Chauvet Well Quad-M User manual

User Manual

Edition Notes
WELL™ Quad-M User Manual
Edition Notes
This user manual covers the description, safety precautions, installation, programming,
operation, and maintenance of the WELL™ Quad-M.
CHAUVET® released this edition of the WELL™ Quad-M user manual in May 2014.
Trademarks
CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or
Chauvet). The CHAUVET® logo in its entirety including the CHAUVET® name and the
dotted triangle, and all other trademarks in this manual pertaining to services, products,
or marketing statements (example: It’s Green Thinking™) are owned or licensed by
CHAUVET®. Any other product names, logos, brands, company names, and other
trademarks featured or referred to within this document are the property of their
respective trademark holders.
Copyright Notice
CHAUVET® owns the content of this user manual in its entirety, including but not limited
to pictures, logos, trademarks, and resources.
© Copyright 2014 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Manual Use
CHAUVET® authorizes its customers to download and print this manual for professional
information purposes only. CHAUVET® expressly prohibits the usage, copy, storage,
distribution, modification, or printing of this manual or its content for any other purpose
without written consent from CHAUVET®.
Document Printing
For better results, print this document in color, on letter size paper (8.5 x 11 in), double-
sided. If using A4 paper (210 x 297 mm), configure your printer to scale the content
accordingly.
Intended Audience
Any person in charge of installing, operating, and/or maintaining this product should
completely read through the guide that shipped with the product, as well as this manual,
before installing, operating, or maintaining this product.
Disclaimer
CHAUVET® believes that the information contained in this manual is accurate in all
respects. However, CHAUVET® assumes no responsibility for any errors or omissions
in this document. CHAUVET® reserves the right to revise and make changes to the
content of this document without obligation that CHAUVET® notify any person or
company of such revision or changes. This does not in any way constitute a
commitment by CHAUVET® to make such changes. CHAUVET® may issue a revision
of this manual or a new edition to incorporate such changes.
Author Date Editor Date
D. Couppe
5/6/14
A. Leon
5/6/14

Table of Contents
WELL™ Quad-M User Manual -i-
Table of Contents
1. Before You Begin......................................................................................................................................1
What Is Included...........................................................................................................................................................1
Claims..........................................................................................................................................................................................1
Manual Conventions ....................................................................................................................................................................1
Symbols.......................................................................................................................................................................................1
Safety Notes .................................................................................................................................................................2
Personal Safety............................................................................................................................................................................2
Mounting and Rigging..................................................................................................................................................................2
Power and Wiring.........................................................................................................................................................................2
Operation.....................................................................................................................................................................................2
Expected LED Lifespan................................................................................................................................................2
2. Introduction...............................................................................................................................................3
Description....................................................................................................................................................................3
Features........................................................................................................................................................................3
Overview.......................................................................................................................................................................4
Overview.......................................................................................................................................................................5
Dimensions...................................................................................................................................................................6
3. Setup..........................................................................................................................................................7
AC Power......................................................................................................................................................................7
AC Plug........................................................................................................................................................................................7
Fuse Replacement.......................................................................................................................................................................7
Battery Charge Notes...................................................................................................................................................................8
Storage Notes..............................................................................................................................................................................8
Turn Product On ...........................................................................................................................................................8
Turn Product Off ...........................................................................................................................................................8
DMX Linking..................................................................................................................................................................9
DMX Modes .................................................................................................................................................................................9
Master/Slave Connectivity............................................................................................................................................................9
W-DMX™ Operation...................................................................................................................................................10
Initial Setup................................................................................................................................................................................10
Configuration..............................................................................................................................................................................10
Product Pairing...........................................................................................................................................................................10
Lens Angle Adjustment...............................................................................................................................................11
Positioning ..................................................................................................................................................................11
4. Operation.................................................................................................................................................13
Control Panel Description...........................................................................................................................................13
Control Options...........................................................................................................................................................13
Programming ..............................................................................................................................................................13
DMX Personality ........................................................................................................................................................................13
DMX Control...............................................................................................................................................................................13
Loss of Signal Setting ................................................................................................................................................................14
Static Color ................................................................................................................................................................................14
Auto Programs...........................................................................................................................................................................14
Edit Custom Programs..............................................................................................................................................................14
Strobe Personality......................................................................................................................................................................14
Battery Life.................................................................................................................................................................................14
Master/Slave..............................................................................................................................................................................15
Color Settings.............................................................................................................................................................................15
Effect Key Programming............................................................................................................................................................15
Color Key Programming.............................................................................................................................................................15
Dimmer Curves..........................................................................................................................................................................16
Control Panel Lock.....................................................................................................................................................................16
Password...................................................................................................................................................................................16

Table of Contents
-ii- WELL™ Quad-M User Manual
Settings Lock Out.......................................................................................................................................................................16
Program Upload.........................................................................................................................................................................17
Resetting Factory Defaults.........................................................................................................................................................17
Resetting Calibration Defaults....................................................................................................................................................17
Setting the..................................................................................................................................................................................17
White Color................................................................................................................................................................................17
Calibrating the............................................................................................................................................................................18
White Color................................................................................................................................................................................18
TOUR Notes ...............................................................................................................................................................18
Master Dimmer...........................................................................................................................................................................18
Red, Green, Blue, and Amber Color Selection...........................................................................................................................18
Color Macros..............................................................................................................................................................................18
Strobe ........................................................................................................................................................................................18
Auto/Custom..............................................................................................................................................................................18
Dimmer Speed...........................................................................................................................................................................18
Menu Map...................................................................................................................................................................19
DMX Values................................................................................................................................................................21
5. Technical Information.............................................................................................................................27
Product Maintenance..................................................................................................................................................27
Returns .......................................................................................................................................................................27
Technical Specifications .............................................................................................................................................28
Contact Us....................................................................................................................Error! Bookmark not defined.

Before You Begin
WELL™ Quad-M User Manual -1-
1. Before You Begin
What Is Included
Single Product:
•WELL™ Quad-M
•Battery charger
•Warranty card
•Quick Reference Guide
Six-piece Set:
•Six WELL™ Quad-M products
•Six-bay flight case with built-in battery
charger
•Warranty card
•Quick Reference Guide
Claims
Carefully unpack the product immediately and check the box to make sure all the parts
are in the package and are in good condition.
If the box or the contents (the product and included accessories) appear damaged from
shipping or show signs of mishandling, notify the carrier immediately,
not CHAUVET®.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of delivery.
Manual Conventions
Convention Meaning
1~512
A range of values in the text
50/60
A set of mutually exclusive values in the text
<SET>
A button on the product’s control panel
Settings
A product function or a menu option
MENU>Settings
A sequence of menu options
1~10
A range of menu values from which to choose in a menu
Yes/No
A set of two mutually exclusive menu options in a menu
ON
A unique value to be entered or selected in a menu
Symbols
Symbols Meaning
Critical installation, configuration, or operation information.
Failure to comply with this information may cause the product not
to work, damage third-party equipment, or cause harm to the
operator.
Important installation or configuration information. Failure to
comply with this information may keep the product from working.
Useful information.
The term “DMX” used throughout this manual refers to the USITT DMX512-A
digital data transmission protocol.

Before You Begin
-2- WELL™ Quad-M User Manual
Safety Notes
Read all the following Safety Notes before working with this product. These notes
include important information about the installation, usage, and maintenance of this
product.
This product contains no user-serviceable parts. Any reference to servicing in
this user manual will only apply to properly trained CHAUVET® certified
technicians. Do not open the housing or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this
product.
Personal Safety
•Avoid direct eye exposure to the light source while the product is on.
•Always disconnect this product from its battery charger and turn the battery switch
off before servicing.
•Always connect this product’s battery charger to a grounded circuit to avoid the risk
of electrocution.
•Do not touch this product’s housing when operating because it may be hot.
Mounting and
Rigging •Do not submerge this product or subject it to water jets (IP44). Regular outdoor
operation under light rain or splashing water is fine.
•Do not hang this product, as this is a floor-standing product.
•Always carry this product using the built-in handle.
•Do not leave any flammable material within 50 cm of this product while operating or
recharging the battery.
Power and Wiring
•Always make sure that you are connecting this product’s battery charger to the
proper voltage, as per the specifications in this manual or on the product’s sticker.
•Never connect this product’s battery charger to a dimmer pack or rheostat.
•Never disconnect this product’s battery charger by pulling or tugging on the power
cable.
Operation
•Do not operate this product if you see damage on the housing, lenses, or cables. In
any of these cases, have the damaged parts replaced by an authorized technician
at once.
•Do not cover the ventilation slots when the product is operating to avoid internal
overheating.
•The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate this
product at a higher temperature.
•Do not close the flight case/charger lid when during charging.
•In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your CHAUVET® product may require service, contact
CHAUVET® Technical Support.
Expected LED
Lifespan LEDs gradually decline in brightness over time, mostly because of heat. Packaged in
clusters, LEDs exhibit higher operating temperatures than in ideal, single-LED
conditions. For this reason, using clustered LEDs at their fullest intensity significantly
reduces the LEDs’ lifespan. Under normal conditions, this lifespan can be 40,000 to
50,000 hours. If extending this lifespan is vital, lower the operating temperature by
improving the ventilation around the product and reducing the ambient temperature to
an optimal operating range. In addition, limiting the overall projection intensity may also
help to extend the LEDs’ lifespan.

Introduction
WELL™ Quad-M User Manual -3-
2. Introduction
Description
The WELL™ Quad-M (Wireless Event Light Luminaire) is a battery powered, portable
upward wash light. It consists of a single product that contains the lithium ion battery,
the
LEDs, the LED drivers, and the main control. The battery provides up to 10 hours of
runtime.
When purchased as a single product, it comes with a stand-alone single product battery
charger. Additional batteries are available for purchase.
When purchased as a 6-piece set, they come with an empty flight case that has six
storage bays and a built-in charger. Each storage bay in the flight case has its own
battery charging connector. This allows recharging all six WELL™ Quad-M products
simultaneously while in the flight case. The W-DMX™ (Wireless DMX) transmitter is
available for purchase separately.
Features
•DMX Channels: 3, 4, 5, 6, 10, or 15
•16-bit dimming of individual colors as well as master dimmer
•Lithium ion battery
•IR remote controllable (remote included)
•10 hour battery life at full output
•10 hour charge time from 0 to 100%
•Reflective mirror finish, blends with surroundings
•Easy to use charger included

Introduction
-4- WELL™ Quad-M User Manual
Overview
W-DMX™
Antenna
Back View
Bottom View
Power
Switch
DMX In/Out
Battery Charging
Port
Foot
Release
Handle
Control
Panel
Adjustable
Foot
Battery Storage
Power Switch

Introduction
WELL™ Quad-M User Manual -5-
Overview
•To access the static colors on the remote, press and hold the static play button
for 3–5 seconds before pressing the button for the desired color.
•The intensity control buttons only work in static color mode.
•NOTE: Intensity Control button response may be gradual.
Blue +/
-Green +/
-
Static Play
Red +/
-
Effect Key
Control
Speed
Control
On/Off
Amber
+/-
Color Key
Control
Intensity
Control

Introduction
-6- WELL™ Quad-M User Manual
Dimensions

Setup
WELL™ Quad-M User Manual -7-
3. Setup
AC Power
Each WELL™ Quad-M has an auto-ranging battery charger, whether stand-alone or
inside the flight case that works with an input voltage range of 100 to 240 VAC,
50/60 Hz. To determine the power requirements for each WELL™ Quad-M, refer to the
label affixed to the product. For more information, see the Technical Specifications
section.
The listed current rating indicates the maximum current draw during normal operation.
For more information, you may download Sizing Circuit Breakers
from the CHAUVET®
website: www.chauvetpro.com.
Always connect this product’s battery charger to a protected circuit with an
appropriate electrical ground to avoid the risk of electrocution or fire.
Never connect this product’s battery charger to a rheostat (variable resistor) or
dimmer circuit, even if the rheostat or dimmer channel serves only as a 0 to 100%
switch.
AC Plug
The WELL™ Quad-Ms battery charger comes with a power input cord terminated with
an Edison plug (US market). If the power input cord that came with your product has no
plug or you need to change the Edison plug, use the table below to wire the new plug.
Connection Wire (U.S.) Wire (Europe) Screw Color
AC Live
Black
Brown
Yellow or Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green
Make sure to disconnect the product’s power cord before replacing a blown fuse.
Always replace the blown fuse with another of the same type and rating.
Fuse Replacement
The standalone battery charger has no external fuse. However, the
flight case/charger comes with a replaceable fuse
(T 6.3 A @ 250 V).
To change the fuse on the flight case/charger, do the following:
1. Disconnect the product from the power outlet.
2. With a Phillips #2 head screwdriver, unscrew the fuse holder
cap from its housing.
3. Remove the blown fuse and replace it with a good fuse of the
same type and rating (T 6.3 A @ 250 V).
4. Screw the fuse holder cap back in its place and reconnect
power.

Setup
-8- WELL™ Quad-M User Manual
Battery Charge Notes
•Make sure to turn the battery storage switch on before connecting the product to the
charger.
•Always use the supplied charger to recharge the built-in battery.
•Recharge the battery within three days of last use.
•Recharge the battery to full capacity before storing this product.
•For best results, charge the battery in a temperature between 32 ºF (0 ºC), and
95 ºF (35 ºC).
•When charging the battery, keep the product at no less than 1 m from any open flame
or hot plate.
•When charging the battery inside the flight case/charger, keep the flight case’s cover
open.
•Always charge the battery with the product in an upright position.
•Do not keep charging the battery for more than 24 hours.
•Perform a full discharge/recharge cycle every three months.
•During charging, the green power indicator LED will illuminate solid, regardless of the
level of charge of the battery.
•Once fully charged, while still connected to the battery charger, the green power
indicator LED will turn off.
Storage Notes
•Always store the unit in an upright position (≤ 10º tilt).
•Recharge the battery to full capacity before storing the unit.
•Store charged unit(s) in a dry environment, away from direct sunlight.
•Turn the battery storage switch off if storing the unit for more than seven days.
Turn Product On
1. Turn the battery storage switch on.
2. Push the On/Off switch on the top for more than three seconds (the built-in red LED
will illuminate solid).
When not connected to the battery charger, the power status LED indicates the
amount of remaining battery charge, as follows:
Green: >70% (100 to 70% charge)
Yellow: >20% (69 to 21% charge)
Red: Empty (20% to 0 charge)
Turn Product Off
1. Push the On/Off switch on the top for more than three seconds.
2. If storing the product for more than seven days after recharging it, also turn the
battery storage switch off.

Setup
WELL™ Quad-M User Manual -9-
DMX Linking
You can link the WELL™ Quad-M to a DMX controller using a standard DMX serial
connection or via W-DMX™. If using other DMX compatible products with the
WELL™ Quad-M, you can control each individually with a single DMX controller.
DMX Modes
The WELL™ Quad-M uses the standard DMX data connection for its TOUR, TR16,
ARC.1, AR1.D, ARC.2, AR2.D, AR2.S and HSV DMX modes.
•Refer to the Introduction section for a brief description of these modes.
•Refer to the Operation section to learn how to configure the WELL™ Quad-M to work
in these modes.
•The DMX Values section provides you with detailed information regarding the DMX
modes.
Master/Slave
Connectivity
The Master/Slave mode allows a WELL™ Quad-M (master product) to control one or
more products (slave products) without a DMX controller.
One WELL™ Quad-M becomes the master product either when running
in static (STAT)
mode or when using the automatic (AT) or customizable (PR) programs.
In addition, you must configure each of the slave products (via control panel) to operate
in Slave (SLAV) mode. During Master/Slave operation, the slave products will operate in
unison with the master product.
For more information, see the Menu Map section.
Do not connect a DMX controller to products operating in Master/Slave mode. The
DMX controller signals may interfere with the signals from the master product.
•The Operation section of this manual provides detailed instructions on how to
configure the Master and Slave products.
•If you need more information about DMX standards, Master/Slave connectivity,
or the DMX cables needed in order to link the product to a DMX controller, you
can download the DMX Primer from the CHAUVET® website:
www.chauvetpro.com.
•Verify the DIMX and CURV settings are set to OFF for optimal control of the
TR16 personality. For more information, see the Menu Map section.

Setup
-10- WELL™ Quad-M User Manual
W-DMX™ Operation
The product can operate in W-DMX™ mode up to 300 m (900 ft) from the
W-DMX™ transmitter. For wireless operation, the W-DMX™ receiver inside the product
must be paired with a W-DMX™ transmitter.
Initial Setup
1. Turn the W-DMX™ transmitter on.
2. Connect the W-DMX™ transmitter to a DMX controller.
3. Place the product within 300 m from the W-DMX™ transmitter.
4. Disconnect any DMX cable from the product.
5. Turn the product on.
Configuration
1. From the product’s control panel, go to RUN > DMX.
2. Select the desired DMX start address. .
3. Go to WDMX > ACTI.
4. Select ON.
Product Pairing
Product currently paired with the transmitter
•If the product is paired with the W-DMX™ transmitter, a red LED on the On/Off
switch will slowly flash. The product is ready to work in wireless mode.
Pairing the product with a new W-DMX™ transmitter
1. From the product’s control panel, go to WDMX > REST.
2. Select YES (a red LED appears on the On/Off switch).
3. From the W-DMX™ transmitter, press <RESET> (the SIGNAL indicator will flash).
4. Once the transmitter has found the product, the SIGNAL indicator on the W-DMX™
transmitter will illuminate solid.
5. From the On/Off switch, the red LED flashes slowly indicating the presence of DMX
signal.
W-DMX™ operation can be interrupted or inhibited by liquid masses between the
transmitter and receiver such as water, snow, or people. For best results, keep
the antenna clear of any liquid mass.
WDMX™ Setup
Control Panel
WDMX Transmitter

Setup
WELL™ Quad-M User Manual -11-
Lens Angle
Adjustment
The product contains a single LED lens platform, that which allows the unit to be tilted
from 55º up to 105º from the center.
Positioning
The WELL™ Quad-M stands on the support legs and positioned on a hard, steady
surface that can support its weight. You should not mount the product in any way.
•When selecting an installation location, consider easy access to this product for
operation, programming adjustments, and routine maintenance.
•Make sure to place the product away from any flammable material.
•Do not mount the product in places where heavy rain, water jets, extreme
temperature changes, or restricted ventilation may affect it.
•This is a floor-standing fixture. Do not hang this unit.
•Do not operate the unit in a sealed enclosure or in an area without air circulation.

Setup
-12- WELL™ Quad-M User Manual
Tilt Angle Procedure
The WELL™ Quad-M stands on a hard, steady surface that can support its weight.
Using the installed retractable foot, the product is adjustable by using the foot release
lever up to10º.
Mounting Diagram
Correct Floor
Mounting

Operation
WELL™ Quad-M User Manual -13-
4. Operation
Control Panel
Description
Button Function
<MENU>
Exits from the current menu or function
<ENTER>
Enables the currently displayed menu or sets the currently
selected value in to the current function
<UP>
Navigates upward through the menu options or increases the
numeric value when in a function
<DOWN>
Navigates downward through the menu options or decreases the
numeric value when in a function
Control Options
You can set the WELL™ Quad-M starting address in the 001 to 512 DMX range. This
enables control of up to 34 products in the 15-channel TR16 personality.
Programming
The menu map shows the main level and a variable number of programming levels for
each option. For more information on how to use the menu options, refer to the Menu
Map section.
•To go to the desired main level, press <MENU> repeatedly until the desired option
displays on the control panel. Press <ENTER> to select. This will take you to the first
programming level for that option.
•To select an option or value within the current programming level, press UP or
<DOWN> until the option shows on the display. Press <ENTER> to select. In this
case, if there is another programming level, you will see that first option, or you will
see the selected value.
•Press <MENU> repeatedly to exit to the previous main level.
DMX Personality
This setting allows you to choose a particular DMX personality.
1. Go to the PERS main level.
2. Select the desired personality (
TOUR, TR16, ARC.1, AR1.D, ARC.2, AR2.D, AR2.S
or
HSV
).
For the highest starting address you can select for each personality, see the DMX
Values section. Verify that the starting addresses on the products do not overlap
due to the new personality setting.
DMX Control
In this mode, each product will respond to a unique starting address from the DMX
controller. All products with the same starting address will respond in unison.
1. Select a DMX personality as shown in DMX Personality.
2. Set the running mode:
a. Go to the RUN main level.
b. Select the DMX programming level.
3. Set the starting address:
a. Go to ADDR main level.
b. Select the starting address (D.001~512).
The highest recommended starting address for each DMX mode are as follows:
DMX Mode DMX Address DMX Mode DMX Address DMX Mode DMX Address
TOUR
503
ARC.2
509
HSV
510
ARC.1
510
AR2.D
508
TR16
498
AR1.D
509
AR2.S
507

Operation
-14- WELL™ Quad-M User Manual
Loss of Signal Setting
This setting controls how the product will respond when the DMX signal is lost.
1. Go to the SET main level, and select DERR.
a. Select SAVE to make the product use the last command used when the signal
is lost.
b. Select
BLAK
to turn off the all the LEDs when the signal is lost.
Static Color
The Static Color mode allows for permanent RGBA color mixing without a DMX
controller.
1. Go to the STAT main level.
2. Select the desired color (RED, GREN, BLUE, or AMBR).
3. Select the desired color value (000~255).
4. Repeat the steps for additional colors.
5. Select STRB.
6. Select the desired frequency (
00
~
20
).
Auto Programs
Auto programs allow for dynamic RGBA color mixing without a DMX controller.
1. Go to AUTO.
2. Select the desired auto (AT. 01~10)or custom program (PR. 01~10).
3. Select the desired speed at which the chosen program will run (
P. 000~255
).
You cannot edit any of the auto programs (AUTO 01~10).
Edit Custom
Programs
This setting allows the programming of up to 30 scenes for each of the 10 customizable
programs, including colors and effects.
1. Go to the EDIT main level.
2. Select the desired auto program (PR. 01~10).
3. Select the desired scene (SC. 01~30).
4. Select the desired color or effect (RED, GREN, BLUE, AMBR, STRB, TIME, or
FADE).
5. Select the color or effect value (000~255 for colors and timers, or 00~20 for strobe).
6. Repeat the steps for additional colors or effects.
7. Return to the scene level (SC. 01~30).
8. Repeat the settings of colors and effects for the other scenes.
Strobe Personality
This setting allows you to select the CLASSIC (01~20 Hz) strobe or SPECIAL
(Random/Slow/Fast) strobe personalities.
1. Go to the SET main level.
2. Select a strobe personality (SPEC or CLAS).
Battery Life
This setting allows the user to select the output intensity for a given runtime (battery life).
1. Go to SET.
2. Select LIFE.
3. Select a battery life (ECON or LONG).

Operation
WELL™ Quad-M User Manual -15-
Master/Slave
The Master/Slave mode allows a group of WELL™ Quad-Ms (slave products) to
simultaneously duplicate the output of another WELL™ Quad-M (master product)
without a DMX controller.
1. Set each of the slave products:
a. Go to RUN.
b. Select SLAVE.
2. Set the master product:
a. Set the running mode to DMX (see DMX Control).
b. Select an auto or custom program as explained in Auto Programs above, or a
static mix of colors.
•The master product is the one that runs a program whether in Auto, Custom or
Static Color mode.
•Do not connect a DMX controller to the products configured for Master/Slave
operation. The DMX controller may interfere with signals from the master
product.
•The master product should be the first product in the daisy chain.
Color Settings
The Color setting determines how the product generates the white color based on
various RGB settings.
1. Go to the SET main level.
2. Select COLR.
3. Select
OFF
,
RGBW
, or
UC
.
OFF:
When all the RGB faders are set to 255, the output is maximum, although
the resulting white color may not be balanced.
RGBW:
When all the RGB faders are set to 255, the resulting output is defined by
the configured White color (see White Calibration).
UC:
When all the RGB faders are set to 255, the output matches that of less
efficient products (Universal Color).
Effect Key
Programming
This setting allows you to program the effect keys on the IRC remote.
1. Go to EDIT > EKY level.
2. Select the desired key on the IRC remote to program (EKY 1~6).
3. Enter the desired program (AT. 01~10 or PR. 01~10).
4. Repeat the steps to program additional effect keys.
5. Press the corresponding effect key to confirm programming.
Color Key
Programming
This setting allows you to program the color keys on the IRC remote.
1. Go to EDIT > CKY level.
2. Select the desired key to program (CKY 1~6).
3. Select the desired color or effect (RED, GREEN, BLUE, or STROBE).
4. Select the desired value (000~255 for colors or 00~20 for strobe).
5. Repeat the steps to program additional color keys.
6. Press the corresponding color key to confirm programming.

Operation
-16- WELL™ Quad-M User Manual
Dimmer Curves
This setting provides you with four options to simulate the dimming curve of an
incandescent light product.
1. Go to the SETmain level.
2. Select DIMX.
3. Select the desired dimmer curve (
OFF
,
DIM1
,
DIM2
,
DIM3
, or
DIM4
).
OFF
The output is proportional (linear) to the dimmer and RGBA channel
values.
DIM1~4:
The output follows the dimmer and RGBA channel values based on the
corresponding dimmer curve, being DIM1 the fastest and DIM4 the
slowest.
Dimmer Curve
Settings
This setting allows you to select the dimmer curve shape using the red, green, blue,
amber, and dimmer faders.
1. Go to the SET main level.
2. Select CURV.
3. Select the desired dimmer curve (OFF, CV1, CV2, or CV3).
OFF
This output is proportional (linear) to the Dimmer and RGBA channel
values.
CV1~3
This output follows the dimmer and RGBA channel values based on the
corresponding dimmer curve, being CV1 the fastest and CV3the slowest.
For optimum control of the 16-bit dimming channels in the TR16 personality, be
sure that both dimming curves in SET > DIMX and SET > CURV are set to OFF
Control Panel Lock
This setting enables you to activate or disable the control panel lock, which keeps non-
authorized personnel from changing the product’s settings.
1. Go to the KEY main level.
2. Select
ON
or
OFF
.
When the control panel lock is active, the product will prompt you to enter the
password after 30 seconds of control panel inactivity or after turning on the
product.
Password
If you are prompted to enter a password on the product, press the buttons in the
following order: UP > DOWN > UP > DOWN > ENTER.
The product’s password cannot
be changed and must be entered whenever you are prompted.
Settings Lock Out
This setting enables you to activate or disable the main level SET (settings) lock, which
keeps unauthorized personnel from changing the product’s settings.
1. Go to the SET main level.
2. Select SLCK.
3. Select ON or OFF.