Chauvet Followspot 1200 User manual

User Manual

Edition Notes
Followspot 1200 User Manual Rev. 5
Edition
Notes
CHAUVET® released this edition of the Followspot 1200 User Manual Rev. 05 in
March 2012.
The Followspot 1200 User Manual Rev. 05 covers the description, safety precautions,
installation, programming, operation and maintenance of the Followspot 1200.
Trademarks
CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or
Chauvet). The CHAUVET® logo in its entirety including the Chauvet name and the
dotted triangle, and all other trademarks on this manual pertaining to services, products
or marketing statements (example: It’s Green Thinking™) are owned or licensed by
CHAUVET®. Any other product names, logos, brands, company names, and other
trademarks featured or referred to within this document are the property of their
respective trademark holders.
Copyright
Notice
CHAUVET® owns the content of this user manual in its entirety, including but not
limited to pictures, logos, trademarks and resources.
© Copyright 2012 CHAUVET®
All rights reserved
Electronically published by CHAUVET® in the United States of America
Manual
Usage
CHAUVET® authorizes its customers to download and print this manual for
professional information purposes only. CHAUVET® expressly prohibits the usage,
copy, storage, distribution, modification or printing of this manual or its content for any
other purpose without its written consent.
Document
Printing
For better results, print this document in color, on letter size paper (8.5 x 11 inches),
double sided. If using A4 paper (210 x 297 mm), configure your printer to scale the
content of this document to A4 paper.
Intended
Audience
Any person in charge of installing, operating and/or maintaining the Follows
pot 1200
should read the Quick Start Guide that shipped with the Followspot 1200 unit and this
manual in their entirety before installing, operating or maintaining the Followspot 1200.
Disclaimer
CHAUVET® believes that the information contained in this manual is accurate in all
respects. However, CHAUVET® assumes no responsibility for any error or omissions
in this document. CHAUVET® reserves the right to revise this document and to make
changes from time to time in the content hereof without obligation of CHAUVET® to
notify any person or company of such revision or changes. This does not constitute in
any way a commitment by CHAUVET® to make such changes. CHAUVET® may issue
a revision of this manual or a new edition of it to incorporate such changes.
CHAUVET®
Publications
Hot Line
If you have any comments about the accuracy of this document or general suggestions
regarding how we can improve it, please call us at [phone] (US callers) or +1-
954-929-1115 (international callers), ext. 43.
You can download the latest versions of all CHAUVET® products’ manuals from
www.chauvetlighting.com.
Document
Revision
The Followspot 1200 User Manual Rev. 05
supersedes all previous versions of this
manual.
Please discard any older versions of this manual you may have, whether in printed or
electronic format, and replace them with this version.
Fixture at
a Glance
Use on Dimmer

Auto Programs

Outdoor Use

208/230 V, 50/60 Hz

Sound Activated

Replaceable Fuse

DMX

User Serviceable

Master/Slave

Duty Cycle


Table of Contents
-a- Followspot 1200 User Manual Rev. 5
Table of Contents
1. Before you Begin.............................................................................................................1
What is Included.............................................................................................................................1
Unpacking Instructions ...................................................................................................................1
Text Conventions............................................................................................................................1
Icons ..............................................................................................................................................1
Safety Notes...................................................................................................................................2
2. Introduction.....................................................................................................................3
System Description.........................................................................................................................3
Features.........................................................................................................................................3
Additional Features....................................................................................................................................3
DMX Channel Summary.................................................................................................................3
6-channel DMX mode ................................................................................................................................3
Product Overview...........................................................................................................................4
Product Dimensions .......................................................................................................................5
3. Setup................................................................................................................................6
AC Power.......................................................................................................................................6
Power Requirements..................................................................................................................................6
Power Cord ...............................................................................................................................................6
Fuse Replacement.....................................................................................................................................6
Voltage/Frequency Selection......................................................................................................................7
Lamp..............................................................................................................................................8
Lamp Removal...........................................................................................................................................8
Lamp Installation........................................................................................................................................9
DMX Linking.................................................................................................................................10
DMX Connection......................................................................................................................................10
Mounting......................................................................................................................................11
Orientation...............................................................................................................................................11
Rigging....................................................................................................................................................11
4. Operation.......................................................................................................................12
Control Panel Description.............................................................................................................12
Programming Panel.................................................................................................................................12
Navigation Functions................................................................................................................................12
Followspot 1200 Menu Options.....................................................................................................13
Normal Mode...........................................................................................................................................13
Offset Mode.............................................................................................................................................13
Programming Procedure...............................................................................................................14
Normal Mode...........................................................................................................................................14
Normal Mode (Cont.)................................................................................................................................15
Offset Mode.............................................................................................................................................15
External Console..........................................................................................................................16
Controls...................................................................................................................................................16
DMX Controller Operation.............................................................................................................17
DMX Values.................................................................................................................................17
6-CH........................................................................................................................................................17
5. Technical Information...................................................................................................17
Maintenance.................................................................................................................................17
Returns ........................................................................................................................................18
Claims..........................................................................................................................................18
Contact Us ...................................................................................................................................18
Technical Specifications...............................................................................................................19

Before you Begin
-1- Followspot 1200 User Manual Rev. 5
1. Before you Begin
What is
Included
•One Followspot 1200 Fixture
•One External Console
•One Tripod
•One Flight Case
•Warranty Card
•Quick Reference/Start Guide
Unpacking
Instructions
The Followspot 1200 ships in a flight case, Immediately upon receiving the fixture,
carefully unpack the flight case. Check the flight case contents to ensure that all parts
are present and that they are in good condition. If any part appears damaged from
shipping, or if the flight case shows signs of mishandling, notify the shipper
immediately. In addition, retain the flight case and all the packing material for
inspection.
In any event, save the flight case and all packing material because, in case that you
have to return the fixture to the factory, you will have to do so in its original flight case,
with all its original packing. See the Claims section in the Technical Information
chapter.
Text
Conventions
Convention Meaning
1~512
A range of values
50/60
A set of mutually exclusive values in the text
[10]
A DIP switch to be configured
Claims
A fixture function, a new term, a section or a chapter
“COLORado™ UM”
The name of another publication or manual
<SET>
A key to be pressed on the fixture’s control panel
Settings
A menu option that can be selected but not modified
MENU > Settings
A sequence of menu options to be followed
[1~10]
A range of menu values of which one can be selected
Yes/No
A set of mutually exclusive menu options to choose
ON
A value to be entered or selected
Icons
Icons Meaning
This icon indicates critical installation, configuration or operation
information. Failure to comply with this information may render
the fixture partially or completely inoperative, damage third-
party equipment, or cause harm to the user.
This icon indicates important installation or configuration
information. Failure to comply with this information may prevent
the fixture from functioning correctly.
Useful information.

Before you Begin
Followspot 1200 User Manual Rev. 5 -2-
Safety
Notes
Please read the following notes
carefully because they include important safety
information about the installation, usage and maintenance of this product.
It is important to read all these notes before starting to work with this product.
There are no user-serviceable parts inside the Followspot 1200. Any reference to
servicing this unit you may find from now on in this User Manual will only apply
to properly CHAUVET® certified technicians. Do not open the housing or attempt
any repairs unless you are one of them.
Please refer to all applicable local codes and regulations for proper installation
of the Followspot 1200.
Keep this manual for future consultation. If you sell the Followspot 1200 to
another user, make sure that they also receive this manual.
•The Followspot 1200 housing weighs 94 lbs (42.6 kg). Always ask for help when
mounting this fixture to avoid personal injuries or damage to the unit.
•Always connect the Followspot 1200 to a grounded circuit to avoid the risk of
electrocution.
•Avoid direct eye exposure to the light source while the Followspot 1200 is on.
•Lamp explosion hazard! Do not open the lamp cover within five minutes of having
turned off the fixture.
•The bulb remains hot for a long time after turn off. Never touch the bulb
barehanded and always hand it by its metallic contacts.
•Always disconnect the Followspot 1200 from its power source before servicing.
•Do not touch the Followspot 1200’s housing when operating because it may reach
up to 85º C.
•This product is for indoor use only! To prevent risk of fire or shock, do not expose
this product to rain or moisture.
•Make sure there are no flammable materials close to the fixture(s) while operating.
•When hanging this fixture, always secure it to a fastening device using a safety
cable (not provided).
•Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the fixture at
a higher temperature.
•Always make sure that you are connecting the Followspot 1200 to the proper
voltage, as per the specifications in this manual or on the product.
•Never connect the Followspot 1200 to a dimmer pack.
•Never disconnect the power to the fixture by pulling or tugging on the power cable.
•Make sure the power cord is not crimped or damaged.
•In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your Followspot 1200 may require service, please
contact CHAUVET® Technical Support.

Introduction
-3- Followspot 1200 User Manual Rev. 5
2. Introduction
System
Description
The Followspot 1200 is a DMX compatible follow spot fixture that uses a 1200 W metal
halide lamp and features a high efficiency optical assembly, a high quality dichroic color
wheel and an external console.
This fixture consists of a housing unit that contains the power supply, the control panel,
the lamp and the optical assembly. The housing has a yoke for tripod mounting. The
Followspot 1200 ships with an external console already mounted on its handle. In
addition, the Followspot 1200 includes a stand-alone, adjustable height tripod.
The 5-pin DMX input and output sockets for DMX connectivity are on the control panel,
while there is another 5-pin XLR socket dedicated to the external console. The
Followspot 1200 features a bright 4-digit display and four buttons to perform all its
programming functions.
The external console features four sliders and several buttons to control the fixture in a
stand-alone fashion. However, the user can connect the Followspot 1200 to a DMX
daisy chain data link to control it from a standard DMX controller, along with other DMX
compatible fixtures.
Features
•Metal Halide 1200W lamp
•6-Channel DMX mode
Functions: shutter, iris, color, color temperature, dimmer and focus
•Color Wheel 1
8 dichroic colors + white
Rainbow color spin at variable speeds
Split/Linear Colors
•Color Wheel 2
2 dichroic colors + white
CTC filter: 3,200 K / Frost / Open
•Variable electronic iris (4~38⁰)
•Variable electronic dimmer (0~100%)
•Variable electronic focus
•Blackout shutter button
Additional Features
•External control console
•Tripod
•Flight case
DMX Channel Summary
6-channel DMX mode
DMX Channel Function
1
Shutter
2
Iris
3
Color
4
Color temperature
5
Dimmer
6
Focus

Introduction
Followspot 1200 User Manual Rev. 5 -4-
Product Overview
For details about the Control Panel, refer to the Fuse Replacement and DMX
Linking sections in the Setup chapter as well as the Operation chapter.
For details about the external console, refer to the External Console section of
the Operation chapter.
Housing
Fans
Yoke
Tripod
Safety
loop
Knob
Control Panel
External Console

Introduction
-5- Followspot 1200 User Manual Rev. 5
Product Dimensions

Setup
Followspot 1200 User Manual Rev. 5 -6-
3. Setup
AC Power
The Followspot 1200 has two AC input voltage settings, 208 and 230 VAC, and two AC
frequency settings, 50 and 60 Hz. The voltage and frequency settings require changing
the connections on the corresponding terminal strip. See the
Voltage and Frequency
Selection section in this chapter.
Always connect the Followspot 1200 to a protected circuit with an appropriate
electrical ground to avoid the risk of electrocution or fire.
Power Requirements
To determine the power requirements for the Followspot 1200
see the label affixed to
the fixture. Alternatively, you may refer to the specifications chart in the Technical
Information chapter of this manual.
The listed current rating indicates the maximum current draw during normal operation.
Please refer to the Sizing the Circuit Breakers section in the Appendix chapter of this
manual.
Power Cord
The fixture side of the Followspot 1200’s power cord enters the control panel through a
strain relief boot. This side of the power cord is hard-wired to the fixture. Therefore,
there is no removable power connector on the control panel.
The outlet side of the power cord is bare-ended. This way, the users will be able to
equip it with the power plug that best matches the local standards and regulations.
Power Cord Pin Out
Connection
Wire (U.S.)
Wire (Europe)
IP-66 Pin
Screw Color
AC Live
Black Brown 1 Yellow or Brass
AC Neutral White Blue 2 Silver
AC Ground Green/Yellow Green/Yellow 3 Green
Never connect the Followspot 1200 to a rheostat (variable resistor) or dimmer
circuit, even if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse Replacement
1) With a Philips screwdriver, unscrew the fuse holder out of its housing and remove
the blown fuse from its holder.
2) Replace the blown fuse with a fuse of the exact same type and rating.
3) Replace the fuse holder in its place, and reconnect power.
Make sure to disconnect the fixture’s power cord before replacing a blown fuse,
and always replace it with a fuse of the same type and rating.
Fuse Holder Diagram
Illuminated
On/off Switch
Fuse Holder
Power Cord
Rubber Boot

Setup
-7- Followspot 1200 User Manual Rev. 5
Voltage/Frequency
Selection
The Followspot 1200 uses a single terminal strip to select the operating voltage and
frequency. This operation only requires connecting two wires to a terminal strip, as
indicated below.
Do not connect the fixture to the power outlet without having selected the
voltage and frequency first. Make sure that the circuit’s voltage and frequency
matches your selection to avoid unstable operation or damage to the fixture.
Make sure that there is no power applied to the fixture before op
ening the
fixture’s housing.
Opening the Fixture
1) Unfasten the thumbscrew (T) and slide the front cover (FC) slightly forward.
2) Unscrew the two Allen screws (A) and remove the bracket (B).
3) Carefully pick up and slide the back cover (BC) backward, making sure not to pull
the wires that run from its fans to the Fan Control PCB inside the housing.
Cover Removal
Diagram
Two black wires arrive to the terminal strip (TS). One wire labeled “1” and the other
labeled “2.”
1) Connect the black wires as needed per the table below, without reversing them.
2) Replace the covers.
3) Replace the bracket and secure it with the two Allen screws.
Voltage/Frequency
Terminal Strip
Voltage/Frequency
Selection Table
Voltage/Frequency Wire #1 Wire #2
208 V, 50 Hz Terminal #2 Terminal #4
208 V, 60 Hz Terminal #2 Terminal #3
230 V, 50 Hz Terminal #1 Terminal #6
230 v, 60 Hz Terminal #1 Terminal #5
A
TS
BC
B
FC
T

Setup
Followspot 1200 User Manual Rev. 5 -8-
Lamp
The user may have to install the lamp before operating the Followspot 1200 for the first
time.
The instructions below include the steps to remove an existing lamp as well as to install
a new lamp.
Lamp Removal
Removing an already installed lamp requires caution. Follow the steps indicated below
to complete the removal in a safe manner.
Make sure that there is no power applied to the fixture before opening the
fixture’s housing.
Lamp explosion hazard! Wait 15 minutes after having turned off the fixture to
open the lamp cover.
Opening the Fixture
1) Unfasten the thumbscrew (T) and slide the front cover (FC) slightly forward.
2) Loosen the thumbscrew that hold the lamp cover (LC) and lift it to expose the lamp
socket.
Lamp Removal
Diagram
Always wear safety goggles and soft gloves when handling the lamp.
The bulb remains hot for a long time after turn off.
Never touch the bulb barehanded and always hand it by its metallic contacts.
Removing an
Existing Lamp
1) Once you have access to the lamp, loosen both lamp end screws.
2) Grab the lamp by both lamp end screws, push it evenly against the clips and then
slide it upwards until it is free.
3) Place the lamp in an appropriate container for disposal.
Always follow local regulations regarding the disposal of used metal halide
lamps.
T
FC
LC
L

Setup
-9- Followspot 1200 User Manual Rev. 5
Lamp Installation
Installing a new lamp requires caution. Follow the steps indicated below to complete
the lamp installation in a safe manner.
If you touched the lamp with your bare hands, make sure to clean it thoroughly
(contacts, glass necks and glass globe) with isopropyl alcohol and wipe it with a
lint-free cloth before installing it. Otherwise, the fingerprints on the lamp may
shorten its life and even cause damage to the optical assembly.
Follow all the safety instructions indicated on page 8.
Installing a
New Lamp
1) If installing a new lamp, open the Followspot 1200 as indicated on page 8.
2) Before installing the lamp, loosen its end screws.
3) Hold the lamp by its metallic contacts and slide it into the slots.
4)
Ensure that the flat washers on the lamp shafts are on the thumbscrewside of the
slot to ensure maximum contact.
5) Evenly push the clips backward to allow the lamp to go all the way into the slots.
6) Rotate the lamp until the nipple is on the top of the bulb.
7) Tighten the lamp end screws.
8) Once installed, the lamp should look as in the diagram bellow.
Lamp Installation
Diagram
Closing the Fixture
1) Close the lamp cover and tighten the thumbscrew that holds it.
2) Slide the front cover backward until it touches the bracket.
3) Tighten the thumbscrew to secure the front cover.
Reflector
Lamp end
screw
Lamp end
screw
Bulb
nipple
Contact
plate
Clip
Clip
Fixture’s
front
Lamp
contact
Contact
plate
Flat
washer

Setup
Followspot 1200 User Manual Rev. 5 -10-
DMX Linking
If you are using the Followspot 1200 with a DMX controller, you ca
n link them using a
regular DMX serial connection. Be aware that the Followspot 1200 uses 5-pin XLR
connectors and that you will need a 5-pin to 3-pin adapter in most cases.
If you are not familiar with the DMX standard, please refer to the DMX Primer and DMX
Connectivity sections in the Appendix chapter of this manual.
The Followspot 1200 does not support the Master/Slave mode.
DMX Connection
The Followspot 1200 uses the regular DMX data connection for its only 6-
channel DMX
mode. Refer to the Introduction chapter for a brief description of this mode and the
Operation chapter to learn how to configure the Followspot 1200 to work in this mode.
The diagram below shows the Followspot 1200 DMX connectors.
DMX Connectors Diagram
Pins 4 and 5 of the External Console Only socket carry power for the external
console. Therefore, DO NOT connect the DMX cable to this socket. Otherwise,
you could damage the DMX controller or the fixtures connected to the DMX link.
1) Connect the DMX cable that comes from the DMX controller or from the other DMX
fixtures to the DMX Input socket.
2) Connect the DMX cable that goes to the other DMX fixtures to the DMX Output
socket.
When using the Followspot 1200’s external console, DO NOT
connect the
Followspot 1200 to the DMX link.
The diagram below illustrates a typical DMX link connection.
DMX Link Diagram
External Console Only
DMX Input
DMX Output

Setup
-11- Followspot 1200 User Manual Rev. 5
Mounting
Orientation
Always mount this fixture in any safe position while making
sure that there is adequate
room around it for ventilation. Make sure to mount this fixture away from any flammable
material as indicated in the Safety Notes.
Rigging
The Followspot 1200 consists of a housing unit and a tripod (included)
. CHAUVET
recommends following the general guidelines below when mounting the Followspot
1200 and its tripod on top of a suitable platform.
•When selecting an installation location, consider ease of access to the fixture for
operation, programming adjustments and routine maintenance.
•Never mount the fixture in places where rain, high humidity, extreme temperature
changes or restricted ventilation may affect it.
•Make sure that the location where you are mounting the fixture can support its
weight (84 lbs / 38 kg) as well as the operator’s weight.
Product
Mounting
Diagram
As an extra measure to reduce vibrations and to prevent the fixture from tipping
over, weight down the tripod arms or anchor them to the mounting platform.
Tripod
leg
Carrying
handles
(both sides)
Yoke
Swivel
tripod top
Safety loop
(both sides)
Tilt
adjustment
knob
(+45 ~-45º)

Appendix
Followspot 1200 User Manual Rev. 5 -12-
4. Operation
Control Panel
Description
The Followspot 1200’s control panel includes the Programming Panel, the Power Panel
and the DMX Panel. Refer to page 6 for a description of the Power Panel, and to page
10 for a description of the DMX Panel.
The Programming Panel allows the user to configure the Followspot 1200’s functions
with a 4-
digit blue LED display and four buttons located directly under the LED display.
The table below explains the functions of those buttons.
Programming
Panel
Button Function
<MENU> Used to scroll to a function or to
return to a previous menu option
<ENTER>
Selects a menu option
<UP> Scrolls through the menu
options in ascending (forward)
order
<DOWN> Scrolls through the menu
options in descending
(backward) order
Navigation Functions
The Followspot 1200’s navigation functions allow the user to setup all the fixture’s
parameters, as described in the Menu Map and the programming procedures.
Display
The Followspot 1200’s display has four 7-segment, blue LED modules.
Function Change
To select a function, press <MENU> repeatedly
until the desired function shows on the
display.
Alternatively, if the display shows a function name, you could press <UP> or <DOWN>
to look for another function.
Function Selection
To select a function, press <ENTER>. The display will start blinking.
To exit the current function without making any change, press <MENU>.
Function Value
Press <UP> or <DOWN> to select a value for the current function while the display is
blinking.
Saving a Value
While the display is blinking, press <ENTER>to save the selected value for the current
function.
Function Timer
After selecting a function value, you have eight seconds to press <ENTER> to save the
value on the display. Otherwise, the display will exit the current function without saving
the new value.
Programming Modes
The Followspot 1200 has two programming modes, Normal and Offset. The Normal
mode is for regular operation, while the Offset mode is for home adjustments.

Appendix
-13- Followspot 1200 User Manual Rev. 5
Followspot 1200 Menu Options
Normal Mode
Function 1
st
Level 2
nd
Level Description
DMX Address 1~255 Selects the fixture’s DMX address
Color Black Out Yes/No Enables/disables the black out while changing colors
Self-test N/A Runs the built-in self-test program
Fixture Hours N/A Shows the amount of hours the fixture has been on
Lamp On/Off On/Off Turns the lamp on or off
Reset N/A Resets the fixture to its factory default settings
Offset Mode
Function
1st Level
2nd Level
Description
Color Offset -127~127 Performs the fine position adjustment for the color wheel
Effect Offset -127~127 Performs the fine position adjustment for the effects wheel
Dimmer Offset -127~127 Performs the fine position adjustment for the dimmer

Appendix
Followspot 1200 User Manual Rev. 5 -14-
Programming
Procedure
The Followspot 1200 programming requires only three menu levels and it uses two
programming modes, Normal and Offset.
The Offset mode is for home adjustments of the color, the dimmer and the effects.
When not in program mode, the display shows the current DMX address.
Normal Mode
The Normal mode controls the DMX address, the control activation, the lamp on/off
status, the running of the self-test and the fixture reset. In addition, it shows the number
of hours the fixture has been in service.
DMX Address
Defines the fixture’s starting address
1) Press <MENU> repeatedly until the display shows
2) Press <ENTER> to show the current DMX address (1~255).
The display will start blinking.
3) To exit without changing the value, press <MENU>.
4) To change the address value, press <UP> or <DOWN>.
5) To save the new value, press <ENTER>.
The display will show the next function name.
Color Wheel Blackout
Enables/disables the blackout fixture whilechanging colors
1) Press <MENU> repeatedly until the display shows
2) Press <ENTER> to show the current setting (Yes/No).
The display will start blinking.
3) To exit without changing the value, press <MENU>.
4) To change the setting, press <UP> or <DOWN>.
5) To save the new value, press <ENTER>.
The display will show the next function name.
Self-test
Runs the built-in self-tests
1) Press <MENU> repeatedly until the display shows
The display will start blinking.
3) Press <ENTER> to start the tests.
The display will stop blinking and the tests will start to run continuously.
5) To suspend the tests for 30 seconds, press <ENTER>.
6) To terminate the tests, press <MENU>.
The display will show the next function name.
Fixture Hours
Shows the number of hours the fixture has been in service
1) Press <MENU> repeatedly until the display shows
The display will start blinking.
2) Press <ENTER> to see the number of hours.
3) To exit, press <MENU>.
The display will show the next function name.

Appendix
-15- Followspot 1200 User Manual Rev. 5
Normal Mode (Cont.)
Lamp
Turns the lamp on or off
1) Press <MENU> repeatedly until the display shows
The display will start blinking.
2) Press <ENTER>.
The display will show the current lamp status (On/Off).
Lamp Off
3) To turn the lamp off, press <UP> or <DOWN> until the display shows off.
4) Press <ENTER> to save the change.
The display will stop blinking and the lamp will turn off immediately.
In eight seconds, the display will start showing the current DMX address.
Lamp On
5) To turn the lamp on, press <UP> or <DOWN> until the display shows on.
6) Press <ENTER> to save the change.
The display will stop blinking and the lamp will start to turn on immediately.
In eight seconds, the display will start showing the current DMX address.
Reset
Resets all the settings to their factory defaults
1) Press <MENU> repeatedly until the display shows
The display will start blinking.
2) Press <ENTER> to start the defaulting process.
The display will stop blinking and it will show 1200.
All DMX channels will return to their default settings.
The reset function does not affect the Fixture Hours total.
Offset Mode
The Offset mode provides fine position adjustment for the co
lor wheel, the effects (color
temperature) wheel and the dimmer. These fine adjustments allow the operator to
position the wheels so the light goes through the center of the color or effect aperture,
thus preventing any filter border from showing. In the case of the dimmer, the fine
adjustment ensures that at 0% dimmer (maximum light), the dimmer is not affecting the
light beam.
Entering Offset Mode
1) Press <MENU> for five seconds.
The display will show the first offset mode function.
Color Offset
Performs the fine position adjustment for the color wheel
1) Press <UP> or <DOWN> repeatedly until the display shows
2) Press <ENTER>.
The display will start blinking, showing the current value (-127~127).
3) Press <UP> or <DOWN> to set the new value.
4) Press <ENTER> to save the new value or <MENU> to exit without saving.
Effect Offset
Performs the fine position adjustment for the effects wheel
1) Press <UP> or <DOWN> repeatedly until the display shows
2) Press <ENTER>.
The display will start blinking, showing the current value (-127~127).
3) Press <UP> or <DOWN> to set the new value.
4) Press <ENTER> to save the new value or <MENU> to exit without saving.

Appendix
Followspot 1200 User Manual Rev. 5 -16-
Offset Mode (Cont.)
Dimmer Offset
Performs the fine position adjustment for the dimmer
1) Press <UP> or <DOWN> repeatedly until the display shows
2) Press <ENTER>.
The display will start blinking, showing the current value (-127~127).
3) Press <UP> or <DOWN> to set the new value.
4) Press <ENTER> to save the new value or <MENU> to exit without saving.
Exiting Offset Mode
1) After you are done, wait eight seconds for the display timer to activate.
The display will show the current DMX address.
External
Console
The external console ships already installed on the Followspot 1200 handle. This
console has dedicated sliders and buttons to control only the associated fixture.
In addition, the external console connects to the Followspot 1200 using a dedicated 5-
pin XLR connector on the control panel.
Pins 4 and 5 of the External Console Only socket carry power for the external
console. Therefore, DO NOT connect the DMX cable to this socket. Otherwise,
you could damage the DMX controller or the fixtures connected to the DMX link.
Controls
The external console controls have pre-assigned functions and labels. This simplifies
the fixture’s operation.
When the Followspot 1200 is in any of its programming modes, the external
console is not operational.
External Console Diagram
Dimmer
The dimmer has a Blackout and an Open button. This allows the operator to keep the
slider at a fixed position when closing the dimmer to 0% or opening it to 100%.
When the dimmer is open after having pressed the Open button, the operator can
resume the sl
ider control by gently touching the slider. Resuming slider control after
blacking out the dimmer is not possible, however.
Shutter
The shutter has no fixed position buttons to operate along with the slider. This slider
has a closed and an open posit
ion on the left side, while the right side has another
open position.
The shutter frequency changes from short yet separated openings to a fast strobe-like
action as the slider moves from left to right.
Iris
The iris has a Closed and an Open button. As with the dimmer, this allows the operator
to keep the slider at a fixed position when closing the iris to its
minimum or opening it to
its maximum.
The slider operation can resume by slightly touching the slider after having set the iris
to either its maximum or minimum aperture by using the corresponding button.
Focus
The focus control has no fixed buttons to operate along the slider, either. The focus
changes from near to far as theslider moves from left to right.
Color Control
The button on the left lower corner of the console determines the way the color
changes. If it is in the Fixed Color position, buttons 1 to 9 determine the color. If it is in
the Color Scroll position, buttons 1 to 9 determine the scrolling speed (slow to fast).
Color Temperature
The color temperature control is independent from the color control mode. It has three
positions, 6000º K, Frost and 3200º K.