Chauvet SlimPAR TRI 7 IRC User manual

User Manual

Page 2 of 18 SlimPAR™ Tri IRC series User Manual (Rev. 5)
TABLE OF CONTENTS
1. Before You Begin ...........................................................................................................3
What Is Included .........................................................................................................................3
Unpacking Instructions ................................................................................................................3
Claims .................................................................................................................................................3
Text Conventions ........................................................................................................................3
Symbols ......................................................................................................................................3
Disclaimer ...................................................................................................................................3
Product at a Glance.....................................................................................................................4
Safety Notes ...............................................................................................................................4
2. Introduction ....................................................................................................................5
Product Overview (SlimPAR™ Tri 12 IRC) ..................................................................................5
Product Overview (SlimPAR™ Tri 7 IRC) ....................................................................................6
Product Dimensions (SlimPAR™ Tri 12 IRC)...............................................................................7
Product Dimensions (SlimPAR™ Tri 7 IRC).................................................................................8
3. Setup...............................................................................................................................9
AC Power....................................................................................................................................9
Fuse Replacement ...............................................................................................................................9
Power Linking .................................................................................................................................... 10
Mounting ...................................................................................................................................11
Orientation.........................................................................................................................................11
Rigging.............................................................................................................................................. 11
4. Operation ......................................................................................................................12
Control Panel Operation............................................................................................................12
Menu Map.................................................................................................................................12
Configuration (DMX)..................................................................................................................13
Starting Address ................................................................................................................................ 13
Configuration (Standalone)........................................................................................................13
Automatic Mode................................................................................................................................. 13
Static Color Mode .............................................................................................................................. 13
Custom Static Color Mode..................................................................................................................13
Master/Slave Mode ............................................................................................................................ 14
Infrared Control.................................................................................................................................. 14
IRC (Infrared Remote Control) Operation............................................................................................ 15
DMX Channel Assignments and Values.....................................................................................16
7-CH..................................................................................................................................................16
3-CH..................................................................................................................................................16
5. Technical Information ..................................................................................................16
Product Maintenance ................................................................................................................16
Returns .....................................................................................................................................17
CHAUVET® Contact Information...............................................................................................17
6. Technical Specifications..............................................................................................18

SlimPAR™ Tri IRC series User Manual (Rev. 5) Page 3 of 18
1. BEFORE YOU BEGIN
What Is
Included
•SlimPAR™ Tri IRC (7 or 12)
•Power Cord
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product immediately and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and
included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as
missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of delivery.
Text
Conventions
Convention Meaning
1~512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this document are subject to change
without notice. CHAUVET® assumes no responsibility or liability for any errors or
omissions that may appear in this manual.
CHAUVET® reserves the right to update the
existing document or to create a new document to correct any errors or omissions.
You can download the latest version of this document from www.chauvetlighting.com.
© Copyright 2012 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Author Date Editor Date
A. Diaz 9/16/11 S. Diaz 9/6/12

Page 4 of 18 SlimPAR™ Tri IRC series User Manual (Rev. 5)
Product at a
Glance
Use on Dimmer

Auto Programs

Outdoor Use

Auto-ranging Power Supply

Sound Activated

Replaceable Fuse

DMX

User Serviceable

Master/Slave

Duty Cycle

Safety Notes
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about installation, usage, and maintenance.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power cord by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•Do not touch the product’s housing when operating because it may be very hot.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in (50
cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
•The maximum ambient temperature is 104° F (40° C). Do not operate the product at
higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•Keep this User Manual for future consultation. If you sell the product to another
user, be sure that they also receive this document.

SlimPAR™ Tri IRC series User Manual (Rev. 5) Page 5 of 18
2. INTRODUCTION
Product Overview (SlimPAR™ Tri 12 IRC)
LED Display
Power In
DMX Out
Safety Loop
DMX In
Bracket
Adjustment Knob
Fuse Holder
Power Out

Page 6 of 18 SlimPAR™ Tri IRC series User Manual (Rev. 5)
Product Overview (SlimPAR™ Tri 7 IRC)
LED Display
Power In
DMX Out
DMX In
Bracket
Adjustment Knob
Fuse Holder
Power Out
Safety Loop

SlimPAR™ Tri IRC series User Manual (Rev. 5) Page 7 of 18
Product Dimensions (SlimPAR™ Tri 12 IRC)

Page 8 of 18 SlimPAR™ Tri IRC series User Manual (Rev. 5)
Product Dimensions (SlimPAR™ Tri 7 IRC)

SlimPAR™ Tri IRC series User Manual (Rev. 5) Page 9 of 18
3. SETUP
AC Power
The SlimPAR™ Tri IRC series has an auto-
ranging power supply and it can work with an
input voltage range of 100~240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product’s back panel, or
refer to the product’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit
(circuit breaker or fuse). Make
sure the product has
an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product to
a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement
Disconnect the product from the power outlet before replacing the fuse.
1. Disconnect the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the fuse holder out of the housing.
4. Remove the blown fuse from the holder.
5. Replace with a fuse of the exact same type and rating.
6. Insert the fuse holder back in place and reconnect power.
A spare fuse is not included; however, the safety cap has room for a spare.
Always replace a blown fuse with the same type and rating.
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap

Page 10 of 18 SlimPAR™ Tri IRC series User Manual (Rev. 5)
Power Linking
The product provides power linking via the Edison outlet located in the back of the unit..
Power Linking Diagram
You can power link up to 23 SlimPAR™ Tri 7 IRC units on 120 VAC or up to 39
SlimPAR™ Tri 7 IRC units on 230 VAC.
You can power link up to 15 SlimPAR™ Tri 12 IRC units on 120 VAC or up to 26
SlimPAR™ Tri 12 IRC units on 230 VAC.
The power linking diagram shown above corresponds to the North American
version of the product ONLY! If using the product
in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
requirements may differ in your country or region.
1st Product
2nd Product
3rd Product
Other products

SlimPAR™ Tri IRC series User Manual (Rev. 5) Page 11 of 18
Mounting
Before mounting the product, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The SlimPAR™ Tri IRC series may be mounted in any position; however, make sure
adequate ventilation is provided around each product.
Rigging
•Before deciding on a location for the product, always make sure there is easy
access to the product for maintenance and programming purposes.
•Make sure that the structure or surface onto which you are mounting the product
can support the product’s weight (see the Technical Specifications).
•When mounting the product overhead, always use a safety cable.
Mount the
product securely to a rigging point, whether an elevated platform or a truss.
•When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity.
•When power linking multiple products, you must always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
•The bracket adjustment knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
•The double-bracketed yoke/mounting brackets/rubber feet/metallic feet
also serve
as floor supports/allow for surface mounting. When mounting the product
on the
floor, make sure that the product and cables are away from people and vehicles.
Mounting Diagram
(SlimPAR™ Tri 12 IRC
shown)
Gel Frame Holder
Bracket
Adjustment Knob
Mounting Bracket
Gel Frame

Page 12 of 18 SlimPAR™ Tri IRC series User Manual (Rev. 5)
4. OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display. Please refer to the Product Overview to see the button locations
on the control
panel.
Button Function
<MENU> Press to find an operation mode or to back out of the current menu
option
<UP> Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower value
<ENTER> Press to activate a menu option or a selected value
Menu Map
Mode
Programming Steps
Description
3-CH d001-512 3 channel DMX mode (RGB)
7-CH
d001-512
7-channel DMX mode
C--
C1
Red
Static color
C2 Green
C3 Blue
C4 Cyan
C5
Magenta
C6 Yellow
C7
White
P--
P1 7-color program (switching)
P2 7-color program (fading)
P3 3-color program (switching)
P4
3-color program (fading)
P-- P5 7-color program (sound active)
P6 3-color program (sound active)
S-- S--1-100 Program speed for P1-P4
U--
A-- Red
(r000-100)
Custom Static Colors
Combine red, green, and blue
g-- Green
(r000-100)
b-- Blue
(r000-100)
SEr On Turns infrared on or off
Off

SlimPAR™ Tri IRC series User Manual (Rev. 5) Page 13 of 18
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Starting Address
When selecting a starting DMX address,
always consider the number of DMX channels
the selected DMX mode uses. If you
choose a starting address that is too high, you
could restrict the access to some of the product’s channels.
The SlimPAR™ Tri IRC series uses up to 7 DMX channels in its 7-channel
DMX mode,
which defines the highest configurable address to 506.
If you are not familiar with the DMX protocol, you may refer to the DMX Primer section in
the Technical Information chapter.
To select the starting address, do the following:
1. Press <MENU> repeatedly until 3-CH or 7-CH shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
Never connect a product that is operating in any standalone mode (either Static or
Automatic) to a DMX string connected to a DMX controller. Products in standalone
mode may transmit DMX
signals that could interfere with the DMX signals from
the controller.
Automatic Mode
To enable the Automatic Mode, follow the instructions below:
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to choose an auto program (P1-P6).
4. Press <ENTER>.
5. To adjust the speed of the program, press <MENU> until S-- shows on the display.
6. Press <ENTER>.
7. Use <UP> or <DOWN>
to adjust the duration of each step of the automatic program
from S__1 (fast) to S100 (slow).
8. Press <ENTER>.
Static Color Mode
To enable the Static Color Mode, follow the instructions below:
1. Press <MENU> repeatedly until C-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to choose a color. (C1-C7)
4. Press <ENTER>.
Custom Static
Color Mode
To enable the Custom Static Color Mode, follow the instructions below:
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> to choose between colors (R--, g--, b--).
4. Press <ENTER>.
5. Press <UP> or <DOWN> to choose the intensity of the color (000-100).
6. Repeat the steps to mix additional colors to create the color you need.

Page 14 of 18 SlimPAR™ Tri IRC series User Manual (Rev. 5)
Master/Slave
Mode
The Master/Slave mode allows a single SlimPAR™ Tri IRC series unit (the “master”) to
control the actions of one or more SlimPAR™ Tri IRC series
units (the “slaves”) without
the need of a DMX controller. The master unit will be set to operate in either Automatic
or Static Color mode, while the slave units will be set to operate in Slave Mode. Once set
and connected, the slave units will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1. Press <MENU> repeatedly until 3-CH shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to 001.
4. Connect the DMX input of the first slave unit to the DMX output of the master unit.
5. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
6. Finish setting and connecting all the slave units.
Master unit:
1. Set the master unit to operate in either Automatic or Static Color mode.
2. Make the master unit the first unit in the DMX daisy chain.
•Configure
all the slave units before connecting the master unit to the DMX
daisy chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with the signals from the master
unit.
•Do not connect more than 31 slave units to the master unit.
•When using the Master/Slave mode
with the IRC, set the slave units to
7-channel mode to ensure the best performance.
Infrared Control
The SlimPAR™ Tri IRC series is fully compatible with the IRC Infrared Remote Control
from CHAUVET®. To enable usage with the IRC, follow the instructions below:
1. Press <MENU> repeatedly until SEr shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> to turn the feature on or off.
4. Press <ENTER>.
For IRC operation instructions, refer to the following page.

SlimPAR™ Tri IRC series User Manual (Rev. 5) Page 15 of 18
IRC (Infrared Remote
Control) Operation
Automatic Mode
Automatic Mode will enable you to run the automatic programs on the
product.
To turn on Automatic Mode:
1. Press AUTO on the IRC.
2. Press + or – to choose between the different auto programs.
To adjust the speed of the automatic program:
1. Press SPEED on the IRC.
2. Press %.
3. Press + or – to either increase or decrease the speed of the program.
Sound-Active Mode
Sound Active Mode will enable the product to respond to the music.
To turn on Sound Active mode:
1. Press SOUND on the IRC.
To adjust sound sensitivity in Sound Active mode:
1. Press SENSITIVITY on the IRC.
2. Press %.
3. Press + or – to either increase or decrease sound sensitivity.
Manual Color Control
To choose a specific color with the IRC:
1. Press MANUAL on the IRC.
2. Press any number between 0-9 to choose your color.
To manually control the RGB percentage:
1. Press MANUAL on the IRC.
2. Press R, G, or B to choose your color.
3. Press + or – to increase or decrease the percentage of each color.
Miscellaneous Operation
To adjust the strobe rate of the program:
1. Press STROBE on the IRC.
2. Press + or – to increase or decrease the strobe rate.
3. Press STROBE again to turn off the strobe.
To change the switching effect of the program:
Press FADE/SNAP on the IRC.
Fade will slowly switch the effect. Snap will rapidly switch the effect.
To black out the lights:
Press BLACK OUT on the IRC.
This will turn off all the lights until the button is pressed again.
Note: The IRC will not respond to any inputs when Black Out is activated. If
the remote does not respond when a button is pressed, try pressing
BLACK OUT. You may have inadvertently activated BLACK OUT.

Page 16 of 18 SlimPAR™ Tri IRC series User Manual (Rev. 5)
DMX Channel Assignments and Values
7-CH
Channel Function Value Setting
1
Red
000 255
0~100%
2
Green
000 255
0~100%
3
Blue
000

255
0~100%
4
Color Macros
(overrides CH. 1-3)
000 015
No function
016 255
Color Macros
5
Speed
(when CH.6 is 032~223)
000 255 0~100%
Strobe
000 015
No function
016 255
Slow to fast
6 Mode
000 031
RGB Mode
032 063
Pulse effect 0~100%
064 095
Pulse effect 100%~0
096

127
Pulse effect 100%~0~100%
128 159
Auto fade transition
160 191
Auto snap transition (3 colors)
192 223
Auto snap transition (7 colors)
224 255
Sound-Active mode
7
Dimmer
000 255
0~100%
3-CH
Channel Function Value Setting
1
Red
000 255
0~100%
2
Green
000 255
0~100%
3
Blue
000 255
0~100%
5. TECHNICAL INFORMATION
Product
Maintenance
Dust build-
up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life and mechanical wear. To maintain optimum
performance and minimize wear, clean the product at least twice a month. However,
usage and environmental conditions contribute to increased cleaning frequency.
To clean the product, follow the instructions below:
•Unplug the product from power.
•Wait until the product is cold.
•Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
•Clean all glass/transparent surfaces with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
•Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
•Softly drag any dirt or grime to the outside edge of the glass/transparent surface.
•Gently polish the glass/transparent surfaces until they are free of haze and lint.
Always dry the glass/transparent surfaces carefully after cleaning them.

SlimPAR™ Tri IRC series User Manual (Rev. 5) Page 17 of 18
To return a product or request support:
•In the U.S., contact CHAUVET® World Headquarters (see below).
•In the UK or Ireland, contact CHAUVET® Europe Ltd. (see below).
•In any other country, DO NOT contact CHAUVET®. Contact your distributor. See
www.chauvetlighting.com for distributors outside the U.S., United Kingdom, or
Ireland..
If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of
record and follow their instructions on how to return CHAUVET® products to
them. Visit our website for contact details.
Returns
Call the corresponding CHAUVET®
Technical Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
return.
You must send the merchandise pr
epaid, in its original box, and with its original packing
and accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET®
will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA
number
directly on the box.
Before sending the product, clearly write
the following information on a piece of paper
and place it inside the box:
•Your name
•Your address
•Your phone number
•The RMA number
•A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. FedEx packing or double-
boxing are
recommended.
CHAUVET®
reserves the right to use its own discretion to repair or replace
returned product(s).
CHAUVET®
Contact
Information
World Headquarters
CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
United Kingdom & Ireland
CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [e-mail]
Technical Support
Email: [e-mail]
World Wide Web
www.chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk

Page 18 of 18 SlimPAR™ Tri IRC series User Manual (Rev. 5)
6. TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length (Tri 12)
Width (Tri 12)
Height (Tri 12)
Weight (Tri 12)
9.5 in (235 mm)
4.6 in (115 mm)
11.5 in (292 mm)
5.7 lbs (2.6 kg)
Length (Tri 7)
Width (Tri 7)
Height (Tri 7)
Weight (Tri 7)
7.7 in (195 mm)
4.6 in (118 mm)
8.5 in (215 mm)
3.8 lbs (1.7 kg)
Note: Dimensions in inches rounded to the nearest decimal digit
Note: Unless otherwise indicated, all specifications are applicable to both the SlimPAR™ Tri 7 IRC
and the SlimPAR™ Tri 12 IRC.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100~240 V, 50/60 Hz
Auto-ranging
SlimPAR™ Tri 12 IRC
120 V, 60 Hz
230 V, 50 Hz
Consumption
64 W
67 W
Operating
0.5 A
0.3 A
Power linking current (units)
8 A (15 units)
8 A (26 units)
Fuse
F 1 A, 250 V
F 1 A, 250 V
SlimPAR™ Tri 7 IRC
120 V, 60 Hz
230 V, 50 Hz
Consumption
42 W
47 W
Operating
0.3 A
0.2 A
Power linking current (units)
8 A (23 units)
8 A (39 units)
Fuse
F 1 A, 250 V
F 1 A, 250 V
Power I/O
US/Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (U.S.)
Local plug
Light Source
Type
Power
Lifespan
LED
1 W
50,000 hours
Parameter
SlimPAR™ Tri 12 IRC
SlimPAR™ Tri 7 IRC
Color
Tri-color
Tri-color
Quantity
12
7
Current
350 mA (x 3)
350 mA (x 3)
Photo Optic
Parameter
SlimPAR™ Tri 12 IRC
SlimPAR™ Tri 7 IRC
Illuminance @ 2 m
2,662 lux
1,073 lux
Beam angle
20º
20º
Field angle
34º
34º
Thermal
Maximum External Temp.
Cooling System
104° F (40° C)
Convection
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Sockets
3, 7
Ordering
Product Name
Item Code
Item Number
SlimPAR™ Tri 12 IRC
03030405
SLIMPARTRI12IRC
SlimPAR™ Tri 7 IRC
03030404
SLIMPARTRI7IRC