Chauvet Professional Epix Drive 900 User manual

User Manual
Firmware V1.1

Edition Notes
ÉPIX Drive 900 User Manual Rev. 1
Edition
Notes
The ÉPIX Drive 900 User Manual Rev. 1 covers the description, safety precautions, installation,
programming, operation, and maintenance of the ÉPIX Drive 900. Chauvet
released this edition
of the ÉPIX Drive 900 User Manual in January 2016.
Trademarks
CHAUVET, the Chauvet logo and ÉPIX Drive 900 are registered trademarks or trademarks of
Chauvet & Sons Inc. (d/b/a Chauvet and Chauvet Lighting) in the United States and other
countries. Other company and product names and logos referred to herein may be trademarks
of their respective companies.
Copyright Notice
The works of authorship contained in this manual, including, but not limited to, all design, text
and images are owned by Chauvet.
© Copyright 2016 Chauvet & Sons, Inc. All rights reserved.
Electronically published by Chauvet in the United States of America.
Manual Use
Chauvet authorizes its customers to download and print this manual for professional information
purposes only. Chauvet expressly prohibits the usage, copy, storage, distribution, modification,
or printing
of this manual or its content for any other purpose without written consent from
Chauvet.
Document
Printing
For better results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If
using A4 paper (210 x 297 mm), configure your printer to scale the content accordingly.
Intended
Audience
Any person in charge of installing, operating, and/or maintaining this product should completely
read through the guide that shipped with the product, as well as this manual, before installing
,
operating, or maintaining this product.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects.
However, Chauvet assumes no responsibility and specifically disclaims any and all liability to
any party for a
ny loss, damage or disruption caused by any errors or omissions in this
document, whether such errors or omissions result from negligence, accident or any other
cause. Chauvet reserves the right to revise the content of this document without any obligation
to notify any person or company of such revision, however, Chauvet has no obligation to make,
and does not commit to make, any such revisions.
Document
Revision
The ÉPIX Drive 900 User Manual Rev. 1 is the first edition of this manual. Go to
www.chauvetprofessional.com for the latest version.

Table of Contents
ÉPIX Drive 900 User Manual Rev. 1 -i-
Table of Contents
1. Before You Begin......................................................................................................................................1
What Is Included...........................................................................................................................................................1
Claims..........................................................................................................................................................................................1
Manual Conventions ....................................................................................................................................................................1
Symbols.......................................................................................................................................................................................1
Product At A Glance .....................................................................................................................................................2
Safety Notes .................................................................................................................................................................2
Personal Safety............................................................................................................................................................................2
Mounting And Rigging..................................................................................................................................................................2
Power And Wiring ........................................................................................................................................................................2
Operation.....................................................................................................................................................................................2
Expected LED Lifespan................................................................................................................................................2
2. Introduction...............................................................................................................................................3
Description....................................................................................................................................................................3
Features........................................................................................................................................................................3
Overview.......................................................................................................................................................................3
Dimensions...................................................................................................................................................................4
3. Setup..........................................................................................................................................................5
AC Power......................................................................................................................................................................5
AC Plug........................................................................................................................................................................................5
Power Linking ...............................................................................................................................................................5
Fuse Replacement.......................................................................................................................................................................5
Mounting.......................................................................................................................................................................6
Orientation ...................................................................................................................................................................................6
Rigging.........................................................................................................................................................................................6
Procedure ....................................................................................................................................................................................6
Signal Connections.......................................................................................................................................................7
Art-Net™ Connection...................................................................................................................................................................7
sACN Connection.........................................................................................................................................................................7
Kling-Net Connection...................................................................................................................................................................7
Connecting ÉPIX Products ...........................................................................................................................................8
4. Operation...................................................................................................................................................9
Control Panel Description.............................................................................................................................................9
Menu Map.....................................................................................................................................................................9
Ethernet Configuration................................................................................................................................................10
Protocol......................................................................................................................................................................................10
Start Universe ............................................................................................................................................................................10
IP Addresses..............................................................................................................................................................................10
Auto Addressing .........................................................................................................................................................10
View Linked Fixtures..................................................................................................................................................................10
Home Screen..............................................................................................................................................................11
Display Orientation .....................................................................................................................................................11
Device ID ....................................................................................................................................................................11
LED Output Test.........................................................................................................................................................11
Factory Reset .............................................................................................................................................................11
6. Technical Information.............................................................................................................................12
Product Maintenance..................................................................................................................................................12
7. Technical Specifications.........................................................................................................................13
Ordering......................................................................................................................................................................14
Returns ........................................................................................................................................................15
Contact Us...................................................................................................................................................16

Before You Begin
ÉPIX Drive 900 User Manual Rev. 1 -1-
1. BEFORE YOU BEGIN
What Is
Included
•ÉPIX Drive 900
•Neutrik® powerCON® power cord
•Rack ears (2) w/ screws
•Rubber feet (4)
•Warranty Card
•Quick Reference Guide
Claims
Carefully unpack the product immediately and check the box to make sure all the parts are in
the package and are in good condition.
If the box or the contents (the product
and included accessories) appear damaged from
shipping or show signs of mishandling, notify the carrier immediately, not Chauvet
. Failure to
report damage to the carrier immediately may invalidate your claim. In addition, keep the box
and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with Chauvet within 7 days of delivery.
Manual
Conventions
Convention
Meaning
1–512
A range of values in the text
50/60
A set of mutually exclusive values in the text
<SET>
A button on the product’s control panel
Settings
A product function or a menu option
MENU>Settings
A sequence of menu options
1–10
A range of menu values from which to choose in a menu
Yes/No
A set of two mutually exclusive menu options in a menu
ON
A unique value to be entered or selected in a menu
Symbols
Symbols
Meaning
Critical installation, configuration, or operation information. Failure to
comply with this information may cause the product not to work,
damage third-party equipment, or cause harm to the operator.
Important installation or configuration information. Failure to comply
with this information may keep the product from working.
Useful information.
The term “DMX” used throughout this manual refers to the USITT DMX512-A digital data
transmission protocol.

Before You Begin
-2- ÉPIX Drive 900 User Manual Rev. 1
Product At A
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-Ranging Power Supply
P
Master/Slave
x
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Safety Notes
Read all the following Safety Notes before working with this product. These notes include
important information about the installation, usage, and maintenance of this product.
This product contains no user-serviceable parts. Any reference to servicing in this User
Manual will only apply to properly trained Chauvet certified technicians. Do not open the
housing or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this product.
Personal Safety
•Avoid direct eye exposure to the light source while the product is on.
•Always disconnect this product from its power source before servicing.
•Always connect this product to a grounded circuit to avoid the risk of electrocution.
•
Do not touch this product’s housing during operation because it may be very hot.
Mounting And
Rigging
•This product is for indoor use only! To prevent risk of fire or shock, do not expose this
product to rain or moisture. (IP20)
•CAUTION: When transferring product from extreme temperature environments, (e.g. cold
truck to warm humid ballroom) condensation may form on the internal electronics of the
product. To avoid causing a failure, allow product to fully acclimate to the surrounding
environment before connecting it to power.
•Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from
adjacent surfaces.
•Make sure there are no flammable materials close to this product while it is operating.
•When hanging this product, always secure to a fastening device using a safety cable.
Power And
Wiring
•Always make sure you are connecting this product to the proper voltage in accordance
with the specifications in this manual or on the product’s specification label.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
•Never connect this product to a dimmer pack or rheostat.
•Never disconnect this product by pulling or tugging on the power cable.
Operation
•Do not operate this product if you see damage on the housing, lenses, or cables. Have the
damaged parts replaced by an authorized technician at once.
•Do not cover the ventilation slots when operating to avoid internal overheating.
•The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at a
higher temperature.
•In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your Chauvet product may require service, contact Chauvet
Technical Support.
Expected LED
Lifespan
LEDs gradually decline in brightness over time, mostly because of heat. Packaged in clusters,
LEDs exhibit higher operating temperatures than in ideal, single-LED condi
tions. For this
reason, using clustered LEDs at their fullest intensity significantly reduces the LEDs’ lifespan.
Under normal conditions, this lifespan can be 40,000 to 50,000 hours. If extending this lifespan
is vital, lower the operating temperature by improving the ventilation around the product and
reducing the ambient temperature to an optimal operating range. In addition, limiting the overall
projection intensity may also help to extend the LEDs’ lifespan.

Introduction
ÉPIX Drive 900 User Manual Rev. 1 -3-
2. INTRODUCTION
Description
ÉPIX Drive 900 hosts the processing and power supply for the ÉPIX Tour product line in one
convenient device. It controls up to 18 ÉPIX Strip Tour or 6 ÉPIX Bar Tour products
easily using
Art-Net™, sACN, or ArKaos Kling-Net. Configuration and setup is fast and easy with its built-
in
OLED display. Additionally, configuration can be managed with a network-
based remote web
server.
Features
•Ethernet, processing, and power hub for ÉPIX Tour product line.
•Operating modes:
oArt-Net™
osACN
oArKaos Kling-Net
•Auto-address function
•Single 4-pin XLR output
•2700 Art-Net™ channels
•Steel housing
•Neutrik® powerCON® power input/output connections
Overview
Front View
Top View
Rear View
Signal In/Out
(Through)
Fuse
Holder
Neutrik®
powerCON® In
Neutrik®
powerCON® Out
M12
Mounting
Points
ÉPIX Product
Output
(4-pin XLR)
OLED
Display
Menu
Buttons
Rubber
Feet
Removable Rack Ears
Indicator
LEDs
Safety Cable
Pass-
Through
Bottom View

Introduction
-4- ÉPIX Drive 900 User Manual Rev. 1
Dimensions
7.6 in
193 mm
19.02 in
483 mm
18.31 in
465 mm
1.18 in
30 mm
1.7 in
44 mm
1.97 in
50 mm
1.7 in
44 mm
11.14 in
283 mm

Setup
ÉPIX Drive 900 User Manual Rev. 1 -5-
3. SETUP
AC Power
Each ÉPIX Drive 900 has an auto-ranging power supply that works with an input voltage range
of 100 to 240 VAC, 50/60 Hz. To determine the power requirements for each ÉPIX Drive 900
,
refer to the label affixed to the product. You can also refer to the Technical Specifications
chart
in this manual.
The listed curr
ent rating indicates the maximum current draw during normal operation. For more
information, you may download Sizing Circuit Breakers from the Chauvet website
:
www.chauvetprofessional.com.
•Always connect this product to a protected circuit with an appropriate electrical
ground to avoid the risk of electrocution or fire.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Never connect this product to a rheostat (variable resistor) or dimmer circuit, even if the rheostat
or dimmer channel serves only as a 0 to 100% switch.
AC Plug
The ÉPIX Drive 900 comes with a power input cord terminated with a Neutrik® powerCON® A
connector on one end and an Edison plug on the other end (U.S. market). If the power input
cord that came with your product has no plug, or if you need to change the Edison plug, use the
table below to wire the new plug.
Connection
Wire (U.S.)
Wire (Europe)
Screw Color
AC Live
Black
Brown
Yellow or Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green
Power Linking
The ÉPIX Drive 900 supports power linking. You can power link up to 6 products at
120 V; up to 11 at 208 V; or up to 12 at 230 V.
This product comes with a power input cord. Power linking cables are available from Chauvet
for purchase.
Fuse
Replacement
Disconnect this product from the power outlet.1.
Using a flat-head screwdriver, unscrew the fuse holder cap from the housing.2. Remove the blown fuse and replace with another fuse of the same type and rating3. (T 5 A, 250 V).
Screw the fuse holder cap back in place and reconnect power.4.
Make sure to disconnect the product’s power cord before replacing a blown fuse. Always
replace the blown fuse with another of the same type and rating.

Setup
-6- ÉPIX Drive 900 User Manual Rev. 1
Mounting
Before mounting this product, read and follow the Safety Notes. For our CHAUVET
Professional line of mounting clamps, go to http://trusst.com/products/.
Orientation
Always mount this product in a safe position and make sure there is adequate room for
ventilation, configuration, and maintenance.
Rigging
Chauvet recommends using the following general guidelines when mounting this product.
•When selecting an installation location, consider easy access to this product for operation,
programming adjustments, and routine maintenance.
•The product is not intended for permanent installation.
•Make sure to mount this product away from any flammable material as indicated in the
Safety Notes.
•Never mount in places where rain, high humidity, extreme temperature changes, or
restricted ventilation may affect the product.
•Before deciding on a location, always make sure there is easy access to the product for
maintenance and programming.
•If hanging this product, make sure that the mounting location can support the product’s
weight. See the Technical Specifications for the weight-bearing requirements of this
product.
•When hanging this product, always secure to a fastening device using a safety cable. For
our CHAUVET Professional line of safety cables, go to http://trusst.com/products/.
•When mounting the product on the floor, make sure that the product and cables are away
from people and vehicles.
Procedure
The ÉPIX Drive 900 fits nicely in a standard 19” rack using the included removable rack ears.
You may also choose to attach a M12 mounting clamp for hanging or simply place it on its feet
on a flat level surface. You must supply your own mounting hardware. Make sure all hard
ware
and mounting surfaces are capable of supporting the weight of this product. For our CHAUVET
Professional line of mounting clamps, go to http://trusst.com/products/.
Mounting Diagram
Rack Mounting
Safety Cable
Overhead Mounting
Surface Mounting
Removable Rack Ear (x2)
Screw (x4)
Rubber Feet (x4)
Mounting Clamp
(Only one needed)

Setup
ÉPIX Drive 900 User Manual Rev. 1 -7-
Signal Connections
You can link the ÉPIX Drive 900 to controller software using an Ethernet connection. If using
other Art-Net™, sACN or Kling-Net-compatible products with the ÉPIX Drive 900, you can
control each individually on a single network.
Art-Net™
Connection
Art-Net™ is an Ethernet protocol that uses TCP/IP which transfers a large amount of DMX512
data using an Neutrik® etherCON® RJ45 connection over a large network. An Art-Net™
protocol document is available from www.chauvetprofessional.com.
Art-Net™ designed by and copyright Artistic Licence Holdings Ltd.
sACN
Connection
Also known as ANSI E1.31, Streaming-ACN is an Ethernet protocol that uses the layering and
formatting of Architecture for Control Networks to transport DMX512 data over IP or any other
ACN compatible network. ACN is maintained by the Professional Lighting and Sound
Association (PLASA).
Kling-Net
Connection
Kling-Net is a network protocol that allows auto configuration of display devices using a
Neutrik® etherCON® RJ45 Ethernet connection. Refer to the ArKaos software manual for
detailed instructions on programming this product.
For smooth-running operation, ArKaos Kling-Net requires a gigabit (1000 Mbps)
Ethernet card and network router.
Connection
Diagram
Never connect an ÉPIX product to the WAN port of a router.
Switch or Router
(such as the NET-Switch
from CHAUVET Professional)
ÉPIX Drive 900
Computer/Controller
(running Kling-Net, Art-
Net™,
or sACN protocol)
To other Kling-Net, Art-
Net™,
or sACN Devices

Setup
-8- ÉPIX Drive 900 User Manual Rev. 1
Connecting
ÉPIX Products
The ÉPIX Drive 900 uses a 4-pin XLR connection to link all ÉPIX Tour products. Each ÉPIX
Tour product must be daisy-chained together in series. Each ÉPIX Drive 900 is capable of
supporting up to 900 LEDs in seven possible configurations:
•18 ÉPIX Strip Tour
•15 ÉPIX Strip Tour and 1 ÉPIX Bar Tour
•12 ÉPIX Strip Tour and 2 ÉPIX Bar Tour
•9 ÉPIX Strip Tour and 3 ÉPIX Bar Tour
•6 ÉPIX Strip Tour and 4 ÉPIX Bar Tour
•3 ÉPIX Strip Tour and 5 ÉPIX Bar Tour
•6 ÉPIX Bar Tour
•The ÉPIX Drive 900 can support up to 18 ÉPIX Strip Tour products, 6 ÉPIX Bar Tour
products, or any of the combinations listed above.
•Make sure the total length of the connecting shielded 4-pin XLR cables does not
exceed 210 feet (64 meters). Using unshielded cables will increase the maximum
cable length to 300 feet (91 meters).
Most standard 4-pin XLR “Scroller” cables are shielded.
Length of cables between products must
not exceed 60 ft (18 m) when shielded,
or 100 ft (30 m) when unshielded
Length of cables between ÉPIX Drive 900 and 1st product must not
exceed 65 ft (20 m) when shielded, or 150 ft (45 m) when unshielded
Total length of cables cannot exceed 210 ft (64 m) when shielded,
or 300 ft (91 m) when unshielded
4-pin XLR Cable Diagram
1 = Power +
2 = Data +
3 = Data
-
4 = Power
-
(16 AWG or larger)
(18
–24 AWG)
(18
–24 AWG)
(16 AWG or larger)

Operation
ÉPIX Drive 900 User Manual Rev. 1 -9-
4. OPERATION
Control Panel
Description
Button
Function
<MENU/ESC>
Exits from the current menu or function or cycles through the main level
of the menu
<UP>
Navigates upward through the menu list or increases the numeric value
when in a function
<DOWN>
Navigates downward through the menu list or decreases the numeric
value when in a function
<ENTER>
Enables the currently displayed menu or sets the currently selected
value in to the current function
Menu Map
Main Level
Programming Levels
Description
Protocol
Art-Net
Selects the Ethernet protocol and determines
what other Menu options are available
Kling-Net
sACN
Auto Address
Yes
Automatically find and address the products
No
Display Inverse
Yes
Turn display 180 degrees
No
Start Universe
(Art-Net™ or sACN only)
0–250
(Art-Net)
Sets the lowest of the 6 consecutive Art-Net™
or sACN universes the product is assigned to
1-250
(sACN)
IP Address #1 to
IP Address #6
(Art-Net™ or sACN only)
x*.xxx.xxx.xxx Sets the IP addresses for the ÉPIX Drive 900
Note: The addresses cannot be the same
Device ID
xxxxxxxxxx
Shows device ID
View Linked Fixture
1. X** – 18. X**
Shows the connected products in order
LED Output
Off
Turn off all LED output
Red
Red LEDs at full
Green
Green LEDs at full
Blue
Blue LEDs at full
White
White LEDs at full
Fade
Color roll fade at full
Scroll
Rainbow roll at full
Factory Reset
Yes
Resets products to factory defaults
No
* - In Art-Net™ mode, the beginnings of the IP addresses can be set to 2 or 10, and
in sACN mode they can also be set to 239.
** - The display will show ÉPIX Strip tour, ÉPIX Bar Tour, or nothing.
Firmware V1.1

Operation
-10- ÉPIX Drive 900 User Manual Rev. 1
Ethernet
Configuration
The ÉPIX Drive 900 operates by routing one of three Ethernet protocols (Art-Net™, sACN, or
Kling-Net) to the ÉPIX Tour products linked to the output of the Drive. The Ethernet protocol
must be set for the products to respond correctly to the controller. See the Menu Map
for more
information on menu options.
Protocol
To configure the protocol for the ÉPIX Drive 900, follow the instructions below:
Press <MENU>repeatedly until Protocol shows on the display.1. Press <ENTER>.2. Use <UP> or <DOWN> to select Art-Net, Kling-Net, or sACN.3.
Press <ENTER>.4.
Start Universe
Each ÉPIX Drive 900 uses 6 consecutive universes in Art-Net™ mode and sACN mode, which
are assigned by setting the starting (lowest-numbered) universe address.
To set the address of the starting universe, do the following:
Press <MENU>repeatedly until Start Universe shows on the display.1. Press <ENTER>.2. Use <UP> or <DOWN> to select a starting universe address, 0–250 (for Art-Net™),3. or 1–250 (for sACN).
Press <ENTER>.4.
Each universe can support up to 3 ÉPIX Strip Tour products or 1 ÉPIX Bar Tour product.
Regardless of the order in which they are connected, ÉPIX Strip Tour products will be
grouped together, 3 to a universe.
IP Addresses
In Art-Net™ and sACN mode, the ÉPIX Drive 900 dedicates a separate IP address for each
universe. To set any of the 6 IP addresses in the ÉPIX Drive 900, follow the instructions below:
Press <MENU> repeatedly until IP Address #Xshows on the display.1. Press <ENTER>.2. Use <UP>or <DOWN> to set the highlighted number.3. Press <ENTER>.4.
Repeat steps 3-4 until the IP address is set as desired.5.
•The beginnings of the IP addresses can be set to 2 or 10 in Art-Net™ mode. In sACN
mode, they can also be set to 239. The beginnings of each IP address will always
match.
•The IP addresses cannot be identical.
Auto
Addressing
The ÉPIX Drive 900 addresses connected products with the Auto Address function. To perform
an Auto Address, do the following:
Press <MENU> repeatedly until Auto Address shows on the display.1. Press <ENTER>.2. Use <UP> or <DOWN> to select Yes.3.
Press <ENTER>.4.
Perform an Auto Address every time products are connected, disconnected, or
reconfigured, as soon as all changes have been made.
View Linked
Fixtures
To view all of the fixtures discovered by the Auto Addressing function, follow the instructions
below:
Press <MENU> repeatedly until View Linked Fixture shows on the display.1. Press <ENTER>.2.
Use <UP> or <DOWN> to scroll through the list of discovered products, 1–18.3.

Operation
ÉPIX Drive 900 User Manual Rev. 1 -11-
Home Screen
The ÉPIX Drive 900 has a home screen that displays the current protocol mode and
IP addresses, or the Output Test mode. This screen shows at start-up, and after
15 seconds
with no menu activity.
The home screen can also be viewed by pressing and holding <MENU> for 2 seconds.
Display
Orientation
To re-orient the display for easier reading in different mounting applications, do the following:
Press <MENU> repeatedly until Display Inverse shows on the display.1. Press <ENTER>.2. Use <UP> or <DOWN> to select Yes (for inverted) or No (for normal).3.
Press <ENTER>.4.
Device ID
To view the Device ID of the ÉPIX Drive 900:
Press <MENU>repeatedly until Device ID shows on the display.1.
Press <ENTER>.2.
LED Output
Test
Output Test mode allows the user to test each output of the ÉPIX Drive 900, as well as the
functionality of their ÉPIX Tour products. To run an output test:
Press <MENU>repeatedly until LED Output shows on the display.1. Press <ENTER>. The current test mode will begin to output.2. Use <UP> and <DOWN> to select one of seven output test modes: Red, Green, Blue,3. White, Fade, Scroll, or Off.
Press <ENTER>.4.
The ÉPIX Drive 900 will remain in Output Test mode until it receives a signal from a
controller. To stop
the color output without sending a signal to the product, set the LED
Output to Off.
Factory Reset
To reset the product to factory defaults:
Press <MENU>repeatedly until Factory Reset shows on the display.1. Press <ENTER>.2. Use <UP> or <DOWN> to select Yes.3.
Press <ENTER>.4.
After a Factory Reset, the ÉPIX Drive 900 will be set to Art-Net™ mode.

Technical Information
-12- ÉPIX Drive 900 User Manual Rev. 1
6. TECHNICAL INFORMATION
Product
Maintenance
To maintain optimum performance and minimize wear, you should clean this product frequently.
Usage and environment are contributing factors in determining the cleaning frequency.
As a rule, clean this product at least twice a month. Dust build-
up reduces light output
performance and can cause overheating. This can lead to reduc
ed light source life and
increased mechanical wear.
To clean your product:
Unplug the product from power.1. Wait until the product is at room temperature.2. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the3. external vents.
Clean all external surfaces with a mild solution of non-ammonia glass cleaner or isopropyl4. alcohol.
Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.5. Wipe any dirt or grime to the outside edges of the lens surface.6.
Gently polish the lens surfaces until they are free of haze and lint.7.
Always dry the external surfaces thoroughly and carefully after cleaning them.
Do not spin the cooling fans by blowing compressed air into them.

Technical Specifications
ÉPIX Drive 900 User Manual Rev. 1 -13-
7. TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
19 in (483 mm)
7.6 in (193 mm)
2 in (50 mm)
5.4 lb (2.5 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100–240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 VAC, 60 Hz
208 VAC, 60 Hz
230 VAC, 50 Hz
Consumption
299 W
299 W
299 W
Current
2.53 A
1.44 A
1.31 A
Power linking current (products)
13.6 A (6 products)
13.6 A (11 products)
13.6 A (12 products)
Fuse/Breaker
T 5 A, 250 V
T 5 A, 250 V
T 5 A, 250 V
Power I/O
U.S./Canada
Worldwide
Power input connector
Neutrik® powerCON® A
Neutrik® powerCON® A
Power output connector
Neutrik® powerCON® B
Neutrik® powerCON® B
Power cord plug
Edison (U.S.)
Local plug
ÉPIX Product Output
Output Connector
Output Voltage
4-pin XLR
48 VDC
ÉPIX Product
Maximum Load Per Drive
LEDs Per Product
ÉPIX Strip Tour
18 products
50
ÉPIX Bar Tour
6 products
150
any combination up to 900 LEDs
Maximum Cable
Lengths
Shielded
Unshielded
From Drive to 1st ÉPIX product
65 ft (20 m)
150 ft (45 m)
Between ÉPIX products
60 ft (18 m)
100 ft (30 m)
Total from Drive through all
ÉPIX products
210 ft (64 m) 300 ft (91 m)
Art-Net™ and sACN
I/O Connector
Channel Range
Amphenol XLRnet
2700
ArKaos Kling-Net
I/O Connector
Channel Range
Amphenol XLRnet
Determined per ArKaos
MediaMaster software
Thermal
Max. External Temperature
Cooling System
113 °F (45 °C)
Fan-Assisted Convection

Technical Specifications
-14- ÉPIX Drive 900 User Manual Rev. 1
Ordering
Product Name
Item Name
Item Code
UPC Number
ÉPIX Products
ÉPIX Drive 900
EPIXDRIVE900
03091141
781462214890
ÉPIX Strip Tour
EPIXSTRIPTOUR
03091139
781462214876
ÉPIX Bar Tour
EPIXBARTOUR
03091140
781462214883
Accessories
ÉPIX Strip Tour Dome
Accessory (4 pieces)
EPIXSTRIPDOME 03091142 781462214906
4-pin XLR Cables
4-pin XLR Extension
Cable, 16 in
4PINEXT16IN 19111143 781462214913
4-pin XLR Extension
Cable, 5 ft
4PINEXT5FT 19111144 781462214920
4-pin XLR Extension
Cable, 50 ft
4PINEXT50FT 19111147 781462214951
etherCON Cables
Neutrik® etherCON®
Extension Cable, 18 in
ETHERCONEXT18IN 19090363 781462207151
Neutrik® etherCON®
Extension Cable, 5 ft
ETHERCONEXT5FT 19090364 781462207168
Neutrik® etherCON®
Extension Cable, 10 ft
ETHERCONEXT10FT 19090365 781462207175
Neutrik® etherCON®
Extension Cable, 25 ft
ETHERCONEXT25FT 19090366 781462207182
Neutrik® etherCON®
Extension Cable, 50 ft
ETHERCONEXT50FT 19090367 781462207199
powerCON Cables
Neutrik® powerCON®
Extension Cable, 18 in
POWERCONEXT18IN 19110372 781462207243
Neutrik® powerCON®
Extension Cable, 5 ft
POWERCONEXT5FT 19110373 781462207250
Neutrik® powerCON®
Extension Cable, 10 ft
POWERCONEXT10FT 19110374 781462207267
Neutrik® powerCON®
Extension Cable, 25 ft
POWERCONEXT25FT 19110375 781462207274
Neutrik® powerCON®
Extension Cable, 50 ft
POWERCONEXT50FT 19110376 781462207281
For the most current list of related products and accessories available from CHAUVET
Professional, visit our website at www.chauvetprofessional.com.

User Manual
ÉPIX Drive 900 User Manual Rev. 1 -15-
R
ETURNS
In case you need to get support or return a product:
•If you are located in the U.S., contact Chauvet World Headquarters.
•If you are located in the UK or Ireland, contact Chauvet Europe Ltd.
•If you are located in Mexico, contact Chauvet Mexico.
•If you are located in Benelux, contact Chauvet Europe BVBA.
If you are located in any other country, DO NOT contact Chauvet. Instead, contact your local
distributor. See www.chauvetlighting.com
for distributors outside the U.S., UK, Ireland, Mexico,
or Benelux.
If you are located outside the U.S., UK, Ireland, Mexico, or Benelux, contact your
distributor of record and follow their instructions on how to return Chauvet products to
them. Visit our website www.chauvetlighting.com for contact details.
Call the corresponding Chauvet Technical Support office and request a Return Merchandise
Authorization (RMA) number before shipping the product. Be prepared to provide the model
number, serial number, and a brief description of the cause for the return.
Send the merchandise prepaid, in its original box, and with its original packing
and accessories.
Chauvet will not issue call tags.
Clearly label the package with the RMA number. Chauvet will refuse any product returned
without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write the following information on a piece of paper and place
it inside the box:
•Your name
•Your address
•Your phone number
•RMA number
•A brief description of the problem
Be sure to pack the product properly. Any
shipping damage resulting from inadequate
packaging will be your responsibility. FedEx packing or double-boxing are recommended.
Chauvet reserves the right to use its own discretion to repair or replace returned
product(s).

User Manual
ÉPIX Drive 900 User Manual Rev. 1
C
ONTACT
US
USA WORLD HEADQUARTERS
General Information – Chauvet
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [e-mail]
World Wide Web www.chauvetlighting.com
EUROPE
General Information - Chauvet Europe BVBA
Address: Stokstraat 18
9770 Kruishoutem
Belgium
Voice: [phone]
Technical Support
Email: [e-mail]
World Wide Web www.chauvetlighting.eu
General Information - Chauvet Europe Ltd.
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Email: [e-mail]
World Wide Web www.chauvetlighting.co.uk
MEXICO
General Information - Chauvet Mexico
Address: Av. Santa Ana 30
Parque Industrial Lerma
Lerma, Mexico C.P. 52000
Voice: [phone]
Technical Support
Email: [e-mail]
World Wide Web www.chauvet.com.mx
Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux contact the dealer of record.
Follow their instructions to request support or to return a product. Visit our website for contact
details.