Stella WPX30 PF10R410 / V04 (and higher)
www.c-
cei.fr 3

User manual A100RC+ v1.0EN
4. Installation
4.1. Electrical connections
Installation of this project involves a hazard of electric shocks. We strongly
recommend you contract a professional installer. Incorrect installation places
you in danger and may irreversibly damage the product and the equipment
connected to it.
For reasons of safety and compliancewith the NF C15-100 standard, the
A100RC+ box must be installed
• over 3m50 from the edge of the pool. This distance includes cable deviations
around obstacles. If the box A100RC+ is installed behind a wall, this will then
be the distance required to complete the loop and connect to the box.
• or in an underground space immediately next to the swimming pool. In this
case the space must be accessible via a hatch which requires a tool to open it.
The box is resistant to splashing but must not be placed in a place that may become flooded. The
box A100RC+ must be placed on a flat and stable surface and attached to the wall using the screws
and wall plugs supplied.
Electrical connection is facilitated by factory-fitting of a 3x2.5mm² cable.
www.c-
cei.fr 4

User manual A100RC+ v1.0EN
4.2. Lights connection
4.2.1. Power supply
The connection has to be made on two connection terminals and on the ground terminal. The
A100RC+ must be powered in 230V 50Hz single-phase and protected by a 30mA residual current
device with an appropriate intensity. A short circuit protection (max 16A) must althrough be in-
stalled on the power line of the control box. The cable section used for the power supply must be
choosen according to the cable length and the number of connected lights on the A100RC+ .
4.2.2. Lights supply
The connection has to be made on a terminal 2 points type "domino".
The total power of the connected lights must never exceed 100W.
www.c-
cei.fr 5

User manual A100RC+ v1.0EN
5. A100RC+ operation
5.1. Control interface
The interface includes a two-digit multi-function display, 3 indicator lights and 3 keys;
Élément Description
Indicator lamp "Radio":This indicator lightlights when receivingradio commands (from
the 4-way remote controller)
Indicator lamp "Lights": Off when the lights are turned off
Flashes when commands are sent (micro-drops) to the lights
Continuously on when the lights are turned on
Key "Up / Plus"
Increases a value and scrolls up the settings
Key "Down / Minus"
Decreases a value and scrolls down the settings
Key "Confirm / OK"
Confirms selection of a parameter / colour / colour change sequence
www.c-
cei.fr 6

User manual A100RC+ v1.0EN
5.2. Power on
When the unit is turned on, various types of information will be successively displayed on the mul-
ti-function display, and all indicator lights and segments of the display will flash in sequence.
Message Meaning
10 Software version loaded in the A100RC+ . (10
= version 1.0)
r1 / r2 / r3 / r4 Current radio code
L1 / L2 / L3 / L4 Current Luminous intensity
d1 / d2 / d3 Speedof colour sequence
5.3. Turn on / Turn off
Pressing the key at any time will turn the lights on or off
•When the lights are turned off, the indicator is off and the message -- appears on the
multi-function display.
•When the lights are turned on, the indicator is on and the currently selected mode appears
on the multi-function display.
When turning back on they will be the same colour or in the same sequence as when they were
turned off.
5.4. Selecting the mode
Brio LED lights are designed to produce harmonious and varied colour variations. 11 set colours
and 7 sequences are available. Sequences are pre-programmed sequences of lights. In this mode the
pool will change colour in sequence at a variable rate.
The mode is changed using key and . The selected mode flashes, then press the
key to confirm it. If the lights do not turn on when selecting the mode, they will turn on after
confirmation.
www.c-
cei.fr 7

User manual A100RC+ v1.0EN
Type Mode Description
F0 White
F1 Blue
F2 Lagoon blue
F3 Cyan
F4 Violet
F5 Magenta
F6 Pink
F7 Red
F8 Orange
F9 Green
Fixed Colour
Fu User's favourite colour
A1 Slow rainbow
A2 Fast rainbow
A3 Sequencing of 11 colours shown below
A4 Psychedelic (flashing colours)
A5 Blue variations (Blue / White / Cyan)
A6 Random sequence of pre-defined colours
Animation
A7 Random sequence of random colours
Resetrt
Resets lights to zero Deletes the favourite colour, intensity settings,
sequencing speed and automatically sets the lights to blue and the
A100RC+ display to F1.
The selected program is saved in the event of a power cut.
Once the mode has been confirmed it will be displayed on the multi-function screen and the corre-
sponding code sent to the lights as micro-drops. The message rc is displayed as the message is sent.
In A1 animation mode, several colour nuances are played. The user may save a colour he particularly
likes while pressing the "pause key" of the remote control when the colour is currently played. The
colour is then stored under Fu. The storage is possible only with the animation mode A1.
www.c-
cei.fr 8

User manual A100RC+ v1.0EN
5.5. Radio-frequency remote control
The radio-frequency remote control can be used to control colour changes from a distance. A wall
mount is also supplied. This mount is attached to a wall using two screws, it holds the remote control
unit when not in use.
Key Function
On / Off
This key turns the lights on and off. When turning back on they will be the
same colour or in the same sequence as when they were turned off.
Set / Program
When the lights are on, this key will switch between "set" and "sequence"
modes. When the pool is lit in set mode, pressing this key will start sequence
n°1 (A1). If a sequence is running when the key is pressed, the pool lighting
will switch to white (F0).
Last and Next
These keys are used to scroll through colours and sequences.
To replace the battery, open the device (using a screwdriver as illus-
trated in the drawing) and replace the battery (12V 23A alkaline).
Check the polarity is correct as shown on the bot-
tom of the device.
www.c-
cei.fr 9

User manual A100RC+ v1.0EN
5.6. Adjusting luminous intensity
It is easier to use the Bluetooth® application to adjust the intensity of the lights. It is still possible
to adjust it from the box A100RC+ . To do this it is necessary to
1. Cut the power to the A100RC+ ,
2. Press the key and hold it,
3. Turn on the A100RC+ ,
4. Release the key,
5. The current intensity setting will be displayed on the screen (L1 / L2 / L3 / L4),
6. Use the keys and to set it again,
7. Press the key to confirm.
The corresponding code sent to the lights in the form of micro-drops. The message rc is displayed
as the message is sent.
Adjusting the intensity setting automatically sets the lights to blue and the A100RC+ display to F0.
The setting is easier to judge in this mode.
5.7. Adjusting the animations speed.
It is easier to use the Bluetooth® application to adjust the sequencing speed of the lights. It is still
possible to adjust it from the box A100RC+ . To do this it is necessary to
1. Cut the power to the A100RC+ ,
2. Press the key and hold it,
3. Turn on the A100RC+ ,
4. Release the key,
5. The current speed setting will be displayed on the screen (d1 / d2 / d3),
6. Use the keys and to set it again,
7. Press the key to confirm.
The corresponding code sent to the lights in the form of micro-drops. The message rc is displayed
as the message is sent.
Adjusting the sequencing speed setting automatically sets the lights to psychedelic mode and the
A100RC+ display to A4. The setting is easier to judge in this mode.
www.c-
cei.fr 10

User manual A100RC+ v1.0EN
5.8. Selecting the radio code
In the event that another radio device is in the vicinity, it may interfere with the operation of your
installation (e.g. a neighbour also has a A100RC+ ), the code can be changed. You will also need to
change the code on the A100RC+ and inside the remote control unit. To do this it is necessary to
1. Cut the power to the A100RC+ ,
2. Press the key and hold it,
3. Turn on the A100RC+ ,
4. Release the key,
5. Change the current radio code which appears on the screen (r1 / r2 / r3 / r4),
6. Use the keys and to set it again,
7. Press the key to confirm.
There are 10 switches inside the remote control unit (under the battery cover)
which are used to set the code. To open the device, use a screwdriver as illus-
trated in the drawing.
The code displayed on the screen (r1 / r2 / r3 / r4) must correspond to the positions of switches
n°5 and 6.
• A "0" corresponds to the "OFF" switch position
• A "1" corresponds to the "ON" switch position
The other switches must always stay in the same position.
Display Code Positions of the switches
r1 0011001010
r2 0011011010
www.c-
cei.fr 11

User manual A100RC+ v1.0EN
Display Code Positions of the switches
r3 0011101010
r4 0011111010
A. Declaration of conformity
Bleu Electrique SAS (FR47403521693) declares that product A100RC
+ is compliant with the safety and electromagnetic compatibility re-
quirements of European directives 2006/95/CE and 2004/108/CE .
Emmanuel Baret
Marseille, on 03/07/2017
Distributor's stamp
Date of sale: . . . . . . . . . . . . . . . . . . . . . . . Batch N°: . . . . . . . . . . . . . . . . . . . . . . . . . . .
www.c-
cei.fr 12