Chauvet Net-X User manual

User Manual

Edition Notes
This User Manual includes a description of, and safety precautions, setup, installation,
operation, and maintenance for the CHAUVET® Net-X™. This edition was published in
November 2014.
Trademarks
CHAUVET® is a registered trademark of Chauvet & Sons Inc. (d/b/a CHAUVET® or
Chauvet). The CHAUVET® logo in its entirety including the Chauvet name and the dotted
triangle, and all other trademarks on this manual pertaining to services, products, or
marketing statements (example: It’s Green Thinking™) are owned or licensed by
CHAUVET®. Any other product names, logos, brands, company names, and other
trademarks featured or referred to within this document are the property of their respective
trademark holders.
Copyright Notice
Chauvet owns the content of this user manual in its entirety, including but not limited to
pictures, logos, trademarks, and resources.
Art-Net™ is designed and copyrighted by Artistic Licence Holdings Ltd.
© Copyright 2014 Chauvet. All rights reserved.
Printed in P.R.C. Electronically published by Chauvet in the United States of America.
Manual Use
Chauvet authorizes its customers to download and print this manual for professional
information purposes only. Chauvet expressly prohibits the usage, copy, storage, distribution,
modification, or printing of this manual or its content for any other purpose without its written
consent.
Document Printing
For best results, print this document in color, on letter size paper (8.5 x 11 inches), double
sided. If using A4 paper (210 x 297 mm), configure your printer to scale the content
accordingly.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects.
However, Chauvet assumes no responsibility for any error or omissions in this document.
Chauvet reserves the right to revise this document and to make changes from time to time in
the content hereof without obligation of Chauvet to notify any person or company of such
revision or changes. This does not constitute in any way a commitment by Chauvet to make
such changes. Chauvet may issue a revision of this manual or a new edition of it to
incorporate such changes.
Document Revision
The Net-X™ User Manual, Rev. 2 supersedes all previous versions of this manual. Please
discard any older versions of this manual you may have, whether in printed or electronic
format, and replace them with this version. Go to www.chauvetprofessional.com for the latest
version.
Author
Date
Editor
Date
A. Leon
11/12/14
M. Trouard
11/13/14

Table Of Contents
Before You Begin ................................................................................................................ 61.
What Is Included ........................................................................................................................................ 6
Unpacking .................................................................................................................................................. 6
Claims .................................................................................................................................................... 6
Conventions ............................................................................................................................................... 6
Symbols ..................................................................................................................................................... 6
Safety Notes .............................................................................................................................................. 7
Introduction ......................................................................................................................... 82.
Product Description................................................................................................................................ 8
Product Features ................................................................................................................................... 8
Additional Products ................................................................................................................................ 8
Product Overview ...................................................................................................................................... 8
Product Dimensions .................................................................................................................................. 9
Setup And Installation ........................................................................................................103.
AC Power ................................................................................................................................................ 10
Fuse Replacement .................................................................................................................................. 10
Fuse Replacement Diagram ................................................................................................................ 10
Mounting .................................................................................................................................................. 11
Signal Connection ................................................................................................................................... 11
Signal Connection Diagram ................................................................................................................. 11
Installation Guidelines ............................................................................................................................. 11
Configuration And Operation ............................................................................................124.
Control Panel ........................................................................................................................................... 12
Menu Map ................................................................................................................................................ 13
Using The Menu ...................................................................................................................................... 13
Configuring Net Address ...................................................................................................................... 13
Configuring Subnet Address ................................................................................................................ 13
Configuring Universes ......................................................................................................................... 14
Configuring DMX Outputs .................................................................................................................... 14
Configuring IP Addresses .................................................................................................................... 14
Configuration Examples .......................................................................................................................... 15
DMX Source (DMX Splitter) ................................................................................................................. 15
Art-Net™ Source (Art-Net™ adapter) .................................................................................................. 16
Art-Net™ And DMX Sources ............................................................................................................... 17
Indicators ................................................................................................................................................. 17
Technical Information ........................................................................................................185.
Maintenance ............................................................................................................................................ 18
Technical Specifications ....................................................................................................196.
Dimensions And Weight .......................................................................................................................... 19
Power....................................................................................................................................................... 19
Data Connections .................................................................................................................................... 19
Ordering ................................................................................................................................................... 19
Returns ....................................................................................................................................20
Contact Us ...............................................................................................................................21

Antes de Empezar ..............................................................................................................231.
Qué va Incluido ........................................................................................................................................ 23
Desembalaje ............................................................................................................................................ 23
Reclamaciones .................................................................................................................................... 23
Convenciones .......................................................................................................................................... 23
Símbolos .................................................................................................................................................. 23
Notas de Seguridad ................................................................................................................................. 24
Introducción .......................................................................................................................252.
Descripción del Producto ..................................................................................................................... 25
Características del Producto ................................................................................................................ 25
Productos Adicionales ......................................................................................................................... 25
Visión General del Producto .................................................................................................................... 25
Dimensiones del Producto ...................................................................................................................... 26
Montaje e Instalación .........................................................................................................273.
Corriente Alterna ..................................................................................................................................... 27
Sustitución del Fusible............................................................................................................................. 27
Diagrama de Sustitución del Fusible ................................................................................................... 27
Instalación ............................................................................................................................................... 28
Conexión de Señal .................................................................................................................................. 28
Diagrama de Conexión de Señal ......................................................................................................... 28
Pauta de Instalación ................................................................................................................................ 28
Configuración y Funcionamiento ......................................................................................294.
Panel de Control ...................................................................................................................................... 29
Mapa de Menú ......................................................................................................................................... 30
Utilizar el Menú ........................................................................................................................................ 31
Configurar la Dirección de Red ............................................................................................................ 31
Configurara la Dirección de Subred..................................................................................................... 31
Configurar Universos ........................................................................................................................... 32
Configurar las Salidas DMX ................................................................................................................. 32
Configurar la Dirección IP .................................................................................................................... 32
Ejemplos de Configuración ..................................................................................................................... 33
Fuente DMX (Splitter DMX) ................................................................................................................. 33
Fuente Art-Net™ (Adaptador Art-Net™).............................................................................................. 34
Fuentes Art-Net™ y Fuentes DMX ...................................................................................................... 35
Indicadores .............................................................................................................................................. 36
Información Técnica ...........................................................................................................375.
Mantenimiento ......................................................................................................................................... 37
Especificaciones Técnicas ................................................................................................386.
Dimensiones y Peso ................................................................................................................................ 38
Alimentación ............................................................................................................................................ 38
Conexiones de Datos .............................................................................................................................. 38
Pedidos .................................................................................................................................................... 38
Devoluciones...........................................................................................................................39
Contacto ..................................................................................................................................40

Avant de Commencer .........................................................................................................421.
Contenu ................................................................................................................................................... 42
Déballage ................................................................................................................................................ 42
Réclamations ....................................................................................................................................... 42
Conventions ............................................................................................................................................. 42
Symboles ................................................................................................................................................. 42
Consignes de Sécurité ............................................................................................................................ 43
Introduction ........................................................................................................................442.
Description de l'Appareil ...................................................................................................................... 44
Caractéristiques de l'Appareil .............................................................................................................. 44
Appareils Supplémentaires .................................................................................................................. 44
Vue d'Ensemble du Produit ..................................................................................................................... 45
Dimensions de l'Appareil ......................................................................................................................... 46
Configuration et Installation ..............................................................................................473.
Alimentation CA ....................................................................................................................................... 47
Remplacement des Fusibles ................................................................................................................... 47
Schéma de Remplacement du Fusible ................................................................................................ 47
Montage ................................................................................................................................................... 48
Connections du Signal............................................................................................................................. 48
Schéma des Connections de Signal .................................................................................................... 48
Instructions pour l'Installation .................................................................................................................. 48
Configuration et Utilisation ................................................................................................494.
Panneau de Commande.......................................................................................................................... 49
Plan du Menu .......................................................................................................................................... 50
Utilisation du Menu .................................................................................................................................. 51
Configuration de l'Adresse Réseau ..................................................................................................... 51
Configuration de l'Adresse de Sous-réseau ........................................................................................ 51
Configuration des Univers ................................................................................................................... 52
Configuration des Sorties DMX ........................................................................................................... 52
Configuration des Adresse IP .............................................................................................................. 52
Exemples de Configuration ..................................................................................................................... 53
Source DMX (répartiteur DMX) ............................................................................................................ 53
Source Art-Net™ (Adaptateur Art-Net™) ............................................................................................ 54
Sources Art-Net™ et DMX ................................................................................................................... 56
Indicateurs ............................................................................................................................................... 56
Informations Techniques ...................................................................................................575.
Entretien .................................................................................................................................................. 57
Spécificités Techniques .....................................................................................................586.
Dimensions et Poids ................................................................................................................................ 58
Alimentation ............................................................................................................................................. 58
Connections de Données ........................................................................................................................ 58
Commande .............................................................................................................................................. 58
Renvois ....................................................................................................................................59
Nous Contacter .......................................................................................................................60

Before You Begin
Page 6 of 6Net-X™ User Manual Rev. 2
Before You Begin 1.
What Is Included
• Net-X™
• IEC power cord
• Warranty card
• User Manual
Unpacking
Carefully unpack the Net-X™ and check that all the parts are in the package, and are in good
condition.
Claims
Upon receipt, if the container or the contents (the product and included accessories) appear
damaged from shipping, or show signs of mishandling, notify the carrier immediately, not
Chauvet. Failure to do so in a timely manner may invalidate your claim with the carrier. In
addition, keep the container and all the packing material for inspection.
For other issues such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with Chauvet within 7 days of receiving the merchandise. For
information on contacting Chauvet, see Contact Us at the end of this Manual.
Conventions
Convention
Meaning
1–512
A range of values
50/60
A set of values
Settings
A menu option
Menu > Settings
A sequence of menu options
<ENTER>
A button to be pressed
ON
A value to be entered or selected
Symbols
Symbols
Meaning
Critical installation, configuration, or operation information. Failure to comply with this
information may cause the product not to work, damage third-party equipment, or
cause harm to the operator.
Important installation or configuration information. Failure to comply with this
information may keep the product from working.
Useful information.

Before You Begin
Net-X™ User Manual Rev. 2 Page 7 of 
Safety Notes
Please read the following Safety Notes carefully before starting to work with the product.
These notes provide important safety information about the installation, usage, and
maintenance.
• Always connect this product to a grounded circuit.
• Make sure the power cord is not crimped or damaged.
• Always connect this product to a power source with the proper voltage as
listed on the product sticker.
• Do not operate the product if there is damage to the housing.
• This product is for indoor use only! It is rated IP20. Do not expose the
product to rain or moisture.
• Always disconnect this product from power before cleaning it or changing the
fuse.
• Never disconnect the product from the power source by pulling or tugging on
the cord.
• If mounting the product overhead, always secure it using a safety cable.
• Make sure there are no flammable materials close to the product when it is
operating.
• This product is not intended for permanent installation.
• Never connect the product to a dimmer or a rheostat.
• Always install the product in a location with adequate ventilation.
• Do not operate the product in an ambient temperature higher than
104 °F (40 °C).
• This product contains no user-serviceable parts. Any reference to servicing in
this User Manual will only apply to properly trained Chauvet certified
technicians. Do not open the housing or attempt any repairs.
• Any damages caused by manual modifications are not subject to warranty.
Chauvet will not accept liability for damage caused by unauthorized
modifications or not observing the safety warnings and instructions in the
manual.
• All applicable local codes and regulations apply for proper installation of this
product.
• In the event of a serious operating problem, stop using the product
immediately.
• If the product requires repair contact Chauvet. For more information see
Returns and Contact Us.
• To eliminate unnecessary wear and improve its lifespan, during periods of
non-use completely disconnect the product from power via breaker or by
unplugging it.
Keep this User Manual for future reference.

Introduction
Page 8 of  Net-X™ User Manual Rev. 2
Introduction 2.
Product Description
Net-X™ is a reliable and versatile rack-mountable Art-Net™-to-DMX adapter with an
integrated optical DMX splitter and Art-Net™ hub capability. It has two 5-pin DMX In ports
and eight 5-pin DMX Out ports, all optically isolated. It takes up to 8 Art-Net™ universes
simultaneously. The eight 5-pin DMX Out ports can be assigned to either of the DMX In ports
or to one of the Art-Net™ Neutrik® etherCON® ports. Neutrik® etherCON® ports are through
ports that allow daisy chaining of Net-X™ units.
Net-X™ provides a reliable, highly customizable network infrastructure for complex control
systems.
Product Features
• Rack mountable
• Both an Art-Net™ node and an optical splitter
• Eight optically isolated output ports
• Variable operating modes for all DMX outputs
• Two Neutrik® etherCON® in/through ports
Additional Products
The Net-X™ is an adapter and hub combined that works as part of a control system. Chauvet
has a line of video products and lighting products that work with the Net-X™. For more
information about compatible CHAUVET® products, see the Chauvet website at
http://www.chauvetlighting.com/product-manuals-literature/.
Product Overview
Power In
Fuse
Holder
DMX In
Control Panel
Buttons
Control Panel
Display
Front View
Mounting
Hole (x4)
LED Indicators
Power Switch
DMX Out
Neutrik ®
etherCON®
through ports
Back View
Rubber Foot (x4)
1
2
1
2
3
4
5
6
7
8
1
2
Power
Signal
DMX

Introduction
Net-X™ User Manual Rev. 2 Page 9 of 
Product Dimensions
1.7 in
44.4 mm
17.4 in
443 mm
6.6 in
167.9 mm
15.3 in
390 mm
19 in
483 mm
4.7 in
120 mm
0.9 in
23.5 mm

Setup And Installation
Page 10 of 0 Net-X™ User Manual Rev. 2
Setup And Installation 3.
AC Power
Net-X™ has an internal auto-ranging power supply that works with an input voltage range of
100–240 VAC, 50/60 Hz. To determine the power requirements for the Net-X™ refer to the
label affixed to the product or Technical Specifications.
The listed rating indicates the maximum current draw during normal operation. For more
information, download Sizing Circuit Breakers from the Chauvet website at
www.chauvetprofessional.com.
• Always connect this product to a properly grounded and protected
circuit.
• Never connect this product to a rheostat (variable resistor) or dimmer
circuit, even if the rheostat or dimmer channel serves only as a 0 to
100% switch.
Fuse Replacement
1. Disconnect the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the fuse holder out of the housing.
4. Remove the blown fuse from the holder.
5. Replace with a fuse of the exact same type and rating.
6. Insert the fuse holder back in place and reconnect power.
Disconnect the product from power before replacing the fuse.
Fuse Replacement Diagram
Always replace a blown fuse with another of the same type and rating.
A spare fuse is not included; however, the safety cap has room for a spare.
Installed Fuse
(held by plastic clip)
Spare Fuse Holder
(inside safety cap)
Safety Cap

Setup And Installation
Net-X™ User Manual Rev. 2 Page 11 of 
Mounting
The Net-X™ fits nicely in a standard 19” rack, or sits on a flat surface. The Net-X™ should be
placed where the menu and the ports are accessible, and where there is adequate
ventilation.
Signal Connection
The Net-X™ receives signal though 2 DMX In ports and one of 2 Neutrik® etherCON® ports.
It sends signal out through 8 DMX Out ports and the other Neutrik® etherCON® port.
Signal Connection Diagram
• The Neutrik® etherCON® ports are through ports. Each port can be either
an input or an output port.
• The DMX ports can only be input or output ports. There are 2 DMX In
ports and 8 DMX Out ports.
Installation Guidelines
The Net-X™ is used as part of a control system for operating various lighting and multi-media
products. The physical and digital construction of the control network is determined by the
location and signal needs of the products.
When designing a control system that uses the Net-X™, consider the following:
• Placing the Net-X™ so the menu and ports can be accessed
• Running the cables so there is no tension or pull on the cables or plugs
• Planning a large control system carefully before configuring the components, so IP
address, DMX address, and other identifiers are not duplicated
From DMX Sources
From Art-Net™ Sources
To Another Net-X™
Or Other Art-Net™ Products
To DMX
Controlled
Products

Configuration And Operation
Page 12 of  Net-X™ User Manual Rev. 2
Configuration And Operation 4.
The Net-X™ is configured through the control panel, using the control panel buttons. Once
the Net-X™ is properly configured it operates without user intervention.
The Net-X™ can be used as a DMX splitter only, in which case the DMX In ports must be
assigned to the DMX Out ports, but the Net, Subnet, and IP address settings do not need
configuration.
The Net-X™ can be used as an Art-Net™ hub, in which case the Art-Net™ universes must
be assigned to the DMX Out ports, and the Net, Subnet, and IP address settings must be
configured.
The Net-X™ can be used as both a DMX splitter and an Art-Net™ hub simultaneously, in
which case both the DMX assignments and the Art-Net™ settings must be configured. For
more information, see Configuration Examples.
DMX In ports and Art-Net™ universes can be assigned to multiple DMX Out
ports.
Control Panel
The control panel is the mechanism for configuring the Net-X™ settings. It has a small LCD
screen and four buttons, which are described below.
Button
Function
<MENU>
Scrolls through the first level of options, or exits from the current menu or
function
<UP>
Navigates upward through the menu list or increases the numeric value
when in a function
<DOWN>
Navigates downward through the menu list or decreases the numeric value
when in a function
<ENTER>
Enables the currently displayed menu or sets the currently selected value in
to the current function

Configuration And Operation
Net-X™ User Manual Rev. 2 Page 13 of 
Menu Map
The menu map shows the organization of the configuration settings. Use it for reference
when configuring the Net-X™.
Main Function
Programming Levels
Description
<Net>
0–127
Sets the Net address
<Subnet>
0–15
Sets the Subnet address
<Universe #1> to
<Universe #8> 0–15
Sets the Art-Net™ universe for the corresponding
DMX Out port
(only necessary if the DMX port is set to Art-Net™)
<DMX Output #1>
to
<DMX Output #8>
ArtNet Input Input source for each DMX Out port is Art-Net™
DMX #1 Input
Input source for each DMX Out port is DMX In port 1
DMX #2 Input
Input source for each DMX Out port is DMX In port 2
Without Input
DMX Out port is turned off
<IP Address #1>
x.xxx.xxx.xxx Sets the two IP addresses for the Net-X™
Note: The addresses cannot be the same.
<IP Address #2>
<Device ID>
xxxxxxxxx
Shows the Net-X™ device ID
Using The Menu
The menu is used by pressing the 4 control buttons as described in the next sections.
Configuring Net Address
The Net is the address of the network on which the Net-X™ is operating. The Net address
must be configured if the Net-X™ is being used as an Art-Net™ hub.
To configure the Net setting, do the following:
1. Press <MENU> repeatedly until <Net> shows in the display.
2. Press <ENTER>. The number in the lower right-hand corner of the display flashes.
3. Press <UP> or <DOWN> until the desired Net shows.
4. Press <ENTER>.
Configuring Subnet Address
The Subnet is the address of the subnet of the network on which the Net-X™ is operating.
The Subnet address must be configured if the Net-X™ is being used as an Art-Net™ hub.
To configure the Subnet setting, do the following:
1. Press <MENU> repeatedly until <Subnet> shows in the display.
2. Press <ENTER>. The number in the lower right-hand corner of the display flashes.
3. Press <UP> or <DOWN> until the desired Subnet shows.
4. Press <ENTER>.

Configuration And Operation
Page 14 of  Net-X™ User Manual Rev. 2
Configuring Universes
Universes are assigned to DMX Out ports when the Net-X™ is used as an Art-Net™-to-DMX
adapter. The universes are part of the process by which the Net-X™ takes the Art-Net™
protocol and converts it to DMX. There are 16 Art-Net™ universes (0–15) that can be
assigned to the DMX Out ports. Any one universe can be assigned to more than one DMX
Out port.
The menu structure presents each DMX Out port as <Universe #X>, where X is the DMX
Out port. The Art-Net™ universes are assigned by selecting a value from 0 to 16.
To assign an Art-Net™ universe to a DMX Out port, do the following:
1. Select the DMX Out port to assign an Art-Net™ universe to by pressing <MENU>
repeatedly until <Universe #X> shows in the display.
2. Press <ENTER>. The number in the lower right-hand corner of the display flashes.
3. Press <UP> or <DOWN> until the desired Art-Net™ universe shows.
4. Press <ENTER>.
Configuring DMX Outputs
The DMX Out ports must be configured to accept signal from either one of the DMX In ports,
or from the Art-Net™ source. If the DMX port is not being used it should be turned off.
The menu structure presents each DMX Out port as a <DMX Output #X>, where X is the
DMX Out port.
To configure the DMX Out ports, do the following:
1. Select the DMX Out port to configure by pressing <MENU> repeatedly until
<DMX Output #X> shows in the display.
2. Press <ENTER>. The phrase in the lower right-hand corner of the display flashes.
3. Press <UP> or <DOWN> until the desired DMX input source or state of the port shows.
4. Press <ENTER>.
Configuring IP Addresses
The IP address is the address of the Net-X™ on the network. It must be configured if the
Net-X™ is being used as an Art-Net™ hub.
To configure the IP Address, do the following:
1. Press <MENU> repeatedly until <IP Address #1> shows in the display.
2. Press <ENTER>. The left-most set of 3 digits on the display flashes.
3. Press <UP> or <DOWN> to change that set of numbers.
4. Press <ENTER>.The next set of 3 digits on the display flashes.
5. Press <UP> or <DOWN> to change that set of numbers.
6. Press <ENTER>.The right-most set of 3 digits on the display flashes.
7. Press <UP> or <DOWN> to change that set of numbers.
8. Press <MENU>.

Configuration And Operation
Net-X™ User Manual Rev. 2 Page 15 of 
Configuration Examples
Net-X™ is extremely versatile, with DMX source capabilities and Art-Net™ source
capabilities which can be combined so that the Net-X™ is acting as a DMX splitter, an
Art-Net™ adapter, and an Art-Net™ hub.
DMX Source (DMX Splitter)
DMX source-only configuration uses the Net-X™ as a DMX splitter. The DMX signal comes
in from one or both of the DMX In ports and goes out through one or more of the DMX Out
ports.
To configure the Net-X™ as a DMX splitter with the input and output assignments listed here
• DMX In port 1 goes to DMX Out ports 4 and 5
• DMX In port 2 goes to DMX Out ports 7 and 8
Do the following:
1. Disable unused DMX Out ports by doing the following for DMX Out ports 1, 2, 3, and 6:
a) Press <MENU> repeatedly until <DMX Output Port #X> shows on the display.
b) Press <ENTER>. The phrase in the lower right-hand corner of the display
flashes.
c) Press <UP> or <DOWN> until <Without Input> shows in the lower right-hand
corner.
d) Press <ENTER>. <Without Input> stops flashing.
2. Configure the DMX Out ports that will receive from DMX In port 1 by doing the following
for DMX Out ports 4 and 5:
a) Press <MENU> repeatedly until <DMX Output Port #X> shows on the display.
b) Press <ENTER>. The phrase in the lower right-hand corner of the display
flashes.
c) Press <UP> or <DOWN> until <DMX #1 Input> shows in the lower right-hand
corner.
d) Press <ENTER>. <DMX #1 Input> stops flashing.
3. Configure the DMX Out ports that will receive from DMX In port 2 by doing the following
for DMX Out ports 7 and 8:
a) Press <MENU> repeatedly until <DMX Output Port #X> shows on the display.
b) Press <ENTER>. The phrase in the lower right-hand corner of the display
flashes.
c) Press <UP> or <DOWN> until <DMX #2 Input> shows in the lower right-hand
corner.
d) Press <ENTER>. <DMX #2 Input> stops flashing.

Configuration And Operation
Page 16 of  Net-X™ User Manual Rev. 2
Art-Net™ Source (Art-Net™ adapter)
Art-Net™ source-only configuration uses the Net-X™ as an Art-Net™-to-DMX adapter. The
signal comes in from the Art-Net™ source to the Neutrik® etherCON® port and goes out
through one or more of the DMX Out ports. To configure the Net-X™ as an Art-Net™-to-DMX
adapter with the addresses and DMX Out port assignments listed here:
• Net setting of 3
• Subnet setting of 7
• IP addresses of 10.255.255.009 and 10.255.255.011
• Art-Net™ universe 4 going to DMX Out port 1
• Art-Net™ universe 8 going to DMX Out port 2
Do the following:
1. Set the Net address to 3 by doing the following:
a) Press <MENU> repeatedly until <Net> shows in the display.
b) Press <ENTER>. The number in the lower right-hand corner of the display
flashes.
c) Press <UP> or <DOWN> until 3 shows.
d) Press <ENTER>.
2. Set the Subnet address to 7 by doing the following:
a) Press <MENU> repeatedly until <Subnet> shows in the display.
b) Press <ENTER>. The number in the lower right-hand corner of the display
flashes.
c) Press <UP> or <DOWN> until 7 shows.
d) Press <ENTER>.
3. Set the IP addresses by doing the following:
a) Press <MENU> repeatedly until <IP Address #1> shows in the display.
b) Press <ENTER>. The left-most set of 3 digits on the display flashes.
c) Press <UP> or <DOWN> until those numbers show 255.
d) Press <ENTER>.The next set of 3 digits on the display flashes.
e) Press <UP> or <DOWN> until those numbers show 255.
f) Press <ENTER>.The right-most set of 3 digits on the display flashes.
g) Press <UP> or <DOWN> until those numbers show 009.
h) Press <ENTER>.
i) Press <MENU> repeatedly until <IP Address #2> shows in the display.
j) Press <ENTER>. The left-most set of 3 digits on the display flashes.
k) Press <UP> or <DOWN> until those numbers show 255.
l) Press <ENTER>.The next set of 3 digits on the display flashes.
m) Press <UP> or <DOWN> until those numbers show 255.
n) Press <ENTER>.The right-most set of 3 digits on the display flashes.
o) Press <UP> or <DOWN> until those numbers show 011.
p) Press <MENU>.
4. Disable the unused DMX Out ports by doing the following for DMX Out ports 3 to 8:
a) Press <MENU> repeatedly until <DMX Output Port #X> shows on the display.
b) Press <ENTER>. The phrase in the lower right-hand corner of the display
flashes.

Configuration And Operation
Net-X™ User Manual Rev. 2 Page 17 of 
c) Press <UP> or <DOWN> until <Without Input> shows in the lower right-hand
corner.
d) Press <ENTER>. <Without Input> stops flashing.
5. Configure the DMX ports that will receive Art-Net™ signals by doing the following for
DMX Out ports 1 and 2:
a) Press <MENU> repeatedly until <DMX Output Port #X> shows on the display.
b) Press <ENTER>. The phrase in the lower right-hand corner of the display
flashes.
c) Press <UP> or <DOWN> until <ArtNet Input> shows in the lower right-hand
corner.
d) Press <ENTER>. <ArtNet Input> stops flashing.
6. Configure Art-Net™ universe for the DMX ports that will receive Art-Net™ by doing the
following:
a) <MENU> repeatedly until <Universe #1> shows in the display.
b) Press <ENTER>. The number in the lower right-hand corner of the display
flashes.
c) Press <UP> or <DOWN> until 4 shows on the display.
d) Press <ENTER>. 4 stops flashing.
e) <MENU> repeatedly until <Universe #2> shows in the display.
f) Press <ENTER>. The number in the lower right-hand corner of the display
flashes.
g) Press <UP> or <DOWN> until 8 shows on the display.
h) Press <ENTER>. 8 stops flashing.
Art-Net™ And DMX Sources
Art-Net™ and DMX sources configuration uses the Net-X™ as both a DMX splitter and
Art-Net™ adapter. Configure this operating mode by combining the configurations for the
DMX source and the Art-Net™ source, which are described in detail in DMX Source and
Art-Net™ Source. Keep the following in mind when configuring the Net-X™ for use as a
combination optical DMX splitter and Art-Net™ adapter.
• Disable any unused DMX Out ports.
• DMX Out ports can output only DMX or Art-Net™, not both.
Indicators
The three LED indicator lights on the front of the Net-X™, next to the menu display, indicate
when there is power, DMX, or Art-Net™. The table below shows the behavior of the lights
and what it means.
Indicator
Behavior
Meaning
POWER
Solid red
Power is getting to the Net-X™
Off
Power is not getting to the Net-X™
SIGNAL
Blinks rapidly in red
Art-Net™ signal is getting to the Net-X™
Blinks slowly
Art-Net™ signal is not getting to the Net-X™
DMX
Blinks rapidly in red
DMX signal is getting to the Net-X™
Blinks slowly
DMX signal is not getting to the Net-X™
While Net-X™ is powered on, the Signal and DMX indicator lights will
blink slowly when
nothing is plugged into their ports. These indicator lights will blink rapidly after cable
connections are made and the Art-Net™ and DMX signals are being received by Net-X™.

Technical Information
Page 18 of  Net-X™ User Manual Rev. 2
Technical Information 5.
Maintenance
To maintain optimum performance and minimize wear, the user should clean this product
regularly. Usage and environment are contributing factors in determining the cleaning
frequency.
As a rule, clean this product at least twice a month. Dust build-up reduces light output
performance and can cause overheating. This can lead to reduced light source life and
increased mechanical wear.
To clean the Net-X™, do the following:
1. Unplug the panel from power.
2. Wait until the unit is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the
external vents.
4. Clean all external surfaces with a mild solution of non-ammonia cleaner or isopropyl
alcohol.
5. Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
6. Make sure all connections are thoroughly dry before reconnecting power and signal
cables.
• Keep the environment around the Net-X™ free of dust, dirt, water, and extreme temperatures.
• Insert and remove DMX and Neutrik® etherCON® cables slowly and gently.
• Put the Net-X™ on the top of any stacks of equipment, or rack mount it.
• Turn the Net-X™ off when it is not in use.
Always dry the external surfaces carefully after cleaning them.

Technical Specifications
Net-X™ User Manual Rev. 2 Page 19 of 
Technical Specifications 6.
Dimensions And Weight
Length
Width
Height
Weight
19 in (483 mm)
6.6 in (168 mm)
1.8 in (45 mm)
4.4 lb (2.0 kg)
Power
Power Supply
Range
Voltage Selection
Switching (internal)
100 to 240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
208 V, 60 Hz
230 V, 50 Hz
Consumption
30 W
30 W
30 W
Operating Current
0.25 A
0.14 A
0.13 A
Power Connection
Power Input
Edison Plug to IEC (US/Canada)
Local plug to IEC (Worldwide)
IEC
Data Connections
I/O
Type
Data Inputs
Neutrik® etherCON® (2 total)
5-pin XLR (2 total)
Data Outputs
5-pin XLR (8 total)
Data Throughputs
Neutrik® etherCON® (2 total)
Ordering
Product Name
Item Code
UPC Number
Net-X™
03090868
781462212162

Returns
Page 20 of 0 Net-X™ User Manual Rev. 2
Returns
To return a product or request support:
• In the U.S., contact Chauvet World Headquarters (see Contact Us).
• In the UK or Ireland, contact Chauvet Europe Ltd. (see Contact Us).
• In Mexico, contact Chauvet Mexico (see Contact Us).
• In any other country, DO NOT contact Chauvet. Contact the distributor of record. See
www.chauvetlighting.com for a list of distributors.
If you live outside the U.S., United Kingdom, Ireland, or Mexico, contact your distributor of
record and follow their instructions on how to return Chauvet
products to them. Visit our
website for contact details.
Call the corresponding Chauvet Technical Support office and request a Return Merchandise
Authorization (RMA) number before shipping the product. Be prepared to provide the model
number, serial number, and a brief description of the reason for the return.
You must send the merchandise prepaid, in its original box, and with its original packing and
accessories. Chauvet will not issue call tags.
Clearly label the package with the RMA number. Chauvet
will refuse any product returned
without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number directly on
the box.
Before sending the product, clearly write the following information on a piece of paper and place
it inside the box:
• Your name
• Your address
• Your phone number
• RMA number
• A brief description of the problem
Be sure to pack the product properly. FedEx packing or double-boxing are recommended.
Chauvet
reserves the right to use its own discretion to repair or replace returned
product(s). Chauvet is not responsible for shipping damage of returned items.