© 2018 Centralite. All rights reserved.
Data Sheet: 3-Series Security Keypad (MSO) (3400-G) Page 3 of 3
Compatibility
The 3-Series Security Keypad features out-of-the-box compatibility with ZigBee HA 1.2 hubs and devices.
Troubleshooting
Step 1: Hardware Reset
Remove and replace batteries.
Step 2: Trigger Manual Rejoin
Remove the keypad from the wall and press the wall
tamper switch 5 times.
Step 3: Factory Default
Remove batteries from keypad. Press and hold the
wall tamper switch while reinstalling a battery. Once
the keypad illuminates, release the wall tamper switch.
Refer to Getting Started to rejoin the keypad.
Technical Specications
Electrical
Power: 3V - 2x CR-123a Batteries
Environmental
Operating Temperature: 0° to 40°C
Shipping / Storage
Temperature: -20° to 50°C
Humidity Range: 0 to 90% R.H.
(non-condensing)
Approvals:
Wireless RF
Protocol: ZigBee HA 1.2
TX Strength: +18 dBm
RF Channels: 16
Range: 300+ ft. (90+ m) L.O.S.
Temp Accuracy: ±1.8 °C (max), –10 to 85 °C
Precision: ± 0.1 °C
Standard WarrantySupport
Centralite offers a standard 12-month limited warranty
on the 3-Series Security Keypad.
Centralite offers both Tier-1 and Tier-2 support
structures to meet the needs of different customers.
For those customers that provide existing, in-house
support for systems, Centralite can serve as Tier-
2 support specialists. For Centralite retail-branded
products, Centralite provides direct Tier-1 support for
all products.
Contact Sales
For more information about sales or distribution,
please contact:
877-466-5483
Centralite Systems, Inc.
1701 Industrial Park Drive
Mobile, AL 36693
www.centralite.com
This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt
RSS Standards. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any interference received, including
interference that may cause undesired operation.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled
environment. This equipment is in direct contact with the body of the user under normal operating
conditions. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Changes or modications not expressly approved by Centralite Systems, Inc. could void the user’s
authority to operate the equipment.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit
pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner
avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie
Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres
utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée
équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication
satisfaisante.
Notice: Any content, factual information, or specications containing errors in this document are solely inadvertent and will be corrected
upon discovery. Specications for unreleased/planned products are subject to change.
