CG MERIDIA User manual

WATER DISPENSER
CGMRBCM2

The installation and maintenance has to be carried out by qualified professionals or authorized
technicians.
The manufacturer shall not be held responsible for any damage or malfunction caused by wrong
installation or failing to comply with following instructions included in this pamphlet.
For more detailed installation and maintenance guidelines, please refer to below chapters.
TABLE OF CONTENTS
●
●
●
General Remark
1
TITLE PAGE
1. SAFETY INSTRUCTIONS...............................................................................................(2)
2. FUNCTION INTRODUCTION..........................................................................................(2)
3. PART NAME....................................................................................................................(3)
4. GETTING STARTED.......................................................................................................(4)
5. CAUTION........................................................................................................................(4)
6. TROUBLE SHOOTING....................................................................................................(6)
7. CLEANING......................................................................................................................(6)
8. MACHINE INSTALLATION..............................................................................................(7)

1. SAFETY INSTRUCTIONS
2. FUNCTION INTRODUCTION
2
2
1. This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
2. Children should be supervised to ensure that they do not play with the
appliance.
3. This appliance is intended to be used in household and similar
applications such as: staff kitchen areas in shops, offices and other
working environments; farm houses and by clients in hotels, motels and
other residential type environments; bed and breakfast type environments;
catering and similar non-retail applications.
4. If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a hazard.
5. The appliance must not be cleaned by a water jet.
6. The appliance is suitable for indoor use only.
7. WARNING: Keep ventilation openings, in the appliance enclosure or in
the built-in structure, clear of obstruction.
8. WARNING: Do not use mechanical devices or other means to accelerate
the defrosting process, other than those recommended by the manufacturer.
9.The appliance must not be immersed.
10. This product is not recommended to use in areas above 1,500m altitude.
11. It is recommended to use bottled pure water. If you use hard water, may
lead to hot pot furring or detonation tank or pipeline risk. If you need
cleaning tube, remove scale, need to find a professional institutions and
professional operation.
12. WARNING: When positioning the appliance, ensure the supply cord is
not trapped or damaged.
13. WARNING: Do not locate multiple portable socket-outlets or portable
power supplies at the rear of the appliance.
14. In order to make sure the machine can be used normally, please keep it
stand still for 24 hours before powering up.
1. This series model can satisfy the need of tea&coffee and making drinking.
It must be used indoor only.
2. With adoption of distinctive thermal isolation technology, this machine can
minimize thermal exchange between hot&cold water.
3. Warning Do not damage the refrigerant circuit.
4. Do not store explosive substances such as aerosol cans with a flammable
propellant in this appliance.

3. PART NAME
3
Power supply cord
Outlet of hot water
Condenser
Button of hot water
Button of normal water
Button of cold water
Door
Cooling pilot lamp
Heating pilot lamp
Power pilot lamp
Spout
Heating switch
Cooling switch
Bottle supporter
Top cover
Water collector
NOTE:
This machine is suitable for bottle of 3 or 5 gallons. Don’t use unhealthy hard
water.

4
4. GETTING STARTED
5. CAUTION
1. Tear the label from the bottle.
2. Vertically insert the bottle into the bottle supporter on top of the
machine. Do not plug the power cord or push the heating switch
until water runs out from the tap of hot water.
3. Insert the plug to socket, then turn on the power switch. Indicators
light up accordingly once the machine works.
4. Vertically pull out the bottle by two hands when the bottle is empty,
then replace it with another bottle of water.
5. This appliance should work under environment of temprature from
10°C-43 °C humidity ≤ 90%.
6. This appliance is not suitable for installation in an area where a water jet could be used.
1.
2.
3.
4.
Keep this machine in a dry place and avoid direct sunlight. Rear of the
machine should be at least 25cm away from the wall. Never put the
machine on paper or foam, which may cause unstable surface, Never
put anything flammable beside this machine.
To avoid damage to the machine, don’t plug the power cord or turn on
the heating switch until water runs out from the tap of hot water.
In case hot (or cold) water is not needed for a long time, turn the switch
accordingly to save power.
In case when not using this machine for a long time, turn off the
switches, then pull the plug out from socket and drain the remaining
water through draining outlet.

5
5.
6.
7.
8.
9.
10.
Never use organic liquid to clean the machine. Strictly prohibit splashing
water on the unit.
Never turn on(off) the machine by plugging the plug to (pulling the plug
out from) the socket. Never increase the length of the power supply cord
to avoid fire.
If the power cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a hazard.
The water cooler shall plug into a ground fault interrupter receptacle.
Never turn the machine upside down or tilt it more than 45°.
When the machine is below the freezing point and blocked by ice, the
cooling switch must be closde for 4 hours before turning it on again to
continue its operation .
This machine should not be turned on until 3 minutes later after turning
off the power switch .
11. TWhen first time to utilize the refrigerating function, let the refrigerating
function be operated for at least 2 hours before putting anything into the
cabinet. No wet or hot goods is allowed to be put into the cooling
cabinet. Leave suitable space between the goods to ensure the interior
airflow.

6
6. TROUBLE SHOOTING
7. CLEANING
To avoid accident, cut off the power supply before operation accordingto the following
instructions.
1. The machine had been disinfected before departing from factory. Clean the Clean the dispenser
prior to installing a full bottle of water for the fist time.
2. Cleaning and draining instruction:
1) Before cleaning, make sure the power switch in the O(off) position and unplug the water
dispenser.
2) Vertically insert the bottle into the supporter on tap of the machine.
3) Open the taps, let about 3 liter water flow into a container.
4) Remove the water bottle from the dispenser.
5) Place a large bucket beneath the drain outlet. Remove the drain cover and allow water to drain.
6) After draining, replace the drain cover and you can use the machine.
Attention: The dispenser heats water to a temperature of approximately 85 °C. It can cause severe
burns. Please operate it carefully.
3. Sanitizing
The machine should be disinfected with a disinfectant according to the instruction manual of the
disinfectant and then clean it with water(see cleaning and draining instruction) Generally this should
be done every three months.
Please check the followings before having the machine repaired.
PROBLEMS POSSIBLE CAUSES ELMINATION
Not hot or cold
water
1. Over consumption of hot or
cold water in short time.
2. No power supply
1. Just wait a moment, then hot or
cold water is available again.
2. Connect plug to socket, turn on
heating or cooling switch.
No water
running out
from taps
1. Empty bottle
2. Inlet of bottle supporter
blocked by bottle seal
1. Replace it with another one.
2. Clean out wasted paper & bottle
seal, install bottle again
Leakage from
bottle supporter Broken bottle Replace it with a new bottle
Noisy operation Not placid installation
Place the machine on placid &
solid surface

7
8. MACHINE INSTALLATION
4. To Remove Mineral Deposits:
Mix 4 liters water with 200g citric acid crystals, inject into the machine and make sure the water
can flow out of the hot water tap. Switch on the power and heat it about 10 minute. 30 minutes
later, drain off the liquid and clean it with water two or three times. Generally this should be done
every six months.
Never disassemble this machine by yourself to avoid danger from damagingmachine.
WARNING! To avoid a hazard due to instability of the appliance, it must be fixed in accordance
with the instructions.
Water dispenser
The hole for
tighten screw
1-2. Screw onto the lower middle hole.
3. Fix the machine on the table or the ground

The packaging material used is recyclable; we recommend that you separate plastic, paper
and cardboard and give them to recycling companies. To help preserve the environment,
the refrigerant used in this product is R134a (Hydrofluorocarbon -HFC), which does
not affect the ozone layer and has little impact on the greenhouse effect. According to
WEEE (Waste of Electrical and Electronic Equipment) guidelines, waste from electrical and
electronic devices should be collected separately. If you need to dispose of this appliance
in the future, do NOT throw it away with the rest of your domestic garbage. Instead, please
take the appliance to he nearest WEEE collection point, where available.