Central Pneumatic 95218 Parts list manual

NAILER/STAPLER
OIL FREE - 18 GAUGE
Model 95218
ASSEMBLY AND OPERATION INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND
ALL WARNINGS AND INSTRUCTIONS BEFORE USE.
Copyright©2006 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.

SKU 95218 For technical questions, please call 1-800-444-3353 PAGE 2
PRODUCT SPECIFICATIONS
Fastener Capacity 18 Gauge (5/8” – 2” Brads) / (5/8” – 1-5/8” Staples)
1/4” Crown
Magazine Capacity 100 Fasteners
Load Style Top Loading Magazine
Operating PSI 125 PSI Maximum*
Average Air Flow 3.0 CFM
Air Inlet Size 1/4”-18 NPT
Safety Trigger Mechanism Single Sequential
Accessories Hex Wrenches (Qty. 2)
Weight 3.15 Pounds
*The air pressure setting must not exceed job site regulations/restrictions. The air pressure setting must
not exceed 90 PSI when being used with work pieces that have a thickness of less than 1-3/4”.
SAVE THIS MANUAL
You will need this manual for the safety warnings and precautions, assembly, oper-
ating, inspection, maintenance and cleaning procedures, parts list and assembly diagram.
Keep your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep this manual and invoice in a safe and dry place for future reference.
SAFETY WARNINGS AND PRECAUTIONS
WARNING: When using tool, basic safety precautions should always be fol-
lowed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or power tools in damp or
wet locations. Do not expose to rain. Keep work area well lit. Do not use electri-
cally powered tools in the presence of ammable gases or liquids.
3. Keep children away. Children must never be allowed in the work area. Do not let
them handle machines, tools, extension cords, or air hoses.
4. Store idle equipment. When not in use, tools must be stored in a dry location to
inhibit rust. Always lock up tools and keep out of reach of children.
5. Use the right tool for the job. Do not attempt to force a small tool or attachment
to do the work of a larger industrial tool. There are certain applications for which
this tool was designed. It will do the job better and more safely at the rate for which
it was intended. Do not modify this tool, and do not use this tool for a purpose for
which it was not intended.

SKU 95218 For technical questions, please call 1-800-444-3353 PAGE 3
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in mov-
ing parts. Protective, electrically non-conductive clothes and non-skid foot-wear are
recommended when working. Wear restrictive hair covering to contain long hair.
7. Do not overreach. Keep proper footing and balance at all times. Do not reach
over or across running machines or air hoses.
8. Use eye and ear protection. Always wear ANSI-approved impact
safety goggles and appropriate hearing protection. Wear a full face shield
if you are producing metal lings or wood chips. Wear a NIOSH-approved
dust mask or respirator when working around metal, wood, and chemi-
cal dusts and mists. Other people in the work area must also wear ANSI approved
impact safety goggles.
9. Maintain tools with care. Keep tools clean for better and safer performance. Fol-
low instructions for lubricating and changing accessories. Inspect tool cords and
air hoses periodically and, if damaged, have them repaired by a qualied techni-
cian. The handle must be kept clean, dry, and free from oil and grease at all times.
Do not operate a tool if any portion of the tool’s operating controls are inoperable,
disconnected, altered, or not working properly.
10. Disconnect air hose and release any built-up air pressure. Never service the
Nailer, clear jams, or disassemble with the air hose attached. Always release any
built-up air even after disconnecting hose. Disconnect the Nailer when not in use.
11. Remove adjusting wrenches. Check that adjusting wrenches are removed from
the tool or machine work surface before attaching to an air source.
12. Avoid unintentional starting. Be sure the trigger is in the OFF position when not
in use and before plugging in. Do not carry any tool with your nger on the trigger,
whether it is attached to an air source or not. Do not point the tool towards yourself
or anyone whether it contains brads or not.
13. Stay alert. Watch what you are doing. Use common sense. Do not operate any
tool when you are tired.
14. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform
its intended function. Check for alignment and binding of moving parts, any broken
parts or mounting xtures, and any other condition that may affect proper operation.
Any part that is damaged should be properly repaired or replaced by a qualied
technician. Do not use the tool if the trigger does not operate properly.
15. Replacement parts and accessories. This product is to be repaired and serviced
only by a qualied technician. When this product is serviced, only identical replace-
ment parts should be used. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Approved accessories are available
from Harbor Freight Tools.

SKU 95218 For technical questions, please call 1-800-444-3353 PAGE 4
16. Do not operate tool if under the inuence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgement or reexes are
impaired while taking drugs. If there is any doubt, do not operate the tool.
17. Use proper size and type extension cord for an air compressor. If an exten-
sion cord is required, it must be of the proper size and type to supply the correct
current to the compressor without heating up. Otherwise, the extension cord could
melt and catch re, or cause electrical damage to the compressor. Check your air
compressor’s manual for the appropriate size cord. It is also possible that the use
of an extension cord may cause your circuit breaker to trip or your panel fuse to
break. If this happens, either use the compressor without an extension cord or nd
a larger amperage circuit to use.
18. Maintenance. The maintenance outlined in the “Maintenance” section should be
performed regularly. For your safety, this product should be serviced or repaired
regularly only by a qualied technician.
19. Compressed air only. Use clean, dry, regulated, compressed air at between 90
and 125 PSI. Never use oxygen, carbon dioxide, combustible gases, or any other
bottled gases a power source for this tool.
20. Do not load brads or staples with the trigger or safety depressed. Uninten-
tional ring may occur. Do not load brads when the air hose is connected to the
tool. Always assume the tool contains brads or staples.
21. Disconnect air supply before loading this tool. Before reloading (or making any
adjustments to) the tool, make sure the compressed air is disconnected.
22. Fire brads and staples into an appropriate work surface only. Do not attempt
to re brads or staples into surfaces too hard to penetrate. Do not drive brads or
staples on top of other brads or staples, or at too steep an angle. Brads and staples
can ricochet, causing personal injury. Never re this tool into the air, or point it toward
yourself or another person. Always wear ANSI-approved impact safety goggles
during use, maintenance, and reloading.
23. Do not re brads or staples too close to the edge of a workpiece.
They may split the workpiece and y free, causing personal injury.
24. Take caution, as some woods contain preservatives such as copper
chromium arsenate (CCA) which can be toxic. When nailing these materials
extra care should be taken to avoid inhalation and minimize skin contact.
25. WARNING: Some dust created by power sanding, sawing, grinding, drilling,
and other construction activities, contains chemicals known [to the State of
California] to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
Lead from lead-based paints

SKU 95218 For technical questions, please call 1-800-444-3353 PAGE 5
Crystalline silica from bricks and cement or other masonry products
Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area,
and work with approved safety equipment, such as those dust masks that are spe-
cially designed to lter out microscopic particles. (California Health & Safety Code
§ 25249.5, et seq.)
26. Stay within air pressure capacity. Never operate the tool above 125 PSI.
27. Hold tool away from head and body. During operation the tool may kickback,
causing injury.
28. Transport this tool safely. Always disconnect air supply when moving the tool in
the workplace. Carry the tool by the handle to avoid contact with the trigger.
29. Avoid working alone. If an accident happens, an assistant can bring help.
30. WARNING: The warnings, cautions, and instructions discussed in this instruc-
tion manual cannot cover all possible conditions and situations that may occur.
It must be understood by the operator that common sense and caution are factors
which cannot be built into this product, but must be supplied by the operator.
Note: Performance of the compressor (if powered by line voltage) may vary depending
on variations in local line voltage. Extension cord usage may also affect the tool
performance.
UNPACKING
When unpacking, check to make sure that all accessories listed on page 11 are
included, and the product is intact and undamaged. If any parts are missing or broken,
please call Harbor Freight Tools at the number shown on the cover of this manual as
soon as possible.
AIR SUPPLY SETUP
For best service, you should incorporate a regulator and an in-line lter as shown
in the diagram below. Hoses, couplers, regulators, and lters are all available from Harbor
Freight Tools.
AIR
COMPRESSOR
AIR
FILTER
REGULATOR
TO
NAILER/STAPLER

SKU 95218 For technical questions, please call 1-800-444-3353 PAGE 6
TESTING THE SINGLE SEQUENTIAL SAFETY TRIP MECHANISM
WARNING: Even though the Nailer should be empty during this procedure, ALWAYS point
the Nailer at a piece of scrap wood when testing. Always wear ANSI-approved
safety goggles.
1. Make sure the tool is disconnected from its air supply.
2. Completely empty the Moveable Magazine (61) of Brads or Staples.
3.
DRIVER GUIDE (62)
TRIGGER
(32)
MOVEABLE MAGAZINE
(61)
AIR INLET PLUG
(78)
FIXED LEVER (53)
The Nailer/Stapler should not re if the Driver Guide (62) is not depressed against
the workpiece.
4. Make sure the Trigger (32) and Driver Guide (62) move freely, without sticking.
5. Connect the air supply to the tool at the Air Inlet Plug (78). Set the regulator at
the recommended 90 to 125 operating PSI. Do not exceed the maximum 125
PSI.
6. Test the tool by depressing the Driver Guide (62) against the workpiece without
pulling the Trigger (32). The tool must not cycle (re). If it cycles (res), stop
immediately and have it repaired by a qualied service technician.
7. Hold the tool away or off the workpiece. The Driver Guide (62) of the tool should
return to its original position. Squeeze the Trigger (32). The tool should not cycle
(re). If the tool cycles (res), stop immediately and have it repaired by a qualied
service technician.
8. Depress the Driver Guide (62) against the workpiece and squeeze the Trigger (32).
The tool must cycle (re) only once. Release the Trigger and squeeze it again.
The tool must cycle (re) only once. With the Trigger held, carefully lift the Nailer
and press it against the workpiece again. The tool must not cycle (re). If it fails
to perform in the manner explained in bold, have it repaired by a qualied service
technician.

SKU 95218 For technical questions, please call 1-800-444-3353 PAGE 7
LOADING BRADS AND STAPLES
WARNING: Always wear ANSI-approved impact safety goggles when us-
ing, reloading, or performing any other maintenance on this tool. Other
people in the work area must also wear ANSI-approved impact safety gog-
gles.
Note: Do not mix brads and staples. Load the magazine with only one type.
1. Lift the Fixed Lever (53) and slide the Moveable Magazine (61) back until it locks
in place.
2.
FIXED LEVER (53)
MOVEABLE MAGAZINE (61)
LOAD
BRADS OR STAPLES
HERE.
AIR INLET PLUG
(78)
TRIGGER
(32)
DRIVER GUIDE (62)
Place a full clip of the desired size Brads (5/8” to 2”) or Staples (5/8” to 1-5/8”) in
the Moveable Magazine (61). Up to 100 Brads or Staples may be loaded in front
of the Moveable Magazine.
3. Slide the Moveable Magazine (61) forward, making sure the Fixed Lever (53) locks
in place.

SKU 95218 For technical questions, please call 1-800-444-3353 PAGE 8
OPERATING THE NAILER/STAPLER
1. Attach the Nailer/Stapler to the air supply at the Air Inlet Plug (78). Start your com-
pressor and check the pressure, making sure it is set no higher than 125 PSI.
Do not exceed the maximum 125 PSI.
2. Rotate the Air Deector (3) so that the exhaust air blast will be directed away from
the operator.
3. To re, place the Driver Guide (62) of the tool on the workpiece. The Nailer/Stapler
should not re if the Driver Guide is not depressed. Once depressed, gently and
briey squeeze the Trigger (32) once; one Brad/Staple will be red.
4. Allow the tool to do the work. Tool should be held rmly against work surface, or
the fastener may not be driven deeply enough. Always allow the tool to recoil off
the work surface. Be careful not to nail or staple over another nail or staple.
5.
DRIVER GUIDE (62)
AIR INLET PLUG
(78)
TRIGGER
(32)
FIXED LEVER (53)
AIR DEFLECTOR (3)
MOVEABLE MAGAZINE (61)
When nished using the Nailer/Stapler, always disconnect the tool from its air sup-
ply. Empty the Movable Magazine (61) completely of Brads/Staples. Attempt to re
the tool into a piece of scrap wood to ensure it is disconnected and is incapable of
ring any Brads/Staples.
6. Make sure to store the Nailer/Stapler in a clean, dry, safe location out of reach of
children.

SKU 95218 For technical questions, please call 1-800-444-3353 PAGE 9
Anytime any maintenance or repairs are done (including clearing jams), FIRST:
1. Disconnect the Nailer/Stapler from its air supply.
2. Empty the Moveable Magazine (61) completely.
3. Attempt to re the Nailer into a piece of scrap wood to ensure that it is disconnected
and is incapable of ring any Brads/Staples.
4. Wear ANSI-approved safety goggles, if not already doing so.
CLEARING JAMS
Use eye and ear protection when clearing jams. Always wear ANSI-
approved impact safety goggles and appropriate hearing protection.
1. Occasionally, a Brad/Staple may become jammed in the ring mechanism of the
Nailer/Stapler, making the tool inoperable.
2. To remove a jammed Brad/Staple, disconnect the tool from its air supply, lift the
Fixed Lever (53) and slide the Moveable Magazine (61) back until it locks in place.
Then, lean the Nailer/Stapler back.
3. Remove all Brads/Staples from the Moveable Magazine (61). Then press the Fixed
Lever (53) and slide the Moveable Magazine (61) forward all the way, making sure
it locks in place.
4. Attempt to re the Nailer/Stapler into a piece of scrap wood to ensure it is discon-
nected and is incapable of ring any Brads/Staples.
5. With the Driver Guide (62) facing away from you, remove the three Bolts (65). Then
remove the Safety Cover (66) and Driver Guide Cover (67) to expose the Driver
Guide (62).
6. Remove the jammed Brad/Staple. Then replace the Driver Guide Cover (67), Safety
Cover (66), and three Bolts (65).
7. Reload the tool with Brads/Staples. Then, reconnect the air supply hose to the
tool.
8. Press the Driver Guide (62) against a piece of scrap wood, and test re the Nailer/
Stapler several times while checking for proper operation. If the tool is properly ring,
you may continue using the tool. If the tool fails to perform properly, immediately
discontinue use and have the tool repaired by a qualied service technician.
9. When nished working, disconnect the air supply. Remove the Brads/Staples. Then,
store the tool in a clean, dry, safe location out of reach of children.

SKU 95218 For technical questions, please call 1-800-444-3353 PAGE 10
Anytime any maintenance or repairs are done (including clearing jams), FIRST:
1. Disconnect the Nailer/Stapler from its air supply.
2. Empty the Moveable Magazine (61) completely.
3. Attempt to re the Nailer into a piece of scrap wood to ensure that it is disconnected
and is incapable of ring any Brads/Staples.
4. Wear ANSI-approved safety goggles, if not already doing so.
INSPECTION, MAINTENANCE, AND CLEANING
1. Inspect the air supply Screen that is located in the End Cap (77) before each use,
and clean or replace as necessary. Dirt and water in the air supply Screen are
major causes of pneumatic tool wear. Use a lter in the compressed air system for
better performance and longer tool life. The lter must have adequate ow capacity
for the specic application.
2. Clean the external parts of the Nailer/Stapler with a clean cloth and mild detergent
or non-ammable solvent. Then, dry.
3. Store the tool in a clean, dry, safe location out of reach of children.
4. WARNING: All maintenance, service, or repairs not listed in this manual are
only to be attempted by a qualied service technician.
TROUBLESHOOTING
Problem Possible Solution
Air leak near top of tool. 1. Tighten all screws on the cylinder cap.
2. Have a qualied service technician install a new head valve piston set.
Tool does not work. 1. Make sure compressor is set between 90 to 125 PSI.
2. Check all air connections for leaks.
3. Make sure to fully depress the driver guide on the workpiece when
attempting to re a fastener.
4. Check for fastener jams. Clear the jam if necessary.
5. Have a qualied service technician check out the tool.
Sluggish operation. 1. Make sure compressor is set between 90 to 125 PSI.
2. Check all air connections for leaks.
3. Have a qualied service technician install a new head valve piston set.
Air leak near bottom of tool. 1. Tighten all screws.
2. Have a qualied service technician replace the bumper or head valve
piston set.
Poor return after ring the tool. Have a qualied service technician clean the interior of the tool and/or
replace the bumper or head valve piston set.
Weak driving force. 1. Make sure compressor is set between 90 to 125 PSI.
2. Check all air connections for leaks.
3. Have a qualied service technician clean the interior of the tool and/or
replace the bumper or head valve piston set.
Poor feed or tool jamming often. Have a qualied service technician clean the interior of the tool and/or
lubricate the magazine and install a new magazine spring.
Other problems. Have a qualied service technician inspect the tool.