Chauvet Professional Ovation H-265WW User manual

User Manual

Ovation H-265WW User Manual Rev. 1
EDITION NOTES
The Ovation H-265WW User Manual includes a description, safety precautions, installation, programming,
operation and maintenance instructions for the Ovation H-265WW as of the release of this edition.
Trademarks
CHAUVET, the Chauvet logo and Ovation H-265WW are registered trademarks or trademarks of Chauvet
& Sons, LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other
company and product names and logos referred to herein may be trademarks of their respective
companies.
Copyright Notice
The works of authorship contained in this manual, including, but not limited to, all design, text and images
are owned by Chauvet.
© Copyright 2018 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
Manual Use
Chauvet authorizes its customers to download and print this manual for professional information purposes
only. Chauvet expressly prohibits the usage, copy, storage, distribution, modification, or printing of this
manual or its content for any other purpose without written consent from Chauvet.
Document Printing
For best results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If using A4
paper (210 x 297 mm), configure the printer to scale the content accordingly.
Intended Audience
Any person installing, operating, and/or maintaining this product should completely read through the guide
that shipped with the product, as well as this manual, before installing, operating, or maintaining this
product.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects. However,
Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss,
damage or disruption caused by any errors or omissions in this document, whether such errors or
omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the
content of this document without any obligation to notify any person or company of such revision, however,
Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest
version from www.chauvetprofessional.com
Document Revision
This Ovation H-265WW User Manual is the 1st edition of this document. Go to
www.chauvetprofessional.com for the latest version.

Ovation H-265WW User Manual Rev. 1
TABLE OF CONTENTS
TOC 1 of 2
TABLE OF CONTENTS
1. Before You Begin ....................................................................... 3
What Is Included ........................................................................................... 3
Claims ........................................................................................................... 3
Manual Conventions ..................................................................................... 3
Symbols ........................................................................................................ 3
Safety Notes.................................................................................................. 4
Personal Safety.............................................................................................................. 4
Mounting and Rigging .................................................................................................... 4
Power and Wiring........................................................................................................... 4
Operation ...................................................................................................... 4
Expected LED Lifespan................................................................................. 4
2. Introduction ................................................................................ 5
Description .................................................................................................... 5
Features........................................................................................................ 5
Product Overview.......................................................................................... 6
Product Dimensions ...................................................................................... 7
3. Setup ........................................................................................... 8
AC Power...................................................................................................... 8
AC Plug .......................................................................................................................... 8
Fuse Replacement ......................................................................................................... 8
DMX Linking.................................................................................................. 9
DMX Personalities.......................................................................................................... 9
Master/Slave Connectivity............................................................................. 9
DMX Linking................................................................................................................... 9
Master/Slave Connection ............................................................................................... 9
RDM (Remote Device Management) ............................................................................. 9
Wireless Operation......................................................................................................... 9
Initial Setup .................................................................................................................... 9
Configuration.................................................................................................................. 10
Product Pairing............................................................................................................... 10
Mounting ....................................................................................................... 10
Orientation...................................................................................................................... 10
Rigging ........................................................................................................................... 10
Procedure....................................................................................................................... 11
4. Operation .................................................................................... 12
Control Panel Operation................................................................................ 12
Control Options ............................................................................................. 12
Programming................................................................................................. 12
Menu Map ..................................................................................................... 12
Configuration (DMX) ..................................................................................... 13
DMX Personalities.......................................................................................................... 13
DMX Control................................................................................................................... 13
Configuration (Standalone) ............................................................................................ 15
Static Mode .................................................................................................................... 15
Auto Programs ............................................................................................................... 15
Master/Slave .................................................................................................................. 15
Dimmer Profiles.............................................................................................................. 15
LED Frequency .............................................................................................................. 15
Back Light ...................................................................................................................... 16
Wireless Settings ........................................................................................................... 16
System Information ........................................................................................................ 16
Emergency Mode ........................................................................................................... 16

TABLE OF CONTENTS
Ovation H-265WW User Manual Rev. 1
TOC 2 of 2
Reset Factory................................................................................................................. 16
5. Technical Information ................................................................ 17
Product Maintenance .................................................................................... 17
6. Technical Specifications ........................................................... 18
Photometrics Chart 750 W ............................................................................................. 19
Returns........................................................................................ 21
Contact Us .................................................................................. 22

Page 3 of 22
Ovation H-265WW User Manual Rev. 1
BEFORE YOU BEGIN
1. BEFORE YOU BEGIN
What Is Included
Claims
Carefully unpack the product immediately and check the container to make sure all the parts are in the
package and are in good condition.
If the box or the contents (the product and included accessories) appear damaged from shipping, or show
signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier
immediately may invalidate your claim. In addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or concealed
damage, file a claim with Chauvet within 7 days of delivery.
Manual Conventions
Symbols
• Ovation H-265WW
• 45° and 25° Lenses
• Warranty Card
• Quick Reference Guide
Convention Meaning
1–512 A range of values
50/60 A set of values of which only one can be chosen
<SET> A button on the product’s control panel
Settings A product function or a menu option
Symbol Meaning
Electrical warning. Not following these instructions may cause electrical damage to
the product, accessories, or the user.
Critical installation, configuration, or operation information. Not following these
instructions may make the product not work, cause damage to the product, or cause
harm to the operator.
Important installation or configuration information. The product may not function
correctly if this information is not used.
Useful information.
Any reference to data or power connections in this manual assumes the use of
Seetronic IP rated cables.
The term “DMX” used throughout this manual refers to the USITT DMX512-A
digital data transmission protocol.
!
!

Page 4 of 22
BEFORE YOU BEGIN
Ovation H-265WW User Manual Rev. 1
Safety Notes
Read all the following safety notes before working with this product. These notes contain important
information about the installation, usage, and maintenance of this product.
Personal Safety
• Avoid direct eye exposure to the light source while the product is on.
• Always disconnect the product from the power source before cleaning or replacing the fuse.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Do not touch the product’s housing when operating because it may be very hot.
Mounting and Rigging
• This product is not intended for permanent installation.
• This product is for indoor use only! To prevent risk of fire or shock, do not expose this product to
rain or moisture. (IP20)
• CAUTION: When transferring product from extreme temperature environments, (e.g. cold truck to
warm humid ballroom) condensation may form on the internal electronics of the product. To avoid
causing a failure, allow product to fully acclimate to the surrounding environment before connecting
it to power.
• Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent
surfaces.
• Make sure there are no flammable materials close to this product while it is operating.
• When hanging this product, always secure to a fastening device using a safety cable.
• Never carry the product by the power cord.
Power and Wiring
• Make sure the power cord is not crimped or damaged.
• Always make sure you are connecting this product to the proper voltage in accordance with the
specifications in this manual or on the product’s specification label.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
• Never connect this product to a dimmer pack or rheostat.
• Make sure to replace the fuse with another of the same type and rating.
• Never disconnect this product by pulling or tugging on the power cable.
Operation
• Do not operate this product if there is damage on the housing, lenses, or cables. Have the damaged
parts replaced by an authorized technician at once.
• Do not cover the ventilation slots when operating to avoid internal overheating.
• The maximum ambient temperature is 113 °F (45 °C). Do not operate the product at higher temperatures.
• In the event of a serious operation problem, stop using this product immediately!
Expected LED Lifespan
LEDs gradually decline in brightness over time, primarily because of heat. LEDs that are arranged in
clusters experience higher operating temperatures than single LEDs. For this reason, operating clustered
LEDs at their fullest intensity significantly reduces the LEDs’ lifespan. Under normal conditions, this
lifespan is 40,000 to 50,000 hours. If extending this lifespan is vital, lower the operating temperature by
improving the ventilation around the product, thus reducing the ambient temperature. In addition, limiting
the overall projection intensity may extend the LEDs’ lifespan.
This product contains no user-serviceable parts. Any reference to servicing in
this User Manual will only apply to properly trained, certified technicians. Do not
open the housing or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this
product.
If your Chauvet product requires service, contact Chauvet Technical Support.
!

Page 5 of 22
Ovation H-265WW User Manual Rev. 1
INTRODUCTION
2. INTRODUCTION
Description
The Ovation H-265WW is a silent, convention cooled LED house light with a warm white light output and a
CRI.The unit also features 16-bit dimming, RDM and W-DMX control as well as adjustable PWM to prevent
flickering on televised performances. Interchangeable lenses for height adjustment are another feature in
theatrical and house of worship applications. For even more versatility, the yoke can be completely
removed, and the fixture suspended, pendant style, from a loop on the back plate. Available in black or
white.
Features
• High-power warm white, convection cooled house light
• Interchangeable lens plates to adapt to different mounting heights
• 5-pin XLR and terminal blocks for DMX connections
• Use included yoke for
• mounting, or suspend from integrated loop-eye
• 16-bit dimming for ultra-smooth fades
• DMX, WDMX and RDM (Remote Device Management) for added programming flexibility
• Adjustable PWM (Pulse Width Modulation) to avoid flickering on camera

Page 6 of 22
INTRODUCTION
Ovation H-265WW User Manual Rev. 1
Product Overview
Safety Loop/
Pendent Mounting
Power Input
Yoke
Adjustment
Control Panel
Alternate DMX
Data Connection
DMX Data
Connection
Fuse
Safety Loop
Menu buttons

Page 7 of 22
Ovation H-265WW User Manual Rev. 1
INTRODUCTION
Product Dimensions
10 in
254 mm
9.4 in
240 mm
13.1 in
333 mm
13.34 in
339 mm

Page 8 of 22
SETUP
Ovation H-265WW User Manual Rev. 1
3. SETUP
AC Power
Each Ovation H-265WW has an auto-ranging power supply that works with an input voltage range of 100
to 240 VAC, 50/60 Hz. To determine the power requirements for each Ovation H-265WW, refer to the label
affixed to the product. You can also refer to the Technical Specifications chart in this manual.
The listed current rating indicates the maximum current draw during normal operation. For more
information, download Sizing Circuit Breakers from the Chauvet website: www.chauvetprofessional.com.
AC Plug
The Ovation H-265WW comes with a bare ended power input cord. The product side of this power cord
enters the product through a strain reliever (rubber boot) and it cannot be disconnected from the product.
Use the table below to wire the plug to the power cord.
Fuse Replacement
1. Disconnect this product from the power outlet.
2. Using a flat-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove the blown fuse and replace with another fuse of the same type and rating
(T 3.15 A, 250 V).
4. Screw the fuse holder cap back in place and reconnect power.
• Always connect the product to a protected circuit (circuit breaker or fuse). Make
sure the product has an appropriate electrical ground to avoid the risk of
electrocution or fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-
use completely disconnect the product from power via breaker or by unplugging
it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if
the rheostat or dimmer channel serves only as a 0 to 100% switch.
Connection Wire (U.S.) Wire (Europe) Screw Color
AC Live Black Brown Yellow or Brass
AC Neutral White Blue Silver
AC Ground Green/Yellow Green/Yellow Green
The Ovation H-265WW includes a 15 ft., (4.5 m) cable attached to allow for pendent
mounting
Make sure to disconnect the product’s power cord before replacing a blown fuse.
Always replace the blown fuse with another of the same type and rating.
!
!

Page 9 of 22
Ovation H-265WW User Manual Rev. 1
SETUP
DMX Linking
You can link the Ovation H-265WW to a DMX controller using a 3- and 5-pin DMX connection or hard
wiring using the Phoenix connector. If using other DMX-compatible products with this product, you can
control each individually with a single DMX controller.
DMX Personalities
The Ovation H-265WW uses a DMX data connection for the 1-,2-, or 5-Ch DMX personalities.
• Refer to the Introduction for a brief description of each DMX personality.
• Refer to the Operation chapter to learn how to configure the Ovation H-265WW to work in these
personalities.
• The DMX Values section provides detailed information regarding the DMX personalities.
Master/Slave Connectivity
The Master/Slave mode allows a Ovation H-265WW (the master) to control one or more Ovation H-
265WW products (the slaves) without a DMX controller. One Ovation H-265WW becomes the master
when running an auto or custom program, or by being in a Static mode.
You must configure each slave’s control panel to operate in Slave mode. During Master/Slave operation,
the slaves will operate in unison with the master.
DMX Linking
The Ovation H-265WW will work with a DMX controller using a 5-pin DMX serial or a hard wire connection.
A DMX Primer is available from www.chauvetprofessional.com.
DMX Connection
The Ovation H-265WW uses a 5-pin DMX or a hard wire data connection for its DMX personalities: 1, 2 or
5. See the User Manual for information about connecting and configuring the product for DMX operation.
Master/Slave Connection
The Ovation H-265WW uses the DMX data connection for its Master/Slave mode. See the User Manual for
information about how to connect and configure the product for master/slave operation.
RDM (Remote Device Management)
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate
bi-directionally along existing DMX cabling. The Ovation H-265WW supports RDM protocol that allows
feedback to monitor temperature and changes to DMX Address, DMX Personality, Dimmer Mode, and
LED Frequency menu options. Download the User Manual from www.chauvetprofessional.com for more
details.
Wireless Operation
In optimal conditions, the Ovation H-265WW can operate up to 300 m (900 ft) away from the W-DMX
transmitter. The W-DMX receiver in the Ovation H-265WW must be paired with the W-DMX transmitter for
wireless operation.
Initial Setup
1. Turn the W-DMX transmitter on.
2. Connect the W-DMX transmitter to a DMX controller.
3. Place the Ovation H-265WW within 300 m from the W-DMX transmitter.
4. Disconnect any DMX cable from the Ovation H-265WW.
5. Turn the Ovation H-265WW on.
DO NOT connect a DMX controller to products operating in Master/Slave mode. The
DMX controller signals may interfere with the signals from the master.
•The Operation section of this manual provides detailed instructions on how to
configure the master and slaves.
• If you are not familiar with DMX standards or Master/Slave connectivity,
download the DMX Primer from the Chauvet website
www.chauvetprofessional.com for more information.

Page 10 of 22
SETUP
Ovation H-265WW User Manual Rev. 1
Configuration
1. From the Ovation H-265WW control panel, go to DMX Address.
2. Select the start address, as with any other DMX compatible product.
3. Go to Wireless Setting > Receive On/Off.
4. Select On. (The Signal Strength Indicator will show a ? in front of the bars)
5. Press the reset button on the W-DMX transmitter. (The Signal Strength Indicator on the Ovation
H-265WW will show a ϟ in front of the bars for 3 seconds while a connection is established.
Product Pairing
If the Ovation H-265WW has already been paired with the W-DMX transmitter, the Signal Strength
Indicator in the middle of the LCD screen will show the strength of the signal. In this case, the Ovation H-
265WW is ready to work in Wireless mode. Pairing the Ovation H-265WW and a new W-DMX transmitter:
1. From the Ovation H-265WW control panel, go to Wireless Setting.
2. Select the Receive Reset. The Signal Strength Indicator on the Ovation H-265WW will show a ?
in front of the bars.
3. From the W-DMX transmitter, press <RESET> (the Signal Indicator on the transmitter will flash).
4. Once the transmitter has found the Ovation H-265WW, the Signal indicator on the W-DMX
transmitter will illuminate solid.
5. The Signal Strength Indicator in the middle of the LCD screen on the Ovation H-265WW will show
the strength of the signal.
Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.
For our CHAUVET Professional line of mounting clamps, go to http://trusst.com/products/.
Orientation
Always mount this product in a safe position, making sure there is adequate room for ventilation,
configuration, and maintenance.
Rigging
Chauvet recommends using the following general guidelines when mounting this product.
• Before deciding on a location for the product, make sure there is easy access to the product for
maintenance and programming purposes.
• Make sure that the structure onto which you are mounting the product can support the product’s
weight. See the Technical Specifications for weight information.
• When mounting the product overhead, always use a safety cable. Mount the product securely to a
rigging point, whether an elevated platform or a truss.
• When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.
• When power linking multiple products, mount the products close enough for power linking cables to
reach.
• The bracket adjustment knobs allow for directional adjustment when aiming the product to the
desired angle. Only loosen or tighten the bracket knobs manually. Using tools could damage the
knobs.
W-DMX operation can be interrupted or inhibited by liquid masses between the
transmitter and receiver such as water, snow, or people. For best results, keep the area
between the transmitter and receiver clear of any liquid mass.
!

Page 11 of 22
Ovation H-265WW User Manual Rev. 1
SETUP
Procedure
The Ovation H-265WW comes with a double-bracketed yoke to which you can either attach mounting
clamps for hanging or simply use as a floor stand. You must supply the mounting clamps. Make sure the
clamps are capable of supporting the weight of this product. Use at least one mounting point per product.
For the CHAUVET Professional line of mounting clamps, go to http://www.trusst.com/products.
Mounting Diagram
Mounting Clamp
Overhead Mounting
Safety Cable
Pendent Mounting

Page 12 of 22
OPERATION
Ovation H-265WW User Manual Rev. 1
4. OPERATION
Control Panel Operation
Control Options
Set the Ovation H-265WW starting address in the 001-512 DMX range. This enables control of up to 102
products in the 5-channel personality.
Programming
Refer to the Menu Map to understand the menu options. The menu map shows the main level and a
variable number of programming levels for each option.
• To go to the desired main level, press <MENU> repeatedly until the option shows on the display.
Press <ENTER> to select. This will take you to the first programming level for that option.
• To select an option or value within the current programming level, press <UP> or <DOWN> until
the option shows on the display. Press <ENTER> to select. In this case, if there is another
programming level, you will see that first option, or you will see the selected value.
• Press <MENU> repeatedly to exit to the previous main level.
Menu Map
Button Function
<MENU> Exits from the current menu or function
<ENTER> Enables the currently displayed menu or sets the currently selected value into the
selected function
<UP> Navigates upwards through the menu list or increases the numeric value when in a
function
<DOWN> Navigates downwards through the menu list or decreases the numeric value when in a
function
Main Level Programming Levels Description
DMX Address Address 001-508 Selects the starting address
DMX Channel
1Ch 1-channel: dimmer
2Ch 2-channel: dimmer, strobe
5Ch
5-channel: dimmer, strobe, auto
programs, auto speed, dimmer
speed
Static Dimmer 000-255 Controls intensity
Strobe 000-255 Controls strobe rate
Auto Show
Auto 1
001-100 Selects automatic programs and
auto program speed
Auto 2
Auto 3
Master/Slave Master Master mode
Slave Slave mode
Dimmer Mode
Off No dimmer
Dimmer 1 Dimming curves Dimmer 1 (fast)
to Dimmer 3 (slow)
Dimmer 2
Dimmer 3
LED
Frequency
600Hz
Selects the PWM output
frequency
1200Hz
2000Hz
4000Hz
6000Hz
25KHz

Page 13 of 22
Ovation H-265WW User Manual Rev. 1
OPERATION
Configuration (DMX)
Use DMX configurations to operate the product with a DMX controller.
DMX Personalities
This setting allows you to choose a particular DMX personality.
1. Go to the DMX Channel main level.
2. Select the desired personality (1CH, 2CH, or 5CH).
DMX Control
In this mode, each product will respond to a unique starting address from the DMX controller. All products
with the same starting address will respond in unison.
1. Select a DMX personality as shown in DMX Personalities.
2. Set the starting address:
a. Go to DMX Address main level.
b. Select the starting address (001–508).
The highest recommended starting address for each DMX mode is as follows:
Back Light
On Display backlight always on
10S Turns off display backlight after
10 sec of inactivity
20S Turns off display backlight after
20 sec of inactivity
30S Turns off display backlight after
30 sec of inactivity
Wireless
Setting
Receive On/Off On Turns on the wireless setting
Off Turns wireless DMX function off
Receive Reset
No Turns on the wireless setting
Yes No action is taken when DMX
signal is lost.
Emergency
mode
On Turns product on when DMX
signal is lost
Off No action is taken when DMX
signal is lost
Information
Fixture Hours _ _ _ _ Shows total product hours
Version V_._-V_ _ Shows installed software version
UID: _ _ _ _ _ _ _ _ _ _ _ _ Shows product UID
Reset Factory No Reset to factory defaults
Yes
Make sure that the starting addresses on the various products do not overlap
due to the new personality setting.
DMX Personality DMX Address
5498
2500
1501
Main Level Programming Levels Description

Page 14 of 22
OPERATION
Ovation H-265WW User Manual Rev. 1
DMX Values
1Ch
2Ch
5Ch
Channel Function Value Percent/Setting
1 Dimmer 000 255 0–100%
Channel Function Value Percent/Setting
1Dimmer000 000 0-100%
2Strobe
000 010 No function
011 255 Strobe, slow to fast
Channel Function Value Percent/Setting
1Dimmer000 255 0-100%
2Strobe
000 010 No function
011 255 Strobe, slow to fast
3Auto
programs
000 015 No function
016 095 Auto program 1
096 175 Auto program 2
176 255 Auto program 3
4 Auto Speed 000 255 0-100%
5Dimmer
Speed Mode
000 051 No function
052 101 Linear dimmer
102 152 Nonlinear dimming curve 1 (fastest)
153 203 Nonlinear dimming curve 2
204 255 Nonlinear dimming curve 3 (slowest)

Page 15 of 22
Ovation H-265WW User Manual Rev. 1
OPERATION
Configuration (Standalone)
Use standalone configuration to operate the product without a DMX controller.
Static Mode
The Manual Static mode allows for manual control of intensity and strobe rate without a DMX controller.
1. Go to the Static main level.
2. Select the Dimmer programming level.
3. Select the desired intensity value 0–255.
4. Go to the Strobe programming option.
5. Select the desired strobe rate value 0–255
Auto Programs
Auto programs allow for standalone dynamic mixing without a DMX controller.
1. Go to the Auto Show main level.
2. Select the desired auto Auto 1-3.
3. Select the desired speed Speed 001-100.
Master/Slave
The Master/Slave mode allows a group of Ovation H-265WW products (the slaves) to simultaneously
duplicate the output of another Ovation H-265WW (the master) without a DMX controller.
To set each of the slaves:
1. Go to the Master/Slave main level.
2. Select Slave.
To set the master:
1. Go to the Master/Slave main level.
2. Select Master.
3. Select an auto program as explained in Auto Programs.
Dimmer Profiles
This setting determines how fast the output of the Ovation H-265WW changes when you modify the values
of the white, and dimmer faders. This setting provides four different options to
1. Go to the Dimmer Mode main level.
2. Select a dimmer curve OFF, Dimmer 1, Dimmer 2, or Dimmer 3.
LED Frequency
This option changes the Pulse Width Modulation (PWM) frequency of the LEDs on the Ovation H-265WW.
1. Go to the LED Frequency main level.
2. Select PWM Frequency (600Hz, 1200Hz, 2000Hz, 4000Hz, 6000Hz, or 25Khz).
The auto programs cannot be edited.
• Do not connect a DMX controller to the products configured for Master/
Slave operation. The DMX controller may interfere with signals from the
master.
• The master should be the first product in the daisy chain.
• The master is the one that runs a program whether in Auto Show or Static
modes.
• Do not connect a DMX controller to the products configured for Master/
Slave operation. The DMX controller may interfere with signals from the
master.
• The master should be the first product in the daisy chain.

Page 16 of 22
OPERATION
Ovation H-265WW User Manual Rev. 1
Back Light
This setting allows for selection of the amount of time the back light on the Ovation H-265WW’s display
stays on after the last button is pressed on the control panel.
1. Go to the Back Light main level.
2. Select On (remains on), 10S (10 seconds), 20S (20 seconds), or 30S (seconds).
Wireless Settings
This mode allows the product to be used wirelessly. For detailed setup of this feature see Wireless
Operation. To disable this feature:
1. Go to Wireless Setting
2. Select Receive On/Off or Receive Reset.
3. Press Enter on the desired setting.
System Information
This option displays the total number of hours the product has run, and the installed software version.
1. Go to the Information main level.
2. Select Fixture Hours, Version or the product’s UID.
Emergency Mode
This feature can be set to turn on the Ovation H-265WW in the event DMX signal is lost.
1. Go to the Emergency Mode main level.
2. Select On or Off.
Reset Factory
This option restores the Ovation H-265WW to the original factory settings.
1. Go to the Reset Factory main level.
2. Select Yes or No.

Page 17 of 22
Ovation H-265WW User Manual Rev. 1
TECHNICAL
5. TECHNICAL INFORMATION
Product Maintenance
To maintain optimum performance and minimize wear, clean this product frequently. Usage and
environment are contributing factors in determining the cleaning frequency.
Clean this product at least twice a month. Dust build-up reduces light output performance and can cause
overheating. This can lead to reduced light source life and increased mechanical wear.
To clean the product:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external
vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl
alcohol.
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.

Page 18 of 22
TECHNICAL SPECIFICATIONS
Ovation H-265WW User Manual Rev. 1
6. TECHNICAL SPECIFICATIONS
Dimensions and Weight
Note: Dimensions in inches rounded to the nearest hundredth.
Power
Light Source
Photometrics
Thermal
DMX
Ordering
Length Width Height Weight
13.11 in (333 mm) 9.41 in (240 mm) 13.34 in (339 mm) 17.8 lb (8.1 kg)
Power Supply Type Range Voltage Selection
Switching (internal) 100 to 240 VAC, 50/60 Hz Auto-ranging
Parameter 120 V, 60 Hz 208 V, 60Hz 230 V, 50 Hz
Consumption 147 W 147 W 149 W
Operating Current 1.21 A .694 A 0.641 A
Fuse T 3.15 A, 250 V T 3.15 A, 250 V T 3.15 A, 250 V
Power I/O U.S./Canada Worldwide
Power input connector Hard-wired Hard-wired
Power Cord plug Bare-wired Bare-wired
Type Power Lifespan
LED 230 W 50,000 hours
Color Quantity Current
WW 1 2.3 A
Parameter No Lens 45° Lens 25° Lens
Beam Angle 50° 39° 19°
Field Angle 79° 69° 36°
Illuminance @ 5 m 400 lux 623 lux 1,933 lux
Maximum External Temperature Cooling System
113 °F (45 °C) Convection
I/O Connector Channel Range
5-pin XLR, Phoenix connector 1, 2, or 5
Product Name Item Code UPC Number
OVATIONH265WW 03031466 781462218140
UL 1573
CSA C22.2 No. 166
E113093
R