Chauvet COLORado 1 IP User manual

User Manual

Edition Notes
COLORado™ 1 IP User Manual Rev. 2
Edition Notes
The COLORado™ 1 IP User Manual Rev. 02
covers the description, safety
precautions, installation, programming, operation, and maintenance of the
COLORado™ 1 IP. CHAUVET® released this edition of the COLORado™ 1 IP User
Manual in March 2012.
Trademarks
CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET®
or Chauvet). The CHAUVET® logo in its entirety including the CHAUVET® name
and the dotted triangle, and all other trademarks i
n this manual pertaining to
services, products, or marketing statements (example: It’s Green Thinking™
) are
owned or licensed by CHAUVET®. Any other
product names, logos, brands,
company names, and other trademarks featured or referred to within this document
are the property of their respective trademark holders.
Copyright Notice
CHAUVET® owns the content of this User Manual in its entirety, including but not
limited to pictures, logos, trademarks, and resources.
© Copyright 2012 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Manual Usage
CHAUVET® authorizes its customers to download and print this manual for
professional information purposes only. CHAUVET® expressly prohibits the usage,
copy, storage, distribution, modification, or printing of this manual or its content for
any other purpose without written consent from CHAUVET®.
Document Printing
For better results, print this document in color, on letter size paper (8.5 x 11 in),
double-sided. If using A4 paper (210 x 297 mm), configure your printer to scale the
content accordingly.
Intended Audience
Any person in charge of installing, operating, and/or maintaining this product should
completely read through the guide that shipped with the product, as well as this
manual, before installing, operating, or maintaining this product.
Disclaimer
CHAUVET® believes that the information contained in this manual is accurate in all
respects. However, CHAUVET® assumes no responsibility for any errors or
omissions in this document. CHAUVET® reserves the right to revise and make
changes to the content of this document without obligation that CHAUVET® notify
any person or company of such revision or changes. This does not in any way
constitute a commitment by CHAUVET® to make such changes. CHAUVET® may
issue a revision of this manual or a new edition to incorporate such changes.
Document Revision
The COLORado™ 1 IP User Manual Rev. 02 supersedes all previous v
ersions of
this manual. Discard any older versions of this manual you may have, whether in
printed or electronic format, and replace with this version.
Author Date Editor Date
D. Couppe 3/6/12 S. Graham 5/1/12

Table of Contents
COLORado™ 1 IP User Manual Rev. 2 -i-
Table of Contents
1. Before You Begin...............................................................................................1
What Is Included............................................................................................................ 1
Unpacking Instructions................................................................................................... 1
Claims ...................................................................................................................................1
Typographic Conventions............................................................................................... 1
Symbols......................................................................................................................... 1
Safety Notes.................................................................................................................. 2
Personal Safety......................................................................................................................2
Mounting and Rigging.............................................................................................................2
Power and Wiring...................................................................................................................2
Operation...............................................................................................................................2
Expected LED Lifespan.................................................................................................. 2
2. Introduction........................................................................................................3
Product Description........................................................................................................ 3
Features ........................................................................................................................ 3
Additional Features.................................................................................................................3
Options..................................................................................................................................3
Product Overview........................................................................................................... 4
3. Setup...................................................................................................................5
AC Power ...................................................................................................................... 5
AC Plug .................................................................................................................................5
Power Linking ........................................................................................................................5
DMX Linking .................................................................................................................. 6
DMX Modes...........................................................................................................................6
Master/Slave Connectivity.......................................................................................................6
ID Addressing ................................................................................................................ 6
Mounting........................................................................................................................ 7
Orientation .............................................................................................................................7
Rigging..................................................................................................................................7
4. Operation............................................................................................................8
Control Panel Description............................................................................................... 8
Control Options.............................................................................................................. 8
Programming................................................................................................................. 8
DMX Personality.....................................................................................................................8
DMX Control Without ID Addressing........................................................................................9
DMX Control With ID Addressing............................................................................................9
Static Color..........................................................................................................................10
Auto Programs.....................................................................................................................10
Edit Customs........................................................................................................................10
Master/Slave........................................................................................................................10
Color Settings.......................................................................................................................11
Dimmer Curves....................................................................................................................11
Control Panel Lock...............................................................................................................11
Program Upload...................................................................................................................12
Reset...................................................................................................................................12
Whites Setting......................................................................................................................13
White Calibration..................................................................................................................13
TOUR Notes.................................................................................................................14
Master Dimmer.....................................................................................................................14
Red, Green, Blue, and White Color Selection ........................................................................14
Color Macros........................................................................................................................14
Strobe..................................................................................................................................14
Auto/Custom ........................................................................................................................14

Table of Contents
-ii- COLORado™ 1 IP User Manual Rev. 2
Dimmer Speed .....................................................................................................................14
ID Address Selection............................................................................................................14
Menu Map.....................................................................................................................15
DMX Values..................................................................................................................17
TOUR..................................................................................................................................17
TOUR (cont.)........................................................................................................................18
ARC.1..................................................................................................................................18
AR1.d ..................................................................................................................................18
ARC.2..................................................................................................................................18
AR2.D..................................................................................................................................19
AR2.S..................................................................................................................................19
HSV.....................................................................................................................................19
5. Technical Information......................................................................................20
Product Maintenance....................................................................................................20
Troubleshooting Guide..................................................................................................21
Returns.........................................................................................................................22
Contact Us....................................................................................................................22
Technical Specifications................................................................................................23

Before You Begin
COLORado™ 1 IP User Manual Rev. 2 -1-
1. Before You Begin
What Is
Included
•One COLORado™ 1 IP
•One Power Input Cable (IP66 To Edison,
U.S. Market)
•One IP66 Power Extension Cable
•One IP66 Signal Extension Cable
•One DMX Input Cable (IP66 To 3-Pin
XLR Male)
•One DMX Output Cable (IP66 To 3-Pin
XLR Female)
•One Gel Frame Holder
•One Safety Cable
•One Warranty Card
•One Quick Reference Guide
Unpacking
Instructions
Immediately upon receiving this product, carefully unpack the items and inspect the
container. Make sure you have received all the parts indicated above and that all the parts
are in good condition.
Claims
If the container or the material inside the container (the product and
included accessories)
appear damaged from shipping, or show
signs of mishandling, notify the carrier
immediately upon receipt, not CHAUVET®. Failure to notify the carrier
in a timely manner
may invalidate your claim. In addition, keep the container and all the packing material for
inspection.
For other issues such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with CHAUVET®
within seven (7) days of receiving the
merchandise.
Refer to the Contact Us section in this manual for addresses and phone numbers.
Typographic
Conventions
Convention
Meaning
1~512
A range of values in the text
50/60
A set of mutually exclusive values in the text
Claims
A new term, another document reference, or section or chapter in
this document
<SET>
A button on the product’s control panel
Settings
A product function or a menu option
MENU > Settings
A sequence of menu options
1~10
A range of menu values from which to choose in a menu
Yes/No
A set of two mutually exclusive menu options in a menu
ON
A unique value to be entered or selected in a menu
Symbols
Symbol Meaning
Critical installation, configuration, or operation information. Failure
to comply with this information may render the product partially or
completely inoperative, damage third-party equipment, or cause
harm to the user.
Important installation or configuration information. Failure to
comply with this information may prevent the product from
functioning correctly.
Useful information.
The term “DMX” used throughout this manual refers to the USITT DMX512-A digital
data transmission protocol.

Before You Begin
-2- COLORado™ 1 IP User Manual Rev.2
Safety Notes
Read all the following Safety Notes before working with this product. These notes include
important information about the installation, usage, and maintenance of this product.
There are no user-serviceable parts in this product. Any reference to servicing in
this User Manual applies only to properly certified CHAUVET®
technicians. Do not
open the housing or attempt any repairs unless you are certified by CHAUVET®.
Please refer to all applicable local codes and regulations for proper installation of
this product.
Personal Safety
•Avoid direct eye exposure to the light source while the product is on.
•Always disconnect this product from its power source before servicing.
•Always connect this product to a grounded circuit to avoid the risk of electrocution.
•Do not touch this product’s housing during operation because it may be very hot.
Mounting and
Rigging
•This product is for outdoor use (IP66); however, do not submerge in liquid or water.
•Make sure there are no flammable materials close to this product while it is operating.
•When hanging this product, always secure to a fastening device using a safety cable
(included).
Power and Wiring
•Always make sure you are connecting this product to the proper voltage in accordance
with the specifications in this manual or on the product’s specification label.
•Never connect this product to a dimmer pack or rheostat.
•Never disconnect this product by pulling or tugging on the power cable.
Operation
•Do not operate this product if you see damage on the housing, lenses, or cables. Have
the damaged parts replaced by an authorized technician at once.
•Do not cover the ventilation slots when operating to avoid internal overheating.
•The maximum ambient temperature is 104° F (40° C). Do not operate this product at a
higher temperature.
•In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your CHAUVET® product may require service, contact
CHAUVET® Technical Support.
Expected LED
Lifespan
LEDs gradually decline in brightness over time, mostly because of heat. Packaged in
clusters, LEDs exhibit higher operating temperatures than in ideal, single-LED conditions.
For this reason, using clustered LEDs at their fullest intensity significantly reduces the
LEDs’ lifespan. Under normal conditions, this lifespan can be 40,000 to 50,000 hours. If
extending this lifespan is vital, lower the operating temper
ature by improving the
ventilation around the product and reducing the ambient temperature to an optimal
operating range. In addition, limiting the overall projection intensity may also help to
extend the LEDs’ lifespan.

Introduction
COLORado™ 1 IP User Manual Rev. 2 -3-
2. Introduction
Product
Description
The COLORado™ 1 IP is an RGBW wash light based on 42 LEDs. It consists of a single
pod with a double bracket mounting yoke. The AC power comes directly into the product’s
housing through a proprietary IP66 rated power input cord. The power linking uses a
proprietary IP66 rated power link cord. The DMX input and output signals use proprietary
IP66 DMX in and DMX out cords. The fixture comes with all the necessary adapters to
connect to the proprietary IP66 cords as well a power and signal link cables. The
COLORado™ 1 IP uses a display-based control panel for programming functions.
Features
•3, 4, 5, 6, or 11-channel RGBW LED wash light (with ID addressing)
•Operating modes:
3-channel: HSV control
3-channel: RGB control
4-channel: RGB, dimmer
4-channel: RGBW
5-channel: RGBW, dimmer
6-channel: RGBW, dimmer, strobe
11-channel: RGBW, dimmer, color macro, strobe, auto/custom, speed, ID
addressing, dimmer speed
•RGBW color mixing with or without DMX controller
•Automatic programs
•User configurable custom programs
•Recall auto and custom programs via master/slave or DMX
•
Color temperature presets
Additional
Features
•Five distinct dimming curves
•3-pin DMX input and output connectors
•Power linking: max 12 units @ 120 V
•LED display with password protection
•Gel frame holder (4 mm max thickness)
•Double-bracket yoke that doubles as floor stand
•Color calibration
•Durable and weather resistant IP66 rated housing
•
IP66 power and DMX connectors
Options
•Optical systems: 15° (installed), 30° (CLENS3042)
•16.4 ft (5 m) power extension cable (IP5POWER)
•
16.4 ft (5 m) signal extension cable (IP5SIG

Introduction
-4- COLORado™ 1 IP User Manual Rev.2
Product Overview
Power In
Power Out
Safety Cable Loop
DMX In
A = 30 mm
B = 13 mm
DMX Out
Control Panel

Setup
COLORado™ 1 IP User Manual Rev. 2 -5-
3. Setup
AC Power
The COLORado™ 1 IP has an auto-ranging power supply that works with an input voltage
range of 100~240 VAC, 50/60 Hz.
Make sure that you are connecting this product to the proper voltage.
To determine the
power requirements for the COLORado™ 1 IP, refer to the specification label affixed to the
product or the specifications in this manual.
Refer to the Technical Specifications chart.
Always connect this product to a protected circuit with an appropriate electrical
ground to avoid the risk of electrocution or fire.
The listed current rating indicates the maximum current draw during normal operation. For
more information, download the document Sizing Circuit Breakers from the CHAUVET
®
website: www.chauvetpro.com.
Never connect this product to a rheostat (variable resistor) or dimmer circuit, even if
the rheostat or dimmer channel serves only as a 0% to 100% switch.
AC Plug
The COLORado™ 1 IP comes with IP66 rated cords for Power In and Power Out with
proprietary IP66 connectors. These power cords access the sealed body of the fixture
through IP66 cable glands. To allow connection to power outlets, the fixture comes with a
power input cord with a proprietary IP66 connector on one end and an Edison
plug on the
other end (US market). If the power input cord that came with your product has no plug,
or
if you need to change the Edison plug, use the table below to wire the new plug.
Connection
Wire (U.S.)
Wire (Europe)
IP66 Pin
Screw Color
AC Live Black Brown 1 Yellow or Brass
AC Neutral White Blue 2 Silver
AC Ground Green/Yellow Green/Yellow 3 Green
Power Linking
The COLORado™ 1 IP supports power linking. You can power link up to 12 products
at
120 VAC or 24 at 230 VAC.
This product comes with a power input cord and an IP66 power linking cord to allow direct
connection between fixtures.

Setup
-6- COLORado™ 1 IP User Manual Rev.2
DMX Linking
You can link the COLORado™ 1 IP to a DMX controller using a standard DMX serial
connection. If using other DMX compatible products with the COLORado™ 1 IP, you can
control each individually with a single DMX controller.
DMX Modes
The COLORado™ 1 IP uses the standard DMX data connection for the TOUR, ARC.1,
AR1.D, ARC.2, AR2.D, AR2.S, and HSV DMX modes.
Refer to the Introduction chapter for a brief description of these modes.
Refer to the Operation chapter to learn how to configure the COLORado™ 1 IP to work in
these modes.
The DMX Values section will provide you with detailed information regarding the DMX
modes.
Master/Slave
Connectivity
The Master/Slave mode allows a COLORado™ 1 IP (the “master product”) to control one or
more COLORado™ 1 IPs (the “slave products”) without a DMX controller. One
COLORado™ 1 IP becomes the master product when running an Auto or Custom program,
or by being in STAT mode.
You must configure each slave product’s control panel to operate in SLAV mode
. During
Master/Slave operation, the slave products will operate in unison with the master product.
The COLORado™ 1 IP comes with two adapter cables, one from proprietary IP66 to 3-pin
DMX In and the other from proprietary IP66 to 3-pin DMX Out. In addition, it comes with a
signal linking cable with proprietary IP66 connectors on both ends.
If you are not familiar with or need more information about DMX standards, Master/Slave
connectivity, or the DMX cables needed to link this product to a DMX controller, download
the DMX Primer from the CHAUVET® website: www.chauvetpro.com.
DO NOT connect a DMX controller to products operating in Master/Slave mode. The
DMX controller signals may interfere with the signals from the master product.
The Operation chapter of this manual provides detailed instructions on how to
configure the Master and Slave products.
ID Addressing
The COLORado™ 1 IP
uses the ID Addressing feature to increase the number of
addressable products in the same DMX universe when in the TOUR personality.
Refer to the Operation chapter in this manual to learn in detail how to configure this product
when using ID Addressing.
If you are not familiar with the various connection methods when using ID Addressing,
download the DMX Primer from the CHAUVET® website: www.chauvetpro.com.

Setup
COLORado™ 1 IP User Manual Rev. 2 -7-
Mounting
Before mounting this product, read and follow the Safety Notes in this manual.
Orientation
Always mount this product in a safe position and make sure there is adequate room for
ventilation, configuration, and maintenance.
Rigging
The COLORado™ 1 IP consists of a sealed (IP66) housing with a double bracket mounting
yoke. It has two DMX signal cables (DMX In/DMX Out), and two power cables (Power
In/Power Out), all of them fitted with proprietary IP66 connectors. CHAUVET®
recommends using the following general guidelines when mounting this product.
•When selecting an installation location, consider easy access to this product for
operation, programming adjustments, and routine maintenance.
•Make sure to mount this product away from any flammable material as indicated in the
Safety Notes.
•Never mount in places where rain, high humidity, extreme temperature changes, or
restricted ventilation may affect the product.
•If hanging this product, make sure that the mounting location can support the product’s
weight. Refer to the Technical Specifications chart for the weight-bearing requirements
of this product.
•When hanging this product, always secure to a fastening device using a safety cable
(included).
Procedure
The COLORado™ 1 IP comes with double bracketed mounting yoke to
which you can
attach clamps. These brackets also serve as floor stands or wall-mount supports. You
must supply your own clamps and make sure the clamps
are capable of supporting the
weight of this product.
Product Mounting
Diagram
Overhead Mounting
Floor Mounting

Operation
-8- COLORado™ 1 IP User Manual Rev.2
4. Operation
Control Panel
Description
Button Function
<MENU> Exits from the current menu or function
<ENTER> Enables the currently displayed menu or sets the currently selected value in to the
current function
<UP> Navigates upward through the menu list and increases the numeric value when in a
function
<DOWN> Navigates downward through the menu list and decreases the numeric value when in a
function
Control Options
You can set the COLORado™ 1 IP start address in the 001~512 DMX range. This enables
control of up to 46 products in the 11-channel TOUR personality.
In addition, the ID address system allows you to assign up to 66 products for each starting
DMX address, multiplying the number of products you can control within a single universe.
You can access the product’s ID address system from channel 11 when in the TOUR DMX
personality.
When programming live performances, as well as cues that need to trigger on
demand or on a time line, if using Id addressing, program no more than 10 products
per DMX channel. This is to remain within a one-second execution time.
Programming
Refer to the Menu Map to understand the menu options. The menu map shows the main
level and a variable number of programming levels for each option.
•To go to the desired main level, press <MENU> repeatedly until the option shows on
the display. Press <ENTER> to select. This will take you to the first programming level
for that option.
•To select an option or value within the current programming level, press <UP> or
<DOWN> until the option shows on the display. Press <ENTER> to select. In this
case, if there is another programming level, you will see that first option, or you will see
the selected value.
•Press <MENU> repeatedly to exit to the previous main level.
DMX Personality
This setting allows you to choose a particular DMX personality.
1. Go to the PERS main level.
2. Select the desired personality (TOUR, ARC.1, AR1.d, ARC.2, AR2.d, AR2.S, or HSV).
•See the DMX Values section for the highest starting address you can select for
each personality.
•Make sure that the starting addresses on the various products
do not overlap
due to the new personality setting.

Operation
COLORado™ 1 IP User Manual Rev. 2 -9-
DMX Control
Without ID
Addressing
In this mode, each product
will respond to a unique starting address from the DMX
controller. All products with the same starting address will respond in unison.
Select the TOUR personality as shown in DMX Personality.
1. Set the running mode:
a. Go to the RUN main level.
b. Select the DMX programming level.
2. Set the starting address:
a. Go to DMX.
b. Select the starting address (001~512).
3. Deactivate ID Addressing on each product:
a. Go to SET > Id.
b. Select
OFF
.
Make sure to deactivate ID Addressing in each product when using the TOUR
personality. Otherwise, unintended results may occur if channel 11 is not set to “0.”
The highest recommended starting address for each DMX mode are as follows:
DMX Mode DMX Address DMX Mode DMX Address DMX Mode DMX Address
TOUR
502
ARC.2
509
HSV
510
ARC.1
510
AR2.D
508
AR1.d
509
AR2.S
507
DMX Control With
ID Addressing
In this mode, the products with the same DMX starting address will respond to the DMX
controller based on the product’s individual ID address setting. If you select ID address
“0,” all the products with the same DMX address will respond in unison. Otherwise, each
product will follow the control for its particular ID address.
1. Repeat steps 1, 2, and 3from DMX Control Without ID Addressing.
2. Activate ID Addressing in each product:
a. Go to SET > Id.
b. Select ON.

Operation
-10- COLORado™ 1 IP User Manual Rev.2
Static Color
The Static Color mode allows for permanent RGBW color mixing without a DMX controller.
1. Go to the STAT main level.
2. Select the desired color (R., G., B., or W.).
3. Select the desired color value (000~255).
4. Repeat for the other colors.
5. Select ST.
6. Select the desired frequency (00~20).
Auto Programs
Auto programs allow for dynamic RGBW color mixing without a DMX controller.
1. Go to AUTO.
2. Select the desired auto (AT.01~10)or custom program (PR.01~10).
You cannot edit any of the auto programs (AT.01~10). However, you can edit the
custom programs (PR.01~10). See Edit Customs below for details.
Edit Customs
This setting allows the programming of up to 30 scenes for each of the 10 customizable
programs, including colors and effects.
1. Go to the EdIT main level.
2. Select the desired auto program (PR.01~10).
3. Select the desired scene (SC.01~30).
4. Select the desired color or effect (R., G., B., W., Sb., T., or F.).
5. Select the color or effect value (000~255 for colors and timers, or 00~20 for strobe).
6. Repeat for the other colors or effects.
7. Return to the scene level (SC. or step “3”).
8. Repeat the settings of colors and effects for the other scenes.
Master/Slave
The Master/Slave mode allows a group of COLORado™ 1 IPs (the slave products) to
simultaneously duplicate the output of another COLORado™ 1 IP (the master product)
without a DMX controller.
1. Set each of the slave products:
a. Go to RUN.
b. Select SLAV.
2. Set the master product:
a. Set the running mode to DMX as explained in DMX Control Without ID
Addressing.
b. Select an auto or custom program as explained in Auto Programs above, or a
static mix of colors.
•The master product is the one that runs a program (whether Auto or Custom) or
Static Color mode.
•Do not connect a DMX controller to the products configured for Master/Slave
operation.
The DMX controller may interfere with signals from the master
product.
•The master product should be the first product in the daisy chain.

Operation
COLORado™ 1 IP User Manual Rev. 2 -11-
Color Settings
The COLO setting determines how the COLORado™ 1 IP generates the white color based
on various RGB settings.
1. Go to the SET main level.
2. Select COLO.
3. Select OFF, RGbw., or UC.
OFF:
When all the RGB faders are set to 255, the output is maximum, although
the resulting white color may not be balanced.
RGbw.
When all the RGB faders are set to
255
, the resulting output is defined by
the configured White color (see Whites Settings).
UC:
When all the RGB faders are set to 255, the output matches that of less
efficient products (Universal Color).
Dimmer Curves
This setting determines how fast the output of the COLORado™ 1 IP changes when you
modify the values of the Red, Green, Blue, White, and Dimmer faders.
This setting
provides four different options to simulate the dimming curve of an incandescent lighting
product.
1. Go to the SET main level.
2. Select dIM.
3. Select a dimmer function (OFF, dIM1, dIM2, dIM3, or dIM4).
OFF:
The output is proportional (linear) to the Dimmer and RGBW channel
values.
dIM1~4:
The output follows the Dimmer and RGBW channel values based on the
corresponding dimmer curve, being
dIM1
the fastest and
dIM4
the slowest.
Control Panel
Lock
This setting enables you to activate or disable the control panel lock, which keeps non-
authorized personnel from changing the product’s settings.
1. Go to the KEY main level.
2. Select ON or OFF.
When the control panel lock is active, the product will prompt you to enter the
password after 30 seconds of control panel inactivity or after turning on the product.
After being prompted to enter the password:
Press <UP>, <DOWN>, <UP>, <DOWN>, and <ENTER>

Operation
-12- COLORado™ 1 IP User Manual Rev.2
Program Upload
This option allows you to copy the custom programs of one COLORado™ 1 IP onto
another COLORado™ 1 IP by using the Master/Slave mode.
1. Configure and connect the products in a Master/Slave arrangement, where the master
product has the custom programs you want to transfer to the slave products.
2. From the master product, go to the SET main level.
3. Select UPLd.
4. When PASS shows, press <ENTER>.
5. Enter the master access password as shown in Control Panel Lock.
6. When SEND shows, press <ENTER> to start the upload.
7. Wait for the upload process to finish (the display will show END/MAIN) before
continuing or turning the products off.
The Master/Slave products will provide the status of the process by lighting up as
follows:
•Yellow indicates that the upload process is running.
•Green indicates that the upload process completed successfully.
•Red indicates that the upload process failed due to an error. Recheck all cable
connections and restart the process. If the issue persists, contact CHAUVET®
Technical Support.
DO NOT upload the data from a COLORado™ 1 IP to a different product. The other
product may become inoperative.
Reset
This setting allows you to reset the COLORado™ 1 IP to the default values, including the
custom programs.
1. Go to the SET main level.
2. Select REST.
3. When PASS shows, press <ENTER>.
4. Enter the master access password as described in Control Panel Lock.
5. Wait for the reset process to finish.

Operation
COLORado™ 1 IP User Manual Rev. 2 -13-
Whites Setting
This setting allows you
to select and edit the temperature of the white colors used in
channel 11 (Macros) when in the TOUR mode. You can also
define the maximum RGB
values when RGB to White (RGbw.) is active.
1. Go to CAL1.
2. Select a white color (Wt.01~11).
3. Select a color (R., G., b., or w.).
4. Select a color value (000~255).
5. Repeat for the other colors.
When selecting RGbw., you will only be able to define the values of Red, Green, and
Blue.
The values of Red, Green, and Blue configured from CALIB > RGbw. will define the
color temperature shown when the RGB faders are set to 255 if SETTING > COLOR >
RGbw. is active.
White Calibration
This setting allows you to select the white color shown by the COLORado™ Range IP
when the color setting is RGbw. and the DMX controller’s Red, Green, and Blue faders
are set to “255.”
1. Go to the CAL2 > RGbw. level.
2. Select a color (R., G., or b.).
3. Select a color value (000~255).
4. Repeat for the other colors.
When selecting CAL2 > RGbw., you will only be able to define the values of Red,
Green, and Blue.
The values of Red, Green, and Blue configured from CAL2 > RGbw. will define the
color temperature shown when the RGB faders are set to “255” if SET > COLO >
RGbw. is active.

Operation
-14- COLORado™ 1 IP User Manual Rev.2
TOUR Notes
These notes clarify the way the TOUR DMX personality works.
Master Dimmer
•Channel 1 controls the intensity of the currently projected color.
•When the slider is at the highest position (100%), the intensity of the output is at
maximum.
Red, Green, Blue,
and White
Color
Selection
•Channels 2 through 5 control the intensity ratio of each of the Red, Green, Blue, and
White LEDs.
•When these channels are at the highest position (100%), the intensity of each color is at
maximum if SET > COLO is OFF.
•
You can combine channels 2 through 5 to create over one trillion colors.
Color Macros
•Channel 6 selects the required Color Macro.
•Channel 6 has priority over channels 2 through 5.
•
Channel 1 controls the intensity of the Color Macro.
Strobe
•Channel 7 controls the strobe frequency (not the intensity) of channels 2 through 6.
•Channel 7 can strobe channels 2 through 5 when not running macros, allowing the
individual faders (R, G, b, and w), as well as channel 1 (d), to control the output
intensity.
•Channel 7 can strobe channel 6 when running macros, allowing channel 6 to select the
macro and channel 1 to control the output intensity.
Auto/Custom
•Channel 8 selects the preset auto programs AT.01~10 or the custom programs
PR.01~10.
•When activating the custom Auto programs PR.01~10, you can control the Step Time
and Fade Time using channels 2 and 3, respectively.
•Channel 8 has priority over channels 2 through 7.
•
Channel 9 controls the speed at which each auto program plays.
Dimmer Speed
•Channel 10 selects the dimmer mode and speed. Dimmer mode provides four different
options to simulate the dimming curve of an incandescent lighting product.
•When dIM is set to OFF,the changes in the RGbw and Master Dimmer faders are linear.
•When dIM is set to dIM1~dIM4, dIM1 is the fastest dimmer curve and dIM4 is the
slowest.
ID Address
Selection
•Channel 11 selects the target ID address.
•Each independent DMX address may have up to 66 independent ID addresses.
•An ID address of
0
will activate all ID address locations.

Operation
COLORado™ 1 IP User Manual Rev. 2 -15-
Menu Map
Main Level Programming Levels Description
STAT
R.
000~255 Combines Red, Green, Blue, and
White to generate a custom color
G.
b.
w.
ST.
00~20
Strobe frequency
AUTO AT. 01~10 Choose from 10 automatic programs
PR. Choose from 10 customizable
programs
RUN
dMx
Receives signals from DMX controller
SLAV. Receives signals from Master product
dMx d. 001~512 Sets the DMX starting address
PERS
TOUR
RGBW, ID, dimmer, strobe, macro,
auto/custom, dimmer speed, auto speed
ARC.1 3 channel: RGB
AR1.D
4-channel: RGB, D
ARC.2
4-channel: RGBW
AR2.D 5-channel: RGBW, D
AR2.S 6-channel: RGBW, D, S
HSV
3 channel: HSV
ID Id. 01~66 Sets ID address control
EdIT PR. 01~10 SC. 01~30
R.
000~255 User can combine Red, Green, Blue,
and White to generate a custom color
G.
b.
W.
Sb. 00~20 Selects the strobe frequency
T.
000~255 Defines the step duration
F. Defines the fade duration
SET
UPLd. **** Uploads custom programs to other
products
REST. **** Defaults product
Id.
ON
Turns ID addressing on/off
OFF
COLO.
OFF RGB set to “255”= max. output
RGbw RGB set to “255” = balanced white
UC Universal color balance
dIM
OFF
No dimmer
dIM1
Dimmer curve
dIM2
dIM3
dIM4
Continues on Next Page

Operation
-16- COLORado™ 1 IP User Manual Rev.2
Menu Map (continued)
Main Level
Programming Levels
Description
CAL1 wT. 00~11
R.
000~255 Modifies the color macros used in the
TOUR personality
G.
b.
w.
CAL2 RGbw.
R.
000~255 Defines the color temperature used
when COLO is set to RGbw.
G.
b.
kEY
ON
Turns the password on or off
OFF