Celestron EXPLORASCOPE 60AZ User manual

INSTRUCTION MANUAL
EXPLORASCOPE 60AZ
Model #22100
EXPLORASCOPE 80AZ
Model #22102
EXPLORASCOPE 70AZ
Model #22101
EXPLORASCOPE 114AZ
Model #22103
ENGLISH

2 | ENGLISH
Lens Cap Lens Cap
Telescope Tube Telescope Tube
Star Pointer Finderscope Star Pointer Finderscope 20 mm Eyepiece
20 mm Eyepiece
Erect Image Diagonal
Tripod Tripod
Accesory Tray Accesory Tray
INCLUDED BUT NOT PICTURED.
(1) 4 mm Eyepiece
(1) 3x Barlow Lens
(1) Bonus Astronomy Software download
SOLAR WARNING
Never look directly at the Sun with the naked eye or with a telescope unless you have the proper solar filter. Permanent and irreversible eye damage may result.
Never use your telescope to project an image of the Sun onto any surface. Internal heat build-up can damage the telescope and any accessories attached to it.
Never use an eyepiece solar filter or a Herschel wedge. Internal heat build-up inside the telescope can cause these devices to crack or break, allowing unfiltered
sunlight to pass through to the eye.
Do not leave the telescope unsupervised, especially when children or adults unfamiliar with the correct operating procedures of your telescope are present.
We recommend saving your telescope box so it can be used to store the telescope when it is not in use. Unpack the
box carefully as some parts are small. Use the parts list below to verify that all parts and accessories are present.
PARTS LIST
WHAT’S IN THE BOX
EXPLORASCOPE 60AZ, 70AZ, and 80AZ EXPLORASCOPE 114AZ

ENGLISH | 3
ASSEMBLING YOUR TELESCOPE
Fig. 4
THE MOUNT
The ExploraScope mount and tripod come fully assembled, so setting it up is easy.
1. Remove the tripod and mount from the box.
2. Loosen the hand knobs at the bottom of each leg and extend the inner section of
the leg to the desired length. Tighten the knobs to secure the legs, being careful
not to over tighten.
3. Stand the tripod upright and pull the tripod legs apart until the center brace snaps
into place.
4. Place the threaded post on the bottom of the accessory tray over the hole in the
middle of the leg support bracket and turn the entire tray clockwise until the tray sits firmly against the leg brace (Fig. 1).
5. Make sure the leg hinge bolts are secure by snugging down the black thumbnuts at the top of each leg.
THE TELESCOPE TUBE
To attach the telescope tube to your tripod and mount:
1. Locate the slow motion rod guide on the side of the U-shaped mount.
Loosen the set screw in the guide until the hole through the guide is
unobstructed.
2. Holding the telescope tube above the mount, slide the slow motion
rod through the guide on the mount and gently lower the hinges
on the sides of the telescope tube into the cradles at the top of the
U-shaped mount (Fig. 2).
3. Tighten the set screw on the guide to hold the telescope
in place
4. Insert the two telescope tube mounting bolts through the tops of
the U-shaped mount and into the hinges on the sides of the telescope
tube. Do not over tighten (Fig. 3).
NOTE: The 70mm refractor is shown, but the 114 mm Newtonian attaches to the mount in the same exact way.
THE STAR DIAGONAL
(FOR 60 MM, 70 MM AND 80 MM REFRACTORS ONLY)
The star diagonal attaches to the back of a refracting telescope that contains a small mirror that reflects the light at a 90°
angle, providing a more comfortable viewing position. It also gives you a 100% correctly oriented image allowing you to
easily use this telescope for daytime terrestrial observing.
1. Remove the caps from both sides of the diagonal.
2. Loosen the setscrews on the back of the focuser and pull out
the small dust cap.
3. Insert the smaller tube on the diagonal into the back of the
focuser and secure it by tightening the setscrews (Fig. 4).
You can rotate the diagonal to any position by loosening the setscrews.
Fig. 3
Fig. 2
Fig. 1

4 | ENGLISH
THE EYEPIECES
Your telescope comes with two eyepieces, a low power (20 mm eyepiece) and a higher power eyepiece (4 mm
eyepiece). Whenever you set up your telescope, always start with the 20 mm eyepiece. Once you have your target
centered in the 20 mm eyepiece, you can switch to your higher power 4 mm eyepiece to get a more detailed view.
To install an eyepiece on the 60 mm, 70 mm, or 80 mm refractor:
1. Loosen the setscrews on the open end of the star diagonal.
2. Insert the silver barrel of the 20 mm eyepiece into the star diagonal
(Fig. 5).
3. Tighten the setscrews to secure the eyepiece
4. To see the sharpest image possible, you need to focus by looking
through the eyepiece and slowly turning the focusing knobs until you
find the sharpest image.
To install an eyepiece on the 114 mm Newtonian:
1. Loosen the two silver setscrews on the focuser and pull out the small
plastic dust cap.
2. Insert the silver barrel on the bottom of the eyepiece into the focuser
(Fig. 6).
3. Tighten the two setscrews to secure the eyepiece.
4. To see the sharpest image possible, you need to focus the eyepiece.
To focus, look through the eyepiece and slowly turn the focusing
NOTE: The 114 mm Newtonian comes with a special 20 mm eyepiece that gives you a correctly oriented image for
daytime terrestrial viewing. The 4 mm is designed for astronomical observing and will give an inverted image.
This is perfectly normal.
THE STAR POINTER FINDERSCOPE
The ExploraScope comes with a Star Pointer finderscope that you will use as a
sighting tool when aiming the telescope at a target.
To install your Star Pointer finderscope:
1. Remove the two silver nuts from the threaded posts at the top
of the tube, near the focuser.
2. Place the two holes in the base of the finderscope over the
threaded posts so the finderscope base sits flush on the
telescope tube. Make sure that the round window on the
finderscope is pointed toward the end of the telescope that you
will point at your target.
3. Thread the two nuts back onto the threaded posts (Fig. 7)
4. There is a small clear plastic tab inserted between the battery
and the contact. This was included to prevent the battery from discharging
during shipment. Pull this out to allow your battery to work.
Fig. 5
Fig. 6
Fig. 7

ENGLISH | 5
ALIGNING THE STAR POINTER FINDERSCOPE
The Star Pointer finderscope helps you aim your telescope by looking through its round glass window and covering your
target with the red dot projected in the window.
The first time you assemble your telescope, you’ll need to align the Star Pointer with the main optics of the telescope.
Although this step can be done at night, it is significantly easier during the day. Once you have completed the
finderscope alignment, you should not have to repeat this step unless the finderscope is bumped or dropped.
To align the Star Pointer:
1. Take the telescope outside during the day. Using your naked eye, find an easily recognizable object, such as a
streetlight, car license plate, or tall tree. The object should be as far away as possible, but at least a quarter mile away.
2. Remove the main dust cover from the telescope and make sure your 20 mm eyepiece in installed.
3. Move the telescope left and right or up and down so that it is roughly pointing toward the object you chose in step 1.
4. Look through the telescope using your 20 mm eyepiece and manually move the telescope until the object you chose
lies in the center of the view. If the image is blurry, gently turn the focus knobs until it comes into sharp focus.
NOTE: The image in the telescope eyepiece will appear upside-down. This is perfectly normal in an astronomical telescope.
5. Once the object is centered in your 20 mm eyepiece, turn on the finderscope by turning the power switch knob
clockwise as far as it will go.
6. With your head positioned about a foot behind the finder, look through the round window and locate the red dot. It
will probably be close to, but not on top of, the object you see when you are looking through the 20 mm eyepiece.
7. Without moving the telescope, use the two adjustment knobs on the side and underneath the Star Pointer. One
controls the left-right motion of the dot, while the other controls the up-down motion. Adjust both until the red dot
appears over the same object you are observing in the 20 mm eyepiece.
Now choose some other distant targets to practice aiming your telescope. Look through the Star Pointer window and
place the red dot on the target you are trying to view and verify that it is the 20 mm eyepiece of the scope.
With your Star Pointer finderscope aligned, your telescope is fully assembled and you are ready to observe!
NOTE: Be sure to turn off the Star Pointer finderscope when not in use to conserve battery power.

6 | ENGLISH
YOUR FIRST ASTRONOMICAL OBSERVING SESSION
THE MOON
Now you are ready to take your telescope out at night and do some real observing!
Let’s start with the Moon. The Moon takes about one month go through a complete phase cycle, from New Moon to Full
Moon and back again. Try observing it at different points during this cycle.
While you can observe the Moon any time it is visible in the night sky, the best time to view it is from two days after a New
Moon up to a few days before a Full Moon. During this period, you will be able to see the most detail in craters and lunar
mountain ranges. Consult a calendar to find out when the next New Moon will be.
1. With a clear view of the Moon, set up your telescope with the 20 mm eyepiece.
2. Turn on the Star Pointer finderscope and look through it to find the red dot.
3. Move the telescope until you can see the Moon through the finderscope’s window and the red dot is centered
on the Moon.
4. Look through the 20 mm eyepiece. Gently turn the focus knobs to adjust the sharpness of the image.
CONGRATULATIONS! YOU HAVE NOW OBSERVED YOUR FIRST CELESTIAL OBJECT!
To get a closer view of the Moon, replace the 20 mm eyepiece with the 4 mm eyepiece. It will give you more magnification,
making the Moon appear much larger. You may need to adjust the focus knobs when you change eyepieces to ensure you
are getting the sharpest image.
You can view many other celestial objects, such as planets, star clusters and nebulae using this same basic technique.
For more tips for about astronomical observing please visit
ExploreTheSky.com
There you will find comprehensive tips to help you get the most from your new telescope including:
• How to observe the planets
• How to locate and observe stars, double stars, star clusters
• How to observe deep-sky objects such as nebulae and galaxies
• How to choose a good location for astronomical observing
• How to evaluate sky conditions

ENGLISH | 7
CELESTRON TWO YEAR LIMITED WARRANTY
A. Celestron warrants your telescope to be free from defects in materials and workmanship for two years. Celestron will
repair or replace such product or part thereof which, upon inspection by Celestron, is found to be defective in materials or
workmanship. As a condition to the obligation of Celestron to repair or replace such product, the product must be returned
to Celestron together with proof-of-purchase satisfactory to Celestron.
B. The Proper Return Authorization Number must be obtained from Celestron in advance of return. Call Celestron at (310)
328-9560 to receive the number to be displayed on the outside of your shipping container.
All returns must be accompanied by a written statement setting forth the name, address, and daytime telephone number of
the owner, together with a brief description of any claimed defects. Parts or product for which replacement is made shall
become the property of Celestron.
The customer shall be responsible for all costs of transportation and insurance, both to and from the factory of Celestron, and
shall be required to prepay such costs.
Celestron shall use reasonable efforts to repair or replace any telescope covered by this warranty within thirty days of
receipt. In the event repair or replacement shall require more than thirty days, Celestron shall notify the customer accordingly.
Celestron reserves the right to replace any product which has been discontinued from its product line with a new product of
comparable value and function.
This warranty shall be void and of no force of effect in the event a covered product has been modified in design or function,
or subjected to abuse, misuse, mishandling or unauthorized repair. Further, product malfunction or deterioration due to normal
wear is not covered by this warranty.
CELESTRON DISCLAIMS ANY WARRANTIES, EXPRESS OR IMPLIED, WHETHER OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR USE, EXCEPT
AS EXPRESSLY SET FORTH HEREIN. THE SOLE OBLIGATION OF CELESTRON UNDER THIS LIMITED WARRANTY SHALL BE TO REPAIR OR REPLACE
THE COVERED PRODUCT, IN ACCORDANCE WITH THE TERMS SET FORTH HEREIN. CELESTRON EXPRESSLY DISCLAIMS ANY LOST PROFITS, GENERAL,
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES WHICH MAY RESULT FROM BREACH OF ANY WARRANTY, OR ARISING OUT OF THE USE OR
INABILITY TO USE ANY CELESTRON PRODUCT. ANY WARRANTIES WHICH ARE IMPLIED AND WHICH CANNOT BE DISCLAIMED SHALL BE LIMITED IN
DURATION TO A TERM OF TWO YEARS FROM THE DATE OF ORIGINAL RETAIL PURCHASE.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation on how long an
implied warranty lasts, so the above limitations and exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Celestron reserves the right to modify or discontinue, without prior notice to you, any model or style telescope.
If warranty problems arise, or if you need assistance in using your telescope contact:
Celestron
Customer Service Department
2835 Columbia Street
Torrance, CA 90503
Tel. [phone]
Fax. [phone]
Monday-Friday 8AM-4PM PST
NOTE: This warranty is valid to U.S.A. and Canadian customers who have purchased this product from an authorized Celestron dealer in the U.S.A. or
Canada. Warranty outside the U.S.A. and Canada is valid only to customers who purchased from a Celestron’s International Distributor or Authorized
Celestron Dealer in the specific country. Please contact them for any warranty service.

8 | ENGLISH
FCC NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Product design and specifications are subject to change without prior notification.
This product is designed and intended for use by those 14 years of age and older.
© 2017 Celestron • All rights reserved
celestron.com
2835 Columbia Street • Torrance, CA 90503 U.S.A.
Telephone: [phone]
2-17
Printed in China