Chameleon Lighting P59 User manual

10 Strecker Road Ellisville, MO 63011 888-896-2101 888-896-2101 Fax
www.ChameleonLTG.com [email protected] Email
INSTALLATION INSTRUCTIONS FOR CHANGING POWERCORDS IN
FIXTURE: P59 PASSIVE FROM 3-WIRE TO 5-WIRE FOR USE WITH WRAP
WARNING: Risk of fire and electric shock! This fixture must be installed
by a qualified electrician only! MAKE SURE ELECTRICAL CURRENT IS
DISCONNECTED BEFORE MAKING ELECTRICAL SPLICES
DISCONNECT POWER
1. REMOVE THE FIXTURE FROM THE CEILING.
2. LOOSEN STRAIN RELIEF IN THE CANOPY PLATE AND PULL 3-WIRE
POWERCORD OUT.
3. REMOVE (3) 4-40 SCREWS HOLDING THE SPLICE COMPARTMENT
COVER PLATE TO THE HEATSINK. UNDO ALL SPLICES TO 3-WIRE
POWERCORD IN SPLICE COMPARTMENT.
4. PERFORM ELECTRICAL CONNECTON TO 5-WIRE FIXTURE
POWERCORD: CONNECT RED WIRE FROM PASSIVE HEATSINK TO
BLACK WIRE FROM FIXTURE CORD, BLACK WIRE FROM PASSIVE
HEATSINK TO BWHITE WIRE FROM FIXTURE CORD, AND GROUND
WIRE FROM FIXTURE CORD TO GROUND WIRE FROM PASSIVE
HEATSINK (BY OTHERS) PLEASE NOTE: THE BLUE AND RED WIRES
FROM THE FIXTURE CORD INSIDE THE CAN ARE FOR THE WRAP-
AROUND LED PANEL AND SHOULD BE SPLICED TO THE LED WRAP
PLUG AND PULLED THROUGH THE OPEN HOLE IN THE SPLICE
COMPARTMENT COVER PLATE OPPOSITE THE GROUND WIRE
ATTACHMENT HOLE. THE WIRES AT THE OPPOSITE END OF THE
FIXTURE CORD, (THE END THAT IS ENCLOSED IN THE J-BOX (BY
OTHERS)) MUST BE CAPPED OFF W/ WIRE NUTS AS NECESSARY UNTIL
FUTURE USE.
5. SECURE SPLICE COMPARTMENT COVER PLATE TO HEATSINK
USING AFOREMENTIONED 4-40 SCREWS. ENSURE LED WRAP PLUG IS
OUTSIDE OF THE SPLICE COMPARTMENT.
6. SLIP 5-WIRE POWERCORD THROUGH CANOPY PLATE STRAIN
RELIEF.
7. PERFORM ELECTRICAL CONNECTION OF 5-WIRE POWERCORD TO
DRIVER: CONNECT BLACK TO RED, WHITE TO BLUE, AND GROUND TO
GROUND.
8. MOUNT CANOPY PLATE TO 4” OCTOGON J-BOX BY OTHERS. MAKE
SURE ALL 5 CONDUCTORS ARE AVAILABLE IN ELECTRICAL
ENCLOSURE FOR FUTURE EASY INSTALLATION OF LED WRAP-
AROUND PANEL.
RECONNECT POWER
CLEANING AND DIODE CARE: ANY DUST OR DEBRIS ON THE YELLOW PHOSPHER RESIN AREA OF THE
LED DIODE MAY ADVERSLY AFFECT DIODE PERFORMANCE AND SHORTEN THE LIFE OF THE DIODE.
ANY DUST AND DEBRIS MUST BE CLEANED PRIOR TO TURNING THE DIODE ON BY GENTLY RINSING IT
WITH ISOPROPYL ALCOHOL (COMMONLY CALLED RUBBING ALCOHOL) ON A Q-TIP. AVOID APPLYING
PRESSURE TO THE YELLOW PHOSPHOR RESIN AREA. CONTACT MAY CAUSE DAMAGE TO THE LED
ARRAY AND WILL VOID ANY MANUFACTURERS WARRANTY.

10 Strecker Road Ellisville, MO 63011 888-896-2101 888-896-2101 Fax
www.ChameleonLTG.com [e-mail] Email

10 Strecker Road Ellisville, MO 63011 888-896-2101 888-896-2101 Fax
www.ChameleonLTG.com [e-mail] Email
INSTALLATION INSTRUCTION FOR CLADDING KIT:
P59 LED WRAP ATTACHMENT COMPONENTS KIT AND
SIMILAR
WARNING: Risk of fire and electric shock! This fixture must be
installed by a qualified electrician only! MAKE SURE
ELECTRICAL CURRENT IS DISCONNECTED BEFORE
KIT INSTALLATION
DISCONNECT POWER
1. UNWRAP ALL FIXTURE COMPONENTS INCLUDING
SMALL PARTS BAG ENCLOSED.
PARTS LIST:
(3) M3 X 10 MM SCREWS
(1) SPREADER
(3) 8-32 X .5” ALL-THREAD
(3) 8-32 X .5” SCREWS
(3) 8-32 X 1” HEX COUPLERS
2. SLIP SPREADER AROUND POWERCORD AND REST ON
TOP OF HEATSINK. ENSURE THAT THE SPREADER IS
ORIENTED AS SHOWN. SECURE SPREADER TO HEATSINK
WITH (3) M3 X 10MM SCREWS.
3. ALIGN 8-32 X .5” ALL-THREADS WITH PEMSERTS IN THE
LONGER ARMS OF THE SPREADER AND INSERT WITH
APPROXIMATELY .25” STICKING OUT.
4. SECURE 8-32 X 1” HEX COUPLERS TO 8-32 X .5” ALL-
THREAD.
5. RAISE LED WRAP OVER P59 FIXTURE AND ALIGN HOLES
WITH 8-32 X 1” HEX COUPLERS. ENSURE THAT THE LED
WRAP PLUG FROM P59 FIXTURE CAN REACH ITS
CONNECTOR ON THE LED WRAP. SECURE TO HEX
COUPLERS WITH 8-32 X .5” SCREWS.
6. CONNECT LED WRAP PLUG FROM P59 FIXTURE TO LED
WRAP.
RECONNECT POWER