Chauvet Professional GROUND SUPPORT 2 KIT User manual

Quick Reference Guide
English EN
Español ES
Français FR
Deutsch DE
Nederlands NL
GROUND SUPPORT 2 KIT

1
EN
QUICK REFERENCE GUIDE
Ground Support 2 Kit QRG Rev. 1
About This Guide
The Ground Support 2 Kit Quick Reference Guide (QRG) has basic product information such as mounting diagrams and
technical specifications.
Disclaimer
The information and specifications contained in this QRG are subject to change without notice.
LIMITED WARRANTY
FOR WARRANTY REGISTRATION AND COMPLETE TERMS AND CONDITIONS PLEASE VISIT OUR WEBSITE.
For Customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration.
For Customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, and
Germany: www.chauvetlighting.eu/warranty-registration.
Chauvet warrants that this product shall be free from defects in material and workmanship under normal use, for the
period specified in, and subject to the exclusions and limitations set forth in the full limited warranty on our website. This
warranty extends only to the original purchaser of the product and is not transferable. To exercise rights under this
warranty, you must provide proof of purchase in the form of an original sales receipt from an authorized dealer that shows
the product name and date of purchase. THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES. This
warranty gives you specific legal rights. You may also have other rights that vary from state to state and country to
country. This warranty is valid only in the United States, United Kingdom, Republic of Ireland, Belgium, the Netherlands,
Luxembourg, France, Germany and Mexico. For warranty terms in other countries, please consult your local distributor.
Safety Notes
These Safety Notes include important information about installation, use, and maintenance.
• This product contains no user-serviceable parts.
• When selecting an installation location, consider ease of access for operation and routine maintenance of attached
panels.
• Make sure that the floor structure is stable and immobile.
• DO NOT use the kit if any welded joints are cracked or appear damaged in any way.
• The ballast weights stated in this specification are for indoor usage only. If this kit is used outdoors, the unit must
be protected from wind and additional ballast (as determined by a qualified and competent rigger) must be used.
Contact
Outside the US, United Kingdom, Ireland, Benelux, France, Germany, or Mexico contact your distributor to request
support or return a product. Visit www.chauvetprofessional.com for contact information.
What is Included
• Floor Base (x2)
• Angling Horizontal Bar (x2)
• Angling 1M Pipe with 2 clamps (x3)
• 1M Ladder Truss with Spigots, Pins, and Safety Clips (x6)
• Panel Attachment Arm (x6)
• TR16 Screw Jacks (x10)
• M12 Panel Attachment Screws (x12)
• Quick Reference Guide
The Ground Support 2 Kit is shipped in the road case.

EN
2
Ground Support 2 Kit QRG Rev. 1
QUICK REFERENCE GUIDE
Product Description
The Ground Support 2 Kit is a complete ground support solution for stacking F-Series Video Panels as a video wall on the
floor. Multiple kits can be used to stack wider video walls. The Ground Support 2 Kit can accommodate flat and concave
video walls, including a 5° or 10° curve (kit sold separately). The DRB-F100CM or DRB-F50CM dual function rig bars are
required for operation.
Product Overview
Panel Attachment Arm (x6)
Floor Base (x2)
Angling Horizontal Bar (x2)
Angling 1M Pipe
with 2 clamps (x3)
1M Ladder Truss (x6)

3
EN
QUICK REFERENCE GUIDE
Ground Support 2 Kit QRG Rev. 1
Product Dimensions
10.24 ft
3.12 m
3.28 ft
1 m 3.28 ft
1 m

EN
4
Ground Support 2 Kit QRG Rev. 1
QUICK REFERENCE GUIDE
Mounting
Before mounting this product, read the Safety Notes, as well as those for the attached products.
Mounting Diagram
Mounting Procedure
1. Insert TR16 Screw Jack into the bottom of the dual function F-series rig bar panel.
2. Align the floor base panel with the female speego connection on the rig bar.
3. Use the tightening nut to adjust the height of the rig bar and floor base panel. Verify they are level with the
surface.
4. Turn the locking nut on the screw jacks to secure the position.
Dual-function F-series
Rig Bar
Floor Base
TR16 Screw Jacks
Male Speego
connection
Dual-function F-series
Rig Bar
Female Speego
connection
Locking Nut
Tightening Nut

5
EN
QUICK REFERENCE GUIDE
Ground Support 2 Kit QRG Rev. 1
5.
Connect the ladder truss to the floor base and insert the spigots and safety clip (be sure to insert the spigots correctly) .
6. Repeat steps with additional floor base and connect the two floor base panels with the angling horizontal bars.
Locking Spigots
Ladder Truss
Angling horizontal bars

EN
6
Ground Support 2 Kit QRG Rev. 1
QUICK REFERENCE GUIDE
7. Place ballast weights (sandbags or steel weights) over the angling horizontal bars.
8. Attach the F-series video panel to the rig bar panel by aligning the magnetic alignment conicals and locking the
male connection speegos.
9. Insert the M12 panel attachment screws into the appropriate M12 threaded mounting hole.
The F2 and F5IP video panels have frames with a center mounting position. The F3 video panel will
need the panel attachment screw inserted at the corner of the frame. Both the F4IP and Vivid 4 have
been upgraded with center mounting position frames, and may vary depending on order date.
M12 Panel
Attachment Screws
Video Panel

7
EN
QUICK REFERENCE GUIDE
Ground Support 2 Kit QRG Rev. 1
M12 Panel
Attachment Screws
Center Mount Position
Corner Mount Position
M12 Panel
Attachment Screws

EN
8
Ground Support 2 Kit QRG Rev. 1
QUICK REFERENCE GUIDE
10. Place the panel attachment arm over the panel attachment screw(s) and move down to secure.
11. Secure the clamp of the panel attachment arm to the ladder truss.
The panel attachment arm is adjustable depending on the type of video panel being attached. If the
attachment arm is connected to the center mounting position, it will need to be extended to the third
locking level. If connecting to the corner mounting position, the second locking level must be used. If
using the curve kit on your video panel, use the first locking level to shorten the panel attachment arm.
M12 Panel
Attachment Screws Panel Attachment Arm
321

9
EN
QUICK REFERENCE GUIDE
Ground Support 2 Kit QRG Rev. 1
12. Continue to stack the ladder truss and video panels for the desired video wall size.
Supports walls between 4.92 ft (1.5 m) and 8.2 ft (2.5 m) wide, and as high as 9.85 ft (3 m) tall. Combine
additional Ground Support 2 Kits to achieve wider walls.
!