Chauvet Q-Wash 419Z-LED User manual

Quick Reference Guide
English EN
Español ES
Français FR

Q-Wash™ 419Z-LED QRG EN
2
About this
Guide
The Q-Wash™ 419Z-LED Quick Reference Guide (QRG) has basic
product information such as connection, mounting, menu options,
and DMX values.
For more information on the product, download the user manual at
www.chauvetpro.com .
Disclaimer
The information and specifications contained in this QRG are subject
to change without notice.
Safety Notes
•Do not open this product. It contains no user-serviceable parts.
•Do not look at the light source when the product is on.
•Caution: This product’s housing may be hot when lights are
operating.
•Mount this product in a location with adequate ventilation, at
least 20 in (50 cm) from adjacent surfaces.
•Do not leave any flammable material within 50 cm of this
product while operating or connected to power.
•Use a safety cable when mounting this product overhead.
•Do not operate this product outdoors or in any location where
dust, excessive heat, water, or humidity may affect it.
•Do not operate this product if the housing, lenses, or cables
appear damaged.
•Do not connect this product to a dimmer or rheostat.
•Only connect this product to a grounded and protected circuit.
•Only use the hanging/mounting bracket or the handles to carry
this product. Do not carry the product by the moving head.
•In the event of a serious operating problem, stop using
immediately.
•The maximum ambient temperature is 104 °F (40 °C). Do not
operate this product at higher temperatures.

EN Q-Wash™ 419Z-LED QRG
3
What Is
Included
•Q-Wash™ 419Z-LED
•Power input cord
•2 Omega brackets
•Safety cable
•Warranty card
•Quick Reference Guide
AC Power
This product has an auto-ranging power supply that can work with
an input voltage range of 100 to 240 V, 50/60 Hz.
Power Linking
You can link up to 5 Q-Wash™ 419Z-LED products at 120 V or
9 at 230 V. Never exceed this number. Power linking cords can be
purchased separately.
AC Plug
Connection
Wire (U.S.)
Wire (Europe)
Screw Color
AC Live
Black
Brown
Yellow/Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green
Replacing
the
Fuse
Disconnect this product from power.
1. Using a Phillips #2 head screwdriver, unscrew the fuse holder
cap from the housing.
2. Using the same type and rating, remove the blown fuse and
replace it with a good fuse.
3. Screw the fuse holder cap back into place and reconnect power.
DMX Linking
The Q-Wash™ 419Z-LED will work with a DMX controller using a
regular DMX serial connection. For more information on how to
configure for DMX operation, see DMX Primer from
www.chauvetpro.com.
DMX
Connection
The Q-Wash™ 419Z-LED uses a regular DMX data connection for
its DMX personalities: PERSON1, PERSON2, PERSON3,
PERSON4, and PERSON5. See the user manual to connect and
configure for DMX operation.
Master/Slave
Connection
The Q-Wash™ 419Z-LED uses the DMX data connection for its
Master/Slave mode. See the user manual to connect and configure
for master/slave operation.

Q-Wash™ 419Z-LED QRG EN
4
Mounting Procedures
Control
Panel
Description
Button
Function
MENU
Exits from the current menu or function
ENTER
Enables the currently displayed menu or sets the currently
selected value into the selected function
UP Navigates upwards through the menu list and increases the
numeric value when in a function
DOWN Navigates downwards through the menu list and decreases
the numeric value when in a function
Password
If you are prompted to enter a password on the product, press the
buttons in the following order: UP > DOWN > UP > DOWN >
ENTER.
The product’s password cannot be changed and must be entered
whenever you are prompted. For more information on how to set a
password for your product, see the user manual at
www.chauvetlighting.com.
Overhead Mounting
Floor Mounting
Safety Cable
Clamp

EN Q-Wash™ 419Z-LED QRG
5
Menu Options
Main Level
Programming Levels
Description
ADDRESS
000-512
Sets the DMX starting address
PERSON
PERSON1
10-Channel mode
PERSON2
21-Channel mode
PERSON3
8-Channel mode
PERSON4
21-Channel mode
PERSON5
34-Channel mode
SETTINGS PERFORM
FANS
SLOW
Selects the fan’s operation mode.
NORM
FAST
AUTO
PT SPEED
FAST
Defines the speed of the pan/tilt
SLOW
PAN INVERT
NORM
Defines the direction of the pan fader
INVERT
TILT INVERT
NORM
Defines the direction of the tilt fader
INVERT
OPTICS
SPEED
FAST
Defines the speed of the zoom
SLOW
BLACKOUT
DELAY
Activates the move-in black delay
(3 sec)
INSTANT
DIMMER
DIM4
Slow (DIM4) to fast (DIM1) dimmer
curves
DIM3
DIM2
DIM1
OFF
Linear dimmer/no dimmer function
CURV
CURV3
Slow (CURV3) to fast (CURV1)
dimmer curves
CURV2
CURV1
OFF
No dimmer

Q-Wash™ 419Z-LED QRG EN
6
Menu Options (cont.)
Main Level
Programming Levels
Description
SETTINGS
(cont.)
PERFORM
(cont.)
DIM INVERT
NORM
Defines the direction of the dimmer
fader
INVERT
COLOR
UC
Universal color balance
RGBtoW
RGB set to “255” = balanced white
OFF
RGB set to “255” = max. output
DMX ERROR SAVE
Continues with last command upon
loss of DMX control
BLACK
Blacks out fixture upon loss of DMX
signal
DMX RESET
DMX
The DMX controller resets the product
DISPLAY
The control panel resets the product
DISPLAY ON
LONG
Determines how long the backlight of
the display will stay on after last
command button pressed
SHORT
ALWAYS
HOME
SCREEN
DMX
Displays DMX address
NAME
Displays what is programmed via
SERVICE > CONTENT level
DISPLAY
INVERT
NORM
Allows the display on the control panel
to be inverted
INVERT
ZOOM POS.
NORMAL
Zoom lens is set to factory default
BOOST
Sets the zoom lens to perform better at
longer distances
RANGE
P.START
000~255
Sets the pan start point
(pan range)
P.END Sets the pan end point
(pan range)
T.START Sets the tilt start point
(tilt range)
T.END Sets the tilt end point
(tilt range)
USE
NO
Activates the changes
YES
DISPLAY
LOCK
OFF
Activates/deactivates the main level
password
ON
DEFAULT ****
(Enter Password) Resets fixture to factory default settings
SEND
NO
Sends ALL settings of the 1st product
to all other Q-Wash™ 419Z-LEDs
connected to the DMX output
YES

EN Q-Wash™ 419Z-LED QRG
7
Menu Options (cont.)
Main Level
Programming Levels
Description
STAND ALONE
RUN
DMX 512
Selects DMX running mode
AUTO1
Selects the first automatic program
AUTO2
Selects the second automatic program
CUSTOM
Selects a user customizable program
TEST
Starts the product’s test sequence
SLAVE
Selects the Slave running mode
EDIT
STEP
01~49
Selects the program step
PAN
000~255
Selects the pan position
TILT
Selects the tilt position
RED
Combines red, green, blue, and white
to obtain a custom color
GREEN
BLUE
WHITE
DIMMER
Selects the dimmer value
STROBE
Selects the strobe frequency
ZOOM
Select the zoom position
TIME
Selects the step duration
USE
NO
Activates the changes
YES
SEND NO Sends CUSTOM settings of the 1st
product to all other Q-Wash™ 419Z-
LEDs connected to the DMX output
YES
INFO
SOFTWARE
V.X.X
Shows the version of software installed
MANUAL RESET
ALL RESET
NO
Resets fixture to home settings
YES
PT.RESET
NO
Resets the Pan/Tilt to home settings
YES
OPTIC RESET
NO
Resets the Zoom to home settings
YES

Q-Wash™ 419Z-LED QRG EN
8
Menu Options (cont.)
Main Level
Programming Levels
Description
MANUAL
(cont.) MANUAL
PAN
000~255 Allows manual control of all settings
from control panel
TILT
RED
GREEN
BLUE
WHITE
DIMMER
STROBE
ZOOM
SERVICE
CALIB.M
PAN
000~255 Calibrates the start position of the
motors
TILT
ZOOM
CALIB.C
3200K
RED
000~255
Sets color temperature for White 1
GREEN
BLUE
WHITE
3400K
RED
Sets color temperature for White 2
GREEN
BLUE
WHITE
4200K
RED
Sets color temperature for White 3
GREEN
BLUE
WHITE
4900K
RED
Sets color temperature for White 4
GREEN
BLUE
WHITE
5600K
RED
Sets color temperature for White 5
GREEN
BLUE
WHITE
5900K
RED
Sets color temperature for White 6
GREEN
BLUE
WHITE

EN Q-Wash™ 419Z-LED QRG
9
Menu Options (cont.)
Main Level Programming Levels Description
SERVICE
(cont.)
CALIB.C
(cont.)
6500K
RED
000~255
Sets color temperature for White 7
GREEN
BLUE
WHITE
7200K
RED
Sets color temperature for White 8
GREEN
BLUE
WHITE
8000K
RED
Sets color temperature for White 9
GREEN
BLUE
WHITE
8500K
RED
Sets color temperature for White 10
GREEN
BLUE
WHITE
10000K
RED
Sets color temperature for White 11
GREEN
BLUE
WHITE
RGBTOW
RED
Defines the color temperature used
when COLOR is set to RGBTOW
GREEN
BLUE
ACCESS
SETTINGS
LOCK
OFF
Activates/deactivates the
SETTINGS
main level password
ON
SERVICE
LOCK
OFF
Activates/deactivates the
SERVICE
main level password
ON
CONTENT
DISPLAY1
*********
Allows 16 characters of text to be
displayed on control panel
DISPLAY2
*********
SEND NO
Sends CONTENT settings of the 1st
product to all other Q-Wash™ 419Z-
LEDs connected to the DMX output
YES
Service Recovery
****
(Enter Password)
Resets all custom modes to default
values

Q-Wash™ 419Z-LED QRG EN
10
DMX Values
PERSON1
Channel
Function
Value
Percent/Setting
1
Pan
000 ó255
0~100%
2
Tilt
000 ó255
0~100%
3
Red
000 ó255
0~100%
4
Green
000 ó255
0~100%
5
Blue
000 ó255
0~100%
6
White
000 ó255
0~100%
7
Dimmer
000 ó255
0~100%
8 Strobe
000 ó009
010
ó
255
No Function
0~100%
9
Zoom
000 ó255
0~100%
10 Control
000 ó019
020 ó039
040 ó059
060 ó079
080 ó099
100 ó119
120 ó139
140 ó149
150 ó159
160 ó169
170 ó179
180 ó199
200 ó219
220 ó235
236 ó239
240 ó243
244 ó247
248 ó251
252 ó255
No Function
Pan/tilt black activation
Pan/tilt black deactivation
Automatic fan speed
Slow fan speed
Normal fan speed
High fan speed
Auto program 1 (3 s activation delay)
Auto program 2 (3 s activation delay)
Test (3 s activation delay)
Custom program (3 s activation delay)
No Function
Reset (3 s activation delay)
No Function
DIM0 (3 s activation delay)
DIM1 (3 s activation delay)
DIM2 (3 s activation delay)
DIM3 (3 s activation delay)
DIM4 (3 s activation delay)