Cherry 8000LPBUS Installation manual

numeric keypad
mag-stripe reader
main keyboard
1. If the keyboard is connected to a Windows-based computer, exit all WordStock programs and
open Windows ‘Notepad’ or another word processing program, such as MS Word.
2. If the keyboard is attached to a QNX-based WordStock computer, close all WordStock programs
and open the word processor in the ‘Office’ menu. (You need to do this because the program-
ming process will display commands on-screen as you type them.)
3. Enter Programming mode by simultaneously pressing the <CtrlCtrl
CtrlCtrl
Ctrl-AltAlt
AltAlt
Alt-ShiftShift
ShiftShift
Shift> keys on bothboth
bothboth
both sides of
the main keyboard, i.e., press all 6 keys at oncepress all 6 keys at once
press all 6 keys at oncepress all 6 keys at once
press all 6 keys at once. Hold down all 6 keys until you hear two beeps
and see ***Menu Entry******Menu Entry***
***Menu Entry******Menu Entry***
***Menu Entry*** on the screen.
4. Type these keys in sequence: <jj
jj
j><11
11
1><yy
yy
y> to activate Track 1.
The screen displays: Magnetic-Magnetic-
Magnetic-Magnetic-
Magnetic-Card Option: TCard Option: T
Card Option: TCard Option: T
Card Option: Track #1 Rrack #1 R
rack #1 Rrack #1 R
rack #1 Reading = YESeading = YES
eading = YESeading = YES
eading = YES
5. Type: <jj
jj
j><22
22
2><yy
yy
y> to activate Track 2.
The screen displays: Magnetic-Magnetic-
Magnetic-Magnetic-
Magnetic-Card Option: TCard Option: T
Card Option: TCard Option: T
Card Option: Track #2 Rrack #2 R
rack #2 Rrack #2 R
rack #2 Reading = YESeading = YES
eading = YESeading = YES
eading = YES
6. Type: <jj
jj
j><33
33
3><nn
nn
n> to activate Track 3.
The screen displays: Magnetic-Magnetic-
Magnetic-Magnetic-
Magnetic-Card Option: TCard Option: T
Card Option: TCard Option: T
Card Option: Track #3 Rrack #3 R
rack #3 Rrack #3 R
rack #3 Reading = NOeading = NO
eading = NOeading = NO
eading = NO
7. Type: <jj
jj
j><44
44
4><nn
nn
n> to activate Track 4.
The screen displays: Magnetic-Magnetic-
Magnetic-Magnetic-
Magnetic-Card Option: TCard Option: T
Card Option: TCard Option: T
Card Option: Track #4 Rrack #4 R
rack #4 Rrack #4 R
rack #4 Reading = NOeading = NO
eading = NOeading = NO
eading = NO
8. Type: <vv
vv
v><55
55
5>.
The screen displays: Please insert Header!Please insert Header!
Please insert Header!Please insert Header!
Please insert Header!
WW
WW
WordStockordStock
ordStockordStock
ordStock SalesSales
SalesSales
Sales (800) 753-WORD www.wordstock.com [email protected]
V4.905
WordStock
Cherry Keyboard Programming
For reading IndieBound Gift Cards
This document describes how to program a
Cherry brand keyboard to work with
WordStock so that you can read IndieBound
gift cards with the keyboard’s built-in mag-
stripe reader.
• The keyboard model that WordStock uses
is 8000LPBUS8000LPBUS
8000LPBUS8000LPBUS
8000LPBUS.

9. Type: <;;
;;
;> to designate ‘;’;’
;’;’
;’ [semi-colon] as the Track 1 header, then press <EnterEnter
EnterEnter
Enter> on the
numeric keypadnumeric keypad
numeric keypadnumeric keypad
numeric keypad to end the Track 1 header programming sequence.
The previous line will be overwritten by: Magnetic-Magnetic-
Magnetic-Magnetic-
Magnetic-Card Header: #1 Defined and EnabledCard Header: #1 Defined and Enabled
Card Header: #1 Defined and EnabledCard Header: #1 Defined and Enabled
Card Header: #1 Defined and Enabled
10. Type <ww
ww
w><55
55
5> to set the Track 1 terminator sequence.
The screen displays: Please insert TPlease insert T
Please insert TPlease insert T
Please insert Terminator!erminator!
erminator!erminator!
erminator!
11. Type: <??
??
?> then press <EnterEnter
EnterEnter
Enter> on the numeric keypadnumeric keypad
numeric keypadnumeric keypad
numeric keypad to end the Track 1 terminator program-
ming sequence.
The previous line will be overwritten by: Magnetic-Magnetic-
Magnetic-Magnetic-
Magnetic-Card TCard T
Card TCard T
Card Terminator: #1 Defined anderminator: #1 Defined and
erminator: #1 Defined anderminator: #1 Defined and
erminator: #1 Defined and
EnabledEnabled
EnabledEnabled
Enabled
12. Type <vv
vv
v><66
66
6> to set the Track 2 header.
The screen displays: Please insert Header!Please insert Header!
Please insert Header!Please insert Header!
Please insert Header!
13. Type <;;
;;
;> to designate ;;
;;
; [semi-colon] as the Track 2 header, then press <EnterEnter
EnterEnter
Enter> on the numericnumeric
numericnumeric
numeric
keypadkeypad
keypadkeypad
keypad to end the Track 2 header programming sequence.
Previous line will be replaced by: Magnetic-Magnetic-
Magnetic-Magnetic-
Magnetic-Card Header: #2 Defined and EnabledCard Header: #2 Defined and Enabled
Card Header: #2 Defined and EnabledCard Header: #2 Defined and Enabled
Card Header: #2 Defined and Enabled
14. Type <ww
ww
w><66
66
6> to set the Track 2 terminator sequence;
The screen displays: Please insert TPlease insert T
Please insert TPlease insert T
Please insert Terminator!erminator!
erminator!erminator!
erminator!
15. Type <??
??
?> then press <EnterEnter
EnterEnter
Enter> on the MAINMAIN
MAINMAIN
MAIN keyboard and then press enter on the NUMERICNUMERIC
NUMERICNUMERIC
NUMERIC
keyboard to end the Track 2 terminator programming sequence.
The previous line will be overwritten by: Magnetic-Magnetic-
Magnetic-Magnetic-
Magnetic-Card TCard T
Card TCard T
Card Terminator: #2 Defined anderminator: #2 Defined and
erminator: #2 Defined anderminator: #2 Defined and
erminator: #2 Defined and
EnabledEnabled
EnabledEnabled
Enabled
16. Press the ‘space’ bar to exit from programming mode; you should see ***Menu Exit******Menu Exit***
***Menu Exit******Menu Exit***
***Menu Exit*** on the
screen.