Centurionpro Hp1 User manual

OWNERS MANUAL

BUCKERS: HP1, HP3

2cprosolutions.com1 855 535 0558

GENERAL

• Do not move, disassemble, clean or inspect the Bucker while the power is still connected to the machine.

• The Buckers are very heavy - Never lift alone and always use proper lifting techniques.

• Ensure unit is secured to the stand, or is on a hard and leveled surface.

• Replacement parts are specic to The Buckers and must be purchased from an authorized dealer only.

• Substituting factory parts with non-approved third-party replacements may result in damage to the

machine or bodily harm.

• Keep all individuals a safe distance from the work area. Do not operate the machine around children.

• Do not remove safety labels. Replace any and all labels if they become damaged or obscured

CONNECTION

• As with home appliances, HP Buckers must be used in connection with a properly

grounded receptacle.

• Never plug in or power up your Bucker machine if the protective shrouds are removed.

• Do not use extension cords smaller than 12 gauge or longer than 7.6m (25ft) in length

to power the Bucker.

• Using unrated extension cords can cause motor overheating and premature failure.

The HP Buckers are high-powered machines that require special safety precautions to be practiced while in operation to reduce the risk of personal injury.

Improper use of the HP Bucker may cause serious or fatal injury. Please read the precautions and warning labels before using the HP Bucker.

IMPORTANT SAFETY INFORMATION

CENTURION PRO SOLUTIONS:

HP BUCKERS

OPERATION

• HP Buckers comes from the manufacturer set with the optimal roller settings. The initial set up will

show assembly instructions.

• Safety glasses and dust masks must be worn at all times when operating Buckers.

• Do not operate any Bucker machine while tired or under the inuence of medication, drugs

or alcohol.

• Do not put anything other than plant material into the Bucker. Doing so may cause damage to the

machine or result in bodily harm.

• Operate the Bucker in a well ventilated area in order to prevent overheating.

MAINTENANCE

• Never leave the HP Bucking system running unattended.

• Never conduct maintenance or cleaning while the machine is plugged in.

• Do not modify or adapt any part of the Bucker or its accessories. Doing so may cause irreversible

damage to the machine or result in bodily harm.

DO NOT LEND OUT OR RENT YOUR HP BUCKER WITHOUT THIS OPERATING MANUAL.

A FIRST TIME USER SHOULD OBTAIN PROPER INSTRUCTION PRIOR TO USE.

0PERATING THE HP BUCKER WITHOUT READING THE INSTRUCTIONS THAT ACCOMPANY A CAUTIONARY LABEL

(IE. "DANGER", "CAUTION", "WARNING", OR "NOTICE" SYMBOL), MAY RESULT IN SERIOUS OR FATAL INJURY.

FOR OPTIMAL PERFORMANCE AND LIFE, THE BUCKER MUST BE CLEANED AFTER DAILY USE.

For more information or to watch our video tutorials visit cprosolutions.com

OWNERS MANUAL

HIGH PERFORMANCE - HP BUCKERS

TABLE OF CONTENTS

IMPORTANT SAFETY INFORMATION

TABLE OF CONTENTS

COMPONENT OVERVIEW

CONTROL PANEL / EMERGENCY STOP OVERVIEW

CLEANING MAINTENANCE

ASSEMBLY TO STAND - HP1 & HP3

GENERAL OPERATIONS

GENERAL PERFORMANCE SPECIFICATIONS HP1

GENERAL PERFORMANCE SPECIFICATIONS HP3

TROUBLE SHOOTING

FREQUENTLY ASKED QUESTIONS

ADDITIONAL ASSISTANCE

WARRANTY

HP3 - ADDITIONAL REQUIREMENTS

EXTENSION CORD

12 AWG (min AWG SIZE)

7.6m/25ft MAX LENGTH

HP1 - ADDITIONAL REQUIREMENTS

EXTENSION CORD

14 AWG (min AWG SIZE)

7.6m/25ft MAX LENGTH

HP BUCKER CONNECTIONS

EUROPE, SOUTH AMERICA & ASIA

CONNECTOR PLUG

REGULAR WALL OUTLET

HP BUCKER CONNECTIONS

CANADA, USA, MEXICO & JAPAN

CONNECTOR PLUG

REGULAR WALL OUTLET

4cprosolutions.com1 855 535 0558

COMPONENT OVERVIEW

HP3

HP1

CP-7041

SEW CONTROLLER

MOVITRAC

CP-7036

SPUR GEAR

CP-7044

SEW EURO DRIVE

MOTOR

CP-7037

SPUR GEAR

NO HUB

CP-7031

GEAR COVER

CP-7039

MOUNT PLATE

CP-7034

FRONT CUT PLATE

CP-7047

CUTTERS

CP-7038

COVER MOTOR

CP-7045

MOUNTED

BEARING

CP-7027

BEARING

1"ID, 2"OD

CP-7030

IDLE SHAFT

CP-7029

DRIVE SHAFT

CP-7028

ROLLER

CP-7040

FRONT PLATE

CP-7042

EMERGENCY

STOP BUTTON

CP-7043

SET SCREW &

WINGNUT

CP-7035

BACK COVER TOP

CP-7032

SPRING CAP

CP-7033

COMPRESSION

SPRING

For more information or to watch our video tutorials visit cprosolutions.com

OWNERS MANUAL

HIGH PERFORMANCE - HP BUCKERS

HP3

HP1

FWDREV

PWR

OFF

CONTROL PANEL OVERVIEW

EMERGENCY STOP BUTTON OVERVIEW

START BUTTONSPEED DIAL

6-DIGIT DISPLAY

STOP / RESET BUTTON

FORWARD OR

REVERSE SWITCH

NAVIGATE BUTTON

POWER SWITCH:

ON / OFF

UP BUTTON

DOWN BUTTON

EMERGENCY STOP BUTTON

Located on top of HP Bucker

*Ensure machine is unplugged before cleaning.

6cprosolutions.com1 855 535 0558

CLEANING & MAINTENANCECLEANING & MAINTENANCE

STEP 1:

REMOVE

FRONT PLATE

STEP 4:

CLEANING

Thoroughly clean

inside bucker by

removing all loose

debris & blockage.

Re-assemble bucker

in reverse order.

STEP 2:

REMOVE FRONT

CUT PLATE

STEP 3:

CLEAN BOTH

ROLLERS WITH

CLOTH

STEP 5:

REASSEMBLE

BUCKER

FOR OPTIMAL PERFORMANCE AND LIFE, THE BUCKER

MUST BE CLEANED AFTER DAILY USE.

HP3

HP1

A) Remove using:

8 - 3/16" x 1" bolts

A) Remove using:

2 - 3/16" x 1" bolts

STEP 1:

REMOVE

LEGS

STEP 2:

MOUNT BUCKER

ONTO STAND

ASSEMBLEY TO STAND

Unscrew legs from

Bucker (HP1 only).

STEP 3:

PLUG IN AND

START BUCKING

Repeat 3x for the Triple Stand

HP3

HP1

A) Line up existing holes of the

bucker to the holes on the

stand plate. Attach using:

6 - 3/16" hex top

1/4"-20 x 1.25" bolts

For more information or to watch our video tutorials visit cprosolutions.com

OWNERS MANUAL

HIGH PERFORMANCE - HP BUCKERS

**Optional O -road tire can

be bolted onto stand

8cprosolutions.com1 855 535 0558

GENERAL OPERATIONS

Directions for cleaning:

1. Make sure Bucker is turned o

2. Using provided tools, remove Front Plate and Back top plate

3. Wipe down front plate liberally with isopropyl alcohol

4. Wipe down using a soft cloth, making sure the machine is dry completely

5. Clear out any debris from within the Bucker

6. Spray rollers liberally with isopropyl alcohol

7. Wipe down using a soft cloth, making sure the machine is dry completely

8. Reassemble according to "Cleaning and Maintenance" section

The HP Bucker is a precision machine. It is essential that it is operated and maintained

with this in mind. The machine has been adjusted and tested by the manufacturer prior to

shipping to ensure optimal performance. However, it is important to inspect the machine at

initial start-up and after each use to ensure that no damage or plant material build-up has

occurred and that the rollers spin freely.

In addition, it is highly recommended to clean the machine at the end of every use. This

ensures that resin does not build-up and aect performance. This is especially important if

the machine has been stored for an extended period of time.

Resins and other plant by-products will build up and harden, becoming dicult to remove.

Cold water is recommended to spray on rollers during harvest to reduce build-up.

MACHINE MAINTENANCE

PREPPING YOUR PLANT:

2 STEPS FOR OPTIMAL PROCESSING

Inspection of the either HP Bucker should be conducted prior to each

use following the disassembly section on page 6 and these steps:

1. Unplug the Bucker and visually inspect all of the components for wear, damage and plant

matter build-up.

2. Remove the front plate and back top plate. See "Cleaning and Maintenance" section

for instructions.

3. Inspect the rollers for damage or cracking.

4. Ensure the rollers spins freely

5. Visually inspect the blower and ensure the Bucker is free of loose debris.

INSPECTION

A thorough cleaning of the HP Bucker should be performed after each use. Any resin build-

up on the machine attracts more resin, compounding the problem. Build-up can cause

decreased performance, overheating and could trip your circuit breaker. Future cleaning

also becomes more dicult if build-up is given a chance to dry out and harden. Operating

the HP Bucker in a cold environment will also reduce resin build-up.

After removing front and back plates, rollers can be cleared using hot water, or wiped

with isopropyl alcohol. Repeat 2-3 times to soften the resin, then powerwash to remove

debris. Any stubborn areas, may require scrubbing with a plastic scraper (do not use a metal

scraper). Plant matter build-up is the most obvious sign that more attention is needed in a

particular area. Dry the machine with compressed air or a soft cloth.

CLEANING

• There are a series of holes located on the front of the top plate for bucking

• Stems are fed through the holes of the machine by hand

• Each plant must have 3 inches of base stem to clear the buckers

• Please note all strains run dierently and denser strains may need the top colas

taken o before being run through the machine.

NOTE

• Tool kit provided with Bucker

• Brush / Plastic scraper

• Spray bottle lled with isopropyl alcohol

• Soft cloths

MATERIALS NEEDED

1) ENVIRONMENT PREPARATION

• Ensure adequate space

• Review electrical requirements

• Have adequate bins for product transport

• Cooler temperatures in processing room is benecial

2) PLANT PREPARATION

• Cut main stalk

• Seperate each individual stem (no 'Y' junctions)

• Leave enough stem for clearance into machine

• Ensure clean angled cuts for precise feeding

• Keep prepped product stem side up for eciency

• Size the stem to t the ideal hole

• Feed end rst into machine

• Use variable speed control to adjust ow

OWNERS MANUAL

HIGH POWER - HP BUCKERS

HP1 BUCKER SPECIFICATIONS

HP3 BUCKER SPECIFICATIONS

HP1 BUCKER

Input Voltage NA: 120V, 60 Hz Single Phase

EU, AUS: 240V/50HZ, Single Phase

Current Draw < 2.5A Operating

Drive Motor 0.75HP, IP54

Motor RPM 1690 RPM

Variable Speed Yes

Weight (w/o stand) 100lbs / 45kg

Length 24in / 61cm

Width 18in / 46cm

Height 22in / 56cm

Circuit Breaker Required NA: 15A/120V

EU, AUS: 15A/220V

HP3 BUCKER

Input Voltage NA: 120V, 60 Hz Single Phase

EU, AUS: 240V/50HZ, Single Phase

Current Draw 7.5A Operating

Drive Motor 0.75HP, IP54 (x3)

Motor RPM 1690 RPM (x3)

Variable Speed Yes

Weight (w/ stand) 500lbs / 227kg

Length 85in / 216cm

Width 32in / 82cm

Height 51in / 130cm

Circuit Breaker Required NA: 20A/120V

EU, AUS: 20A/220V

HP1 BUCKER FEATURES

Feed Throughput +175 lbs/hr (Hydrated)

Feed Entry Sizes 5-hole (3/16”, 1/4”, 3/8", 1/2”, 3/4”)

Feed Types Wet/Dry

Roller Sets Neoprene Rubber

Motor Pulse Yes

Reverse Operation Yes

Duty Cycle Continuous

Pull Speed 10-30 in/s

Pull Strength > 400 lbs

GMP Compliant* Yes

UL Compliant* Yes

CE Compliant* Yes

RoHS Compliant* Yes

Primary Material 304 Stainless Steel / Aluminum

HP3 BUCKER FEATURES

Feed Throughput +500 lbs/hr (Hydrated)

Feed Entry Sizes 5-hole (3/16”, 1/4”, 3/8", 1/2”, 3/4”)

Feed Types Wet/Dry

Roller Sets Neoprene Rubber

Motor Pulse Yes

Reverse Operation Yes

Duty Cycle Continuous

Pull Speed 10-30 in/s (x3)

Pull Strength > 400 lbs (x3)

GMP Compliant* Yes

UL Compliant* Yes

CE Compliant* Yes

RoHS Compliant* Yes

Primary Material 304 Stainless Steel / Aluminum

10 cprosolutions.com1 855 535 0558

HOW EASY IS IT TO CLEAN?

Our machines can be taken apart and cleaned within 10-15 minutes. The Bucker must be cleaned

after daily use. Just spray the rollers liberally with isopropyl alcohol, then wipe with a soft cloth. We

recommend to clean every 4-6 hours of use, but it depends on your strain. We know the importance of

down time during a harvest so we wanted to make this process extremely quick and easy

DO YOUR MACHINES TRIM WET OR DRY?

All CenturionPro Buckers trims both wet and dry to t your processing needs.

ARE YOUR MACHINES BUILT TO AN INDUSTRIAL STANDARD?

We do not compromise quality for cost savings. All CenturionPro Solutions machines are composed

of the highest quality materials available in North America and each machine is put through a

comprehensive quality control inspection. We only use brand name components in the build out of

our Bucker machines which enables us to have the comfort in giving you a 2 year warranty. With proper

maintenance these machines will last you well over a decade.

FREQUENTLY ASKED QUESTIONS

WHAT IS THE OPTIMAL ROOM TEMPERATURE TO TRIM?

Use your CenturionPro Bucker in 50-60 °F (10- 15 °C) room to get the best performance.

Cooler temperatures prevent excessive sticking to machine components.

MY MACHINE IS NOT WORKING LIKE IT DID WHEN IT WAS NEW, WHY?

Make sure to fully clean the machine and rollers. If the machine is clean and the rollers are free of

debris, then your machine should trim exactly like it was new.

WE ARE OPEN MONDAY THROUGH FRIDAY FROM 9AM TO 5PM PST - PH: 1-855-535-0558

FILLING OUT THE “CONTACT US” FORM ON THE WEBSITE, IS ANOTHER SURE WAY TO GET IN TOUCH.

1) MOTOR IS VERY HOT

The motor is designed to operate at higher temperatures, avoid contact with the motor during regular operation. The motor is thermally fused and will shut down

automatically if overheating occurs

2) MACHINE IS JAMMED, OR MISFED WITH PLANT MATTER

This can happen when too large of a branch is put through the machine. Press and hold the reverse pulse button to rotate the rollers backwards while pulling on the branch.

3) THERE IS A GRINDING SOUND COMING FROM THE MACHINE

This can be caused by worn out bearings, misaligned gears or improperly installed components. If the pull-wheels were recently replaced / cleaned; then it is likely an

alignment issue, otherwise the bearings are damaged and need replacement.

4) THE PULL FORCE SEEMS WEAK

This could be caused by excessive debris build-up in the rollers. Disassemble, clean and inspect machine to determine the issue.

5) ROLLERS ARE SLIPPING

Slipping occurs if the motor reaches it's torque limit, or the roller friction has been reduced. Roller friction can be reduced by feeding excessively wet material or if any

lubricants accidentally get on the roller. Check to see if the rollers are dry and clean.

6) WHAT SPEED SHOULD I USE FOR WET MATERIAL?

We recommend a faster speed for wet product and a slower speed for dry.

7) DOES THE STEM HAVE TO BE A CERTAIN LENGTH TO FEED TO THE BUCKER?

Yes, there must be 3 inches of base stem to clear the cutters.

8) DO I NEED A SPECIAL OUTLET FOR THE BUCKER?

CenturionPro Buckers can be plugged into any standard 110V wall outlet (220V AUS/EU).

9) DO THE HP or HP3 BUCKERS WORK BEST WITH A PARTICULAR STRAIN?

HP Buckers can handle any strain but please note that all strains run dierently and denser strains may need the top colas taken o before being run.

TROUBLE SHOOTING

FOR ALL OTHER ISSUES, PLEASE EMAIL [email protected], WE WOULD BE HAPPY TO HELP YOU.

For more information or to watch our video tutorials visit cprosolutions.com

OWNERS MANUAL

HIGH PERFORMANCE - HP BUCKERS

YOU MUST REGISTER YOUR BUCKER WITHIN 30 DAYS OF YOUR PURCHASE

WARRANTY

YOU HAVE JUST MADE A SMART DECISION BY PURCHASING THE BEST BUCKER IN THE WORLD. FAILURE TO REGISTER YOUR BUCKER WITHIN 30

DAYS OF PURCHASE WILL VOID YOUR 2 YEAR WARRANTY. PROTECT YOUR INVESTMENT. THIS PROCESS WILL ONLY TAKE 3 MINUTES TO COMPLETE.

TO REGISTER GO TO:

cprosolutions.com/warranty

WARRANTY TERMS AND CONDITIONS

LIABILITIES

LEGALITIES

CenturionPro Solutions (the manufacturer) will repair or replace, without charge,

any parts proven defective in material or workmanship for a period of 2 years on the

Bucker Machine.

The warranty period will begin on the date the machine(s) is purchased by the initial

purchaser. Product or component warranty defects can be remedied at any authorized

service dealer, or directly at the manufacturer. Any service work performed, and deemed

valid due to a defective part, will be free of charge. CenturionPro Solutions reserves the right

to use any manufacturer-approved replacement part for the warranty repair

The machine or defective part then must be returned to the manufacturer for analysis or

replacement at the cost of the owner. Parts deemed to be covered under the warranty will

be provided for free excluding shipping costs.

Do not return the machine to the place of purchase for repair or warranty claims, unless

you have been authorized by CenturionPro Solutions to do so. The place of purchase can

only sell replacement parts and will not repair any warranty issues, unless it is noted as an

authorized repair dealer and has been authorized to work on your machine.

CenturionPro Bucker machines are intended for use on legal aromatic herbs and hops. Please check all municipal, provincial/state and federal laws and

regulations before using these machines. CenturionPro Solutions does not promote or condone the use of these products in any way that may be deemed

illegal. Allow only persons who understand this disclaimer to operate the machines.

The manufacturer assumes no risk and shall be subject to no liability for damages or loss resulting from the specic use or application made of the

product. In no event will the manufacturer be liable for any special, incidental or consequential damages (including loss of use, loss of prot and claims of