Chamberlain 950EV User manual

1-BUTTON REMOTE CONTROL MODEL 950EV
To prevent possible SERIOUS INJURY or DEATH from a moving gate
or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote controls.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate ordoor.
Your remote control is designed for use with garage door openers
manufactured starting January 1, 1993 that have a LEARN button.
The images throughout this manual are for reference only and your
product may look different.
BEFORE YOU START
Locate the LEARN button on the garage door opener, and then locate the
program button on the remote control.
IMPORTANT: The remote will activate your door or gate during
programming. Be sure the door is clear of ALL obstructions. Start with the
garage door closed. Make sure the garage door opener has a working light
because it is a programming indicator.
PROGRAM TO GARAGE DOOR OPENERS WITH A
YELLOW LEARN BUTTON
If your remote was previously programmed to another type of opener,
follow the programming instructions for PROGRAM TO ALL GARAGE
DOOR OPENERS below to reprogram to a yellow LEARN button.
1. Start with the garage door closed.
2. Press and immediately release the yellow LEARN button. The Learn
LED glows steady for 30 seconds. Within 30 seconds...
1. Press and hold the button on the remote control.
2. Release the button when the garage door opener lights blink or two
clicks are heard.
3. Test by pressing the button you just programmed. The opener
activates.
PROGRAM TO ALL GARAGE DOOR OPENERS
1. Press and hold the program button with the visor clip until the LED on
the front of the remote control turns on.
2. Press and release the remote control button the number of times that
corresponds with the garage door opener type. NOTE: Make sure the
LED stops flashing between each press of the button.
# of Presses Garage Door Opener Type
1 Yellow LEARN Button (Security+ 2.0®)
2 Purple LEARN Button (315MHz Security+®)
3 Red/Orange LEARN Button (390MHz Security+®)
4 Green LEARN Button (390MHz Billion Code)
3. Press the program button with the visor clip until the LED on the front
of the remote turns off.
4. Choose from Options A, B, C, or D to complete programming.
Option A: Program Using the Push Button Door Control
5. Press and hold the light button and the push button until the push
button LED begins to blink.
6. Press and hold the button on the remote until the garage door lights
blink or two clicks are heard. Release the button. Programming is
complete.
7. Test by pressing the button you just programmed. The opener
activates.
WARNING: This product can expose you to chemicals including
lead, which are known to the State of California to cause cancer or
birth defects or other reproductive harm. For more information go
to www.P65Warnings.ca.gov.
Green or Red/Orange
LEARN Button
Purple
LEARN Button
Yellow
LEARN Button
Learn LEDLearn LED Learn LED
Program Button
Push Button Light Button
LED

ONE YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. warrants to the first consumer purchaser of
this product that it is free from defect in materials and/or workmanship for
a period of 1 year from the date of purchase.
REPLACEMENT PARTS
Description Part Number
3V 2032 Lithium battery K010A0020
Visor Clip K029B0137
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)this device
must accept any interference received, including interference that may cause undesired operation.
The lithium battery should produce power
for up to 5 years. If the remote control’s
LED will not flash when the button is
pressed, replace the battery.
1. Pry open the case with the visor clip,
first in the middle (1), then at each
side (2 and 3).
2. Remove the old battery. Dispose of
old batteries properly.
3. Insert replacement batteries positive
side up. Replace the batteries with
only 3V CR2032 coin cell batteries.
4. Replace the cover.
© 2020, The Cahmberlain Group Inc.
114-5496-000 All Rights Reserved www.chamberlain.com
PROGRAM TO ALL GARAGE DOOR OPENERS
(CONTINUED)
Option B: Program Using the Smart Control Panel
5. On the Smart Control Panel, press the MENU button.
6. Use the arrow buttons to scroll to “PROGRAM”, and select to
the next screen.
7. Scroll down to “REMOTE,” and select .
8. Press and hold the button on the remote until the garage door lights
blink or two clicks are heard. Release the button. Programming is
complete.
9. Test by pressing the remote control button you just programmed. The
opener activates.
Option C: Program Using the Multi-Function Door Control or
Motion Sensing Door Control
5. On the door control, press the LEARN button twice.
6. Press and hold the button on the remote until the garage door lights
blink or two clicks are heard. Release the button. Programming is
complete.
7. Test by pressing the button you just programmed. The opener
activates.
Option D: Program Using the Garage Door Opener
5. Press and release the LEARN button on the garage door opener. The
Learn LED will light. Within 30 seconds...
6. Press and hold the remote control button until the garage door opener
lights flash or two clicks are heard. Release the button. Programming
is complete.
7. Test by pressing the button you just programmed. The garage door
will activate.
HOW TO USE THE REMOTE CONTROL
Press and hold the button until the door or other programmed device starts
to move. The remote control will operate from 1 to 3 car lengths away on
typical installations. Installations and conditions vary.
ERASE REMOTE CONTROL PROGRAMMING FROM THE
OPENER
The following steps will erase ALL remote controls and any keyless entries
from your opener.
1. Press and hold the LEARN button on the garage door opener until the
Learn LED turns off (approximately 6 seconds).
2. Test by pressing the button on the remote control to ensure it no
longer activates the opener.
3. Follow programming steps to reprogram the remote control.
REPLACE THE REMOTE CONTROL BATTERY
Multi-Function Door Control Motion Sensing Door Control
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V CR2032 corn batteries.
• DO NOT recharge, disassemble, heat above 212°F (100°C)
orincinerate.
2
3
1
3V CR2032
For more information and support, go to:
support.chamberlaingroup.com
5
TO REMOTE
67