CentoLight LIGHTBLASTER 1200WP User manual

Carefully read this manual and properly take care of it
Leggete questo manuale e conservatelo per future consultazioni
User Manual
Manuale Utente
1200W Waterproof RGBW LED Strobe & Wash Light
Faro Impermeabile Wash e Strobo a LED da 1200W RGBW
ENG
ITA
LIGHTBLASTER 1200WPLIGHTBLASTER 1200WP

Dear customer,
First of all thanks for purchasing a CENTOLIGHT® product. Our mission is to satisfy
all possible needs of light designers and professionals of entertainment lighting, by
offering a wide range of products based on the latest technologies.
We hope you will be satisfied with this fixture and, if you want to collaborate, we
are looking for a feedback from you about product operation and possible im-
provements to be introduced in the next future. Go to our website www.centolight.
com and send an e-mail with your opinion; this will help us to build equipment ever
closer to professional’s real requirements.
The CENTOLIGHT Team
Gentile Cliente,
Grazie per aver scelto un prodotto CENTOLIGHT®. La nostra missione è quella di
soddisfare ogni possibile richiesta da parte di light designers e professionisti dell’il-
luminotecnica per l’intrattenimento, offrendo una vasta gamma di apparecchiature
basate su tecnologie di ultima generazione.
Speriamo di aver soddisfatto le vostre aspettative e, se voleste collaborare, sarem-
mo lieti di ricevere un vostro feedback sulla qualità del prodotto al fine di migliorare
costantemente la nostra produzione. Visitate il nostro sito www.centolight.com ed
inviateci una mail con la vostra opinione; questo ci aiuterà a sviluppare nuovi pro-
dotti quanto più vicini alle vostre esigenze.
Il Team CENTOLIGHT

33
Eng
Table of ConTenTs
1 - Before you Start 4
1.1. What is included- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
1.2. Accessories - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
1.3. Disclaimer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
2 - Safety Instructions 5
2.1. Symbols Meaning - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5
3 - Mounting and Rigging 5
3.1. Rigging - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5
3.2. Water / Moisture - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
3.3. Heat - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
3.4. Servicing - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7
4 - Introduction 7
4.1. Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7
4.2. Product Dimensions and Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
5 - Product Setup 8
5.1. Rear Panel Description- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
5.2. Control Panel - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9
5.3. About Power Connection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10
5.4. About Dmx Connection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11
5.5. DMX Terminator - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12
5.6. 3-Pin vs 5-Pin DMX cables - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12
6 - Menu Operation 13
6.1. Functions Description - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13
7 - DMX Channel Modes 16
7.1. 7-Ch Table - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16
7.2. 18-Ch Table - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17
8 - Lux Chart 19
9 - Troubleshooting 19
10 - Specications 20
11 - Warranty And Service 21
12 - Warning 21

44
LIGHTBLASTER 1200WP User Manual
Eng
1 - before you sTarT
Thank you for purchasing LIGHTBLASTER 1200WP. Enjoy your new equipment and
make sure to read this manual carefully before operation! This user manual is made
to provide both an overview of controls, as well as information on how to use them.
1.1. What is included
Package include:
y1x CENTOLIGHT LIGHTBLASTER 1200WP Strobo & Wash Light
y1 x DMX to Ø17mm IP65 Cable
y1 x Europlug to Ø30mm IP65 Power cord
y1 x C-Bracket for floor, wall, ceiling or truss installation with 3x M10 holes.
y2 x Screw knobs
yThis User manual
ATTENTION: Packaging bag is not a toy! Keep out of reach of children!!! Keep in
a safe place the original packaging material for future use.
If anything damaged during transport, notify the shipper immediately and keep
the packing material for inspection. Again, please save the carton and all packing
materials. If the fixture must be returned to the manufacturer, it is important that it
is returned in the original manufacturer box and packing. Please do not take any
action without first contacting us.
1.2. Accessories
CENTOLIGHT can supply a wide range of quality accessories that you can use with
your LIGHTBLASTER Series equipment, like Cables, Splitters, DMX controllers, Con-
sumables, and a wide range of other fixtures.
All products in our catalogue has been long tested with this device, so we recom-
mend you to use Genuine CENTOLIGHT Accessories and Parts. Ask your CENTOLI-
GHT dealer or check out our website www.centolight.com for any accessories you
could need to ensure best performance of the product.
1.3. Disclaimer
The information and specifications contained in this User Manual are subject to
change without notice. CENTOLIGHT assumes no responsibility or liability for any
errors or omissions and reserves the right to revise or to create this manual at any
time.
Copyright© 2021 CENTOLIGHT. All rights reserved.

55
LIGHTBLASTER 1200WP User Manual
Eng
2 - safeTy InsTruCTIons
yRead these instructions
yKeep these instructions
yHeed all warning
yFollow all instructions
2.1. Symbols Meaning
The symbol is used to indicate that some hazardous live termi-
nals are involved within this apparatus, even under the normal
operating conditions, which may be sufficient to constitute the
risk of electric shock or death.
The symbol is used to describe important installation or config-
uration problems. Not following advice and information on how
to avoid such problems may lead to product malfunction.
This symbol indicates a protective grounding terminal.
WARNING: Describes precautions that should be observed to prevent the
danger of injury or death to the operator.
To protect the environment, please try to recycle packing materi-
al and exhausted consumables as much as possible.
Don’t throw this product away just as general trash, please deal
with the product follow the abandon electronic product regula-
tion in your country.
3 - MounTIng and rIggIng
Pay attention to safety! Please consider the EN 60598-2-17 and the national
standard during installation. Only authorized technicians can carry out it.
3.1. Rigging
yThe installation of the fixture has to be built and constructed in a way that it
can hold 10 times the weight for 1 hour without any harming demolition. The
installation must always be secured with a secondary safety attachment, e.g. an
appropriate catch net. This secondary safety attachment must be constructed in

66
LIGHTBLASTER 1200WP User Manual
Eng
a way that no part of the installation can fall down if the main attachment fails.
yWhen rigging, de-rigging or servicing the fixture staying in the area below the
installation place, on bridges, under high working places and other endangered
areas is forbidden. The operator has to make sure that the safety measure and
the machine’s technical installation is approved by an expert before taking into
operation for the first time and after changes before taking into operation an-
ther time. He has also to make sure that an expert approves safety measure and
the machine’s technical installation once a years.
IMPORTANT: Overhead rigging requires extensive experience, including (but not
limited to) calculating working load limits, installation material being used, and
periodic safety inspection of all installation material and the projector. If you
lack these qualications, do not attempt the installation yourself, but instead
use a professional structural rigger.
yIf the fixture shall be lowered from the ceiling or high joists, professional trussing
systems have to be used.
yIn case of installation on a wall, ceiling or truss, safety wires like LW3-76A or
LW4-76A (sold separately) and truss adapters like SLH/SQC Series (sold sepa-
rately) are required. Check www.centolight.com for further details).
yThe fixture must never be fixed swinging freely in the room.
CAUTION: Use appropriate clamps to rig the xture on the truss. Make sure that
the device is xed properly! Ensure that the structure (truss) to which you are
attaching the xtures is secure.
3.2. Water / Moisture
yThe product is for indoor use. In order to prevent risk of fire or electric shock, do
not expose to rain or moisture
yThe unit can not be used near water; for example near a bathtub, a kitchen sink,
a swimming pool, etc.
3.3. Heat
yDo not use in a confined space. Always install in a location with adequate ven-
tilation, at least 20in (50 cm) from adjacent surfaces. Be sure that no ventilation
slots on the product’s housing are blocked.
yThe unit should be located away from heat sources such as radiators, stoves or
other appliances that produce heat.
Don not use it when maximum ambient temperature is higher than 50°C. Work

77
LIGHTBLASTER 1200WP User Manual
Eng
temperature ranges from -20°C to 50°C (-4°F to 122°F).
3.4.Servicing
yDo not implement any servicing other than those means described in the man-
ual. Refer all servicing to qualified service personnel only. The internal compo-
nents of the equipment must be purchased from the manufacturer. Only use
accessories/attachments or parts recommended by the manufacturer.
4 - InTroduCTIon
LGIHTBLASTER 1200WP is a LED strobe and wash light designed for outdoor appli-
cations where, in addition to power and safety, also versatility is important.
The light source is based on 1200x1W RGBW 4in1 high brightness LEDs. The emis-
sion surface is split into 5 independent zones. It is possible to control the individual
colors of each zone via DMX, or simplify the number of channels for basic strobe/
wash application.
The die-cast aluminum housing is waterproof, and provides IP65 protection for out-
door use. The LIGHTBLASTER 1200WP is totally noiseless, thanks to the convection
cooling system without any fans.
It is specifically designed for both indoor and outdoor silent environments, like
theaters, houses of worship or live stages with soft music. Waterproof Input and
Output connections ensure maximum safety in any environment.
4.1. Features
y1200pcs 1W High-Brightness RGBW 4in1 LED
y120° Beam Angle
y5 Independent Zones
yStrobe from 0 to 30Hz
yBuilt-in Strobe, Color Mixing and Auto effects
yDMX512/Manual/Master-Slave/Sound Control Modes
ySelectable 7 and 18 DMX Channel Modes
yBuilt-in Auto Programs and Preset Colors for easy use, even without DMX con-
troller
yConvection Cooling System, without Fan (completely Noiseless)
yWaterproof Power In/Out and DMX In/Out Connections
yEasy-to-use Front Panel with 4-digit Led Display

88
LIGHTBLASTER 1200WP User Manual
Eng
4.2.Product Dimensions and Overview
599 mm (23.58”)
592 mm (23.30”)
100 mm
(3.94”)
262 mm
(10.31”)
5 - ProduCT seTuP
5.1. Rear Panel Description
1
2
3
5
4
1) DMX Input (Male Plug)
DMX Input to be connected to a DMX controller or to previous fixture in case of
daisy-chain.
2) Power Supply Input Plug
Plug the power-cord included with LIGHTBLASTER 1200WP into an AC socket prop-
erly configured for this fixture. Please read “5.3. About Power Connection” on page
10 for details on internal wiring.

99
LIGHTBLASTER 1200WP User Manual
Eng
3) Control Panel
This panel section has a 4x 7-segment LED display and 4 buttons to control all de-
vice functions. Please check next paragraph
4) Power Output Plug
This fixture is equipped with an output power connector to be used as power mains
source in case of daisy-chain connection up to a maximum of 3 fixtures.
1st Unit 3rd Unit2nd Unit
Mains Input
100-240Vac - 50/60Hz
5) DMX OUTPUT (FEMALE PLUG)
DMX Output to be connected to next fixture in case of daisy-chain.
5.2. Control Panel
5
14
2 3
1) MENU/ESC Button
This button allows to put in stand-by the control panel or escape from a function
without any saving.
2) UP Button
Using this button, it is possible to scroll-up the device’s functions and increase the
function’s value.
3) DOWN Button
Using this button, it is possible to scroll-down the device’s functions and decrease
the function’s value.
4) ENTER Button
This button allows to save a new function’s value.

1010
LIGHTBLASTER 1200WP User Manual
Eng
5) 4 x 7-Segment Display
It shows the current function name or value.
5.3. About Power Connection
yAlways make sure that the voltage of the outlet you are connecting the product
to is within the range stated in paragraph “10 - Specifications” on page 20
or rear panel of the product (AC110V-240V 50/60Hz).
yMake sure the power cord is not crimped or damaged. Never connect this prod-
uct to a dimmer pack or rheostat.
yNever disconnect the product from power cord by pulling or tugging on the cord.
yTo avoid electric shock, all fixtures must be connected to circuits with a suitable
ground and circuit breaker.
yWire correspondence is as follows:
Cable (EU) Pin International
Brown Live L
Blue Neutral N
Yellow/Green Earth
Earth must be connected! Always pay attention to safety! Before taking into
operation for the rst time, the installation has to be approved by an expert.
1) Waterproof Power Cables
Since the LIGHTBLASTER 1200WP is a strobo/washer fixture with IP65 protection
degree, it is equipped with waterproof In-Out DMX connections.
Your strobo is equipped with a power adapter cable
of about 1m length, with a Europlug (Schuko) connec-
tor and a Ø30mm Waterproof connector. This adapt-
er cable allows you to connect the unit to mains.
30mm
1.18” ca. If you need extension cables for installing your
LIGHTBLASTER 1200WP, especially in case of multiple
installations, you may need to buy extensions with
connections like the one on left.
SKU Item Name Length
L760L WEC-30POWER-03 3m

1111
LIGHTBLASTER 1200WP User Manual
Eng
Please ask further information to your authorized Centolight dealer or check www.
centolight.com.
5.4.About Dmx Connection
When use a DMX controller, please make sure that there is no interference
sources (e.g. intercom, high frequency radio waves and radiation source).
DMX machines are designed to receive data through a serial Daisy Chain. A Daisy
Chain connection is where the DATA OUT of one fixture connects to the DATA IN of
the next fixture. The order in which the machines are connected is not important
and has no effect on how a controller communicates to each of them. Use an order
that provides for the easiest and most direct cabling.
DMX Terminator
Unit 1 Unit 2 Last Unit
DMX 512
3-Pin XLR
Pin 1: GND
Pin 2: DMX -
Pin 3: DMX +
OUTPUTINPUT
DMX use of 3-Pin XLR Connectors
Connect machines using shielded 2-conductor twisted pair cable with 3-pin XLR
male to female connectors. The shield connection is pin 1, while pin 2 is Data Nega-
tive (S-), and pin 3 is Data positive (S+).
CAUTION: Wires must not come into contact with each other; otherwise the x-
tures will not work at all, or will not work properly.
1) Waterproof DMX Cables
Since the LIGHTBLASTER 1200WP is a strobo/washer fixture with IP65 protection
degree, it is equipped with waterproof In-Out DMX connections.
Your strobo is equipped with a DMX adapter cable
of about 1m length, with a 3-pin XLR male connector
and a Ø17mm Waterproof connector. This adapter
cable allows you to connect the unit to a DMX con-
troller.

1212
LIGHTBLASTER 1200WP User Manual
Eng
17mm
0.67” ca.
If you need extension cables for installing your
LIGHTBLASTER 1200WP, especially in case of multiple
installations, you may need to buy extensions with
connections like the one on left.
SKU Item Name Length
L757L WEC-17DMX-03 3m
Please ask further information to your authorized Centolight dealer or check www.
centolight.com.
5.5. DMX Terminator
120ohm, 1/4W
Resistor
DMX Terminator
DMX is a resilient communication protocol, however errors still
occasionally occur. In order to prevent electrical noise from dis-
turbing and corrupting the DMX control signals, a good habit is to
connect DMX output of last fixture in the chain to a DMX termina-
tor, especially over long signal cable runs.
The DMX terminator is simply an XLR connector with a 120Ω
(ohm), 1/4 Watt resistor connected across Signal (-) and Signal (+),
respectively, pins 2 and 3, which is then plugged into the output
socket on last projector in the chain. The connections are illustrat-
ed below.
Complimentary signal cable can transmits signals to 20 unit xtures at most.
Signal amplier is a must to connect more xtures.
5.6. 3-Pin vs 5-Pin DMX cables
DMX connection protocols used by controllers and fixtures manufacturers are not
standardized around the world. However, two are the most common standards:
5-Pin XLR and 3-Pin XLR system. If you wish to connect this fixture to a 5-Pin XLR in-
put fixture, you need to use an adapter-cable or make it by yourself. Below you can
see the wiring correspondence between 3-Pin and 5-Pin plug and socket standards
5-Pins XLR (plug)
Pin 1: GND (Screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-Pins XLR (socket)
Pin 1: GND (Screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-Pins XLR (socket)
Pin 1: GND (Screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-Pins XLR (plug)
Pin 1: GND (Screen)
Pin 2: Signal (-)
Pin 3: Signal (+)

1313
LIGHTBLASTER 1200WP User Manual
Eng
6 - Menu oPeraTIon
All LIGHTBLASTER 1200WP functions are selectable by using the UP button and
DOWN button on the Control Panel as described in “5.2. Control Panel” on page
9. Below is an explanation of the all functions.
6.1. Functions Description
1) DMX Channel Selection
After the selection of function, by pressing ENTER button, it is possible to se-
lect the desired DMX Channel in order to control the device by using a DMX control-
ler. Once the desired channel is selected, press the ENTER button to confirm.
The range of this parameter is A001 → A512.
2) Reset
This parameter can be On or Off. The parameter name on the display is .
When this parameter is set to On, the device is reset.
Note: During parameter settings, if no operations are performed within 30
seconds, the device will return to display the rst function of main menu
(DMX Address).
3) Device Information
By selecting the function , you will get general information about the device
status as follows:
Device Usage Time : Displays usage time in hours.
Device Software Version : Shows software version.
Device Temperature :Displays the internal temperature in °Celsius.
4) Manual Mode
menu allows you to manually adjust all setting. Press [ENTER] to access the
menu, then press [UP]/ DOWN] to browse the list of parameters, and finally [ENTER]
to adjust the specific parameter value. Now use [UP]/[DOWN] again to increase/de-
crease its value. Press then [ENTER] again to confirm the change. Press [MENU/ESC]
button to exit the change without modification. Below a detailed description
Parameter N° Function Value Effect
CH01 Main Dimmer 0 ÷ 4 Shutdown
5 ÷ 255 Linear dimming from dark to light

1414
LIGHTBLASTER 1200WP User Manual
Eng
CH02 Strobe 0 ÷ 4 Shutdown
5 ÷ 54 Random strobe
CH02 Strobe
55 ÷ 104 Fade in strobe
105 ÷ 154 Fade out strobe
155 ÷ 204 Pulse strobe
205 ÷ 255 Normal strobe
CH03 Strobe Speed 0 ÷ 255 Slow to fast
CH04 Red dimming 0 ÷ 255 Red dimming goes from dark to bright
CH05 Green dimming 0 ÷ 255 Green dimming goes from dark to bright
CH06 Blue dimming 0 ÷ 255 Blue dimming goes from dark to bright
CH07 White dimming 0 ÷ 255 White dimming goes from dark to bright
CH08 Color wheel
mode
0 ÷ 4 No function
5 ÷ 14 Red
15 ÷ 24 Green
25 ÷ 34 Blue
35 ÷ 44 Yellow
45 ÷ 54 Cyan
55 ÷ 64 Magenta
65 ÷ 74 White
75 ÷ 199 Color skip from slow to fast
200 ÷ 255 Random colors from slow to fast
CH09 Color Fade
0 ÷ 7 No function
8 ÷ 39 Red to Yellow
40 ÷ 71 Yellow to Green
72 ÷103 Green to Cyan
104 ÷135 Cyan to Blue
136 ÷167 Blue to Magenta
168 ÷199 Magenta to Red
200 ÷ 255 Color fade from slow to fast
CH10 Built-In Effect
0 ÷ 4 No function
5 ÷ 34 Effect 1
35 ÷ 69 Effect 2
70 ÷104 Effect 3
105 ÷139 Effect 4
140 ÷ 174 Effect 5

1515
LIGHTBLASTER 1200WP User Manual
Eng
CH10 Built-In Effect 175 ÷ 209 Effect 6
210 ÷ 255 Effect 7
CH11 Effect speed 0 ÷ 255 Slow to fast
CH12 Effect Shade 0 ÷ 255 Effect Shade
CH13 Effect of red 0 ÷ 255 Red effect dimming from dark to bright
CH14 Effect of green 0 ÷ 255 Green effect dimming from dark to bright
CH15 Effect of blue 0 ÷ 255 Blue effect dimming from dark to bright
CH16 Effect of white 0 ÷ 255 White effect dimming from dark to bright
CH17 Dimming Effect 0 ÷ 255 Total effect dimming from dark to bright
CH18 Background
Total Dimmer 0 ÷ 255 Backlight total dimming from dark to bright
5) TOOL Menu
This menu contains some utilities. The display shows . By pressing [ENTER]
button, you can access the list of functions. You can then browse by using [UP]/
[DOWN] buttons and confirm with [ENTER] button again.
White balance adjustment
This sub-menu contains the parameters related to color balance.
White balance switch
It can be On or Off. White balance sub-menu is available only when this
feature is set to On. Default value is Off. The display shows . Use the [UP]/
[DOWN] buttons to set On or Off and then press the [ENTER] button to confirm
the setting.
Red, Green, Blue, White
These parameters are used to adjust, respectively, the Red ,Green, Blue and
White color brightness from dark to bright. The range is 50 ÷255 and the de-
fault value is 255. By using [UP]/[DOWN] buttons you can increases/decreases
their value. Then press [ENTER] to confirm. Press [MENU/ESC] button to exit
without modification. Their names are: ,
,
,
.
Non-Signal Reset
The display shows , it can be set to On or Off and the default setting is Off.
On
When this parameter is set to On, the light stays working and commands re-
main even when DMX cables between controller and fixture are disconnected.
Off
When this parameter is set to Off, all signals will be cleared and light will be
off when the DMX connection between controller and fixture is removed.

1616
LIGHTBLASTER 1200WP User Manual
Eng
Default Setting
This parameter can be set to On or Off and its name on the display is .
When it is set to On, the device restores the default settings.
6) DMX Channels Number Conguration
LIGHTBLASTER 1200WP can be configured with two channel modes by setting
function. The two options are 7-Ch and 18-Ch. Press the ENTER button to
confirm the selected mode.
NOTE: If the device is not connected to a DMX controller, the main screen will
blink. By pressing [ENTER] button, the device will access main menu.
7) Run Mode Selection
After the selection of function with [UP] and/or [DOWN] buttons, press EN-
TER button to select the device Run Mode:
• AUTO Mode: The device automatically run according to built-in program.
The display shows .
• SOUND Mode: If the Sound Mode is selected and the integrated microphone
detects sounds, the device will run automatically according to
the built-in program. The display shows .
• SLAVE Mode: Using this mode, it is possible to connect several units togeth-
er and operate them all together. Use IP-65 DMX cables to
connect two or more units together from the DMX OUT to the
DMX IN port. The first unit in the chain is the MASTER, all the
rest of units have to be set as SLAVE. The display shows
. Set the Master unit in AUTO Mode or SOUND Mode to oper-
ate all the units in the chain.
7 - dMX Channel Modes
This device has two DMX channel modes (7CH and 18CH). To see how to change
channel mode, please refer to “6) DMX Channels Number Configuration” on page
16.
7.1. 7-Ch Table
Channel Function Value Effect
CH1 Dimmer 0 ÷ 4 Shutdown
5 ÷ 255 Linear dimming from dark to light
CH2 Strobe 0 ÷ 4 Shutdown
5 ÷ 54 Random strobe

1717
LIGHTBLASTER 1200WP User Manual
Eng
CH2 Strobe 55 ÷ 104 Fade in strobe
CH2 Strobe
105 ÷ 154 Fade out strobe
155 ÷ 204 Pulse strobe
205 ÷ 255 Normal strobe
CH3 Strobe Speed 0 ÷ 255 Slow to fast
CH4 Red dimming 0 ÷ 255 Red dimming goes from dark to bright
CH5 Green dimming 0 ÷ 255 Green dimming goes from dark to bright
CH6 Blue dimming 0 ÷ 255 Blue dimming goes from dark to bright
CH7 White dimming 0 ÷ 255 White dimming goes from dark to bright
7.2. 18-Ch Table
Channel Function Value Effect
CH1 Main Dimmer 0 ÷ 4 Shutdown
5 ÷ 255 Linear dimming from dark to light
CH2 Strobe
0 ÷ 4 Shutdown
5 ÷ 54 Random strobe
55 ÷ 104 Fade in strobe
105 ÷ 154 Fade out strobe
155 ÷ 204 Pulse strobe
205 ÷ 255 Normal strobe
CH3 Strobe Speed 0 ÷ 255 Slow to fast
CH4 Red dimming 0 ÷ 255 Red dimming goes from dark to bright
CH5 Green dimming 0 ÷ 255 Green dimming goes from dark to bright
CH6 Blue dimming 0 ÷ 255 Blue dimming goes from dark to bright
CH7 White dimming 0 ÷ 255 White dimming goes from dark to bright
CH8 Color-Change
mode
0 ÷ 4 No function
5 ÷ 14 Red
15 ÷ 24 Green
25 ÷ 34 Blue
35 ÷ 44 Yellow
45 ÷ 54 Cyan
55 ÷ 64 Magenta
65 ÷ 74 White
75 ÷ 199 Color skip from slow to fast
200 ÷ 255 Random colors from slow to fast

1818
LIGHTBLASTER 1200WP User Manual
Eng
CH9 Color Fade
0 ÷ 7 No function
8 ÷ 39 Red to Yellow
40 ÷ 71 Yellow to Green
72 ÷103 Green to Cyan
104 ÷135 Cyan to Blue
136 ÷167 Blue to Magenta
168 ÷199 Magenta to Red
200 ÷ 255 Color fade from slow to fast
CH10 Built-In Effect
0 ÷ 4 No function
5 ÷ 34 Effect 1
35 ÷ 69 Effect 2
70 ÷104 Effect 3
105 ÷139 Effect 4
140 ÷ 174 Effect 5
175 ÷ 209 Effect 6
210 ÷ 255 Effect 7
CH11 Effect speed 0 ÷ 255 Slow to fast
CH12 Effect Shade 0 ÷ 255 Effect Shade
CH13 Effect of red 0 ÷ 255 Red effect dimming from dark to bright
CH14 Effect of green 0 ÷ 255 Green effect dimming from dark to bright
CH15 Effect of blue 0 ÷ 255 Blue effect dimming from dark to bright
CH16 Effect of white 0 ÷ 255 White effect dimming from dark to bright
CH17 Dimming Effect 0 ÷ 255 Total effect dimming from dark to bright
CH18 Background total
dimmer 0 ÷ 255 Backlight total dimming from dark to bright

1919
LIGHTBLASTER 1200WP User Manual
Eng
8 - luX CharT
Diameter (cm):
Distance (m):
Lux (White):
346 1039 24100
1 3 70
4054 485 84
120°
692
2
988
1732
5
180
3300
10
57
9 - TroubleshooTIng
Problem Probable Cause(s) Remedy
No response from fixture
when power is applies No power to fixture Check power cables
Check mains plug
Fixture does not reset
correctly Electronic failure Contact service technician*
No light, LED cuts out
intermittently, or burns out
too quickly
LED missing or blown Disconnect fixture and replace
the LED
Fixture or LED is too hot Allow fixture to cool. If prob- lem persists, contact service
technician*
Fixture resets but does
not respond correctly to
controller (DMX mode
operation)
Controller not connected Connect controller
Incorrect addressing of the
fixtures Check address setting on fixture and controller
Bad data link connection Inspect cables and correct poor connections and/or broken
cables.
Conflict between tracking
and vector control Eliminate scene cross-fade on controller
Data link not terminated Insert termination plug in output
of last fixture**
Defective fixture on 2 devices
transmitting on link
Bypass fixtures one at a time
until normal operation is
regained: unplug both connec-
tors and connect them directly
together
Colors cannot be mixed Random color mixing is on Turn off random color mixing
* To contact CentoLight service, see “11 - Warranty And Service” on page 21 or visit www.centolight.com
** For instruction on how to install a DMX terminator, see “5.5. DMX Terminator” on page 12.

2020
LIGHTBLASTER 1200WP User Manual
Eng
10 - sPeCIfICaTIons
Led source 1200x SMD5054 1W (RGBW 4in1)
Bram Angle 120°
Lux (White only) 4054 @1m, 988 @ 2m, 150 @ 5m
Color Temperature (CCT) 6000-6500K (white)
CRI ≥80
Zones 5
Flicker Free Yes
Dimmer 0÷100% 16-bit Control
Strobe From 0Hz to 30Hz
DMX Channel Modes 7/18CH
Control Modes DMX512/Auto/Master-Slave/Sound Active
Control Panel 4-digit LED Display and 4 Buttons
DMX Connections IP65 3-pin In/Out - Ø17mm
Power Connections IP65 3-pin In/Out - Ø30mm
Cooling Convection Cooling without fan
Noise Noiseless (no fan)
IP Grade IP65
Voltage AC110V-240V
Frequency 50/60Hz
Power Consumption 600W (Average) / 1200W (Peak)
Fixture Size (WxDxH) (Max) 599 x 100 x 262 mm (23.58 x 3.94 x 10.31 in)
Fixture Weight 11 kg (24.25 lbs.)
Carton Size (WxDxH) 680 x 325 x 200 mm (26.77 x 12.79 x 7.87 in)
Carton Weight 12 kg (26.45 lbs.)
Note: Our products are subject to a process of continual further development. Therefore modifications to
the technical features remain subject to change without further notice.