Char-Broil Grill2Go Ice User manual

Assembly
Guide
Model Numbers:
08401504
PROPANE
(English)
Allow approximately 45 minutes for assembly.
42804526 • 11/25/2009
Propane cylinder
sold separately.
10401582
10401589
10401590
10401591
10401592
10401593
10401594

2 ASSEMBLY GUIDE
First -
Take a moment to record the serial number here: _______________________________
When grilling, preheat your grill for 10 to 15 minutes with the lid down.
After grilling—the grill can be turned on High for cleaning and burning off
the grate. - Use a wire brush to brush off the grate.
A light coat of oil on the grate will help prevent foods like fish and vegetables from
sticking to the grate.
A, B, C, Assembly:
CAUTION: For your safety, before operating, Read Product Guide & Outdoor Cooking Guide
provided with this grill.
*SAFETY First…..Grill components may have sharp edges. Be careful when handling grill parts
during assembly. We suggest that you wear a sturdy pair of leather gloves while handling the grill parts.
TIPS & Tricks…...
BEFORE You Grill….
1. Read Product Guide & Outdoor Cooking Guide
2. Position Grill safely away from walls & structures
3. Pre– Heat Grill—15 minutes on High to season grill.
TOOLS REQUIRED FOR ASSEMBLY
NOTE….
Installer: Leave instructions with the grill.
Consumer: Retain instructions for reference.
Grill must be installed in accordance with local
codes…..
Designed for outdoor use only…
Read all instructions before operating…
Phillips Head
Screwdriver
(Not Supplied)
Small Adjustable
Wrench
BEFORE You begin assembly of your grill….
1. Carefully remove all components from the carton.
3. Please note that hardware used for assembly may not be shown actual size..
2.
Familiarize yourself with the components and hardware used for assembly.
4. After removing components from the carton, split the carton open and use it as
a scratch-free work pad to assemble your grill.
Go to charbroil.com to register your grill.-

Key Qty Description
A 1 Grill Lid
B 1 Cooking Grate
C 1 Trough
D 1 Burner
E 1
F 1 Firebox Bottom
G 1 Heat Shield
H 2 Side Lift Mechanism
I 1 Rear Lift Mechanism
J 1 Left Side Shelf
K 1 Right Side Shelf
Inner Reflector
L 1 Regulator Control Valve
M 2 Wheel
Key Qty Description
N 1 Hinge Set
O 1
P 1 Handle
Q 1 Logo Plate
R 1 Electrode with Wire
S 2 Side Shelf Bushings
T 2 Cooler Bag
U 2 Axle Rod
X. 1 RH Cart Fascia
Venturi LatchAssembly
V 1 Cart Base
W 1 LH Cart Fascia
Y 1 Match Holder
Z 2 Cooler Tray Kit
NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from
those on your particular model. However, the method of assembly remains the same.
Key Qty Description
AA 1 Handle Heat Sheild
BB 1 Lid Clasp
CC 2 Cart Foot
DD 10 Tube Plug
EE 1 Venturi Guard
FF 1 Piezo Ignitor Button
GG 2 Cooler Liner
... 1 Hardware Pack
... 1 Assembly Manual, English
... 1 Assembly Manual, Spanish
1 Assembly Manual, French
1 Product Guide, English
... 1 Product Guide, Spanish
... 1 Product Guide, French
...
...
K
A
L
H
D
S
Q
F
I
J
P
N
3ASSEMBLY GUIDE Grill Parts Diagram
M
B
C
E
G
Y
V
W
X
ZR
U
GG
GG
AA
H
BB
CC
DD
EE O
FF
TT

4 ASSEMBLY GUIDE
Part Qty
A1– Cart RH Side Fascia 1
A2– Cart Base 1
A3– Cart Leveling Foot
2
A4–
Fasteners
#10x3/4"
(qty 2)
GRILL CART Assembly
Wheels 2(qty 14)
screw
Axle Rod
(qty 2)
Wheel Retaining
Clip
Step 2: Carefully place the cart assembly on its
back. Install the Cart Leveling Feet (A4) by
threading them into the bushings as shown.
These leveling feet can be used to adjust your
grill when using it on uneven surfaces. After
installation of the leveling feet, place the cart
in the upright position.
Step 3: Assemble the Wheels (A5) to the Cart Base
(A3) by first sliding an axle rod through the wheel,
then sliding the axle rod through the axle rod holes
in the cart base. Secure with a wheel retaining clip.
Repeat for the other side.
Wheel Retaining Clip - install after
placing wheel and axle rod through
axle hole.
Axle Rod
Axle Hole
Completed Cart!
A5
A3
– Cart LH Side Fascia 1
A5
A1
A2
A3
Step 1: Assemble the LH and RH Side Fascia (A1 & A2)
to the Cart Base (A3) by aligning screw holes in the
fascias with corresponding holes in the cart base.
Secure with 7 each, #10x3/4 screws (7 per side) using a
phillips screwdriver. Repeat for other side. NOTE: The
lift handles are shown in the up position. You can
complete steps 1 and 2 with the handles lowered if
desired.
A4
A3

5ASSEMBLY GUIDE
Part Qty
Fasteners
#10-24 x 1 1/4"
GRILL Assembly
(qty 4)
screw
B1–Heat Shield 1
B2–Fire Box Assembly 1
Note: Before beginning this step of the
assembly, raise the two side lifts to their
highest position by pressing the button
at the top of the handle and pulling
upward on the handle. B1
Firebox Mounting Brackets
Step 1 - Install the Heat Shield(B1) to
the firebox mounting brackets by
engaging the tabs into the slots located
in the mounting brackets as shown on
the right.
Step 2 - Install the Fire Box Assembly(B2) to the cart by first placing the firebox assembly onto the
firebox mounting brackets. Be sure that the lid clasp is toward the front of the cart. Align the firebox
screw holes with the corresponding holes in the mounting brackets. Insert 4 #10-24 x 1 1/4" machine screws
and 4 fiber washers through the firebox and mounting brackets. Secure with 4 #10-24 nuts and 4 #10
lock washers from below the mounting brackets as shown below.
Right hand side
Firebox screw
holes
Lid Clasp
B2
Fiber washers
Left hand side
Firebox screw
holes
#10-24
(qty 4)
nut
#10-24 nuts
#10 Lock
(qty 4)
washer
#10 lock washers
(qty 4)
Fiber Washer
#10-24 x 1 1/4"
machine screws

ASSEMBLY
6 ASSEMBLY GUIDE
Part Qty .
B3– Hinge, RH 1
B4– Hinge, LH 1
B7– Handle 1
Fasteners
Step 1 - Attach the Hinges (LH and RH) (B3 & B4) to the
Firebox Bottom by aligning the screw holes on the bottom of
the grill with the corresponding holes in the hinges. Secure
with 2 each #10-24x1/2" screws, 2 fiber washers and 2 #10-24
nuts as shown.
.
(qty 8)
Fiber Washer (qty 2)
Spacer for Lid
GRILL Assembly
LH side shown,
RH side similar.
Step 2 - Attach the Grill Lid (B5) to the Hinges by
aligning the screw holes on the grill lid with the
corresponding holes in the hinges. Secure with 2 each #10-
24x1/2" screws, 1 spacer and 2 #10-24 nuts as shown.
B5
B7
B6
B5
B2
B2
(qty 8)
10-24 Nut
B5– Grill Lid 1
(qty 12)
screw
10-24 x 1/2"
Step 3 - Attach the Heatshield (B6) and Handle (B7) to
the Grill Lid (B5) by aligning the screw holes in the handle
and heatshield with the corresponding holes in the Grill Lid.
Secure with 410-24 x 1/2" Screws and 4 fiber washers. Do not
over tighten the screws.
B6– Heat Shield 1
B4
B3
B4

7 ASSEMBLY GUIDE GRILL FINAL Assembly
Part Qty.
C1 – Side Shelf, RH 1
C2 – Side Shelf, LH 1
C3 – Trough 1
C4 – Cooking Grate 1
C6 – Cooler Bags/Coolers 2
Step 1 - Install the Regulator Control Valve (C5) by first sliding the regulator lock toward the rear of the grill, inserting
the Regulator Control Valve fully into the exposed burner tube, and then releasing the regulator lock. Next, press the end of
the Ignitor Wire (C7) onto the pushbutton ignitor as shown.
Step 2 - Place the Side Shelves RH and LH (C1 & C2) into position by aligning the mounting rods with the bushing located
in the firebox bottom. Press the shelves into place firmly. Place the Trough (C3) into the Firebox Bottom, then place the
Cooking Gate (C4) into the Trough. The Cooler Bags (C6) rest on the bottom shelf of the grill cart, as shown.
C5 – Regulator Control Valve 1
C5
C2
C1
C6
C6
C3
C4
C7 – Ignitor Wire
Part Qty.
1
C7
Regulator Lock
1. Slide to rear
Regulator
2. Insert Regulator fully
into burner tube.
3. Release lock.

© 2009 Char-Broil, LLC Printed in China• Columbus, GA31902 •