Cellacom M131 User manual

1
User manual
Model: M131
Brand: Cellacom

2
SAFETY PRECAUTIONS
Please read the following safety guidelines before using the device.
Do not use the phone while you are driving.
Do not place magnetic storage media near your phone.
Radiation from the phone may erase the information
stored on them.
Keep your phone and its accessories away from children.
Mobile phones can interfere with the functioning of
medical devices such as hearing aids or pacemakers.
People having active medical implants should keep their
cell phone at least 10 mm away from the implant.
Permanent hearing loss may occur if you use earphones
or headphones at high volume.
Use a wireless hands-free system (headphone/ headset)
with a low power Bluetooth emitter.
Make sure the cell phone has a low SAR.

3
Keep your calls short or send a text message (SMS)
instead. This advice applies specially to children
adolescents and pregnant women.
Use cell phone when the signal quality is good.
Notice:
Do not dismantle the device or accessories otherwise,
manufacturer is not liable to pay for damages as the device
and accessories are not covered by warranty.
Use only original batteries and charging devices.
Please back up your important data timely and keep them
properly. The company is not liable for any failure to call or
loss of data due to miss-operation, poor signal or power cut,
etc.
All the screens in this manual are for reference only, and
some contents actually displayed may depend upon the
presetting of the service provider or the network operator, or
the SIM card. If any functions referred to in this manual are
different from those of your device, please follow your device.
Do not put use it in a place with flammable gas such as a
petrol pumps. The temperature recommended for using the
device is 5-35℃. Do not touch the charger, power cable or
socket with wet hands. This may cause an electric shock.

4
UNDERSTANDING YOUR DEVICE
General Information
Your device encloses features, such as 1.3 MP Camera, Video Player,
Audio Player, FM Radio etc. The SIM card inserted in the slot1 is
called Master SIM, and the other one in the slot2 is known as Slave
SIM.
Function of Keys
Key
Description
Master SIM
Key
To make/answer a call from Master SIM.
In the standby mode, press this key to view
Call Logs.
Slave SIM
/LSK/Menu
Key
To make a call from Slave SIM.
In the standby mode, press the key to access
Main Menu.
RSK/Right Soft
Key
Use RSK to execute the functions indicated at
the right of the prompt bar on the screen.
End/Power Key
End an ongoing call. Press and hold this key to
turn on or off the device.

5
Navigation
Keys
In the editing mode, use the keys to move the
cursor.
In the standby mode, press the keys to access
the function assigned to these keys.
Keypad
Use to enter numbers, letters and special
characters.
Press RSK and # key to lock/unlock screen.
GETTING STARTED
Please switch off your device before inserting or removing the
battery/SIM card or memory card.
Installing SIM Card and Battery
Your device is provided with two SIM slots for two different SIM
cards. The SIM card inserted in the slot1 is called Master SIM, and
the other one in the slot2 is known as Slave SIM.
Remove the back cover of the device.

6
Hold the phone with the front facing downwards; pull the
cover.
Insert the SIM cards and battery in the device.
Attach the battery.
Push the battery cover until it clicks into place.
Installing Memory Card
Your device supports T-Flash card, which is a multimedia memory
card used to multiply the memory of the device. The T-flash card is
small and should be pulled out and installed carefully and prudently
in order to avoid any kind of damage.
Switch off your device.
Remove the battery cover.
Slide the T-Flash card into the slot.
Attach the battery.
Push the battery cover until it clicks into place.
Charging the Battery
The device prompts a warning tone and message stating insufficient
battery when the battery power of your device is low.
Please follow the instructions mentioned below to charge your device:
Plug the connector of the charger into the jack of the

7
device.
Plug the charger into a standard AC wall outlet.
Note: When power charging is shown on the screen, it indicates that there is
not enough power and you should now charge your device. When charging is
complete, the battery icon will stop flashing. You must fully charge the battery
before using the device for the first time. It is recommended to charge the
battery for four hours before using the device for the first time. If the device is
turned on during charging, you can still make or answer calls, but this will
consume battery power, thus will extend the charging time of the device.
Switch On/Off the Device
To turn on/off the device, press and hold the End/Power Key. If you
have enabled the SIM Lock function then enter the PIN code (4 to 8
digits secret code of your SIM card). It is preconfigured and provided
to you by your network operator or retailer. If you enter an incorrect
PIN code 3 times in succession, your SIM card will be locked. To
unlock it, you must obtain a code from your network operator.

8
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is
subject to the condition that this device does not cause harmful
interference.
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

9
Specific Absorption Rate (SAR) information:
This GSM phone meets the government's requirements for exposure
to radio waves. The guidelines are based on standards that were
developed by independent scientific organizations through periodic
and thorough evaluation of scientific studies. The standards include
a substantial safety margin designed to assure the safety of all
persons regardless of age or health.
FCC RF Exposure Information and Statement
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of
tissue. Device types: M131
(FCC ID: 2AF6M3396993M131) has also been tested against this
SAR limit. The highest SAR value reported under
this standard during product certification for use at the ear is
0.390W/kg and when properly worn on the body is 0.758W/kg. This
device was tested for typical body-worn operations with the back of
the handset kept 10mm from the body. To maintain compliance with
FCC RF exposure requirements, use accessories that maintain a
10mm separation distance between the user's body and the back of
the handset. The use of belt clips, holsters and similar accessories
should not contain metallic components in its assembly. The use of
accessories that do not satisfy these requirements may not comply
with FCC RF exposure requirements, and should be avoided.

10
Body-worn Operation
This device was tested for typical body-worn operations. To comply
with RF exposure requirements, a minimum separation distance of
10mm must be maintained between the user’s body and the handset,
including the antenna. Third-party belt-clips, holsters, and similar
accessories used by this device should not contain any metallic
components. Body-worn accessories that do not meet these
requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or an approved antenna.