Chauvet Intimidator Trio User manual

User Manual

Page 2 of 27 Intimidator Trio User Manual Rev. 1
TABLE OF CONTENTS
1. Before You Begin.......................................................................................................... 4
What Is Included .............................................................................................................................4
Unpacking Instructions....................................................................................................................4
Claims..................................................................................................................................................... 4
Text Conventions ............................................................................................................................4
Symbols ..........................................................................................................................................4
Disclaimer .......................................................................................................................................4
Product at a Glance ........................................................................................................................5
Safety Notes....................................................................................................................................5
2. Introduction................................................................................................................... 6
Product Overview............................................................................................................................6
Product Dimensions........................................................................................................................7
3. Setup.............................................................................................................................. 8
AC Power........................................................................................................................................8
Fuse Replacement..........................................................................................................................8
Power Linking......................................................................................................................................... 8
Mounting .........................................................................................................................................9
Orientation.............................................................................................................................................. 9
Rigging ................................................................................................................................................... 9
4. Operation......................................................................................................................10
Control Panel Operation................................................................................................................10
Menu Map .....................................................................................................................................10
Menu Map (cont.)..........................................................................................................................11
Configuration (DMX) .....................................................................................................................11
Starting Address................................................................................................................................... 11
DMX Personalities................................................................................................................................ 11
DMX Channel Assignments and Values.......................................................................................12
30CH .................................................................................................................................................... 12
Intimidator Trio Zones of Control .......................................................................................................... 12
30CH (cont.)......................................................................................................................................... 13
30CH (cont.)......................................................................................................................................... 14
30CH (cont.)......................................................................................................................................... 15
15CH .................................................................................................................................................... 16
15CH (cont.)......................................................................................................................................... 17
15CH (cont.)......................................................................................................................................... 18
Configuration (Standalone)...........................................................................................................19
Automatic Mode.................................................................................................................................... 19
Sound-Active Mode .............................................................................................................................. 19
Sound Sensitivity.................................................................................................................................. 19
Manual Mode........................................................................................................................................ 19
Totem Mode ......................................................................................................................................... 19
Pan/Tilt Orientation............................................................................................................................... 20
Pan/Tilt Angle Range............................................................................................................................ 20
Pan/Tilt Speed...................................................................................................................................... 20
Dimmer Curve....................................................................................................................................... 20
Dimmer Speed...................................................................................................................................... 20
Color Balance....................................................................................................................................... 21
Display Timeout.................................................................................................................................... 21
Display Orientation ............................................................................................................................... 21
Fans...................................................................................................................................................... 21
Reset.................................................................................................................................................... 21

Intimidator Trio User Manual Rev. 1 Page 3 of 27
Load Factory Defaults........................................................................................................................... 21
System Info........................................................................................................................................... 21
IR Mode.........................................................................................................................................22
IRC-6 Operation.................................................................................................................................... 22
Master/Slave Mode .......................................................................................................................23
5. Maintenance .................................................................................................................24
Product Maintenance....................................................................................................................24
6. Technical Specifications..............................................................................................25
Returns .............................................................................................................................26
Contact Us .........................................................................................................................27

Page 4 of 27 Intimidator Trio User Manual Rev. 1
1.BEFORE YOU BEGIN
What Is
Included
•Intimidator Trio
•Hanging Bracket with Mounting
Hardware
•Power Cord
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product
immediately and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with Chauvet within 7 days of delivery.
Text
Conventions
Convention
Meaning
1—512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol
Meaning
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all
respects. However, Chauvet assumes no responsibility and specifically disclaims any
and all liability to any party for any loss, damage or disruption caused by any errors or
omissions in this document, whether such errors or omissions result from negligence,
accident or any other cause. Chauvet reserves the right to revise the content of this
document without any obligation to notify any person or company of such revision,
how
ever, Chauvet has no obligation to make, and does not commit to make, any such
revisions. Download the latest version from www.chauvetlighting.com.
The works of authorship contained in this manual, including, but not limited to, all design,
text and images are owned by Chauvet.
© Copyright 2015 Chauvet & Sons, Inc. All rights reserved.
Electronically published by Chauvet in the United States of America.
CHAUVET, the Chauvet logo, Intimidator Trio, and Intimidator Wash Zoom are
registered trademarks or trademarks of Chauvet & Sons Inc. (d/b/a Chauvet and
Chauvet Lighting) in the United States and other countries.
Other company and product
names and logos referred to herein may be trademarks of their respective companies.

Intimidator Trio User Manual Rev. 1 Page 5 of 27
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Active
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about installation, usage, and maintenance.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power cord by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•Do not touch the product’s housing when operating because it may be very hot.
•The product is not intended for permanent installation.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket.
•The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Keep this User Manual for future use. If you sell the product to someone else, be
sure that they also receive this document.

Page 6 of 27 Intimidator Trio User Manual Rev. 1
2.INTRODUCTION
Product Overview
Front View
Back Panel View
Power Out
IR Sensor
Yoke
LCD
Display
Control
Buttons
DMX In/Out
Power In
Fuse-Holder
Indicator
Light

Intimidator Trio User Manual Rev. 1 Page 7 of 27
Product Dimensions
10.9 in
278 mm
15.2 in
386 mm

Page 8 of 27 Intimidator Trio User Manual Rev. 1
3.SETUP
AC Power
The Intimidator Trio has an auto-
ranging power supply and it can work with an input
voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s power
requirements (
circuit breaker, power outlet, and wiring), use the current value listed on
the label affixed to the product’s back panel, or refer to the product’s specifications chart.
The listed current rating indicates the product’s aver
age current draw under normal
conditions.
•Always connect the product to a protected circuit (circuit breaker or fuse).
Make sure the product has an appropriate electrical ground to avoid the risk
of electrocution or fire.
•To eliminate unnecessary wear and improve its lifespan, during periods of
non-use completely disconnect the product from power via breaker or by
unplugging it.
Never connect the product
to a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement
1. Disconnect the product from power.
2. Using a flat-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove the blown fuse.
4. Replace with a fuse of the same type and rating.
5. Screw the fuse holder cap back in place and reconnect power.
•Disconnect the product from the power outlet before replacing the fuse.
•Always replace a blown fuse with another of the same type and rating.
Power Linking
The product provides power linking via the IEC outlet located in the back of the product.
Please see the diagram below for further explanation.
Power Linking
Diagram
You can power link up to 4 Intimidator Trio products on 120 VAC or up to 8
Intimidator Trio products on 230 VAC.
The power linking diagram corresponds to the North American version of the
product ONLY! If using the product in other markets, you must consult with the
local Chauvet
distributor as power linking connectors and requirements may
differ in your country or region.
1st Product
2nd Product
3rd Product
Other products

Intimidator Trio User Manual Rev. 1 Page 9 of 27
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The Intimidator Trio
may be mounted in any position; however, make sure adequate
ventilation is provided around the product.
Rigging
•Before deciding on a location for the product, always make sure there is easy
access to the product for maintenance and programming purposes.
•Make sure that the structure or surface onto which you are mounting the product
can support the product's weight. See the Technical Specifications for weight
information. The CLP-15 clamp from Chauvet is appropriate for this product.
•When mounting the product overhead, always use a safety cable. Mount the
product securely to a rigging point, whether an elevated platform or a truss.
•When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity.
•When power linking multiple products, you must always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
•The rubber feet also serve as floor supports. When mounting the product on the
floor, make sure that the product and cables are away from people and vehicles.
Mounting Diagram
When using only one
mounting clamp with this fixture, you must use a clamp with
a captive bolt to prevent accidental loosening.
Safety Cable
Mounting Clamp
(works with CLP15 orCLP-
15N
clamp from Chauvet)
Mounting Bracket
Handle (x2)
Rubber Feet (x4)
for floor mounting
Mounting Hole for
Mounting Clamp
Mounting Holes for
Hanging/Mounting
Bracket
Safety Cable
Pass Through

Page 10 of 27 Intimidator Trio User Manual Rev. 1
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display. Please refer to the Product Overview to see the button locations
on the control
panel.
Button
Function
<MENU>
Press to find an operation mode or to back out of the current menu
option
<UP>
Press to scroll up the list of options or to find a higher value
<DOWN>
Press to scroll down the list of options or to find a lower value
<ENTER>
Press to activate a menu option or a selected value
Menu Map
Main Level
Programming Levels
Description
Address
001–512
Sets the DMX starting address
Run Mode
DMX
15CH
Selects DMX mode
30CH
Slave
Slave 1–4
Selects Slave mode
Auto
Selects Auto mode
Sound
Selects Sound-Active mode
IR
Selects Infrared mode
Manual
Pan
000–255
Manual pan control
Tilt
000–255
Manual tilt control
P/T Speed
000–255
Manual pan/tilt speed
Color
000–255
Manual color control
Rotate
000–255
Manual rotate control
Zoom
000–255
Manual zoom control
Dimmer
000–255
Manual dimmer controller
Shutter
000–255
Manual shutter control
Setup
Pan Reverse
OFF
Normal pan operation
ON
Reverse pan operation
Tilt Reverse
OFF
Normal tilt operation
ON
Reverse tilt operation
Pan Angle
540
Selects the 540° pan angle range
360
Selects the 360° pan angle range
180
Selects the 180° pan angle range
Tilt Angle
270
Selects the 270° tilt angle range
180
Selects the 180° tilt angle range
90
Selects the 90° tilt angle range
Totem Mode
OFF
Normal mode
UP
Totem Mode Base Up
DOWN
Totem Mode Base Down
P/T Speed
Normal
Selects the panning/tilting speed
Fast
Slow
Fans
Auto
Sets fan speed according to temperature
Full
Fan set to full speed
Display OFF
Display background light turns off after
inactivity
ON
Display background light stays on
Screen Rev
OFF
Normal display
ON
Reverse display

Intimidator Trio User Manual Rev. 1 Page 11 of 27
Menu Map
(cont.)
Main Level
Programming Levels
Description
Setup
(cont.)
Dimmer Curve
Square
Selects the dimmer curve mode
I Squa
sCurve
Linear
Dimmer Speed
Fast
Selects the dimmer speed
Smooth
Color
Balance
RED
100–255
Sets color balance (100 to 255)
GREEN
100–255
BLUE
100–255
WHITE
100–255
Sensitivity
001–100
Sets sound sensitivity
Reset
Resets the product
Factory Set
Loads factory defaults
Sys Info
Ver V_
Displays the software version
Running Mode _____
Displays the current running mode
DMX Address _ __
Displays the current DMX address
Temperature _ __
Displays the current LED temperature in
Celsius
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The Intimidator Trio uses up to 30 DMX channels in its 30-
channel DMX mode, which
defines the highest configurable address to 483.
If you are not familiar with the DMX protocol, download the DMX Primer from
www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Address.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select the starting address.
5. Press <ENTER>.
DMX
Personalities
The Intimidator Trio has two DMX personalities, a 30-channel personality and a 15-
channel personality.
To choose which DMX personality to use, follow the steps below:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Run Mode.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select DMX.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to choose either 30CH (to choose the 30-channel
personality) or 15CH (to choose the 15-channel personality).
7. Press <ENTER>.

Page 12 of 27 Intimidator Trio User Manual Rev. 1
DMX Channel Assignments and Values
30CH
Channel
Function
Value
Percent/Setting
1
Pan
000ó255 0–540°
2
Fine Pan
000ó255 Fine control of pan
3
Tilt
000ó255 0–270°
4
Fine Tilt
000ó255
Fine control of tilt
5
Pan/Tilt Speed
000ó255 Pan/Tilt speed (fast to slow)
6
Red 1
000ó255 0–100%
7
Green 1
000ó255 0–100%
8
Blue 1
000ó255
0–100%
9
White 1
000ó255 0–100%
10
Red 2
000ó255 0–100%
11
Green 2
000ó255 0–100%
12
Blue 2
000ó255
0–100%
13
White 2
000ó255 0–100%
14
Red 3
000ó255 0–100%
15
Green 3
000ó255 0–100%
16
Blue 3
000ó255
0–100%
17
White 3
000ó255 0–100%
18
No function
000ó255 Reserved for future use
19
No function
000ó255 Reserved for future use
20
No function
000ó255
Reserved for future use
21
No function
000ó255 Reserved for future use
Intimidator Trio Zones of Control
1
1
3
3
2
2

Intimidator Trio User Manual Rev. 1 Page 13 of 27
30CH
(cont.)
Channel
Function
Value
Percent/Setting
22 Colors
000
ó
004
No function
005
ó
009
Color 1
010
ó
014
Color 2
015ó019 Color 3
020
ó
024
Color 4
025
ó
029
Color 5
030ó034 Color 6
035
ó
039
Color 7
040
ó
044
Color 8
045
ó
049
Color 9
050
ó
054
Color 10
055
ó
059
Color 11
060
ó
064
Color 12
065
ó
069
Color 13
070
ó
074
Color 14
075
ó
079
Color 15
080
ó
084
Color 16
085
ó
089
Color 17
090ó094 Color 18
095
ó
099
Color 19
100
ó
104
Color 20
105
ó
109
Color 21
110
ó
114
Color 22
115ó119 Color 23
120
ó
124
Color 24
125
ó
129
Color 25
130
ó
134
Color 26
135
ó
139
Color 27
140ó144
Color 28
145
ó
149
Color 29
150
ó
154
Color 30
155
ó
159
Color 31
160
ó
164
Color 32
165ó169 Color 33
170
ó
174
Color 34
175
ó
179
No function
180
ó
201
Clockwise color change (fast to slow)
202
ó
207
Stop (color stays in the current color)
208ó229 Counter-clockwise color change (fast to slow)
230
ó
234
No function
235
ó
249
Color jump (fast to slow)
250ó255 Sound-Active colors

Page 14 of 27 Intimidator Trio User Manual Rev. 1
30CH
(cont.)
Channel
Function
Value
Percent/Setting
23 Built in Control
000
ó
015
No function
016
ó
031
Zone macro 1
032
ó
047
Zone macro 2
048ó063 Zone macro 3
064
ó
079
Zone macro 4
080
ó
095
Zone macro 5
096ó111 Zone macro 6
112
ó
127
Zone macro 7 (zone macros 1–6)
128
ó
143
Built-in Auto 1
144
ó
159
Built-in Auto 2
160
ó
175
Built-in Auto 3
176
ó
191
Built-in Auto 4
192
ó
207
Built-in Auto 5
208
ó
223
Built-in Auto 6
224
ó
239
Built-in Auto 7
240
ó
255
Built-in Auto 8 (built-in auto 1–7)
24
Built in Speed
000ó255 Zone macros and built-in auto speed (slow to fast)
25
Dimmer
000
ó
255
0–100%
26 Shutter
000
ó
019
Closed
020ó024 Open
025
ó
064
Strobe effect (fast to slow)
065
ó
069
Open
070
ó
084
Fast on, slow off (fast to slow)
085
ó
089
Open
090ó104 Slow on, fast off (fast to slow)
105
ó
109
Open
110
ó
124
Random shutter (fast to slow)
125
ó
129
Open
130
ó
144
Random fast on, slow off (fast to slow)
145ó149 Open
150
ó
164
Random slow on, fast off (fast to slow)
165
ó
169
Open
170
ó
184
Pulse effect 1 (fast to slow)
185
ó
189
Open
190ó204 Pulse effect 2 (fast to slow)
205
ó
209
Open
210
ó
224
Gradually on and off (fast to slow)
225
ó
229
Open
230
ó
244
Pulse effect 3 (fast to slow)
245ó255 Open
27
Zoom
000ó255
Zoom in and out

Intimidator Trio User Manual Rev. 1 Page 15 of 27
30CH
(cont.)
Channel
Function
Value
Percent/Setting
28 Control Functions
000ó009
No function
010
ó
014
Blackout while panning/tilting
015ó019
No function
020
ó
049
Reserved for future use
050ó054
Reset pan
055ó059
Reset tilt
060ó064
Reset zoom
065
ó
069
Reset rotation
070ó074
Reset all
075ó079
No function
080ó084
Reverse pan/tilt
085
ó
089
Reverse pan
090ó094
Reverse tilt
095ó099
Cancel reverse pan
100ó104
Cancel reverse tilt
105ó109
Cancel reverse pan/tilt
110
ó
114
Pan/Tilt normal speed
115ó119
Pan/Tilt fast speed
120
ó
124
Pan/Tilt slow speed
125ó129
Fan full speed
130ó134
Fan auto speed
135ó139
Dimmer fast
140
ó
144
Dimmer smooth
145ó255
No function
29 Movement Macros
000ó007
No function
008ó023
Automatic movement macro 1
024ó039
Automatic movement macro 2
040ó055
Automatic movement macro 3
056
ó
071
Automatic movement macro 4
072ó087
Automatic movement macro 5
088ó103
Automatic movement macro 6
104ó119
Automatic movement macro 7
120ó135
Automatic movement macro 8
136
ó
151
Sound-Active movement macro 1
152ó167
Sound-Active movement macro 2
168ó183
Sound-Active movement macro 3
184ó199
Sound-Active movement macro 4
200
ó
215
Sound-Active movement macro 5
216
ó
231
Sound-Active movement macro 6
232ó247
Sound-Active movement macro 7
248ó255
Sound-Active movement macro 8
30 Rotating
000ó063
Rotation indexing
When CH 27
(Zoom)
value is
above 150
064ó095
Rotating small shake (slow to fast)
096ó127
Rotating large shake (slow to fast)
128ó191
Rotating (slow to fast)
192ó255
Reverse rotating (slow to fast)

Page 16 of 27 Intimidator Trio User Manual Rev. 1
15CH
Channel
Function
Value
Percent/Setting
1
Pan
000
ó
255
0–540°
2
Tilt
000
ó
255
0–270°
3
Pan/Tilt Speed
000ó255 Pan/Tilt speed (fast to slow)
4
Red
000ó255
0–100%
5
Green
000
ó
255
0–100%
6
Blue
000
ó
255
0–100%
7
White
000ó255 0–100%
8 Built-in Control
000
ó
015
No function
016
ó
031
Zone macro 1
032
ó
047
Zone macro 2
048
ó
063
Zone macro 3
064ó079 Zone macro 4
080
ó
095
Zone macro 5
096
ó
111
Zone macro 6
112
ó
127
Zone macro 7 (zone macros 1–6)
128
ó
143
Built-in Auto 1
144
ó
159
Built-in Auto 2
160
ó
175
Built-in Auto 3
176
ó
191
Built-in Auto 4
192
ó
207
Built-in Auto 5
208
ó
223
Built-in Auto 6
224ó239 Built-in Auto 7
240
ó
255
Built-in Auto 8 (built-in auto 1–7)
9
Built-in Speed
000
ó
255
Zone macros and built-in auto speed (slow to fast)
10
Dimmer
000ó255 0–100%

Intimidator Trio User Manual Rev. 1 Page 17 of 27
15CH
(cont.)
Channel
Function
Value
Percent/Setting
11 Shutter
000ó019
Closed
020
ó
024
Open
025ó064
Strobe effect (fast to slow)
065
ó
069
Open
070ó084
Fast on, slow off (fast to slow)
085ó089
Open
090ó104
Slow on, fast off (fast to slow)
105
ó
109
Open
110ó124
Random shutter (fast to slow)
125ó129
Open
130ó144
Random fast on, slow off (fast to slow)
145
ó
149
Open
150ó164
Random slow on, fast off (fast to slow)
165ó169
Open
170ó184
Pulse effect 1 (fast to slow)
185ó189
Open
190
ó
204
Pulse effect 2 (fast to slow)
205ó209
Open
210
ó
224
Gradually on and off (fast to slow)
225ó229
Open
230ó244
Pulse effect 3 (fast to slow)
245ó255
Open
12
Zoom
000ó255 Zoom in and out
13 Control Functions
000ó009
No function
010ó014
Blackout while panning/tilting
015ó019
No function
020
ó
049
Reserved for future use
050ó054
Reset pan
055ó059
Reset tilt
060ó064
Reset zoom
065ó069
Reset rotation
070
ó
074
Reset all
075ó079
No function
080ó084
Reverse pan/tilt
085ó089
Reverse pan
090ó094
Reverse tilt
095
ó
099
Cancel reverse pan
100
ó
104
Cancel reverse tilt
105ó109
Cancel reverse pan/tilt
110ó114
Pan/Tilt normal speed
115ó119
Pan/Tilt fast speed
120
ó
124
Pan/Tilt slow speed
125ó129
Fan full speed
130ó134
Fan auto speed
135ó139
Dimmer fast
140ó144
Dimmer smooth
145
ó
255
No function

Page 18 of 27 Intimidator Trio User Manual Rev. 1
15CH
(cont.)
Channel
Function
Value
Percent/Setting
14 Movement Macros
000
ó
007
No function
008
ó
023
Automatic movement macro 1
024
ó
039
Automatic movement macro 2
040ó055 Automatic movement macro 3
056
ó
071
Automatic movement macro 4
072
ó
087
Automatic movement macro 5
088ó103 Automatic movement macro 6
104
ó
119
Automatic movement macro 7
120
ó
135
Automatic movement macro 8
136
ó
151
Sound-Active movement macro 1
152
ó
167
Sound-Active movement macro 2
168
ó
183
Sound-Active movement macro 3
184
ó
199
Sound-Active movement macro 4
200
ó
215
Sound-Active movement macro 5
216
ó
231
Sound-Active movement macro 6
232
ó
247
Sound-Active movement macro 7
248
ó
255
Sound-Active movement macro 8
15 Rotating
000
ó
063
Rotation indexing
When CH 27
(Zoom)
value is
above 150
064ó095
Rotating small shake (slow to fast)
096ó127
Rotating large shake (slow to fast)
128ó191
Rotating (slow to fast)
192
ó
255
Reverse rotating (slow to fast)

Intimidator Trio User Manual Rev. 1 Page 19 of 27
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
•Connect the product to power.
Never connect a product that is operating in any standalone mode (Automatic,
Sound-Active, or Manual
) to a DMX string connected to a DMX controller.
Products in standalone mode may transmit DMX signals that could interfere with
the DMX signals from the controller.
Automatic Mode
To enable the Automatic mode, do the following:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Run Mode.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Auto.
5. Press <ENTER>.
Sound-
Active
Mode
To enable the Sound-Active mode, follow the instructions below:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Run Mode.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Sound.
5. Press <ENTER>.
The product will only respond to low frequencies of music (bass and drums).
Sound Sensitivity
To set the sound sensitivity, do the following:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Sensitivity.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select 001-100, low to high.
7. Press <ENTER>.
Manual Mode
To test or control any function of the Intimidator Trio through the LCD display menu,
follow the instructions below:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Run Mode.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Manual.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select the function to test or control, from the options:
Pan, Tilt, P/T Speed, Color, Rotate, Zoom, Dimmer, and Shutter.
7. Press <ENTER>.
8. Use <UP> or <DOWN> to change the value of the selected function, from 000–255.
9. Press <ENTER>.
10. Repeat steps 6-9 until the functions are set as desired.
Totem Mode
To set the Intimidator Trio to Totem mode, do the following:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Totem Mode.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to choose OFF, DOWN, or UP.
7. Press <ENTER>.

Page 20 of 27 Intimidator Trio User Manual Rev. 1
Pan/Tilt
Orientation
To select whether the Intimidator Trio
will operate with normal panning or inverted
panning, follow the instructions below:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Pan Reverse.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select ON or OFF.
7. Press <ENTER>.
To select whether the Intimidator Trio will operate with normal tilting or inverted tilting, do
the following:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Tilt Reverse.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select ON or OFF.
7. Press <ENTER>.
Pan/Tilt Angle
Range
To select which pan angle range to use, follow the instructions below:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Pan Angle.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select 540, 360, or 180.
7. Press <ENTER>.
To select which tilt angle range to use, do the following.
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Tilt Angle.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select 240, 180, or 90.
7. Press <ENTER>.
Pan/Tilt Speed
To set the pan/tilt speed, follow the instructions below:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select P/T Speed.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select Normal, Fast, or Slow.
7. Press <ENTER>.
Dimmer Curve
To set the dimmer curve, do the following:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Dimmer Curve.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select Square, I Squa, sCurve, or Linear.
7. Press <ENTER>.
Dimmer Speed
To set the dimmer speed, follow the instructions below:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Dimmer Speed.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select Fast or Smooth.
7. Press <ENTER>.