CEM DT-102 User manual

MODEL 102
MINI DIGITAL MULTIMETER
INSTRUCTION MANUAL
IMPORTANT
Please read this instruction carefully to ensure the
safe and effective use of the tool.
FEATURES
3 1 / 2 digit LCD display
Safety designed in accordance with IEC 1010-1
over-voltage category 2.
7 functions 16 position selector.
Measures AC ／DC voltage, DC amps and
Resistance.
Battery, diode and continuity test.
Supplied complete with test leads and battery(A23)
SPECIFICATION
DC voltage: 200mV, 2V, 20V, 200V,500V
Accuracy: ＋/ －0.5%rdg＋/ －2digits
Impedance: 1M ohm
Overload protection: 500V rms.
AC voltage: 200V, 500V(40～400Hz)
Accuracy: ＋/－2.0%rdg＋/－5 digits
Impedance: 450K ohm
Overload protection: 500V rms.
Resistance: 200, 2000, 20K, 200K, 2000K ohm
Accuracy: ＋/－1.5%rdg＋/－4digits
DC current: 2mA, 200mA
Accuracy: ＋/－2.0%rdg＋/－2digits
Overload protection: f.200mA/250V fuse
Diode test: test current 1.6mA maximum
test voltage 3.2V maximum
Battery test: range 9V, test current 6mA
Continuity test: the buzzer sounds when the
resistance in a circuit to be measured is less than
about 50 ohm
WARNING:
To prevent risk of fire use only the correct fuse,
as shown above.
To avoid electric shock remove test probes
before opening. Replace cover before use.
OPERATION
WARNINGS
Before you use the instrument, inspect the test leads
and probes for damage e.g. cracks or breaks, in the
insulation. Replace if they are damaged.
Never use damaged leads/ probe.
If the voltage to be measured is not know, set the
selector switch to the highest range and reduce until
a satisfactory reading is obtained.

DC Voltage Measurement
1. Set the selector switch to the desired DCV
range.
2. Turn on the power to the circuit to be measured.
3. Connect the test leads to the circuit to be
measured. The voltage value should appear on
the digital display along with the voltage
polarity(if reversed only).
AC Voltage Measurement
1. Set the selector switch to the desired ACV
range.
2. Turn on the power to the circuit to be measured.
3. Connect the test leads to the circuit to be
measured. The voltage value will appear on the
digital display.
DC Current Measurement
1. Set the selector switch to the DCA range.
2. Open the circuit to be measured and connect the
test leads in series with the load in which
current is to be measured.
3. Turn on the power to the circuit to be measured,
the current value will appear on the digital
display.
Resistance Measurement
1. Set the selector switch to the desired OHM
range.
2. WARNING: If the resistance to be measured is
part of a circuit, turn off the power and
d ischarge all capacitors before measuremen t.
3. Connect the test leads to the circuit to be
measured.
The resistance value should now appear on the
digital display.
Diode Test
1. Set the selector switch to the diode position.
2. Connect the red test lead to the anode of the
diode to be measured and the black test lead to
the cathode.
The forward voltage drop in mV will be
displayed. If the diode is reversed, the figure 'l'
should be shown on the display.
Battery Test
1. Set the selector switch to the BATT position.
2. Connect the test leads to the battery to be
measured, the battery voltage value should
appear on the digital display.
Continuity test
1. Set the selector switch to the 'Buzzer' position.
2. Connect the test leads to the circuit or conductor
to be tested, the continuity will be judged by
whether the buzzer sound or not.
3. The buzzer sounds when the resistance in the
circuit to be measured is less then about 50
ohm.