CG Emotron VS10 User manual

Emotron VS10/VS30 AC drive
Diagnostic modules
Mounting Instructions

1
General information 1
First read, then start
1General information
1.1 First read, then start
Read this documentation thoroughly before carrying out the installation andcommissioning.
▶Please observe the safety instructions!
Document description
Information and tools with regard to the Emotron products can be found on the Internet:
http://www.emotron.com/services-support/file-archive
You will find information on wiring and commissioning in the mounting and switch-on instructions
of the inverter.
This accessory may be operated under the same conditions as the assigned products.
Deviating or additional operating conditions are given in this document.
WARNING!

2
Product description
2
Keypad
2Product description
Keypad
Parameter setting and diagnostics
Thanks to the intuitive operating structure, the navigation keys allow a quick and easy access to the most
important parameters, either to configure functions or to query current values. Parameters and actual values
are indicated on the easy-to-read display.
Function of the keypad keys in operating mode
Key
Actuation
Condition
Action
Shortly
Local keypad control active.
Display "LOC"
Run motor.
Remote controlactive
Display
"REM"
Display "KSTOP"
Deactivate keypad triggered stop.
The motor remains at
standstill.
Display changes from "KSTOP" to"STOP"
Shortly
No Jog operation
Stop motor.
Display
"KSTOP"
Shortly
Operating mode
Change to parameterisation mode.
More than 3 s
None (anytime possible)
Save parameter settings in the user memory of the
memory module.
Shortly
During operation
Scroll through information in the above status line.
Shortly
Manual setpoint selection via keypad
active.
Display
"MAN"
Change frequency setpoint.
CTRL
Shortly
Operating mode
Activate full keypad control
Display
"ON?" Confirm with
Control and setpoint
selection can now only be carried
out via
keypad.
Actuating
again:
Display
"OFF?" Confirm with
Exit full keypad
control.
R F
Shortly
Local keypad control active.
Display "LOC"
Reversal of rotation direction.
Display "REV?" Confirm with

3
Product description
Keypad
Function of the keypad keys in the parameterisationmode
Key
Actuation
Condition
Action
Shortly
Local keypad control active.
Display "LOC"
Run motor.
Remote controlactive
Display "REM"
Display "KSTOP"
Deactivate keypad triggered stop.
The motor remains at standstill.
Display changes from "KSTOP" to"STOP"
Shortly
No Jog operation
Stop motor.
Display "KSTOP"
Shortly
Parameterisation mode
Navigate to one level below.
Group level, Parameter level [SUB parameter level] or
Editingmode
Editing mode
Exit editing mode and accept new setting.
More than 3 s
None (anytime possible)
Save parameter settings in the user memory of the
memory module.
Shortly
Parameterisation mode
Navigate to one levelabove.
[SUB parameter level] Parameter level Group level
or Operatingmode
Editing mode
Abort
Exit editing mode without accepting new setting.
Shortly
Group level/Parameter level
Navigate:Selectgroup/parameter.
Editing mode
Change parametersetting.
Without function
Without function

2
Product description
4
USB module
USB module
Interface to the PC
The USB 2.0‑connecting cable is used to connect the inverter with the "EASY Starter" Emotron
Commisioning & Maintenance Tool. The "EASY Starter" serves to configure the inverter via graphical
interfaces. They create diagnostics
with trend functions or monitor parameter values.
Parameterising without supplying the inverter with voltage: If you connect the inverter without hub directly
to the PC, the USB interface of the PC is sufficient for the voltage supply.
Inverters with network option EtherCAT, PROFINET or EtherNET/IP must be supplied with an
additional voltage (inverter AC power on) for setting parameters if a connection cable longer than 3 m
is used.
Please observe the following for USB modules labelled as "PRE-SERIES": Inverters withnetwork
option EtherCAT, PROFINET or EtherNET/IP must always be supplied with an additional voltage for
setting parameters.

5
Product description
WLAN module
WLAN module
The wireless interface
Wireless communication with the inverter.
• via a PC with the «EASY Starter« Emotron Commisioning & Maintenance Tool
▶ This product must not be collocated or operated in conjunction with any other antenna or
transmitter.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
▶ Le produit ne doit pas être utilisé en combinaison avec d’autres antennes ou transmetteurs.
LED status displays
LED 1
LED 2
LED 3
Meaning
Power (green)
TX/RX (yellow)
WLAN (green)
Supply voltage status
Communication status
WLAN status
OFF
OFF
OFF
No voltage
ON
ON
ON
Self-test (approx. 1 s)
ON
OFF
OFF
Ready for operation
No active WLAN connection
ON
Flashing
ON
Communication active
ON
OFF
Blinking
Client Mode
Waiting for connection
Blinking
OFF
OFF
Trouble
Additional conformities and approvals
CE R&TTE/RED
EN 301489-1 V1.9.2:2011
EN 301489-17 V2.2.1:2012
EN 300328 V1.8.1:2012-06
Connection data (defaultsetting)
IP address
192.168.178.1
SSID
<Product type>_<10-digit identifier>
Password
password
WARNING!

2
Product description
6
Mounting 3
Mounting steps
3Mounting
3.1 Mounting steps
1. Hook the diagnostic module into the upper mounting slots.
2. Turn it downwards until it engages into the lower mounting slot.
The diagnostic module is mounted.
The mounting steps are the same for all diagnostic modules and the blanking cover. This example
shows the installation of the Keypad.

© 07/2016 |13520839 | 4.0 / 01-6212-01R2
CG DRIVES & AUTOMATION
Mörsaregatan 12,
Box 222 25
SE- 250 24 Helsingborg,
Sweden
[phone]
Info: [e-mail]
Order: [e-mail]