Celexon Professional Radio Trigger User manual
Operating instructions
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully
before connecting or operating this product. Please retain these instructions for future
reference.
celexon Professional
Radio Trigger
Version: 32422_101
1
The purpose of these operating instructions is to familiarise you with the operation of
this product. Therefore, keep these instructions in a safe place so that you can refer to
them at any time.
• Do not start assembly until you have read and understood the complete operating
instructions.
• Remove the product from its packaging and remove all packaging materials.
Make sure that there is no packaging material on or in the product. If you notice
any damage to the packaging, also check whether there is any damage to the
product. If you notice any external damage to the unit or any unexpected or unusual
functioning, do not continue to use the product. Contact the dealer from whom
you purchased the product or celexon directly (Web: www.celexon.co.uk, Mail:
info@celexon.co.uk) for further information.
• To ensure trouble-free operation, the product must only be used indoors, it is NOT
suitable for outdoor use.
• The use of the product and accessories is prohibited for children under 16 years
of age. Ensure that children do not play with the appliance or stay in the vicinity
without supervision.
• Caution: Risk of injury! Never open the product without authorisation. Never carry
out repairs yourself!
• Do not use the product in the vicinity of escaping gas, water or in a dusty environ-
ment. Do not use or on/near metallic surfaces (reception interference).
• Handle the product with care. It can be damaged by knocks, blows or falling from a
from even a small height.
• Keep the product away from moisture and heat.
• Never immerse the product in water or other liquids.
• Only use the product in its intended manner. Any use outside of this may result in
damage to the product or its surroundings.
• Only use the product with the specied voltage.
• If you no longer use the trigger for control, remove it from your wiring to save
energy.
• All leads and cables must not be subjected to additional loads and must be laid in
such a way that they are not damage or crushed.
• Failure to follow the above instructions may result in personal injury and damage to
the product. Incorrect installation or use may also invalidate the warranty.
• If you are unsure about the use of the product, please contact your specialist
WARNINGS
2
personnel, your dealer or celexon directly (Web: www.celexon.co.uk, Mail:
info@celexon.co.uk).
• Technical changes and errors expected.
The manufacturer accepts no responsibility for damage to property or personal injury if
the screen is used outside the recommended specications, or in the event of improper
installation.
DISCLAIMER
The information in this document is subject to change without notice by the
manufacturer. Changes will be added to subsequent versions of this manual.
The manufacturer does not guarantee or warranty for the correctness of the
information in this document.
TECHNICAL DATA
• Voltage: 230VAC 50Hz max.
• Temperature range: 0°C ~ +45°C
• Frequency: 433.92 MHz
• Consumption: ≥180mA
• Transmitting power: ≤10mW
• Power rating: ≤2000W
3
IN THE BOX
INSTALLATION NOTES
The receiver is compatible with celexon radio receivers of the professional
series. Please refer to the connection diagram for the connection method.
Please observe the electrotechnical standards and the following points:
• Minimum distance between trigger and receiver: 30 cm
• Minimum distance between two triggers: 20cm
• Please ensure that the connection is made to an earthed circuit. If
necessary, have the circuit protected and checked by a qualied
electrician.
• Only connect and teach-in the trigger with dry hands indoors!
• The trigger is plugged into your projector and then connected to the
existing power circuit using the power cable of your projector.
Product features
• Triggers (controls and automates) your screen by switching your projec-
tor on / off per radio transmission (no visual contact required).
Radio trigger
4
CAUTION
CONNECTING
In order to use the trigger, the celexon Professional radio receiver is required!
Please note the following information on the use of electrical devices:
1. Disconnect devices from the
power supply during installation!
3. Connect only to an earthed
circuit!
2. Avoid static charge!
4. Do not touch any metallic
objects during installation!
5
LEARNING
With the trigger in-
stalled between the
projector and power
(see Connection
method.)
The trigger automatically
detects the switch-on vol-
tage
Switch your
projector on
The process is
successful
The process has
failed and must be
repeated
Press and hold ‘set’ button
on the back of the trigger
for 3 seconds
The LED on the trigger ashes for 10
seconds & beeps 1x within this time
The LED on the
trigger ashes 1x and
beeps 1x
The LED on the
trigger ashes 3x and
beeps 3x
Hint:
The trigger detects the difference between standby and operating voltage of
your projector and can send the appropriate radio signal to your screen.
When teaching, make sure that your projector is in standby and not completely
switched off.
6
PAIRING
Switch on the
receiver
Press the pro-
gramming button
on the trigger 1x
Press the ‘code’ button
on your Professional radio
receiver 1x
LED1 on the receiver
no longer ashes
LED1 on the
Receiver ashes
Programming
completed!
If after 10 sec, no
input is made,
the receiver will
switch back to
normal mode
7
Manufacturer: celexon Europe GmbH
Address: Gutenbergstraße 2, 48282 Emsdetten, DE
Product name: celexon Professional Radio Trigger
Hereby celexon Europe GmbH declares that the celexon Professional Radio
Trigger complies with the directive 2014/53/ EU. The EU declaration of confor-
mity can be downloaded from the following address: www.celexon.de/zertikate
INFORMATION ON EU CONFORMITY
The symbol indicates the separate collection of electrical and
electronic goods in EU countries. Please do not throw the appliance
into the household waste. Find out about the take-back system
in force in your country and if you have any questions about the
disposal process, contact your local authority or your local recycling
and hazardous waste collection centre.
8
Manufacturer: celexon Europe GmbH
Address: Gutenbergstraße 2, 48282 Emsdetten, DE
Product name: celexon Professional Radio Trigger
Hereby celexon Europe GmbH declares that the radio equipment type celexon
Professional Radio Trigger complies with the Radio Equipment Regulations
2017. The UK declaration of conformity can be downloaded from the following
address: www.celexon.de/zertikate
INFORMATION ON UK CONFORMITY
The symbol indicates the separate collection of electrical and
electronic goods in EU countries. Please do not throw the appliance
into the household waste. Find out about the take-back system
in force in your country and if you have any questions about the
disposal process, contact your local authority or your local recycling
and hazardous waste collection centre.
Table of contents
