Chauvet Q-Spot 575 User manual

CHAUVET, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A
[phone] –[phone]
FAX [phone]
www.chauvetlighting.com
2006-05-17/13:25
Q-Spot™575
USER MANUAL

Q-Spot 575 User Manual 2 2006-05-17/13:25
Table of Content
BEFORE YOU BEGIN....................................................................................................................................................... 3
WHAT IS INCLUDED .......................................................................................................................................................................................................... 3
UNPACKING INSTRUCTIONS.............................................................................................................................................................................................. 3
AC POWER ..................................................................................................................................................................................................................... 3
SAFETY INSTRUCTIONS.................................................................................................................................................................................................... 3
INTRODUCTION............................................................................................................................................................... 4
TECHNICAL FEATURES..................................................................................................................................................................................................... 4
FEATURES....................................................................................................................................................................................................................... 4
DMX CHANNEL SUMMARY ............................................................................................................................................................................................... 4
PRODUCT OVERVIEW....................................................................................................................................................................................................... 5
SETUP .............................................................................................................................................................................. 6
LAMP............................................................................................................................................................................................................................. 6
Maximizing the life of your lamp......................................................................................................................................................................... 6
Lamp Installation ................................................................................................................................................................................................ 6
POWER ........................................................................................................................................................................................................................... 7
EXCHANGING GOBOS ....................................................................................................................................................................................................... 7
MOUNTING ...................................................................................................................................................................................................................... 7
MOUNTING ...................................................................................................................................................................................................................... 8
OPERATING INSTRUCTIONS.......................................................................................................................................... 9
CONTROL PANEL ............................................................................................................................................................................................................. 9
CONTROL PANEL FUNCTIONS........................................................................................................................................................................................... 9
APPLYING CHANGES TO FUNCTIONS (QUICK INSTRUCTIONS) ............................................................................................................................................ 9
OPERATING MODES....................................................................................................................................................................................................... 10
Master/Stand Alone.......................................................................................................................................................................................... 10
Setting Slave Fixtures ......................................................................................................................................................................................10
DMX Mode........................................................................................................................................................................................................ 10
Daisy Chain Connection................................................................................................................................................................................... 10
DMX-512 addressing ............................................................................................................................................................................................. 11
Setting the starting address .............................................................................................................................................................................11
User Configurations ............................................................................................................................................................................................... 11
Pan Invert & Tilt Invert...................................................................................................................................................................................... 11
Color Wheel (split colors) ................................................................................................................................................................................. 11
Service Functions .................................................................................................................................................................................................. 11
Fixture Reset (all motors)................................................................................................................................................................................. 11
APPENDIX...................................................................................................................................................................... 12
DMX PRIMER ................................................................................................................................................................................................................ 12
Fixture Linking .................................................................................................................................................................................................. 12
DMX VALUES................................................................................................................................................................................................................ 13
MAINTENANCE............................................................................................................................................................................................................... 15
RETURNS PROCEDURE .................................................................................................................................................................................................. 15
CLAIMS ......................................................................................................................................................................................................................... 15
GOBO IMAGES ............................................................................................................................................................................................................... 15
GENERAL TROUBLESHOOTING ....................................................................................................................................................................................... 16
TECHNICAL SPECIFICATIONS .......................................................................................................................................................................................... 17
TECHNICAL SUPPORT .................................................................................................................................................................................................... 17

Q-Spot 575 User Manual 3 2006-05-17/13:25
100V
100V
115V
115V
208V
208V
230V
230V
240V
240V
50Hz
50Hz60HzININ
60Hz
Select voltage
To Ballast 230V/50Hz
To Ballast 230V/60Hz
Lamp Control to PCB in
AC-100-230V
INPUT
To TRANSFORME R
BEFORE YOU BEGIN
What is included
Q-Spot™575
5 extra gobos
Power cord with plug
HMI-575 Discharge lamp
Manual
Warranty Card
230V fuse
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
AC Power
To determine the power requirements for a particular fixture, see the label affixed to the back plate of
the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average
current draw under normal conditions. All fixtures must be
powered directly off a switched circuit and cannot be run
off a rheostat (variable resistor) or dimmer circuit, even if
the rheostat or dimmer channel is used solely for a 0% to
100% switch. Before applying power to a fixture, check
that the source voltage matches the fixture’s requirement.
Check the fixture or device carefully to make sure that if a
voltage selection switch exists that it is set to the correct
line voltage you will use.
Warning! Verify that the internal multi-tap transformer is
set to match the line voltage applied. All
fixtures must be connected to circuits with a
suitable Earth Ground.
Safety Instructions
Please keep this User Guide for future consultation. If you
sell the unit to another user, be sure that they also receive
this instruction booklet.
Always make sure that you are connecting to the proper
voltage and that the line voltage you are connecting to is
not higher than that stated on decal or rear panel of the
fixture.
This product is intended for indoor use only!
To prevent risk of fire or shock, do not expose fixture to
rain or moisture. Make sure there are no flammable
materials close to the unit while operating.
The unit must be installed in a location with adequate
ventilation, at least 50cm (20in) from adjacent surfaces.
Be sure that no ventilation slots are blocked.
Always disconnect from power source before servicing or
replacing lamp or fuse and be sure to replace with same
lamp source.
Secure fixture to fastening device using a safety chain.
Never carry the fixture solely by its head. Use its carrying
handles.
Maximum ambient temperature is Ta: 40°. Do not operate
fixture at temperatures higher than this.
In the event of serious operating problem, stop using the
unit immediately. Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest
authorized technical assistance center. Always use the
same type spare parts.
Don’t connect the device to a dimmer pack.
Make sure power cord is never crimped or damaged.
Never disconnect power cord by pulling or tugging on the
cord.
Avoid direct eye exposure to lamp while it is on.
Caution! There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET.
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance?

Q-Spot 575 User Manual 4 2006-05-17/13:25
INTRODUCTION
Technical Features
16 channel DMX-512 moving yoke
Pan: 540° / Tilt: 280°
- 16 bit movement resolution
- 21° beam angle
Pan/Tilt speed channel
Lamp ON/OFF
Remote fixture reset
Color wheel
- 8 colors + white
- 1 split color & 1 quad-color
- Rainbow color spin in both directions at variable speeds
- Linear color wheel movement for color splits
3-facet high speed rotating prism
- Rotating prism in both directions at variable speeds
Static gobo wheel
- 9 interchangeable gobos + open
- Gobo wheel spin in both directions at variable speeds
Rotating gobos
- 6 interchangeable rotating plus open
- 3 metal, 3 dichroic installed
- Additional gobos: 1 dichroic & 4 metal
- Rotating gobo wheel spin in both directions at variable speeds
Motorized focus
Variable strobe/shutter
Mechanical dimmer (0~100%)
Features
Automatic Pan & Tilt correction
Micro-stepping motors
LED display
Display auto off
Thermal switch
Fan cooled
Removable air filter
DMX Channel Summary
CHANNEL FUNCTION CHANNEL FUNCTION
1 Pan 9 Prism Rotation
2 Tilt 10 Static Gobos
3 Pan (Fine) 16 bit 11 Rotating Gobos
4 Tilt (Fine) 16 bit 12 Gobo Rotation
5 Pan/Tilt Speed 13 No Function
6 Lamp on/off & reset 14 Motorized Focus
7 Colors 15 Shutter/Strobe
8 Prism 16 Dimmer

Q-Spot 575 User Manual 5 2006-05-17/13:25
Product Overview
SEGMENT BUTTONS I/O PANEL OVERVIEW
BUTTONS I/O PANEL
MODE Toggles programming
functions DMX Out & In DMX-512 connectors
DOWN Steps backward through menu
functions Power AC input IEC 60320 C14 and fuse holder
UP Steps forward through menu
functions
ENTER Confirms selected menu
function
1 1. Moving yoke arm
2. Projector head
3. Base
4. Carrying handle
5. Fan
7. LED display
8. [Enter] button
9. [Choose] button
10. [Up] button
11. [Down] button
12. DMX output
13. DMX input
14. Carrying handle
15. AC input IEC socket
16. Fuse holder
17. Power switch
2
3
4
5
12 13
14
1516
17
7
8 9 10 11
DMX Signal Indicator

Q-Spot 575 User Manual 6 2006-05-17/13:25
1
S
1
1
2
2
S3
3,4
5
N
Always
replace Lamp
cover and Top
cover before
re-igniting
lamp!
Please use a flat-head screw
driver to loosen and tighten
(S2) thumbscrews securely!
S
2
SETUP
LAMP
Maximizing the life of your lamp
To ensure the longest and most efficient use of the lamp always wait
between 10 and 15 minutes before re-applying power after a shutdown.
Failure to do so could result in premature aging of the lamp and failure to
the electronics that drive it.
You will need to install a lamp prior to the initial operation of the fixture. A HMI575 high intensity
discharge lamp is included. Do not touch the envelope (glass area) of the bulb with bare hands. If this
happens, clean the lamp with alcohol and wipe it with a lint free cloth before installation.
Lamp Installation
1. Unscrew (S1) to detach the top cover.
2. Unscrew (S2) to remove
lamp cover and expose
lamp compartment.
3. If installing a new lamp,
loosen both screws on
the double ended lamp
to allow for the lamp to
slide into the lamp
socket slots. Lower lamp evenly.
4. If replacing a lamp, loosen both lamp
screws (S3) to relieve tension from
lamp socket slots so you can slide the
lamp freely, upwards and out of lamp
socket. Raise lamp evenly to remove.
5. Before you tighten the lamp end screws, rotate the
bulb until the nipple on the envelope (N) of the bulb is
facing upwards as illustrated.
6. DO NOT OPERATE UNIT WITHOUT LAMP AND
FIXTURE COVERS SECURELY REPLACED!

Q-Spot 575 User Manual 7 2006-05-17/13:25
100V
100V
115V
115V
208V
208V
230V
230V
240V
240V
50Hz
50Hz60HzININ
60Hz
Select voltage
To Ballast 230V/50Hz
To Ballast 230V/60Hz
Lamp Control to PCB in
AC-100-230V
INPUT
To TRANSFORMER
Power
Warning! Verify that the internal multi-tap transformer is set to match the line voltage applied
and that the proper fuse is installed for the appropriate voltage setting. All fixtures
must be connected to circuits with a suitable Earth Ground.
To determine the power requirements for
a particular fixture, see the label affixed
to the back plate of the fixture or refer to
the fixture’s specifications chart.
A fixture’s listed current rating is its
average current draw under normal
conditions.
All fixtures must be powered directly off a
switched circuit and cannot be run off a
rheostat (variable resistor) or dimmer
circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100%
switch.
Before applying power to a fixture, check
that the source voltage matches the
fixture’s requirement.
All fixtures must be connected to circuits with a suitable Earth Ground.
POWER CABLE PIN INTERNATIONAL
BROWN Live L
BLUE Neutral N
YELLOW/GREEN Earth EG (Ground)
OPERATING VOLTAGE MUST USE CORRECT FUSE
120V 15A
230V 6.3A
Exchanging gobos
1. Press both tips of the gobo tension ring together and remove from aperture.
2. Push the gobo with your finger from the back side following the same direction that the tension
ring was removed.
Gobo outside diameter: 31 mm
Gobo Image diameter: 22.5 mm
Rotating gobo max thickness: 3 mm
Static gobo max thickness: 2mm
Extra Gobos for the Q-Spot™575
Q-Spot™575 Gobo Wheel
CAUTION!
This lighting
fixture comes
from the
factory with a
120V fuse pre-
installed. To
operate this
fixture in 230V,
please replace
the external
fuse with the
supplied 230V
fuse.

Before You Begin
Q-Spot 575 User Manual 8 2006-05-17/13:25
Mounting
Orientation
The Q-Spot™575 can sit on stage or be mounted on a truss using a clamp in any position, provided,
there is adequate room for ventilation.
Warning
It is important never to obstruct the fan or vents pathway.
The installation of the projector has to be built and constructed in a way that it can hold 10 times
the weight for 1 hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g. an appropriate
catch net. This secondary safety attachment must be constructed in a way that no part of the
installation can fall down if the main attachment fails.
When rigging, de-rigging or servicing the fixture staying in the area below the installation place, on
bridges, under high working places and other endangered areas is forbidden.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not
limited to) calculating working load limits, installation material being used, and periodic safety
inspection of all installation material and the projector. If you lack these qualifications, do not
attempt the installation yourself, but instead use a professional structural rigger. Improper
installation can result in bodily injury and or damage to property.
The projector should be installed out of the reach of people.
When selecting installation location, take into consideration lamp replacement access and routine
maintenance.
Safety cables should always be used.
Never mount in places where the fixture will be exposed to rain, high humidity, extreme
temperature changes or restricted ventilation.
The fixture must have a minimum of 1 meter from combustible materials.
Rigging
The Q-Spot™575 includes 3 mounting bracket to which rigging clamps can be bolted.
1. Verify the structure can hold 10 times the weight of all to-be installed fixtures.
2. From a stable platform, attach two clamps as illustrated on drawing above.
1. Clamp
2. Mounting plate
3. Brackets
1
2
3
S
afety Cable
& Clamp sold
separately!
Mounting Bracket
A MINIMUM
OF TWO
MOUNTING
POINTS
MUST BE
USED!

Q-Spot 575 User Manual 9 2006-05-17/13:25
OPERATING INSTRUCTIONS
Control Panel
Please be aware that after 12 seconds of no control panel activity the LEDs in the display will turn off.
Press any button to initialize.
On the control panel you can set the DMX address, set the fixture to Master/Slave mode, reset the
fixture and change fixture personality trait.
Control Panel Functions
FUNCTION OPTIONS NOTES
PAN NO/YES Pan Invert
Tilt NO/YES Tilt Invert
Addr A001 DMX Channel Address
rESt YES Fixture reset
COLI NO/YES Linear progression of color wheel (split colors)
RUN
dn.Co.
Pr6.1
Pr6.2
SLAE
Sou.1
Sou.2
DMX-512 Mode
Automatic Program 1 (when mounted upside down)
Automatic Program 2 (when floor positioned)
Slave Mode
Music Program 1 (when mounted upside down)
Music Program 2 (when floor positioned)
LAMP ON
OFF
Lamp on
Lamp off
VEr 1.X Software version
HEAt Status Too hot to strike or no lamp
LA.Er Status Lamp error
Applying changes to Functions (Quick Instructions)
Unless other wise stated changes in the control panel can be applied in the following manner.
1. Press [MODE] button repeatedly until the display reads the menu function you wish to change as
illustrated in the table above in section “Control Panel Functions”
2. Press the [ENTER] key to confirm the selection
3. Press the [Up] or [Down] button to toggle between the options available for that particular menu
function.
4. Press the [Enter] button to store your selection.
[MODE] Confirms selection
[ENTER] Access to main menu
[Up] Toggle menu items in a forward direction
[Down] Toggle menu items in a reverse direction

Q-Spot 575 User Manual 10 2006-05-17/13:25
Daisy Chain
Connection
Terminator
sold separately
Operating Modes
A stand-alone mode will listen to sound and run through its diverse range of built in programs.
Master/Slave mode will allow the command of up to as many units you want in a synchronized
light show to the sound.
DMX control mode will provide the greatest flexibility and creativity. Each fixture trait can be
controlled individually using any universal DMX-512 controller.
Master/Stand Alone
Two options are available, a sound-active mode or an automatic mode. In sound-active mode the
internal programs are triggered by the beat of the sound. In automatic mode the internal programs run
at the chase time pre-recorded. It is your choice to enable each fixture to run in Stand Alone mode by
activating either of the two functions below or to proceed to enable slave fixtures as described in the
following section.
MENU SET TONOTES
RUN
Pr6.1
Sou.1
Pr6.2
Sou.2
Auto 1 (use when fixture is flown and hangs upside down)
Music 1 (use when fixture is flown and hangs upside down)
Auto 2 (use when fixture is floor positioned)
Music 2 (use when fixture is floor positioned)
Setting Slave Fixtures
The Master/Slave mode will allow you to link multiple units in a daisy chain fashion. In this mode, the
first unit in the daisy chain, the master, will automatically command all other units following. The first
unit will operate in a Stand/Alone mode and all units following will synchronize to the first unit.
MENU SET TONOTES
RUN SLAE Slave mode
You can Invert the Pan and Tilt settings freely.
DMX Mode
Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to
customizing or creating a show. You can tailor your programming to suit a specific event. Whether it
is a wedding where a spot light may be required or a lead singer requiring a color solo, the
opportunities are endless. In this mode you will be able to control each individual trait of the fixture
independently.
MENU SET TONOTES
RUN dn.Co. DMX-512 mode
Daisy Chain Connection
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector
of the first fixture.
2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin
connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,
proceed to connect from the output as stated above to the input of the following fixture and so on.

Operating Instructions
Q-Spot 575 User Manual 11 2006-05-17/13:25
DMX-512 addressing
This mode enables the use of a universal DMX controller device. Each fixture requires a "start
address" from 1 to 511. A fixture requiring one or more channels for control begins to read the data
on the channel indicated by the start address. For example, a fixture that occupies or uses 6 channels
of DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101,
102, 103, 104, and 105. Choose start addresses so that the channels used do not overlap and notate
the start address selected for future reference.
If this is your first time addressing a fixture using the DMX-512 control protocol than I suggest jumping
to the Appendix Section and read the heading “DMX Primer”. It contains very useful information that
will help you understand its use.
Setting the starting address
1. Press the [MENU] button until the display reads “Addr”.
2. Press the [ENTER] button confirm selection.
3. Press the [Up] and [Down] buttons to increase or decrease values until the desired value is
achieved.
4. Press the [Enter] button to activate selection.
User Configurations
Pan Invert & Tilt Invert
It is possible to invert the pan and tilt head movement from within the fixture itself. This could be
helpful in situations where the positioning or rigging of a fixture led to a reverse orientation of the
fixture in relation to all or most other fixtures installed. When choosing to command the pan or tilt of
all fixtures at the same time you will notice that the fixtures whose orientation is different from the
others will most likely move opposite of the rest. You can apply a pan and tilt Invert by following the
settings in the table below.
FUNCTION SET TONOTES
PAN YES Pan Invert
tiLt YES Tilt Invert
Color Wheel (split colors)
Linear progression or advancement of the color wheel will enable you to stop anywhere in between
two adjacent colors.
FUNCTION SET TONOTES
COLI YES With linear progression or advancement of the
color wheel split colors will be achieved.
Service Functions
Fixture Reset (all motors)
This function will re-initialize the fixture by returning all motors to its startup positions or otherwise
known as (home position).
FUNCTION SET TONOTES
rESt [ENTER] Reset fixture

Q-Spot 575 User Manual 12 2006-05-17/13:25
APPENDIX
DMX Primer
There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A
fixture capable of receiving DMX-512 will require one or a number of sequential channels. The user
must assign a starting address on the fixture that indicates the first channel reserved in the controller.
There are many different types of DMX controllable fixtures and they all may vary in the total number
of channels required. Choosing a start address should be planned in advance. Channels should
never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is
set incorrectly. You can however, control multiple fixtures of the same type using the same starting
address as long as the intended result is that of unison movement or operation. In other words, the
fixtures will be slaved together and all respond exactly the same.
DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which
the fixtures are connected is not important and has no effect on how a controller communicates to
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET
carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)
Fixture Linking
Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5
pin to 3 pin adapter. CHAUVET Model No: DMX5M.
The chart below details a proper cable conversion:
3PIN TO 5PIN CONVERSION CHART
Conductor 3 Pin Female (output) 5 Pin Male (Input)
Ground/Shield Pin 1 Pin 1
Data ( - )signal Pin 2 Pin 2
Data ( + ) signal Pin 3 Pin 3
Do not use Do not use
Do not use Do not use
COMMON
DMX +
DMX
-
INPUT OUTPUT
1
3
2
1
3
2
1
3
2
Resistance 120
ohm 1/4w between
pin 2 (DMX -) and
pin 3 (DMX +) of
the last fixture.
Termination reduces signal errors and to
avoid signal transmission problems and
interference, it is always advisable to
connect a DMX signal terminator.
Figure 1 - DMX connector configuration

Appendix
Q-Spot 575 User Manual 13 2006-05-17/13:25
DMX Values
CHANNEL VALUE FUNCTION
1
000 255 Pan Left > Right ( 128 = center)
2
000 255 Tilt Up > Down (128 = center)
3 000 255 Pan (Fine) 16 bit
4 000 255 Tilt (Fine) 16 bit
5
000 255 Pan/Tilt Speed Fast > Slow
6
000 127
128 139
140 229
230 239
240 255
Lamp on/off & Reset
No Function
Lamp on after 3 seconds when lamp is off
Fixture reset when lamp is on
No Function
Lamp off after 3 seconds
No Function
7
000
006
012
018
024
030
036
042
048
053
059
065
071
076
082
088
094
100
106
111
117
122
128 255
Color Wheel (Linear)
White (Open)
White/Blue
Blue
Blue/Orange
Orange
Orange/Quad
Yellow/Green/Sky Blue/Orange
Quad/UV
UV
UV/Rose-Red
Rose-Red
Rose-Red/Red
Red
Red/Orange-Sky Blue
Orange-Sky Blue
Orange-Sky Blue/Yellow
Yellow
Yellow/Pink
Pink
Pink/Green
Green
Green/White
Rainbow effect: Fast > Slow
(clockwise)
000 007
008 019
020 031
032 043
044 055
056 067
068 079
080 091
092 103
104 115
116 127
128 255
Color Wheel (Step)
White (Open)
Blue
Orange
Quad Color
UV
Rose-Red
Red
Orange-Sky Blue
Yellow
Pink
Green
Rainbow effect: Fast > Slow
(clockwise)
8
000 127
128 255
Prism
No Function
3-facet prism
9
000 004
005 127
128 132
133 255
Prism Rotation
No rotation
Clockwise rotation: Fast > Slow
No rotation
Counter-clockwise rotation: Slow > Fast
Continued on the next page…

Q-Spot 575 User Manual 14 2006-05-17/13:25
CHANNEL VALUE FUNCTION
10
000 009
010 019
020 029
030 039
040 049
050 059
060 069
070 079
080 089
090 099
100 109
110 119
120 129
130 139
140 149
150 159
160 169
170 179
180 189
190 199
200 255
Static Gobos
Open/White
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 8
Gobo 9
Open
Gobo Bounce: Gobo 1 (Slow > Fast)
Gobo Bounce: Gobo 2 (Slow > Fast)
Gobo Bounce: Gobo 3 (Slow > Fast)
Gobo Bounce: Gobo 4 (Slow > Fast)
Gobo Bounce: Gobo 5 (Slow > Fast)
Gobo Bounce: Gobo 6 (Slow > Fast)
Gobo Bounce: Gobo 7 (Slow > Fast)
Gobo Bounce: Gobo 8 (Slow > Fast)
Gobo Bounce: Gobo 9 (Slow > Fast)
Gobo Scroll: Slow > Fast
11
000 029
030 059
060 089
090 119
120 149
150 179
180 209
210 255
Rotating Gobo
Open/White
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo Scroll: Slow > Fast
12
000 060
061 158
159 255
Gobo Rotation
Gobo progressive rotation (0 ~ 540°)
Clockwise rotation: Slow > Fast
Counter-clockwise rotation: Slow > Fast
13 No Function
14
000 225 Focus Far > Near
15
000 031
032 063
064 095
096 127
128 159
160 191
192 223
224 255
Shutter/Strobe
Closed
Open
Strobe: Slow > Fast (max 10fps)
Open
Pulse: Slow > Fast
Open
Random: Slow > Fast
Open
16
000 225 Dimmer Intensity: 0 ~ 100%

Appendix
Q-Spot 575 User Manual 15 2006-05-17/13:25
Maintenance
To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.
Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust
collected on external vents and internal components. Clean all glass when the fixture is cold with a
mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply
solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical
surfaces until they are free of haze and lint. Do not to touch the lamp glass when cleaning fixture. Oil
and dirt can cause damage and premature aging of the lamp. In the event that the lamp is touched or
becomes dirty, clean the lamps with an alcohol wipe.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s
optics. Clean with soft cloth using normal glass cleaning fluid. - Always dry the parts carefully. - Clean
the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products
returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause
for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate
packaging is the customer’s responsibility. CHAUVET reserves the right to use its own discretion to
repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe
method to use.
Claims Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.
Gobo Images
Rotating Gobos Static Gobos

Appendix
Q-Spot 575 User Manual 16 2006-05-17/13:25
General Troubleshooting
Applies to
Symptom Solution(s) Lights
Foggers
& Snow Controllers
Dimmers
& Chaser
Auto shut off Check fan thermal switch reset 
Beam is very dim or not
bright Clean optical system or replace lamp Check 220/110v switch for proper setting 
Breaker/Fuse keeps
blowing Check total load placed on device 
Chase is too slow Check users manual for speed adjustment 
Device has no power Check for power on Mains.
Check device’s fuse. (internal and/or external) 
Fixture is not responding Check DMX Dip switch settings for correct addressing
Check DMX cables
Check polarity switch settings

Fixture is on but there is
no movement to the
audio
Make sure you have the correct audio mode on the control
switches. If audio provided via ¼”jack, make sure a live audio
signal exists
Adjust sound sensitivity knob
 
Lamps cuts off
sporadically Possible bad lamp or fixture is overheating. Lamp may be at end of its life. 
Light will not come on
after power failure Some discharge lamps require a cooling off period before the electronics in the fixture can kick start it again, wait 5 to 10
minutes before powering up

Loss of signal Use only DMX cables
Install terminator
Note: Keep DMX cables separated from power cables or black
lights.

Motor movements are
jerky or jumpy Possible bad motor driver or sensors Check polarity switch on controller 
Moves slow Check 220/110v switch for proper setting 
No flash Re-install bulb, may have shifted in shipping 
No light output Check slip ring & brushes for contact
Install bulb
Call service technician

Relay will not work Check reset switch
Check cable connections 
Remote does not work Make sure connector is firmly connected to device 
Stand alone mode All CHAUVET lighting fixtures featuring stand-alone functions
do not require additional settings, simply power the fixture and
it will automatically enter into this mode

Unit wobbles when
rotating Check for damages possibly incurred during shipping 

Appendix
Q-Spot 575 User Manual 17 2006-05-17/13:25
Technical Specifications
WEIGHT & DIMENSIONS
Length........................................................................................................................404 mm (15.9 in)
Width..........................................................................................................................348 mm (13.7 in)
Height ........................................................................................................................529 mm (25.4 in)
Weight........................................................................................................................33.6 Kgs (74 lbs)
POWER
Internal multi-tap transformer .................................................100V, 115V, 208V, 230V, 50 Hz or 60Hz
AC input...........................................................................................................................3 prongs IEC
European version...............................................................................................................240V 50 Hz
Current draw.............................................................(inrush 1133W @ 120V), (peak 1326W @ 120V)
Current draw.............................................................(inrush 1050W @ 230V), (peak 1978W @ 230V)
LAMPS
Osram™HMI575/GS....................................................................................... 1000 hr, 6000K, 575W
PHOTO OPTIC
Beam Angle ....................................................................................................................................21°
Pan............................................................................................................................................... 540°
Tilt................................................................................................................................................. 280°
GOBOS
Outside diameter........................................................................................................................31 mm
Image diameter.......................................................................................................................22.5 mm
Maximum thickness......................................................................................................................3 mm
Static gobo max thickness............................................................................................................2 mm
THERMAL
Maximum ambient temperature......................................................................................... 45° (113° F)
FUSE
Main (115V) ..............................................................................................20mm Glass 15A Fast Blow
Main (230V) .............................................................................................20mm Glass 6.3A Fast Blow
CONTROL & PROGRAMMING
Data input .............................................................................................locking 3-pin XLR male socket
Data output........................................................................................ locking 3-pin XLR female socket
Data pin configuration ............................................................................pin 1 shield, pin 2 (-), pin 3 (+)
Protocols.....................................................................................................................DMX-512 USITT
DMX Channels (Q-SPOT575)...........................................................................................................16
ORDERING INFORMATION
Q-Spot™575 ....................................................................................................................Q-SPOT575
Fuse 15A ......................................................................................................................P170FUSE015
Fuse 10A ......................................................................................................................P170FUSE010
Technical Support
Address: Service Dept.
3000 N 29th Ct, Hollywood, FL 33020 (U.S.A.)
Support (Email): [e-mail]
Telephone: [phone] - (Press 4)
Fax: [phone] - (Attention: Service)
Website:...............................................................................................http://www.chauvetlighting.com