Lightolier Lighting Systems F7000-15 User manual

Job Information Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
"JSQPSU3PBE'BMM3JWFS."tt'BY
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt '
Lighting Systems F7000-15
1BHFPG '4FSJFT-JHIU5-PVWFS4PMJE4JEFT8BMM.PVOU
Features
1. Housing: Single piece of high purity extruded aluminum, a portion from
recycled material.
2. Housing End: Die-cast aluminum, welded in place.
3. End Cap: Die-cast aluminum. Encloses the end of the run.
4. Lamps: F28T5 or F54T5HO as specified. By others. Installed fromthe ceiling
side of the luminaire.
5. Ballast: Electronic. Meets ANSI starting, end-of-life protection and sound
rating specifications. Low THD.
Mounting
Each module includes two wall-mounting brackets. Bracket hole pattern accom-
modates junction box (single gang box rotated 90 degrees) or other appropriate
mounting method using customer supplied fasteners.
Labels
UL, cUL and I.B.E.W.
Ordering Instructions
Individual Fixtures:
1. Order one MODULE.
2. Order one END SET.
Continuous Rows:
1. Order the appropriate number of MODULES for the complete run.
2. Order one END SET.
Finish
Powder-coated, baked enamel, white or aluminum, as specified.
Ordering Information
1.63”
(4.14cm)
3.95” (10.03cm)
3.25”
(8.26cm)
FW7
Family Series
3
Type Lamps Color Wattage Voltage Length
4 1
3= Block 4= Louver 1= 1 LampAL = Aluminum
WH = White
1= 28W
2= 54W
3= 28W Dimming
4= 28W EM
5= 54W Dimming
6= 54W EM
1= 120v
2= 277v
4= 4’ (121.92cm)
8= 8’ (243.84cm)
5413.620”
(9.19cm)
1.304”
(3.31cm)
.750“
(1.91cm)
6. Louver Shielding
Complete Ordering Instructions below.
6. Shielding: Integral, regressed flat louver blades punched and formed from
fixture housing, finished to match, no light leaks. Blades are .56” (1.42cm) high
on .75” (1.91cm) centers.
Electrical
Connections: Pre-wired with 18 gauge wires and polarized cannon plug con-
nectors for simultaneous mechanical/electrical connection.
Emergency Battery Pack: 90 minute operation, 700 lumens for 54W and 520
lumens for 28W.
Dimming: Advance Mark X standard (no additional wires required); use compat-
ible dimmer. Dimming ballasts using additional control wires (eg Lutron Hi-Lume
or ECO-10, Osram) can be used; consult factory and use X4 or X5 power feeds
with additional leads, as appropriate. Ballast not to exceed 1.25” (3.18cm) wide by
1.20” (3.05cm) high.
iGEN: F7000 accepts iGEN (DALI) with supplemental 2-wire control technology.
Use with X5 power feed.
Power Tray: Code-gauge, die-formed steel, pre-paint white enamel finish;
secured by quarter-turn fasteners for easy access to wiring. Holds ballasts, sock-
ets, and wiring. Accepts ballasts up to 1.25” (3.18cm) wide by 1.20” (3.05cm) high.
Finish: Powder-coated, baked enamel, white or aluminum, as specified.
Factory installed ballast disconnect allows the ballast to be disconnected fromand
reconnected to incoming power under load without turning the entire circuit off.

Job Information Type:
"JSQPSU3PBE'BMM3JWFS."tt'BY
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt '
Lighting Systems F7000-15
1BHFPG '4FSJFT-JHIU5-PVWFS4PMJE4JEFT8BMM.PVOU
CANDLEPOWER
ZONE 0 22 45 67 90
DEG. CANDELAS
0 631 631 631 631 631
5 640 636 631 621 618
15 706 672 618 562 540
25 780 710 590 485 438
35 674 638 545 386 321
45 401 390 382 268 202
55 212 203 193 179 120
65 105 97 95 99 76
75 49 50 49 52 40
85 13 13 11 12 9
90 32110
95 39 44 52 73 37
105 269 285 295 293 153
115 544 553 543 419 279
125 771 742 642 529 404
135 801 780 711 603 506
145 812 799 748 646 589
155 797 786 741 680 651
165 742 736 722 699 689
175 704 705 707 705 704
180 702 702 702 702 702
Performance
CANDLEPOWER CURVE
810
608
405
203
0
10
20
30
40
50
60
70
80
0909
100
110
120
130
140
150
160
170
180
REPORT NO.: ITL54685.IES
LAMPS: 1-F54T5
LUMENS: 5000 each
EFFICIENCY: 77.9%
CAT. NO.: F7341WH214
DISTRIBUTION
Zone Lumens % Lamp %Luminaire
0 - 90 1246 24.7 32.0
90 - 180 2661 53.2 68.0
0 - 180 3907 77.9 100.0
80% 70% 50%
50 30 10 50 30 10 50 30 10
0 818181 7272 72 575757
1 706766 6462 59 504948
2 625854 5652 49 454340
3 554946 4945 42 403734
4 484339 4439 35 363229
5 443733 4034 30 322926
6 393329 3530 27 292522
7 352926 3227 24 272320
8 322722 2924 21 242017
9 292420 2722 18 221815
10 27 21 18 25 20 16 20 16 14
20% FLOOR CAVITY REFLECTANCE
COEFFICIENTS OF UTILIZATION
% EFFECTIVE CEILING CAVITY REFLECTANCE
WALL REFLECTANCE
ROOM CAVITY RATIO
Mounting Accessories
W
all Mount End Set
FW7EWH = White
FW7EAL = Aluminum
Fixture Lengths & Mounting Reflected (Plan View)
20'-3" (617.22cm)
16'-3" (495.30cm)
12'-3" (373.38cm)
8'-3" (251.46cm)4'-3" (129.54cm)
2'-8"
(81.28cm)6'-8" (203.20cm)
6'-8" (203.20cm)2'-8"
(81.28cm)
1'-4"
(40.64cm)
6'-8" (203.20cm)1'-4"
(40.64cm)6'-8" (203.20cm)
6'-8" (203.20cm)1'-4"
(40.64cm)6'-8" (203.20cm)2'-8"
(81.28cm)
1'-4"
(40.64cm)
16.00" (40.64cm)
3/4"
(1.91cm)
1-1/2"
(3.81cm)
3/8" (0.95cm)
END OF ROW DETAIL
GAP BETWEEN FIXTURES
JOINING DETAIL
Recommended mounting is a single gang outlet box rotated 90 degrees at the
feed point. Remaining mounting points could be outlet boxes as well, or a couple
of holes per mounting point spaced 3-1/4” (8.26cm) at 1-3/4” (4.45cm) above the
bottomof fixture.