Cellar Cool CM TWIN H.E. User manual

CM 58*/)&
OWNER’S MANUAL
NOTICE: To activate the split system warranty,
the installing certied HVAC/R service tech
must complete the split system warranty
checklist and send back to CellarCool.

Copyright © 2017. CellarCool. All rights reserved.
CellarCool copyrights this manual, the product design, and the design concepts, with all rights reserved. Your rights with
regard to the hardware and manual are subject to the restrictions and limitations imposed by the copyright laws of the
USA. Under copyright laws, this manual may not be copied, reproduced, translated, transmitted, or reduced to any printed
or electronic medium or to any machine-readable form, for any purpose, in whole or in part, without the written consent
of CellarCool.
Every effort has been made to ensure that the information in this manual is accurate. CellarCool is not responsible for
printing or clerical errors.
CellarCool reserves the right to make corrections or improvements to the information provided and to the related
hardware at any time, without notice.
Vinothèque and CellarCool are registered trademarks, and ECE is a trademark of CellarCool. All rights reserved.
Mention of third-party products is for informational purposes only and constitutes neither an endorsement nor a
recommendation. CellarCool assumes no liability with regard to the performance or use of these products.
We manufacture, test and certify 100% of our wine cooling units in
the USA. By sourcing the best components and closely controlling our
manufacturing processes, we can assure the highest-quality,
lowest defect manufacturing rates in the industry.
Conforms to ANSI/UL Std 427
Certied to CAN/CSA Std C22.2 No. 120

*OUSPEVDUJPOyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
#FGPSF:PV4UBSUyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
1SFQBSJOH5IF8JOF$FMMBSyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
3FDFJWJOH*OTQFDUJOH5IF4ZTUFNyyyyyyyyyyyyyyyyyyyyyyyyyyy
2VJDL3FGFSFODF(VJEFyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
,OPDLPVU-PDBUJPOTyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
-JRVJE.FBTVSJOH5IFSNPTUBU4ZTUFN#PUUMF1SPCF,%5yyyyyyyyyyyyyyyyy
*UFNT5P3PVUF#FGPSF*OTUBMMJOH5IF&WBQPSBUPS6OJU,%5yyyyyyyyyyyyyyyyyy
75IFSNPTUBU$POWFSTJPO,JU8JSJOH*OTUSVDUJPOTyyyyyyyyyyyyyyyyyyyy
4FMFDUJOH.PVOUJOH0QUJPOTyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
.PVOUJOH5IF&WBQPSBUPS6OJUyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
*OTUBMMJOH5IF&WBQPSBUPS6OJUyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
$POOFDUJOH5IF-JOFTFUyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
*OTVMBUJPO#MBOLFU*OTUBMMBUJPOyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
%SBJO-JOFyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
8BMM.PVOU#SBDLFU*OTUBMMBUJPOyyyyyyyyyyyyyyyyyyyyyyyyyyyy
'MVTI.PVOU#SBDLFU*OTUBMMBUJPOyyyyyyyyyyyyyyyyyyyyyyyyyyyy
&WBQPSBUPS6OJU8JSJOH%JBHSBNo,%5yyyyyyyyyyyyyyyyyyyyyyyyyy
&WBQPSBUPS6OJU8JSJOH%JBHSBNo7yyyyyyyyyyyyyyyyyyyyy
$POEFOTJOH6OJU8JSJOH%JBHSBNyyyyyyyyyyyyyyyyyyyyyyyyyyyy
-JOF4FU1JQJOH%JBHSBNyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
1SFQBSJOH5IF$POEFOTJOH6OJUyyyyyyyyyyyyyyyyyyyyyyyy
$POEFOTJOH6OJU8JSJOHyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
*OTUBMMJOH5IF$POEFOTJOH6OJUyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
%JTQMBZ-BZPVU"OE4QFDJGJDBUJPOTyyyyyyyyyyyyyyyyyyyyyyyyyyy
'JOBMJ[JOHUIF*OTUBMMBUJPOyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
'JMUFSyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
-JOF4FU%SBJO5VCFBOE&MFDUSJDBM$POOFDUJPOTyyyyyyyyyyyyyyyyyyyyyy
4QFFE4XJUDIyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
$POUSPMMFS'VODUJPOTyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
*DPO(MPTTBSZyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
"MBSN$PEFTyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
6TFS.FOVyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
5SPVCMFTIPPUJOH(VJEFyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
4ZTUFN0QFSBUJPOo,%5yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
4ZTUFN0QFSBUJPOo7yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
.BJOUFOBODF4DIFEVMFyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
5FDIOJDBM"TTJTUBODFyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
8BSSBOUZ*OGPSNBUJPOyyyyyyyyyyyyyyyyyyyyyyyyyyyy
8BSSBOUZ3FHJTUSBUJPOyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
1BHF
5BCMF0G$POUFOUT

INTRODUCTION
Customer Service
Thank you for purchasing a CellarCool cooling system. We strive to provide the highest-quality products and the best possible
customer service. If you have any questions about your system, please call us at 1-800-343-9463 or visit cellarcool.com.
Using the Manual
This owner’s manual is intended to assist in the proper maintenance of the cooling system. In order to ensure the longevity of
your cooling unit, the equipment should be installed as outlined in the technician’s manual. It is also vital to establish a proper
care and maintenance schedule. Please read and review this manual carefully and keep it for future reference.
What is the CellarCool Cooling System?
The CellarCool cooling system is a specialized refrigeration system designed for one purpose only: to maintain the optimal
temperature and humidity levels conducive to the proper storage and aging of ne wines. This system produces minimal in-cellar
noise and has the most lenient exhaust requirements. An exterior housing is required for outdoor condensing unit installations.
How Does the Cooling System Work?
Similar to the air conditioning systems used for homes, the evaporator unit and condensing units are installed in separate
locations and are connected by a refrigerant line set. The evaporator portion is commonly installed in the wine cellar, with the
condensing unit is located either outside or in a remote indoor location that is ventilated. An exterior housing is required for
outdoor condensing unit installations.
Temperature Setting
The system is designed to maintain a cellar temperature of 55°F as long as the ambient temperature does not exceed 110°F.
Page 2
08/09/21

BEFORE YOU START 1-800-343-9463
Inspect all components prior to installation. If damageEPSNJTTJOHDPNQPOFOUTBSFGPVOE, please contact your distributor
or CellarCool CustomerService at 1-800-343-9463.
The evaporator unit requires a dedicated 1V, 15-amp circuit. The condensing unit requires a dedicated V, -amp
circuit. Use a surge protector with the unit.%POPUVTFB('*(ground fault interrupter) linePSCSFBLFS.
$PNNVOJDBUJPODBCMFUIFSNPTUBUXJSFNVTUCFSBOCFUXFFOUIFDPOEFOTJOHVOJUBOEUIFFWBQPSBUPSVOJU0OMZPGUIF
DPNNVOJDBUJPOXJSFTXJMMCFVTFE'PS7UIFSNPTUBUFRVJQQFETZTUFNTBODBCMFNVTUCFVTFEUPDPOOFDUUIF
UIFSNPTUBUUPUIFFWBQPSBUPSVOJU
You are REQUIRED to install a drain line to remove condensation from the evaporator unit.
The warranty is not active until a warranty checklist has been received, reviewed, and approved.
The system is intended for use in properly designed and constructed wine cellars. Hire a professional wine storage
consultant with a valid contractor’s license to build your wine cellar.
CellarCool requires that all split systems be installed by a certified HVAC-R technician only. NATE or equivalent is
recommended
*UJTWJUBMUIBUUIFVOJUTCFTFUBQBSUBOEPSJFOUFETPUIBUUIFTVQQMZBJSGSPNPOFVOJUEPFTOPUSFDJSDVMBUFJOUPUIF
SFUVSOBJSPGUIFPUIFSVOJU
If you encounter a problem with your CellarCool system, please refer to the Troubleshooting Guide. If you have any further
questions or concerns, or need technical assistance, please contact CellarCool’s Customer Service at 1-800-343-9463. Please be
sure all testing has been completed prior to contacting Customer Service. Please have your results ready for your representative.
Page 3
08/09/21

13&1"3*/(5)&8*/&$&--"3
5IFQFSGPSNBODFBOEMJGFPGZPVSTZTUFNJTDPOUJOHFOUVQPOUIFTUFQTZPVUBLFJO
QSFQBSJOHUIFXJOFDFMMBS*NQSPQFSMZQSFQBSJOHZPVSFODMPTVSFPSJODPSSFDUMZJOTUBMMJOH
ZPVSVOJUNBZDBVTFVOJUGBJMVSFMFBLJOHPGDPOEFOTBUJPOBOEPUIFSOFHBUJWe side eFDUT
*UJTIJHIMZSFDPNNFOEFEUIBUZPVPCUBJOUIFBTTJTUBODFPGBXJOFTUPSBHFQSPGFTTJPOBM
8JOFTUPSBHFQSPGFTTJPOBMTXPSLXJUIMJDFOTFEDPOUSBDUPSTSFGSJHFSBUJPOUFDIOJDJBOTBOESBDLJOHDPNQBOJFTUPCVJME
XFMMJOTVMBUFECFBVUJGVMBOEQSPUFDUJWFXJOFDFMMBST8FIBWFQVUUPHFUIFSTPNFVTFGVMUJQTUPBTTJTUJOUIF
JOTUBMMBUJPOQSPDFTT0VSSFDPNNFOEBUJPOTBSFNFBOUUPBDUBTBHVJEFJOUIFQSPDFTTPGCVJMEJOHBQSPQFSFODMPTVSF
:PVSJOUFOEFEMPDBUJPONBZIBWFTQFDJGJDOFFETXIJDIXFEPOPUBEESFTT
Wall & Ceiling Framing
#VJMEXJOFDFMMBSXBMMTVTJOHTUBOEBSEYPSYCPBSETBOEDFJMJOHKPJTUTXJUIPVUWJPMBUJOHMPDBMPSTUBUFDPEFTJO
ZPVSBSFB"TBHFOFSBMSVMFUIFUIJDLFSUIFXBMMTBOEUIFIJHIFSUIFJOTVMBUJPOWBMVFUIFNPSFDPOTJTUFOUZPVSDFMMBS
UFNQFSBUVSFXJMMCF
Insulation
*OTVMBUJPOJT3&26*3&%JOPSEFSUPQSPQFSMZVTFPVSQSPEVDUT*UJTWJUBMUIBUBMMXBMMTBOEDFJMJOHTCFJOTVMBUFEUP
LFFQUIFDFMMBSUFNQFSBUVSFBTDPOTJTUFOUBTQPTTJCMFEVSJOHUIFTVNNFSBOEXJOUFSNPOUIT4UBOEBSEGJCFSHMBTTPS
SJHJEGPBNJOTVMBUJPOJTOPSNBMMZVTFEJODFMMBSDPOTUSVDUJPOJOTPNFDBTFTiCMPXOJOwJOTVMBUJPOJTVTFE5IF3
WBMVFPSRVBMJUZPGJOTVMBUJPOJTEFUFSNJOFECZUIFSBUFBUXIJDIIFBUQBTTFTUISPVHIUIFJOTVMBUJPO5IFIJHIFSUIF
3WBMVFUIFNPSFSFTJTUBOUUIFJOTVMBUJPOJTUPDPOEVDUJOHIFBUBOEUIFNPSFDPOTJTUFOUZPVSXJOFDFMMBST
UFNQFSBUVSFXJMMCF6TJOHIJHIFS3WBMVFTJOJOTVMBUJPOXJMMMPXFSZPVSPQFSBUJOHDPTUTBOEVOJUSVOUJNF3JT
UIFSFDPNNFOEFENJOJNVN3JTQSFGFSSFEGPSJOUFSJPSDFMMBSXBMMTBOE3GPSDFJMJOHTBOEFYUFSJPSXBMMT
Vapor Barrier
8BUFSWBQPSDSFBUFTJUTPXOQSFTTVSFTFQBSBUFGSPNUIFBNCJFOUBJSQSFTTVSFBOEXJMMJOUSVEFJOUPDPMEFSESJFSBSFBT
"WBQPSCBSSJFSJT3&26*3&%JOPSEFSUPQSFWFOUUIFJOUSVTJPOPGXBUFSWBQPSBOENBJOUBJOUIFDPSSFDUDFMMBS
UFNQFSBUVSFBOEIVNJEJUZ*UJTSFDPNNFOEFEUIBUNJMMJNFUFSQMBTUJDTIFFUJOHCFBQQMJFEUPUIFXBSNTJEFPGUIF
DFMMBSXBMMT5IFWBQPSCBSSJFSNVTUBMTPCFBQQMJFEUPUIFPVUTJEFXBMMTBOEDFJMJOH*GJUJTJNQPTTJCMFUPSFBDIUIF
PVUTJEFUIFOUIFQMBTUJDNVTUCFBQQMJFEGSPNXJUIJOUIFDFMMBS5IFNPTUDPNNPONFUIPEJTUPXSBQUIFFOUJSF
JOUFSJPSMFBWJOHUIFQMBTUJDMPPTFJOUIFTUVEDBWJUZTPUIFJOTVMBUJPODBOCFQMBDFECFUXFFOFBDITUVE"MMPGUIF
XBMMTBOEDFJMJOHNVTUCFXSBQQFEJOQMBTUJDGPSBDPNQMFUFWBQPSCBSSJFS
*OBSFBTPGIJHIIVNJEJUZTVDIBT4PVUIFSOBOE(VMG4UBUFTUIFWBQPSCBSSJFSXJMMQSFWFOUJOGJMUSBUJPOPGXBSNNPJTU
BJS5IFNPJTUBJSDBODBVTFNPMEUPGPSNBOETUBOEJOHXBUFSJOESBJOQBOTQSPNPUFNJDSPCJBMBOEGVOHBMHSPXUI
UIBUDBVTFVOQMFBTBOUPEPSTBOEJOEPPSBJSRVBMJUZQSPCMFNT*GNPMEJTGPVOESFNPWFJUJNNFEJBUFMZBOETBOJUJ[F
UIBUQPSUJPOPGUIFVOJU
/PUF)JHIIVNJEJUZTJHOJGJDBOUMZJODSFBTFTUIFIFBUMPBEPOUIFDPPMJOHTZTUFN
"OZCSFBLJOUIFWBQPSCBSSJFSTDVUOBJMIPMFPWFSMBQQJOHFUDXJMMDBVTFBNPJTUVSFMFBLBOENVTUCFTFBMFE5IF
FMFDUSJDDPOEVJUJTBiEVDUwGPSWBQPSUPUSBWFMJO 5IFDPOEVJUTIPVMECFDBVMLFEBOETFBMFEPOUIFXBSNBJSFOE
Page 4
08/09/21

Unobstructed Airflow
6OPCTUSVDUFEBJSGMPXUPBOEGSPNUIFTZTUFNJTDSJUJDBMGPSUIFFWBQPSBUPSVOJUBOEDPOEFOTJOHVOJUTPWFSBMM
QFSGPSNBODFBOEMJGFTQBO"NJOJNVNPGGFFUPGDMFBSBODFGFFUJTJEFBMPOBMMTJEFTJTDSVDJBM5IFBJSUIFGBOTCMPX
OFFETUPDJSDVMBUFBOEFJUIFSEJTTJQBUFPSBCTPSCIFBUGSPNUIFTQBDF5IFNPSFBJSUPFYDIBOHFUIFNPSFFGGJDJFOUUIF
TZTUFNXJMMPQFSBUF
/PUF"WPJEBUUFNQUJOHUPDBNPVGMBHFUIFVOJU5IJTXJMMSFTUSJDUBJSGMPXBOEUIVTUIFTZTUFNTBCJMJUZUPXPSLFGGJDJFOUMZ
Door and Door Seal
"OFYUFSJPSHSade (1¾wEPPSNVTUCFJOTUBMMFEBTBDFMMBSEPPS*UJTFTTFOUJBMUIBUXFBUIFSTUSJQQJOHJTBUUBDIFEUPBMMTJEFTPG
UIFEPPSKBNC"CPUUPNiTXFFQwPSUISFTIPMEJTBMTPSFRVJSFE5IFEPPSNVTUIBWFBWFSZHPPEWBQPSTFBMUPQSFWFOUXBSNFS
NPJTUBJSGSPNMFBLJOHJOUPUIFDFMMBS0OFPGUIFNPTUDPNNPOQSPCMFNTXJUIDPPMJOHTZTUFNTSVOOJOHDPOUJOVBMMZJTEVFUP
UIFEPPSOPUTFBMJOHQSPQFSMZ*ODBTFTXIFSFHMBTTEPPSTBSFVTFEBOEUIFSPPNTJ[FJTDMPTFUPUIFSFDPNNFOEFE
TZTUFNTJ[FUIFOFYUMBSHFSTJ[FTZTUFNTIPVMECFVTFE5IJTXJMMDPNQFOTBUFGPSUIFJOTVMBUJPOMPTTEVFUPUIFMPXFS
JOTVMBUJOHSBUJOHPGHMBTT
13&1"3*/(5)&8*/&$&--"3$0/5*/6&%
Ventilation
The necessity of dissipating heat away from the condensing unit is critical to the unit’s performance and cannot be overstated. As
the system operates and cools, a greater amount of heat is generated on the condensing side of the system. Adequate ventilation
is required in order to dissipate heat away from the condensing unit. If ventilation is inadequate, the exhaust will heat up the
area or room and adversely affect the system’s ability to cool. "WPJEJOTUBMMJOHUIFDPOEFOTFSJOBDMPTFUPSPUIFSTNBMMSPPNTBOE
TQBDFT5IJTXJMMDBVTFUIFTZTUFNUPPWFSIFBUBOEWPJEUIFXBSSBOUZ
/PUF If you are unsure about having adequate ventilation in your install location, please DPOUBDUVTUPBTTFTTZPVSTQFDJGJD
JOTUBMMBUJPO
Ambient Temperature Factor
The cooling system has the ability to cool a wine cellar efficiently to 55°F as long as the ambient temperature of the
area that it is exhausting to does not exceed 10°F. Therefore, you want to exhaust the condensing unit in a space which will
not exceed 10°F. Otherwise the system will not have the capacity to keep the wine at a desirable 55°F.
8"3/*/("MMPXJOHZPVSTZTUFNUPPQFSBUFJOUFNQFSBUVSFTPG¡PSBCPWFGPS
FYUFOEFEQFSJPETPGUJNFXJMMHSFBUMZEFDSFBTFUIFMJGFPGZPVSTZTUFNBOEWPJE
ZPVSXBSSBOUZ5IFDPPMFSUIFUFNQFSBUVSFPGUIFBJSFOUFSJOHUIFDPOEFOTFSDPJM
UIFNPSFDPPMJOHDBQBDJUZUIFTZTUFNIBT5IFMFTTIFBUHBJOUISPVHIUIF
DPNNPOXBMMUIFMFTTUIFFMFDUSJDJUZDPOTVNQUJPO
Page 5
08/09/21

3&$&*7*/(*/41&$5*/(5)&4:45&.
•Use caution when lifting and check package for damage.
•Lift only at the designated hand-hold locations on the shipping container, or fully support the container from
underneath. A shipment may include one or more boxes containing accessories.
•Before opening the container, inspect the packaging for any obvious signs of damage or mishandling.
•Write any discrepancy or visual damage on the bill of lading before signing.
•Allow the condensing unit to sit for 24 hours prior to startup. The condensing unit can be placed in the
installation location, piped and evacuated during this time.
/PUF $FMMBS$PPM units are manufactured in the USA and tested prior to shipment.
•Review the packing slip to verify contents.
•Check the model number to ensure it is correct.
•Check that all factory options ordered are listed.
If any items listed on the packing slip do not match your order information,
contact $FMMBS$PPM Customer Service immediately.
Check all shipped boxes for the following contents:
Please leave the system in its original box until you are ready for installation. This will allow you to move the product safely
without damaging it. When you are ready to remove the product from the box, refer to the installation instructions.
5*1 Save your box and all packaging materials. They provide the only safe means of transporting/shipping the system.
Evaporator Unit Box 1 Condensing Unit Box
(1) 1SJNBSZ evaporator unit
Evaporator installation hardware bag (QSJNBSZ):
•(12) 2½” Phillips wood screws
•(12) #8 ⁄” Phillips pan-head screws
•(1) Bypass plug
•(1) ¼” barbed coupling
•(2) 3” strips of cork tape
Documentation bag (QSJNBSZ):
•C.Twin owner’s manual
•)&R-134a split system warranty checklist
(1))& condensing unit
KDT Plus hardware bag:
•(1) ⁄” OD grommet
•(2) ½” nylon hole plugs
•(4) #6 x 1” Phillips zinc Type A screws
•(4) 8-10 x ⁄” blue plastic screw anchors
Accessory kit bag (QSJNBSZ):
•Stainless steel probe (50 feet)
•KDT Plus display cable (50 feet)
•KDT Plus wall mount bracket assembly
•KDT Plus ush mount bracket assembly
•KDT Plus display assembly
•Flush mount template
•Evaporator installation hardware bag
•KDT Plus hardware bag
Insulation blanket bag (QSJNBSZ:
•(1) C.insulation blanket
Evaporator Unit Box 2
(1) SFDPOEBSZ evaporator unit
Evaporator installation hardware bag (sFDPOEBSZ)
Insulation blanket bag (sFDPOEBSZ):
•(1) C.insulation blanket
Evaporator installation hardware bag (sFDPOEBSZ):
•(12) 2½” Phillips wood screws
•(12) #8 ⁄” Phillips pan-head screws
•(1) Bypass plug
•(1) ¼” barbed coupling
•(2) 3” strips of cork tape
Page 6
08/09/21

QUICK REFERENCE GUIDE
5PQ7JFX
#PUUPN7JFX
.PVOting BrBDLFU1BJOUBCMF
Supply and RFUVSn GrJMMF1BJOUBCMF
&WBQPSBUor Unit (Fan Coil Unit)
ElecUSical KOPDLPVUT
/PUe:5IFVOJUDPNFTJOCMBDL5IFNPVOUJOHCSBDLFUBOEGSPOUHSJMMF
BSFQBJOUBCMFFOBCMJOHZPVUPNBUDIZPVSEFTJSFEDPMPS
5op PBOFM
26*$,3&'&3&/$&(6*%&
Line Set Knockout (x6)
ElecUSical KOPDLPVU
Options
Line Set KOPDLPVU
Options
0QUJPOBM-JOF4FUBOE
&MFDUSJDBM0QFOJOHT
Page 7
08/09/21

PROPRIETARY AND CONFIDENTIAL
1(;7$66<
,/0$,OUT L0$"TIONS
Top View of Evaporator Unit
Front View of Evaporator Unit
,/0$,065-0$"5*0/4
4JEF7JFXPG&WBQPSBUPS6OJU
#BDLView of Evaporator Unit
Page 8
08/09/21

-*26*%.&"463*/(5)&3.045"54:45&.#055-&130#&,%5
0VSDPPMJOHVOJUTDPNFXJUIBMJRVJEUFNQFSBUVSFNFBTVSJOHUIFSNPTUBU5IFTFMGDBMJCSBUJOHQSPCFDPOUBJOTBTFOTPSDIJQ
XIJDIDPNNVOJDBUFTCBDLBOEGPSUIXJUIUIFUIFSNPTUBU5IJTSFTVMUTJOBDPOTJTUFOUUFNQFSBUVSFTFUUJOHBOEBDDVSBDZ
8JOFTIPVMECFLFQUBUBWFSZQSFDJTFDPOUSPMMFEUFNQFSBUVSFBOEIVNJEJUZ
Setting up the Bottle Probe:
-PDBUFBOFNQUZXJOFCPUUMF
'JMMJUGVMMXJUISPPNUFNQFSBUVSFUBQXBUFS
1MBDFCPUUMFQSPCFTFDVSFMZJOUPCPUUMFBTTFFOJO'JHVSF
1MBDFUIFXJOFCPUUMFJOZPVSXJOFDFMMBS&OTVSFTFOTPSUJQJTGVMMZTVCNFSHFE
5PFOTVSFBDPOTJTUFOUUFNQFSBUVSFQMBDFCPUUMFQSPCFBQQSPYJNBUFMZUISFF
GFFUBXBZGSPNUIFBJSPVUQVUBOEOPUJOUIFGMPXPGUIFBJS
*UJTSFDPNNFOEFEUIBUUIFCPUUMFCFQMBDFEJOBDFOUSBMMPDBUJPOPGZPVS
XJOFDFMMBS"WPJEQVMMJOHUPPNVDIPOUIFQSPCFDPSE*UNBZCFDPNF
EJTDPOOFDUFESFTVMUJOHJOMJNJUFEGVODUJPOBMJUZPGUIFVOJU
/PUF5IFUIFSNPTUBUDBOCFTFUCFUXFFOo¡'
3FNFNCFS5IFVOJUPQFSBUFTCBTFEPOUIFUFNQFSBUVSFPGUIFXBUFS
%POPUCFNJTMFECZUIFSNPTUBUTSFBEJOHBJSUFNQFSBUVSF5IFBJSUFNQFSBUVSF
JOUIFDFMMBSXJMMCFDPPMFSUIBOUIFMJRVJEUFNQFSBUVSFPGUIFXJOFXIJMFJUJT
SFBDIJOHUIFPQUJNVNCBMBODFEUFNQFSBUVSF
'JHVSF
Page 9
08/09/21

F
CONDENSING UNIT
55°F
BOTTLE PROBE
”suctionline
” liquid line ”liquid line
18-5 THERMOSTAT
WIRE
DISPLAY CABLE
13*."3: EVAPORATOR UNIT S&$0/%"3: EVAPORATOR UNIT
DISCHARGE LOCATION DISCHARGE LOCATION
POWER CABLE POWER CABLE
*5&.4503065&#&'03&*/45"--*/(5)&&7"103"5036/*54
Route the refrigerant lines from each evaporator unit toward each other using OD copper tubing for the suction line and 1⁄4” OD
tubing for the liquid lines.
Join both suction lines together using a T-fitting. Install a ” to reducer at the outlet of theT-fitting. The remainder of the
suctionline from the T-fitting to the condensing unit will need to be ” OD copper tubing.
Join both liquid lines together using a T-fitting. Install a to 1⁄4” reducer at the inlet of the T-fitting. The remainder of the
liquidlinefrom the T-fitting to the condensing unit will need to be OD copper tubing.
Route the display cable from the desired location to the desired QSJNBSZ evaporator unit installation location
Route the bottle probe cable from the desired thermostat bottle location to desired QSJNBSZ evaporator unit installation location
Route the drain lines from a proper discharge location to desired evaporator unit installation locations
Route the power cable wiring to the desired evaporator unit installation locations.
Route an 18-5 thermostat wire between the desired evaporator unit installation locations.
55°F
TVDUJPOMJOF wTVDUJPOMJOF
20V 60Hz 1 PH 15-amp
dedicated circuit
POWER CABLE
7$0..6/*$"5*0/$"#-&
MJRVJEMJOF
Page 10
08/09/21

POWER CABLE CONDENSING UNIT
230V 60Hz 1 PH 15-amp
dedicated circuit
4VDUJPO-JOF
MJRVJEMJOF MJRVJEMJOF
24V THERMOSTAT
(NOT INCLUDED)
18-5 THERMOSTAT
WIRE
PRIMARY &7"103"503 UNIT SECONDARY EVAPORATOR UNIT
DISCHARGE LOCATION DISCHARGE LOCATION
POWER CABLE POWER CABLE
115V 60Hz 1 PH 15-amp
dedicated circuit
115V 60Hz 1 PH 15-amp
dedicated circuit
78*3*/($0//&$5*0/4&7"103"5036/*54
78JSJOH$POOFDUJPOT&WBQPSBUPS6OJUT
F
55°F
Route a standard 18-5 thermostat wire into the QSJNBSZ evaporator unit.
Locate the 18-5 thermostat wires inside of the QSJNBSZ evaporator unit.
Connect the wires according to color: yellow to yellow, red to red, green to green, and blue to blue. Connect the red
adapterwire to the end of the white thermostat wire.
Run the opposite end of the previously routed 18-5 thermostat wire to the sFDPOEBSZ evaporator unit.
Locate the 18-5 thermostat wires inside of the sFDPOEBSZ evaporator unit.
Connect the wires according to color: yellow to yellow, red to red, green to green, blue to blue, and white to white.
5IFSNPTUBU8JSJOH$POOFDUJPOT
At the thermostat terminal block, connect the wires according to color: yellow to Y, blue to C, green to G, and red to R.
Connect the opposite ends of the thermostat wires to the connections previously made between the 18-5 thermostat wire
and the QSJNBSZ evaporator unit. Connect the wires according to color: yellow to yellow, blue to blue, and green to green.
Connect the red thermostat wire to the red adapter wire previously connected to the white wire in Step 3 above.
-JRVJE-JOF
/05&5PFOTVSFDPSSFDUTZTUFN
PQFSBUJPOUIF7UIFSNPTUBU
NVTUCFQMBDFEJOTJEFUIF
XJOFDFMMBSQSFGFSBCMZJOB
DFOUSBMMPDBUJPOBXBZGSPNBOZ
BJSGMPX
7$0..6/*$5*0/$"#-&
TVDUJPOMJOF TVDUJPOMJOF
Page 11
08/09/21

1. Locate the desired installation location. Using a stud nder, locate the ceiling joists
on either side of the center point. Cut and frame 14.5” x 36” openings in the ceiling
for each evaporator unit. Make sure the framing is sucient to support the weight of
the cooling unit. Use only the mounting locations provided. These locations ensure
that the installer will not drill into any critical components within the system.
2. Determine which orientation the evaporator units will be installed in (inside the
cellar or with attic access). Mounting options are listed below:
Minimum Tools Needed:
Fully exposed mounting option
Flush mount option
Choose a mounting
option suitable
for the installation
location.
Partially recessed mounting option
Hammer Saw
#2 Phillips-head screwdriver
4&-&$5*/(.06/5*/(015*0/4
T-square
1
2
3
4
12.65”
12.65”
5.75”
6.9”
6.9”
5.75”
Page 12
08/09/21

.06/5*/(5)&&7"103"5036/*54
/05&You are REQUIRED to use only the mounting locations provided. These locations
ensure that the installer will not drill into any copper or electrical wiring within the system.
It is vital that the units be set apart and oriented so that the return air
from one unit does not recirculate into the supply air of the other unit.
/05&If installing the units without attic access, perform steps 5-2prior to steps 3-4.
1. Display cable
2. Power and thermostat wires
3. Drain line
4. Line set
Routed Items:
Line Set / Drain Line
Display, Power. and
Thermostat Wires
3. Secure the mounting bracket to the QSJNBSZ evaporator unit using the twelve (12) supplied ⁄” Phillips pan-head
screws.
4. Secure the QSJNBSZ evaporator unit’s mounting bracket to the opening using the twelve (12) supplied 21⁄2” Phillips-
head screws.
Page 13
08/09/21

'JHVSF
TOP PANEL
6. Remove the knockout(s) that you will be using to routeUIFMJOFTFUQPXFSXJSFTEJTQMBZDBCMFCPUUMF
QSPCFBOEESBJOMJOF'PSFBTFPGJOTUBMMBUJPOTFF'JHVSFGPSSFDPNNFOEFEPSJFOUBUJPOXJUIBUUJDBDDFTT
'JHVSF
ELECTRICAL
ACCESS
PANEL
*/45"--*/(5)&&7"103"503
5. Unscrew the twenty-two (22) screws and remove theUPQBOEFMFDUSJDBMBDDFTTQBOFMT
6TJOHDPQQFSUVCJOHQFSMJOFTFUTJ[JOHDIBSUSPVUFUIFMJRVJE
BOETVDUJPOMJOFTUPUIFUVCJOHDPNJOHGSPNUIFVOJU
$POOFDUUIFMJOFTFUUPTZTUFNVTJOHUIFMJOFTFUDPOOFDUJPO
JOTUSVDUJPOT
*OTVMBUFUIFTVDUJPOMJOFVTJOH"SNBGMFYPSTJNJMBSJOTVMBUJPO
3PVUFUIFESBJOMJOFPVUPGUIFQSJNBSZFWBQPSBUPSVOJUXJUIUIF
MJOFTFU$POOFDUVTJOHUIFTVQQMJFEwCBSCDPVQMJOH
$POOFDUIBSEMJOFESBJOUVCJOHUPQSPWJEFEGMFYUVCJOH
3PVUFUIFQPXFSXJSFCPUUMFQSPCFBOEEJTQMBZDBCMFUISPVHI
UIFLOPDLPVUTJOUIFFMFDUSJDBMQBOFMBTTIPXO
-*/&4&5
.06/5*/(#3"$,&5
%3"*/
-*/&
#055-&130#&
%*41-":$"#-&
,/0$,065
108&3
5)&3.045"58*3&
,/0$,065
/05& The units come in
black. The mounting brackets
and front grilles are paintable,
enabling you to match your
desired color.
Page 14
08/09/21

*/45"--*/(5)&&7"103"5036/*54
4MJEFUIFFMFDUSJDBMQBOFMVQBOEPVUPGUIFQSJNBSZFWBQPSBUPSVOJU
$POOFDUUIFHSFFOXJSFUPUIFHSFFOXJSFUIFCMBDLXJSFUPUIFCMBDLXJSFBOEUIFXIJUFXJSFUPUIFXIJUFXJSF
-PDBUFUIFUIFSNPTUBUXJSFDPOOFDUJPOTJOTJEFPGUIFQSJNBSZVOJU
$POOFDUUIFXJSFGPSUIFTFDPOEBSZVOJUBDDPSEJOHUPDPMPSZFMMPXUPZFMMPXSFEUPSFEHSFFOUPHSFFOCMVFUPCMVFBOE
XIJUFUPXIJUF
$POOFDUUIFNBMFDJSDVMBSDPOOFDUPSPOUIFCPUUMFQSPCFDBCMFUPUIFGFNBMFDJSDVMBSDPOOFDUPSPOUIFFYUFSJPSPGUIFFMFDUSJDBMCPY
$POOFDUUIFFOEPGUIFEJTQMBZDBCMFMBCFMFEi6/*5wUPUIFXJSFMBCFMFEi6/*5wDPNJOHGSPNUIFFMFDUSJDBMCPY
4MJEFUIFFMFDUSJDBMQBOFMCBDLEPXOJOUPUIFQSJNBSZFWBQPSBUPSVOJU
3FJOTUBMMUIFUPQBDDFTTQBOFMBOEGBTUFOUIFUXFOUZUXPTDSFXTJOUPQMBDF
*OTUBMMUIFTVQQMJFEUISFFJODIQJFDFTPGDPSLUBQFBSPVOEUIFEJTQMBZDBCMFCPUUMFQSPCFDBCMFBOEQPXFSXJSFT
3FQFBU4UFQTXJUIUIFTFDPOEBSZFWBQPSBUPS4UFQTBOEEPOPUBQQMZUPUIFTFDPOEBSZVOJU
UNIT
UNIT
Page 15
08/09/21

_
_
M
i
n
.
T
a
c
k
T
i
m
e
A
d
h
e
s
i
v
e
_
_
M
i
n
.
C
u
r
e
T
i
m
e
D
i
r
e
c
t
i
o
n
s
_
_
M
i
n
.
T
a
c
k
T
i
m
e
D
i
r
e
c
t
i
o
n
s
*/46-"5*0/#-"/,&5*/45"--"5*0/
1. Once mounting bracket location has been selected and installed, proceed to the insulation blanket installation.
2. Spray adhesive onto the sides of the portions of each evaporator unit and mounting bracket which protrude into
the attic. See spray adhesive directions for proper tack time before proceeding to step 3 (see illustration).
3. Wrap insulation piece (A) around the sides of each evaporator unit. Make sure the bottom edge of the insulation is
flush with the top edge of the mounting bracket (see illustration).
4. Set insulation in place by pressing firmly on all surfaces of the insulation that come in contact with the sides of
each evaporator unit (see illustration).
5. Using a utility knife, cut holes in the insulation for the line set, wiring, and drain line if needed.
6. If necessary, cut the insulation to size using the top edge of each evaporator unit as a template. Remove excess
insulation. Proceed to piece (B) installation.
*Tools required: spray adhesive, utility knife, cork tape, foil tape
If needed, trim excess insulation around all edges.
A
A
A
H
H
H
H
11.25”
14.25”
68”
Insulation Blanket
B
Insulation Blanket
B
$. blanket dimensions
C. blanket dimensions
22”
102” 35.75”
14.25”
11”
Insulation Blanket
A
Insulation Blanket
A
A
Page 16
08/09/21

*/46-"5*0/#-"/,&5*/45"--"5*0/$0/5*/6&%
8. Set piece (B) in place by pressing firmly on all surfaces of the insulation that come in contact with the top of each
evaporator unit (see illustration).
9. Using a utility knife, cut holes in the insulation for line set, wiring, and drain line if needed.
10. Once insulation is installed, apply foil tape to all seams, covering them completely.
11. Inspect insulation for damage/defects. If damaged, repair with foil tape.
12. Apply cork tape or equivalent to areas where the line set, wiring, and drain line enter the unit.
If needed, trim excess insulation around all edges.
A
_
_
M
i
n
.
T
a
c
k
T
i
m
e
A
d
h
e
s
i
v
e
_
_
M
i
n
.
C
u
r
e
T
i
m
e
D
i
r
e
c
t
i
o
n
s
_
_
M
i
n
.
T
a
c
k
T
i
m
e
D
i
r
e
c
t
i
o
n
s
B
A
B
A
7. Spray the top of each evaporator unit with spray adhesive. (See spray adhesive directions for proper tack time
before proceeding to step 8.)
Page 17
08/09/21

$POEFOTBUJPO%SBJO-JOF
5IFDPOEFOTBUJPOESBJOMJOFUVCFJTVTFEUPSFNPWFFYDFTTDPOEFOTBUJPOGSPNUIFVOJUUPBQSPQFSEJTDIBSHFMPDBUJPO*U
JTJNQPSUBOUUIBUUIFESBJOMJOFUVCFJTQSPQFSMZDPOOFDUFE
'BJMVSFUPVTFUIFDPOEFOTBUJPOESBJOMJOFUVCFXJMMWPJEUIFXBSSBOUZPOUIFVOJU
%SBJO-JOF
5IF$FJMJOH.PVOUFWBQPSBUPSVOJUGFBUVSFTBESBJOMJOFQVNQTZTUFNUIBUSFNPWFTFYDFTTJWFDPOEFOTBUFCVJMEVQJO
UIFESBJOQBO%VSJOHPQFSBUJPOUIFESBJOQBODPMMFDUTXBUFSUIBUESJQTGSPNUIFDPJM5IFESBJOMJOFQVNQTZTUFNXJMM
QSFWFOUPWFSGMPXBOEMFBLJOHCZBMMPXJOHGPSEJTDIBSHFPGUIFBEEJUJPOBMDPOEFOTBUF
$POOFDUJOHUIF%SBJO-JOF
3PVUFUIFESBJOMJOFUPBOBQQSPQSJBUFEJTDIBSHFMPDBUJPOBOEDPOOFDUUIFPQQPTJUFFOEUP
UIFUVCJOHUIBUXBTSPVUFEPVUXJUIUIFMJOFTFUVTJOHUIFQSPWJEFECBSCFEDPVQMJOHTJEFPGUIF
DPOEFOTBUFQVNQ%POPUSPVUFUIFESBJOMJOFNPSFUIBOWFSUJDBMGU
%SBJO3FDPNNFOEBUJPOT
*UJTSFDPNNFOEFEUIBUUIFMJOFDPOOFDUFEUPUIFDMFBSQMBTUJDMJOFJTBSJHJEESBJOMJOF
5IFMJOFTIPVMECFTMPQFEUPXBSETUIFEJTDIBSHFMPDBUJPOUPIFMQXJUIUIFSFNPWBMPGXBUFS
"5GJUUJOHXJUIBDBQJTSFDPNNFOEFEUPXBSETUIFDPOOFDUJPOQPJOUPGUIFUXPMJOFTUP
IFMQXJUIDMFBOJOHPVUUIFMJOFXIFOOFFEFE
830/(%SBJOMJOFJTVOEFSXBUFS
5PQSFWFOUNPMEGSPNHSPXJOHBMMPXUIF
ESBJOMJOFUPIBOHBCPWFUIFXBUFSMJOF
1/4" Clear Plastic Tubing 3JHJEESBJOMJOF
Proper Discharge
Location
%3"*/-*/&
Page 18
08/09/21
Table of contents
Other Cellar Cool Thermostat manuals
Popular Thermostat manuals by other brands

Thermogroup
Thermogroup Thermotouch 7.6iG Installation & user guide

Carrier
Carrier Comfort series owner's manual

LockStateConnect
LockStateConnect LS-90 Operation guide

Beok Controls
Beok Controls BOT-313 manual

Lux Products
Lux Products PSD011Ba Installation and operating instructions

Mars
Mars HEAT CONTROLLER IR Wireless Thermostat user manual

NuTone
NuTone NTBZ48 Installation & operation guide

XCI
XCI TSZ-1 instruction manual

White Rodgers
White Rodgers 1F80-0261 Installation and operating instructions

Energotech
Energotech EnergoControl T60 Series user guide

Lux Products
Lux Products T20-1141 Installation and operating instructions

Honeywell
Honeywell Prestige 2.0 THX9421 manual