Chess mymesh COPD17M User manual

Mymesh Product Sheet
Connect any light, anywhere.
MYMESH-COPD17M
IP66 Rated Compact Passive Infra Red (PIR)
Occupancy Detector & Photocell
(Input: 100-240 Vac 50/60Hz)
This MYMESH-COPD17M Lighting Control has an IP66
rated weatherproof enclosure and can be surface
mounted onto an external wall. Confi gurable for any
room occupancy style, via the Mymesh App.
Installation:
Please read these instructions before installing the
product.
NOTE: MYMESH-COPD17M is compatible with Mymesh
commissioning tools.
To be installed by a competent person with reference
to BS 7671 or equivalent local standards. If in doubt
consult a qualifi ed electrician.
• Plan where the MYMESH-COPD17M is to be located
(see diagram 1). Switch off supply and check for
hidden cables and pipes.
• The detector should be sited so that it is not shaded
from daylight.
• Make sure the power is isolated from the circuit.
• Remove the front cover by by removing the two
screws on the front face of the product.
• The detector should be mounted between 1 and 2.2
metres high, via any of the four pre-drilled mounting
holes only and must be mounted with the cable
entering from below.
• Thread mains cable carefully through the required
membrane entry point.
• The MYMESH-COPD17M should be connected as
shown in diagram 2:
L - Live in. N - Neutral in.
• Replace the front cover ensuring the two screws are
secured.
Operation:
To check the operation of the MYMESH-COPD17M:
• Turn on the supply then after 20 seconds if the sensor
has recognised movement of a person within its
zone of detection the integral red LED on MYMESH-
COPD17M will stay illuminated for 4 seconds before
the red LED turns off .
• Thereafter, every time movement is detected by
MYMESH-COPD17M the integral red LED will stay
illuminated for 4 seconds.
The control also features adjustable time out (time
lag) control and daylight threshold control which are
confi gured by the Mymesh App.
Precautions:
• Do not place the MYMESH-COPD17M near heat
sources, fans or in ventilated ceiling voids.
• MYMESH-COPD17M can be wired in parallel (sharing
the same Live and Neutral).
• Do not place close to, or positioned such
that, any light source points directly into the
MYMESH-COPD17M.
• Ensure wires and cables are securely held within the
connection terminals.
• The MYMESH-COPD17M should be protected by a 5
or 6 Ampere mcb or fuse.
• Disconnect the MYMESH-COPD17M from the circuit
before performing insulation testing of the wiring
circuit.
Status LED blinking sequence:
Normal: Both LED’s off .
Identifi cation of device: Red LED blinks.
16/04/20 DAT0071 MYMESH-COPD17M (Issue 01)

Chess Wise B.V. | Richard Holkade 8A | 2033 PZ Haarlem | The Netherlands
http://chess.nl | inf[email protected] | Tel: [phone]
Technical details:
INPUT
Voltage: 100 - 240Vac
Frequency: 50/60Hz
Max. mains current: 20mA
Standby current: 14mA
RADIO TRANSCEIVER
Operating frequencies: 2.4... 2,483 GHz
Max. output power: +4 dBm
LUX PARAMETERS
Range: 5 - 2000 lux
OPERATING CONDITIONS
Note: The temperature diff erence between the detection target
and the background must be at least 4 °C.
Ambient temperature: -20... +40 °C (lout 20mA)
Storage temperature: -25... +75 °C
Max. relative humidity: 0... 80%, non cond.
CONNECTORS
Terminal block Wire size: 0.5mm2- 2.5mm2solid or stranded
Wire strip length: 6-7mm
Tightening torque: 0,4 Nm/4 Kgf.cm
MECHANICAL DATA
Dimensions: 75mm x 60mm x 37mm
Weight: 111g (unpacked)
Degree of protection: IP66
Protection class: Built-in Class 2
Material (casing) Flame-retardant polycarbonate/
polypropylene
Finish / Colour Matt /White (RAL 9003)
Protection class: Built-in Class 2
CONFORMITY AND STANDARDS
EMC emission:
EN 301 489-1 V2.2.0,
EN 301 484-3,
EN 55032: 2015,
EN61000-3-2: 2014,
EN61000-3-3: 2013
EMC immunity:
EN 301 489-1 V2.2.0,
EN 301 484-3
Environment:
Complies with WEEE and RoHS directives
CB scheme:
IEC60669-1:1998,
IEC60669-1:1998/AMD1:1999,
IEC60669-1:1998/AMD2:2006,
IEC60669-2:2002,
IEC60669-2-1:2002/AMD1:2008
Radio:
EN 300 440
5 YEAR WARRANTY
MYMESH-COPD17M comes with
a 5 year warranty from the date of
manufacture and is CE marked.
DIAGRAM 1:
Detection
DIAGRAM 2:
Wiring:
DIAGRAM 3:
Dimensions:
MYMESH-COPD17M: Technical Specifi cations
L
230Vac
5A or 6A MCB
or fuse
L - Live in. N - Neutral in.
N
L
N
10
65
37
24
60
frontside
20mm threaded
entry spout
inside
4 x mounting
holes. 3M screws
recommended
(not supplied)
17
48
up to 20m
up to 24m
Strong detection zone
i.e. person moving arm
or walking towards PIR
For optimum coverage recommended
mounting height: 17m
Secondary detection
zone i.e. person walking
perpendicular to PIR
Strong detection
zone (up to 10m)
Recommended
wall mounting
height 1 to 2.2
metres