Chauvet SX Mix User manual

SX Mix™ Snapshot
Ok on Dimmer
Outdoor OK
Sound Activated
DMX512
Master/Slave
115V/230V Switch
Replaceable Fuse
User Serviceable
Duty Cycle
USER MANUAL
Chauvet, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A.
[phone] – [phone]
FAX [phone]
www.chauvetlighting.com

TABLE OF CONTENTS
1. BEFORE YOU BEGIN................................................................................................................................ 3
WHAT IS INCLUDED......................................................................................................................................... 3
UNPACKING INSTRUCTIONS ............................................................................................................................. 3
AC POWER ................................................................................................................................................... 3
CONTACT US................................................................................................................................................. 3
SAFETY INSTRUCTIONS................................................................................................................................... 4
Duty Cycle............................................................................................................................................... 4
2. INTRODUCTION ........................................................................................................................................ 5
FEATURES..................................................................................................................................................... 5
PRODUCT OVERVIEW ..................................................................................................................................... 5
3. SETUP........................................................................................................................................................ 6
LAMP............................................................................................................................................................ 6
Lamp Installation..................................................................................................................................... 6
FUSE REPLACEMENT...................................................................................................................................... 7
MOUNTING .................................................................................................................................................... 7
Orientation ........................................................................................................................................ 7
Rigging ............................................................................................................................................. 7
4. OPERATING INSTRUCTIONS................................................................................................................... 7
GENERAL TROUBLESHOOTING......................................................................................................................... 8
TECHNICAL SUPPORT ..................................................................................................................................... 9
5. APPENDIX.................................................................................................................................................. 9
GENERAL MAINTENANCE ................................................................................................................................9
RETURNS PROCEDURE................................................................................................................................... 9
CLAIMS ........................................................................................................................................................10
TECHNICAL SPECIFICATIONS ..........................................................................................................................10
SX Mix Manual 2 2006-12-11/15:22

1. BEFORE YOU BEGIN
What is included
¾1 x SX Mix™
¾ELC3 24V 250W Lamp
¾Warranty Card
¾User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
AC Power
To determine the power requirements for a particular fixture, see the label affixed to the back plate of
the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average
current draw under normal conditions. All fixtures must be powered directly off a switched circuit and
cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch. Before applying power to a fixture, check that the
source voltage matches the fixture’s requirement.
Warning! Verify that the voltage required by your unit matches the line voltage applied.
Damage to your fixture may result if the line voltage applied does not match the
voltage required by the fixture. All fixtures must be connected to circuits with a
suitable Earth Ground.
Contact Us
World Wide
General Information Chauvet Lighting
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084
Technical Support Chauvet Lighting
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)
World Wide Web www.chauvetlighting.com
SX Mix Manual 3 2006-12-11/15:22

Safety Instructions
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance of this
product.
xPlease keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
xAlways make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
xThis product is intended for indoor use only!
xTo prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no
flammable materials close to the unit while operating.
xThe unit must be installed in a location with adequate ventilation, at least 20 inches (50cm) from
adjacent surfaces. Be sure that no ventilation slots are blocked.
xAlways disconnect from power source before servicing or replacing lamp or fuse and be sure to
replace with same lamp source.
xSecure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use
its carrying handles.
xMaximum ambient temperature (Ta) is 95°F (35°C). Do not operate fixture at temperatures higher
than this.
xIn the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
xDon’t connect the device to a dimmer pack.
xMake sure the power cord is never crimped or damaged.
xAvoid direct eye exposure to the lamp while it is on.
Caution! There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET.
Duty Cycle
This fixture has a 15/15 duty cycle, meaning it can be run for fifteen minutes, and then must be left off
for 15 minutes before it is turned on again.
SX Mix Manual 4 2006-12-11/15:22

2. INTRODUCTION
Features
xHigh-speed multi-function gobo moonflower effect
xSeparate moonflower and color/gobo wheel
xCombined color/gobo wheel:
18 gobos
22 colors
xDual function switches:
Color wheel: select sound active or continuous rotation
Moonflower: select sound active or continuous rotation
xElectronic transformer
xFan cooled
Product Overview
Fuse
Focusing
Lens
Gobo
Mode
Switch
Moonflower
Mode
Switch
Hanging
Bracket
Microphone
Power Cord
SX Mix Manual 5 2006-12-11/15:22

3. SETUP
Lamp
You will need to install a lamp prior to the initial operation of the fixture. A 250W lamp is included.
Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the
unit to cool down! Always disconnect from main power prior to lamp replacement.
Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp
with alcohol and wipe it with a lint free cloth before installation.
Lamp Installation
Figure A
Figure B
1) Open the top cover by removing the s
screws indicated in Figure A.
ix
loth.
2) Lift the lamp and socket vertically away
from the fixture.
3) Remove the lamp from the socket.
4) Hold the new lamp with a lint-free c
Insert the lamp into the socket.
5) Reinsert the lamp into the fixture.
6) Replace the top cover.
SX Mix Manual 6 2006-12-11/15:22

Fuse Replacement
Disconnect the power cord before replacing a fuse and always
replace with the same type fuse.
The fuse is located
inside this
compartment.
Remove using a flat
head screwdriver. FUSE
With a flat-head screwdriver, unscrew the fuse
holder from its housing. Remove the damaged
fuse from its holder and replace with exact
same type fuse. Insert the fuse holder back in
its place and reconnect power.
Mounting
ORIENTATION
This fixture may be mounted in any position provided there is adequate room for ventilation.
RIGGING
Hanging Clamp
It is important never to obstruct the fan or vents pathway. Mount the
fixture using, a suitable “C” or “O” type clamp. Adjust the angle of the
fixture by loosening both knobs and tilting the fixture. After finding the
desired position, retighten both knobs.
xWhen selecting installation location, take into consideration lamp
replacement access and routine maintenance.
xSafety cables should always be used. Note!
Clam
xNever mount in places where the fixture will be exposed to rain, high
humidity, extreme temperature changes or restricted ventilation.
p
is sold se
p
aratel
y
.
4. OPERATING INSTRUCTIONS
1) Use the moonflower mode switch to set the mode of rotation (up = continuous rotation mode,
down = sound-active mode).
2) Use the gobo mode switch to set the mode of rotation (up = continuous rotation mode, down =
sound-active mode).
3) Turn the focusing lens to focus the beam onto your projection surface.
SX Mix Manual 7 2006-12-11/15:22

General Troubleshooting
Applies to
Symptom Solution(s)
Lights
Foggers
& Snow Controllers
Dimmers
& Chaser
Auto shut off Check fan thermal switch reset 9
Beam is very dim or not
bright
Clean optical system or replace lamp
Check 220/110v switch for proper setting
9
Breaker/Fuse keeps
blowing
Check total load placed on device 9
Chase is too slow Check users manual for speed adjustment 999
Device has no power Check for power on Mains.
Check device’s fuse. (internal and/or external)
999
Fixture is not
responding
Check DMX Dip switch settings for correct addressing
Check DMX cables
Check polarity switch settings
9
Fixture is on but there
is no movement to the
audio
Make sure you have the correct audio mode on the control
switches. If audio provided via ¼” jack, make sure a live
audio signal exists
Adjust sound sensitivity knob
999
Lamps cuts off
sporadically
Possible bad lamp or fixture is overheating.
Lamp may be at end of its life.
9
Light will not come on
after power failure
Some discharge lamps require a cooling off period before
the electronics in the fixture can kick start it again, wait 5 to
10 minutes before powering up
9
Loss of signal Use only DMX cables
Install terminator
Note: Keep DMX cables separated from power cables or
black lights.
99 9 9
Moves slow Check 220/110v switch for proper setting 9
No flash Re-install bulb, may have shifted in shipping 9
No laser output Bounce mirror motor may have shifted during shipping,
readjust 9
No light output Check slip ring & brushes for contact
Install bulb
Call service technician
9
Relay will not work Check reset switch
Check cable connections
9
Remote does not work Make sure connector is firmly connected to device 99
Stand alone mode All Chauvet lighting fixtures featuring stand-alone functions
do not require additional settings, simply power the fixture
and it will automatically enter into this mode
9
If you still have a problem after trying the above solutions, please contact CHAUVET Technical
Support at the location on the next page.
SX Mix Manual 8 2006-12-11/15:22

Technical Support
Address: Service Dept.
3000 N 29th Ct, Hollywood, FL 33020 (U.S.A.)
Support (Email): [email protected]
Telephone: [phone] - (Press 4)
Fax: [phone] - (Attention: Service)
Website: http://www.chauvetlighting.com
5. APPENDIX
General Maintenance
To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.
Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust
collected on external vents and internal components. Clean all glass when the fixture is cold with a
mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply
solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical
surfaces until they are free of haze and lint.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s
optics. Clean with soft cloth using normal glass cleaning fluid. - Always dry the parts carefully. - Clean
the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products
returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause
for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate
packaging is the customer’s responsibility. CHAUVET reserves the right to use its own discretion to
repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe
method to use.
Note: If you are given an RA #, please include the following information on a piece of paper
inside the box:
1) Your name
2) Your address
3) Your phone number
4) The RA #
5) A brief description of the symptoms
SX Mix Manual 9 2006-12-11/15:22

Claims
Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.
Technical Specifications
WEIGHT & DIMENSIONS
Length.............................................................................................................................. 13 in (330 mm)
Width ............................................................................................................................ 12.5 in (318 mm)
Height .................................................................................................................................7 in (178 mm)
Weight ..............................................................................................................................6.8 lbs (3.1 kg)
POWER
Fixed power settings (not selectable)........................................................ 120V 60Hz AC or 230V 50Hz
Fuse.........................................................................................................................................6.3A 250V
Power Consumption ................................................................................................................228W Max
Inrush Power .................................................................................................................................. 252W
LIGHT SOURCE
Lamp....................................................................................................................ELC3 24V 250W Lamp
PHOTO OPTIC
Beam Angle........................................................................................................................................ 35°
THERMAL
Maximum ambient temperature.............................................................................................95°F (35°C)
ORDERING INFORMATION
SX Mix ......................................................................................................................................... SX-MIX
WARRANTY INFORMATION
Warranty .............................................................................................................. 1-year limited warranty
SX Mix Manual 10 2006-12-11/15:22