Chauvet Batten 80i User manual

C
O
O
LORa
C
do™
B
C
hauvet, 3000 N 29
t
(800) 762
FA
X
www.
B
atten
8
USE
R
t
h
Ct, Hollywood, F
L
-1084 – (954) 929-1
X
[phone]
chauvetlighting.co
m
8
0i
R
MAN
U
L
33020 U.S.A.
115
m
U
AL
S
S
R
U
S
naps
h
OK on Di
m
Outdoor
O
S
ound Acti
v
DMX5
1
Master/S
l
Autoswitc
h
Transfor
m
R
eplaceabl
e
U
ser Servi
c
Dut
y
C
yc
h
ot
m
mer
O
K
v
ated
1
2
l
ave
h
in
g
m
er
e
Fuse
c
eable
c
le

TABLE OF CONTENTS
1. Before You Begin...................................................................................................................................... 3
What is included.............................................................................................................................................. 3
Unpacking Instructions.................................................................................................................................... 3
Safety Instructions .......................................................................................................................................... 4
LED Expected Lifespan .................................................................................................................................. 4
2. Introduction............................................................................................................................................... 5
Features.......................................................................................................................................................... 5
DMX Channel Summary ................................................................................................................................. 6
Product Overview............................................................................................................................................ 8
3. Setup.......................................................................................................................................................... 9
AC Power........................................................................................................................................................ 9
Mounting....................................................................................................................................................... 10
Orientation .................................................................................................................................................... 10
Rigging.......................................................................................................................................................... 10
Lens Assembly Installation/Replacement ..................................................................................................... 11
Fixture Linking............................................................................................................................................... 12
Data Cabling................................................................................................................................................. 12
DMX Data Cable........................................................................................................................................... 12
Cable Connectors......................................................................................................................................... 12
3-Pin to 5-Pin Conversion Chart ................................................................................................................... 13
Setting up a DMX Serial Data Link................................................................................................................ 13
Master/Slave Fixture Linking............................................................................Error! Bookmark not defined.
4. Operating Instructions............................................................................................................................ 14
Control Options............................................................................................................................................. 14
COLORado ™ Control Quick Setup.............................................................................................................. 14
DMX-512 control without “ID” address.......................................................................................................... 14
DMX-512 addressing with ID address........................................................................................................... 15
Setting the DMX address.............................................................................................................................. 15
Control Panel Functions................................................................................................................................ 15
Manual Power ON/OFF ................................................................................................................................ 16
Menu Map..................................................................................................................................................... 17
DMX512 Channel Values.............................................................................................................................. 18
Important Notes about STAGE 1 .................................................................................................................. 29
Important Notes about STAGE 2 .................................................................................................................. 30
Important Notes about Block 1,2,3,4............................................................................................................. 30
Technical Support......................................................................................................................................... 31
Contact Us.................................................................................................................................................... 31
5. Appendix.................................................................................................................................................. 32
DMX Primer .................................................................................................................................................. 32
General Maintenance.................................................................................................................................... 33
Returns Procedure........................................................................................................................................ 33
Claims........................................................................................................................................................... 33
COLORado ™Batten 80i Service Maintenance Guide.................................................................................. 34
Blow-out Diagram ......................................................................................................................................... 35
Photometric................................................................................................................................................... 35
PCB Line Drawings....................................................................................................................................... 37
Technical Specifications ............................................................................................................................... 39
COLORado™ Batten 80i User Manual 2 5/19/2008 10:40 AM

1. BEFORE YOU BEGIN
What is included
¾1x COLORado™ Batten 80i
¾1x Mounting Bracket/Floor Stand
¾1x Neutrik Power cable with plug
¾1x Neutrik Power linking cable
¾1x Warranty Card
¾1x User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
COLORado™ Batten 80i User Manual 3 5/19/2008 10:40 AM

Safety Instructions
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance of this
product.
•Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Always make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
•The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect from power source before servicing or replacing lamp or fuse and be sure to
replace with same lamp source.
•Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use
its carrying handles.
•Maximum ambient temperature (Ta) is 104°F (40°C). Do not operate fixture at temperatures higher
than this.
•In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•Never connect the device to a dimmer pack.
•Make sure the power cord is never crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
•Avoid direct eye exposure to the light source while it is on.
•Do not daisy chain power to more than 4 or 9 units @120volts.
Caution! There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET at: 954-929-1115.
Caution! After prolonged periods of operation, the fixture chassis may reach high
temperatures. Use caution when handling this fixture.
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the
acceleration of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in
ideal or singular optimum conditions. For this reason when all color LEDs are used at their fullest
intensity, life of the LEDs is significantly reduced. It is estimated that a viable lifespan of 40,000 to
50,000 hours will be achieved under normal operational conditions. If improving on this lifespan
expectancy is of a higher priority, place care in providing for lower operational temperatures. This
may include climatic-environmental and the reduction of overall projection intensity
COLORado™ Batten 80i User Manual 4 5/19/2008 10:40 AM

2. INTRODUCTION
Features
•3, 4, 9, 12, 16, 60 or 80-channel DMX-512 LED bank system (with ID addressing)
•Operating modes
3-channel: RGB control
3-channel: HSV control (hue, saturation and value)
4-channel: RGBW control
9-channel: RGBW, ID, dim, macro, automatic, custom, balance, Hyper Color™
12-channel: RGBW, ID, dim, macro, automatic, custom, vector, balance, Hyper Color™
16-channel: RGBW of 4 separate sections
60-channel: individual control of each LED (for pixel mapping, excluding white)
80-channel: individual control of each LED (for pixel mapping)
•RGBW color mixing with or without DMX controller
•Color temperature presets (3,200ºK - 10,000ºK) or create your own
•Built-in automated programs via master/slave or DMX
•Program and recall custom programs via master/slave or DMX
•Adjustable fan speeds
ADDITIONAL FEATURES
•High-power, 2W Red (350mA) 3W Green, Blue, White (700mA)LEDs
•Hyper Color™ allows the LEDs to be driven at higher current for increased output
•Additional power output: max 4 or 9 units @ 120V
•LCD display with password protection
•Battery-powered display for setup without power
OPTIONS
•Optical systems available: 10°, 15°(installed), 30°
COLORado™ Batten 80i User Manual 5 5/19/2008 10:40 AM

DMX Channel Summary
The COLORado™ Batten 80i has a total of 11 DMX channel configurations, referred to as “Personalities” in this manual
and in the fixture onboard control board. The 8 personalities are [BLOCK 1, BLOCK 2, BLOCK 3, BLOCK 4, HSV, STAGE
1, STAGE 2, ARC1, ARC 2, PIXEL 1, and PIXEL 2]. Each of the different personalities can be accessed from the control
board. Please see section on “Control Panel Functions” on a description on how to accomplish this.
[STAGE 1] CHANNEL DESCRIPTION
1 Dimmer
2 Red
3 Green
4 Blue
5 White
6 Color Macro / White Balance / Hyper Color
7 Strobe
8 Auto & Custom Programs
9 Auto speed
10 ID Address Selection
[STAGE 2] CHANNEL DESCRIPTION
1 Dimmer
2 Red
3 Green
4 Blue
5 White
6 Color Macro / White Balance / Hyper Color
7 Strobe
8 Auto & Custom Programs
9 Auto Speed
10 ID Address
11 Module Selection
12 Module & Color Macro Selection
[ARC 1] CHANNEL DESCRIPTION
1 Red
2 Green
3 Blue
[ARC 2] CHANNEL DESCRIPTION
1 Red
2 Green
3 Blue
4 White
COLORado™ Batten 80i User Manual 6 5/19/2008 10:40 AM

[PIXEL 1] CHANNEL DESCRIPTION
1 Pixel 1 Red
2 Pixel 1 Green
3 Pixel 1 Blue
4-60 Repeat Ch.1~Ch.3 (pixel1, pixel 2, pixel 3, etc)
[PIXEL 2] CHANNEL DESCRIPTION
1 Pixel 1 Red
2 Pixel 1 Green
3 Pixel 1 Blue
4 Pixel 1 White
5-80 Repeat Ch.-1~Ch.4 (pixel1, pixel 2, pixel 3, etc)
[BLOCK] CHANNEL DESCRIPTION
1 Block 1 Red
2 Block 1 Green
3 Block 1 Blue
4 Block 1 White
5 Block 2 Red
6 Block 2 Green
7 Block 2 Blue
8 Block 2 White
9 Block 3 Red
10 Block 3 Green
11 Block 3 Blue
12 Block 3 White
13 Block 4 Red
14 Block 4 Green
15 Block 4 Blue
16 Block 4 White
[HSV] CHANNEL DESCRIPTION
1 Hue
2 Saturation
3 Value
COLORado™ Batten 80i User Manual 7 5/19/2008 10:40 AM

Product Overview
Power Link Out
DMX In 3+5-pin
DMX Out 3+5-pin
Power In
Bracket Adjustment
Hanging Bracket/ Floor Stand
Control Panel
Power In/Out
COLORado™ Batten 80i User Manual 8 5/19/2008 10:40 AM

3.SETUP
AC Power
This fixture has an auto-switching switch-mode power supply that can accommodate a wide range of
input voltages. The only thing necessary to do before powering on the unit is to make sure the line
voltage you are applying is within the range of accepted voltages. This fixture will accommodate
between 100V and 240V AC 50-60 Hz. All fixtures must be powered directly off a switched circuit and
cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch.
This fixture is designed for power linking from one COLORado™ Batten 80i to another COLORado™
Batten 80i fixture. Each fixture ships with Neutrik power input cables (standard Edison male-to-female
6ft A-type Neutrik 3-conductor connector).
Warning! All fixtures must be connected to circuits with a suitable Earth Ground.
Depending on the application, the lighting fixture may require a different connector. Please refer to
the below factory-installed Neutrik twist-lock terminator wire color code if installing a wire connector.
Wire Connection
Brown AC Live
Blue AC Neutral
Green/Yellow AC Ground
Connection Pin
AC Live 1
AC Neutral 2
Ground(Earth) 3
COLORado™ Batten 80i User Manual 9 5/19/2008 10:40 AM

Mounting
Orientation This fixture may be mounted in any safe position.
Rigging The fixture includes a mounting yoke to which a rigging clamp can be attached. You
must supply your own clamp and make sure the clamp is capable of supporting the
weight of this fixture. It is recommended to use at least 2 mounting points per
fixture. You can order “C” and “O”-clamps from any CHAUVET dealer or distributor
(CLP-15, CLP-06 recommended).
Note: There are 2 types of applications for this fixture: floor stand for up lighting, and
overhead use for down lighting. If you are using this fixture for up lighting, then you must
use 2 safety cables/chains for each fixture in addition to the mounting brackets.
If hanging the fixture for over head use, then please follow the below steps.
1. Block access below the work area and use suitable and stable platform
when installing or servicing fixture.
2. Safety cables must always be used. The safety cable must be capable of
holding 10 times the weight of the fixture.
3. Verify the structure can hold 10 times the weight of all to-be installed
fixtures.
4. This fixture may be mounting with clamps attached to the mounting bracket,
or attached directly to the fixture, as shown below.
Caution! After prolonged periods of operation, the fixture chassis may reach high
temperatures. This fixture must be mounted in a ventilated location, as it is
fan/convection cooled.
Hanging Clamp
Note: sold separately
Safety Cable (2)
For overhead
hanging purposes.
COLORado™ Batten 80i User Manual 10 5/19/2008 10:40 AM

Lens Assembly Installation/Replacement
The COLORado™Batten 80i comes with 15°lens assembly pre-installed from the factory. However, there are 3
other optional lens kits [CL18X10, CL18X15 (installed), CL18X30].available as accessories which will alter the beam
angle. Please follow the below instructions for proper replacement/installation.
1. Side plastic
1.
2.
2. Plastic LED cover 3. LENS ASSEMBLY
1. Remove 1 of the side, plastic covers (black), by removing the screws that hold it in place.
2. After removing the side plastic cover, slide out the plastic LED cover (clear).
3. Remove the screws that hold each of the 2 lens assemblies in place.
4. There are screws which hold the assembly together and which prevent the individual lenses
from moving. Remove these to gain access to them.
5. Arrange the new lens kit in the lens assembly (holder) and follow reverse steps to close the
fixture.
Warning! When replacing the lens assembly, please make sure that the power is
disconnected from the fixture beforehand.
COLORado™ Batten 80i User Manual 11 5/19/2008 10:40 AM

Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller
or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The
combined number of channels required by all the fixtures on a serial data link determines the number
of fixtures the data link can support.
Important: Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA-
485 standard no more than 32 devices should be connected on one data link. Connecting more
than 32 fixtures on one serialdata link without the use of a DMX optically-isolated splitter may
result in deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 meters (1640 ft.)
Maximum recommended number of fixtures on a serial data link: 32 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET-certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
DMX DATA CABLE
Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long distances. The cable will
have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor and shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms
CABLE CONNECTORS
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to r.
CO
MM
O
N
DMX
+
DMX -
INPUT OUTPUT
1
3
2
1
3
2
1
3
2
DMX connector configuration
Termination reduces signal errors. To
avoid signal transmission problems
and interference, it is always
advisable to connect a DMX signal
terminator.
Resistance 120
ohm 1/4w
between pin 2
(DMX -) and pin
3 (DMX +) of the
last fixture.
CAUTION Do not allow contact between the common and the fixture’s chassis ground. Grounding the common
verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each othe
COLORado™ Batten 80i User Manual 12 5/19/2008 10:40 AM

COLORado™ Batten 80i User Manual 13 5/19/2008 10:40 AM
This drawing provides a
general illustration of the
DMX Input/Output panel of
a lighting fixture.
U X Controllerniversal DM
Continue the link
-PIN TO 5-PIN CONVERSION CHART
X output connector, you willneed to use a 5 pin to 3 pin
adapter. CHAUVET Model No: DMX5M, or DMX5F.
3PIN TO 5PIN C
duc 3 Pin Female (output) 5 Pin Male (Input)
3
Note! If you use a controller with a 5 pin DM
The chart below details a proper cable conversion:
ONVERSION CHART
Con tor
Ground/Shield Pin 1 Pin 1
Data ( - ) signal Pin 2 Pin 2
Data ( + ) signal Pin 3 Pin 3
Do not use Do not use
Do not use Do not use
Setting up a DMX Serial Data Link
a (female) 3
t
ove to the input of the following
escription
.5m/14.8ft
1. Connect the (male) 3 pin connector side of
the DMX cable to the output (female) 3 pin
connector of the controller.
2. Connect the end of the cable coming from
the controller which will have
pin connector to the input connector of the
next fixture consisting of a (male) 3 pin
connector.
3. Then, proceed to connect from the outpu
as stated ab
fixture and so on.
CHAUVET Certified DMX Data Cables
Order Code D
DMX1.5 DMX Cable 1.5m/4.9ft
DMX4.5 DMX Cable 4
DMX10 DMX Cable 10m/32.8ft

4.OPERATING INSTRUCTIONS
Control Options
The COLORado™ Batten 80i is addressable in the DMX range of 001 to 512. In its simplest control
form, this allows for the control of 6 fixtures in the full pixel personality with 80 channels each;
however, a secondary “ID” address system exists for use in a limited DMX universe and
architectural environments. The “ID” address system allows the user to assign up to 66 fixtures
within the same DMX address. In effect, multiplying the control of COLORado’s™ within a single
universe to 396 fixtures. The COLORado’s™ “ID” address system is accessed using DMX channel
10 [Stage 1 & 2]. Consideration must be placed when programming live performances or cues that
need to trigger on demand or on a time line. So, to remain within one second execution time,
program no greater than 10 fixtures on ID addressing per DMX channel.
COLORado ™ Control Quick Setup
For detailed instructions on display panel operations and functions please advance to the section
titled; “Display Panel Functions”. These steps assume that you have read and are familiar with
setting up a DMX serial data link.
DMX-512 control without “ID” address
The COLORado™ Batten 80i operates on 10 channels of DMX (“STAGE1” personality). Address
each fixture in increments of 10 channels. (I.e. 1,11,22,33 etc…) To save time you can use the
same DMX address for each fixture. All fixtures will then respond simultaneously to control. You may
also group your fixtures and address those groups alike for faster programming and control.
2) 1. Access the control panel’s {DMX512 address} function by pressing the (UP/DOWN)
buttons until the function is displayed
3) 2. Press the (ENTER) button to enter panel function.
4) 3. Use the (UP/DOWN) buttons to increase or decrease channels between 001 and 512.
5) 4. Press the (ENTER) button to confirm action.
6) Deactivate ID addressing in each fixture by setting panel function {ID ON/OFF} to OFF.
{MENU} Â{Settings} Â{ID ON/OFF} Â[OFF]
Notes: If ID addressing is not deactivated in the fixture’s control panel function, unintended results
may occur if values are present in channel 10. Make sure values on channel 10 are set to “0”.
COLORado™ Batten 80i User Manual 14 5/19/2008 10:40 AM

DMX-512 addressing with ID address
1) Follow instructions 1 ~ 4 for DMX512 addressing.
2) Activate ID addressing in each fixture by setting panel function {ID ON/OFF} to ON.
{MENU} Â{Settings) Â{ID ON/OFF} Â[ON]
3) For every DMX512 starting address the user can set 66 separate ID addresses.
4) Set ID addresses in each fixture by setting panel function {ID address} to incremental values.
(I.e. 1,2,3,4,5,6,etc…)
{MENU} Â{Settings} Â{ID address} Â[01 ~ 66]
5) ID addresses are accessible using Channel 10 [Stage 1+2].
6)
D
MX Address: 001
I
D Address: 01 DMX Address: 013
I
D Address: 02
D
MX Address: 001
I
D Address: 02
D
MX Address: 001
I
D Address: 03 DMX Address: 013
I
D
A
ddress: 01 DMX Address: 013
I
D Address: 03
D
MX 512 Controlle
r
The figure above shows a simple DMX layout which has used three units at each
DMX address. The three units have different ID addresses which allows the user to
collectively control the whole group of units at that DMX address by setting Channel
10 to 0, or to control each unit independently by first selecting the DMX address and
then by using Channel 10 to locate the target ID address. (Note that when using ID
addresses it is also possible to activate ADAS which allows for even more option with
DMX addressing and control.
Setting the DMX address
Each fixture requires a "start address" from 1 to 512. A fixture requiring one or more channels for
control begins to read the data on the channel indicated by the start address. For example, a fixture
that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100, would
read data from channels: 100, 101, 102, 103, 104, 105 and 106. Choose start addresses so that the
channels used do not overlap and note the start address selected for future reference. The
COLORado™ 6 uses up to12 channels of DMX. If this is your first time using DMX, we recommend
reading the DMX Primer in the Appendix Section.
Control Panel Functions
All fixture functions and settings are accessible via the built in control panel interface.
MENU UP ENTER
DOWN
BUTTON FUNCTION
MENU Exits from the current menu or function
DOWN Navigates downwards through the menu list and decreases the numeric value when
in a function
UP Navigates upwards through the menu list and increases the numeric value when in
a function
ENTER Enables the currently displayed menu or sets the currently selected value in to the
selected function
COLORado™ Batten 80i User Manual 15 5/19/2008 10:40 AM

Manual Power ON/OFF
The COLORado™ Batten 80i can be turned on and off using the control panel. This can even be done when
there is no power connected to the fixture for setting the DMX address and any other functions that are useful
to do before the power in present. This is accomplished from the battery located internally in the fixture which
supplies enough power for the display to function.
•Note: this battery will not supply enough power for the fixture to operate the LED’s. This
is only to power the control board.
POWER ACTION
Turn ON Hold the {ENTER} button for 3 seconds to turn power on.
Turn OFF When the display in inactive for 20 seconds or more, the power will automatically turn off.
COLORado™ Batten 80i User Manual 16 5/19/2008 10:40 AM

Menu MapMAIN FUNCTION SUB-FUNCTION SELECTION INSTRUCTION
1. DMX Address 0-~512
•
Sets the DMX starting address
2. Personality
Block 1
•
16-channel mode
Block 2
•
16-channel mode
Block 3
•
16-channel mode
Block 4
•
16-channel mode
HSV
•
3-channel: hue, saturation, value
Stage 1
•
9-channel RGBW+D
Stage 2
•
12-channel RGBW+D
Arc 1
•
3-channel RGB
Arc 2
•
4-channel RGBW
Pixel 1
•
60-channel pixel mapping, no white
Pixel 2
•
80-channel pixel mapping, full
3. ID Address 0-66
•
Assigns the ID address to a fixture
4. Edit Static
Dimmer 000 ~ 255*
(0 ~ 100%)
*Strobe range is 0
~ 20
•User can combine Red, Green and
Blue to generate a custom color
•Select strobing frequency between 0
and 20Hz
Red
Green
Blue
Color Macros
Strobe
5. Auto Play Mode Auto (1~10)
•
Choose from 10 auto run programs
Personal (1~10)
•
Choose from 10 programs that be
customized under “edit custom”
6. Edit Custom Personal (1~10)
Red
•(0~255)
Green
Blue
White
Strob.
•
(0~20)
Timer
•
(0~255)
Fade
•
(0~255)
7. Settings
ID On~Off
•
Enables or disables ID ADAS
Dimmer Normal~Special
•
Sets the dimmer: linear or non-linear
Power Normal~High
•
Enables the power: normal or high
RGB to White Yes~No
•
Enables or disables RGB to White
Reset to default Password required
•
Reset to factory default setting
•Password: up+down+up+down
Reset to custom Password required
•
Reset custom values to 0
•Password: up+down+up+down
8. Key-Lock On~Off
•
Enables or Disables password lockout
9. White Calib
White (1~11)
Red •Sets Custom White Balance by
adjusting the maximum fader value
(0~255)
Green
Blue
White
RGB to White On ~ Off
•
This setting preset and switches RGB
to full power (Off) or RGB to white
(On)
10. Fan Setting
Off
•
Urns the fans completely off.
Quiet
•
Operates the fans in their quietest
operating speed
Low
•
Sets the fan speed to its low setting
Norm
•
Sets the fan speed to its median
operation
Fast
•
Sets the fan speed to its maximum
Auto
•
Automatically adjusts the fan speed,
11. Run Mode DMX Mode
•
Used for DMX controller compatibility
Slave mode
•
Used for master/slave operation
COLORado™ Batten 80i User Manual 17 5/19/2008 10:40 AM

DMX512 Channel Values
The COLORado™ Batten 80i has 13 DMX512 channel configurations [BLOCK1, BLOCK 2, BLOCK
3, BLOCK 4, HSV, ARC1+D, ARC2+D, STAGE 1, STAGE 2, ARC1, ARC2, PIXEL 1, and PIXEL 2].
STAGE 1 CHANNEL VALUE FUNCTION
1 000 Ù004
005 Ù255
Dimmer
No Function
0 Ù100%
2 000 Ù004
005 Ù255
Red
No Function
0 Ù100%
3 000 Ù004
005 Ù255
Green
No Function
0 Ù100%
4 000 Ù004
005 Ù255
Blue
No Function
0 Ù100%
5 000 Ù004
005 Ù255
White
No Function
0 Ù100%
6
000 Ù005
006 Ù020
021 Ù035
036 Ù050
051 Ù065
066 Ù080
081 Ù095
096 Ù110
111 Ù125
126 Ù130
131 Ù135
136 Ù140
141 Ù145
146 Ù150
151 Ù155
156 Ù160
161 Ù165
166 Ù170
171 Ù175
176 Ù180
181 Ù185
186 Ù190
191 Ù200
201 Ù205
206 Ù210
211 Ù215
216 Ù220
221 Ù225
226 Ù230
231 Ù235
236 Ù240
241 Ù245
246 Ù250
251 Ù255
Color Macro
No Function
Red 100%/ Green Up/ Blue 0%
Red Down/ Green 100%/ Blue 0%
Red 0%/ Green 100%/ Blue Up
Red 0%/ Green Down/ Blue 100%
Red Up/ Green 0%/ Blue 100%
Red 100%/ Green 0%/ Blue Down
Red 100%/Green Up/Blue Up
Red Down/Green Down/Blue 100%
Red 100%
Red 70%/ White 30%
Red 50%/ White 50%
Red 30%/ White 70%
White 100%
Green 30%/ White 70%
Green 50%/ White 50%
Green 70%/ White 50%
Green 100%
Blue 100%
Blue 70%/ White 30%
Blue 50%/ White 50%
Blue 30%/ White 70%
RGBW 100%
White 1:3200K
White 2: 3400K
White 3: 4200K
White 4: 4900K
White 5: 5600K
White 6: 5900K
White 7: 6500K
White 8: 7200K
White 9: 8000K
White 10: 8500K
White 11: 10000K
7 000 Ù004
005 Ù255
Strobe
No Function
0 Ù20Hz
COLORado™ Batten 80i User Manual 18 5/19/2008 10:40 AM

8
000 Ù010
011 Ù020
021 Ù030
031 Ù040
041 Ù050
051 Ù060
061 Ù070
071 Ù080
081 Ù090
091 Ù100
101 Ù110
111 Ù120
121 Ù130
131 Ù140
141 Ù150
151 Ù160
161 Ù170
171 Ù180
181 Ù190
191 Ù200
201 Ù210
211 Ù220
221 Ù230
231 Ù240
241 Ù250
251 Ù255
Auto + Custom + Fan control
No Function
Fans Off (Hold for 3 sec.)
Fans Low (Hold for 3 sec.)
Fans Normal (Hold for 3 sec.)
Fans High (Hold for 3 sec.)
Fans Auto (Hold for 3 sec.)
Auto 1
Auto 2
Auto 3
Auto 4
Auto 5
Auto 6
Auto 7
Auto 8
Auto 9
Auto 10
Custom 1
Custom 2
Custom 3
Custom 4
Custom 5
Custom 6
Custom 7
Custom 8
Custom 9
Custom 10
9 001 Ù255 Auto Speed
CHANNEL 10 (ID ADDRESS SELECTION)
000 Ù009
010 Ù019
020 Ù029
030 Ù039
040 Ù049
050 Ù059
060 Ù069
070 Ù079
080 Ù089
090 Ù099
100 Ù109
110 Ù119
120 Ù129
130 Ù139
140 Ù149
150 Ù159
160 Ù169
170 Ù179
180 Ù189
190 Ù199
200 Ù209
210
211
All IDs
ID 1
ID 2
ID 3
ID 4
ID 5
ID 6
ID 7
ID 8
ID 9
ID 10
ID 11
ID 12
ID 13
ID 14
ID 15
ID 16
ID 17
ID 18
ID 19
ID 20
ID 21
ID 22
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
ID 23
ID 24
ID 25
ID 26
ID 27
ID 28
ID 29
ID 30
ID 31
ID 32
ID 33
ID 34
ID 35
ID 36
ID 37
ID 38
ID 39
ID 40
ID 41
ID 42
ID 43
ID 44
ID 45
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
ID 46
ID 47
ID 48
ID 49
ID 50
ID 51
ID 52
ID 53
ID 54
ID 55
ID 56
ID 57
ID 58
ID 59
ID 60
ID 61
ID 62
ID 63
ID 64
ID 65
ID 66
COLORado™ Batten 80i User Manual 19 5/19/2008 10:40 AM

STAGE 2
CHANNEL VALUE FUNCTION
1
000 Ù255 Dimmer 0 Ù100%
2
000 Ù255 Red 0 Ù100%
3
000 Ù255 Green 0 Ù100%
4
000 Ù255 Blue 0 Ù100%
5
000 Ù255 White 0 Ù100%
6
000 Ù005
006 Ù020
021 Ù030
031 Ù050
051 Ù070
071 Ù090
091 Ù110
111 Ù130
131 Ù150
151 Ù170
171 Ù190
191 Ù200
201 Ù205
206 Ù210
211 Ù215
216 Ù220
221 Ù225
226 Ù230
231 Ù235
236 Ù240
241 Ù245
246 Ù250
251 Ù255
Color Macros
No Function
Hyper Color™ (Only when in Normal Power Mode)
No Function
Red 100%/ Green Up/ Blue 0%
Red Down/ Green 100%/ Blue 0%
Red 0%/ Green 100%/ Blue Up
Red 0%/ Green Down/ Blue 100%
Red Up/ Green 0%/ Blue 100%
Red 100%/ Green 0%/ Blue Down
Red 100%/ Green Up/ Blue Up
Red Down/ Green Down/ Blue 100%
RGBW 100%
White 1:3200K
White 2: 3400K
White 3: 4200K
White 4: 4900K
White 5: 5600K
White 6: 5900K
White 7: 6500K
White 8: 7200K
White 9: 8000K
White 10: 8500K
White 11: 10000K
7 000 Ù004
005 Ù255
Strobe
No Function
0 Ù20Hz
8
000 Ù010
011 Ù020
021 Ù030
031 Ù040
041 Ù050
051 Ù060
061 Ù070
071 Ù080
081 Ù090
091 Ù100
101 Ù110
111 Ù120
121 Ù130
131 Ù140
141 Ù150
151 Ù160
161 Ù170
171 Ù180
181 Ù190
191 Ù200
201 Ù210
211 Ù220
221 Ù230
231 Ù240
241 Ù250
251 Ù255
Auto + Custom + Fan control
No Function
Fans Off (Hold for 3 sec.)
Fans Low (Hold for 3 sec.)
Fans Normal (Hold for 3 sec.)
Fans High (Hold for 3 sec.)
Fans Auto (Hold for 3 sec.)
Auto 1
Auto 2
Auto 3
Auto 4
Auto 5
Auto 6
Auto 7
Auto 8
Auto 9
Auto 10
Custom 1
Custom 2
Custom 3
Custom 4
Custom 5
Custom 6
Custom 7
Custom 8
Custom 9
Custom 10
COLORado™ Batten 80i User Manual 20 5/19/2008 10:40 AM