Chauvet Intimidator Spot 355 IRC User manual

User Manual

Page 2 of 25 Intimidator Spot 355 IRC User Manual Rev. 1
TABLE OF CONTENTS
1. Before You Begin .............................................................................. 4
What Is Included ...............................................................................................4
Unpacking Instructions......................................................................................4
Claims........................................................................................................................ 4
Text Conventions ..............................................................................................4
Symbols ............................................................................................................4
Disclaimer .........................................................................................................4
Product at a Glance ..........................................................................................5
Safety Notes......................................................................................................5
2. Introduction ....................................................................................... 6
Product Overview..............................................................................................6
Product Dimensions..........................................................................................7
3. Setup .................................................................................................. 8
AC Power..........................................................................................................8
Fuse Replacement..................................................................................................... 8
Power Linking............................................................................................................. 8
Mounting ...........................................................................................................9
Orientation ................................................................................................................. 9
Rigging....................................................................................................................... 9
4. Operation ..........................................................................................10
Control Panel Operation..................................................................................10
Menu Map................................................................................................................ 10
Configuration (DMX) .......................................................................................11
Starting Address....................................................................................................... 11
DMX Personalities.................................................................................................... 11
5. DMX Assignments............................................................................12
DMX14CH.......................................................................................................12
DMX14CH (cont.)............................................................................................13
DMX8CH.........................................................................................................13
DMX8CH (cont.)..............................................................................................14
Configuration (Standalone).............................................................................15
Sound-Active Mode.................................................................................................. 15
Sound Sensitivity...................................................................................................... 15
Automatic Mode....................................................................................................... 15
Totem Mode............................................................................................................. 15
Manual Test Mode ................................................................................................... 16
Pan/Tilt Orientation .................................................................................................. 16
Pan/Tilt Angle Range............................................................................................... 16
Display..................................................................................................................... 17
Reset Options .................................................................................................17
System Information.........................................................................................17
Master/Slave Mode.................................................................................................. 18
IR Mode ................................................................................................................... 19
IRC-6 Operation....................................................................................................... 19
Zero Adjust Mode............................................................................................20
Changing Gobos .............................................................................................21

Intimidator Spot 355 IRC User Manual Rev. 1 Page 3 of 25
6. Technical Information ......................................................................22
Product Maintenance......................................................................................22
7. Technical Specifications..................................................................23
Returns............................................................................................................24
Contact Us ............................................................................................25

Page 4 of 25 Intimidator Spot 355 IRC User Manual Rev. 1
1.BEFORE YOU BEGIN
What Is
Included
•Intimidator Spot 355 IRC
•Hanging Bracket with Mounting
Hardware
•Power Cord
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product immediately and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet.
Failure to report damage
to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with Chauvet within 7 days of delivery.
Text
Conventions
Convention Meaning
1–512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
Chauvet believes that the information co
ntained in this manual is accurate in all
respects. However, Chauvet assumes no responsibility and specifically disclaims any
and all liability to any party for any loss, damage or disruption caused by any errors or
omissions in this document, whether such
errors or omissions result from negligence,
accident or any other cause. Chauvet reserves the right to revise the content of this
document without any obligation to notify any person or company of such revision,
however, Chauvet has no obligation to make,
and does not commit to make, any such
revisions. Download the latest version from www.chauvetlighting.com.
The works of authorship contained in this manual, including, but not limited to, all design,
text and images are owned by Chauvet.
© Copyright 2016 Chauvet & Sons, Inc. All rights reserved.
Electronically published by Chauvet in the United States of America.
CHAUVET, the Chauvet logo, Gobo Zoom USB, D-Fi, and D-
Fi USB are registered
trademarks or trademar
ks of Chauvet & Sons Inc. (d/b/a Chauvet and Chauvet Lighting)
in the United States and other countries. Other company and product names and logos
referred to herein may be trademarks of their respective companies.

Intimidator Spot 355 IRC User Manual Rev. 1 Page 5 of 25
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Activated
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
These notes include important information about the mounting, usage, and maintenance
of this product; read before using the product.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from power before cleaning or replacing the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer or rheostat.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket.
•The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Keep this User Manual for future use. If you sell the product, give this document to the
next owner.

Page 6 of 25 Intimidator Spot 355 IRC User Manual Rev. 1
2.INTRODUCTION
Product Overview
Front Panel View
Back Panel View
Power Out
Yoke
Gobo Access
Door
LCD Display
Indicator LED
Menu
Buttons
IR Sensor
DMX In/Out
Power In
Fuse-Holder

Intimidator Spot 355 IRC User Manual Rev. 1 Page 7 of 25
Product Dimensions
12.44 in
316 mm
8.74 in
222 mm
13.39 in
340 mm
3.78 in
96 mm
9.76 in
248 mm
15.43 in
392 mm
10.55 in
268 mm

Page 8 of 25 Intimidator Spot 355 IRC User Manual Rev. 1
3.SETUP
AC Power
The Intimidator Spot 355 IRC has an auto-ranging powe
r supply and it can work with an
input voltage range of 100 to 240 VAC, 50/60 Hz.
To determine the product’s power requirements (
circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product
’s back panel, or
refer to the product
’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
•Always connect the product to a protected circuit
(circuit breaker or fuse).
Make sure the product has an appr
opriate electrical ground to avoid the risk of
electrocution or fire.
•
To eliminate unnecessary wear and improve its lifespan, during periods of
non-
use completely disconnect the product from power via breaker or by
unplugging it.
Never connect the product
to a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement
1. Disconnect the product from power.
2. Using a flat-head screwdriver, unscrew the fuse holder cap from
the housing.
3. Remove the blown fuse.
4. Replace with a fuse of the same type and rating.
5. Screw the fuse holder cap back in place and reconnect power.
•Disconnect the product from power before replacing the fuse.
•Always replace a blown fuse with another of the same type and rating.
Power Linking
The product provides power linking via the IEC outlet located in the back of the unit.
Power Linking
Diagram
You can power link up to 4 Intimidator Spot 355 IRC units on 120 VAC
or up to 7
Intimidator Spot 355 IRC units on 230 VAC.
The power linking diagram shown above corresponds to the North American
version of the product ONLY! If using the product in other markets, you must
consult with the local Chauvet distributor as pow
er linking connectors and
requirements may differ in your country or region.
1st Product
2nd Product
3rd Product
Other products

Intimidator Spot 355 IRC User Manual Rev. 1 Page 9 of 25
Mounting
Before mounting the product, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The Intimidator Spot 355 IRC may be mounted in a
ny position; however, make sure
adequate ventilation is provided around the product.
Rigging
•
Before deciding on a location for the product, always make sure there is easy
access to the product for maintenance and programming purposes.
•Make sure that th
e structure or surface onto which you are mounting the product
can support the product’s weight. See the Technical Specifications
for weight
information. The CLP-15 clamp from Chauvet is appropriate for this product.
•
When mounting the product overhead, always use a safety cable. Mount the
product securely to a rigging point, whether an elevated platform or a truss.
•When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity.
•
When power linking multiple products, you must always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
•
The rubber feet also serve as floor supports. When mounting the product on the
floor, make sure that the product and cables are away from people and vehicles.
Mounting Diagram
When using only one mounting clamp with this fixture, you must use a clamp with
a captive bolt to prevent accidental loosening.
Safety Cable
(such as CH-05 from Chauvet)
Bracket
Attachment Plate
x2
Rubber Feet for
Floor Mounting x4
Threaded Hole for
Safety Loop
(behind the foot)
Mounting Clamp
(works with
CLP15 clamp from Chauvet)
Mounting Bracket

Page 10 of 25 Intimidator Spot 355 IRC User Manual Rev. 1
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the display.
Button Function
<MENU> Press to find an operation mode or to back out of the current menu
option
<UP> Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower value
<ENTER> Press to activate a menu option or a selected value
Menu Map
Main Function
Programming Levels
Description
Address
001–512
Sets the DMX starting address
Run Mode
DMX
14CH
Selects DMX mode
08CH
Slave
Slave 1–4
Selects Slave mode 1, 2 ,3, or 4
Auto
Selects Auto mode
Sound
Selects Sound-Active mode
IR
Selects infrared control
Manual
Pan
000–255
0 to 540°
Pan Fine
Fine control of panning
Tilt
0 to 270°
Tilt Fine
Fine control of tilting
P/T Speed
Pan/Tilt speed (fast to slow)
Color
Selects color options
Gobo
Selects Gobo options
Gobo Rotate
Rotation effect with increasing speed
Prism
Selects 3-facet prism
Focus
Sets the focus
Dimmer
Sets dimmer value
Shutter
Strobe effect with increasing speed
P/T Macro
Selects pan/tilt movement macros
Special Function
Selects control functions
Setup
Pan Reverse
OFF
Normal pan operation
ON
Reverse pan operation
Tilt Reverse
OFF
Normal tilt operation
ON
Reverse tilt operation
Screen Reverse
OFF
Normal display
ON
Reverse display
Pan Angle
540
Selects the 540° pan angle range
360
Selects the 360° pan angle range
180
Selects the 180° pan angle range
Tilt Angle
270
Selects the 270° tilt angle range
180
Selects the 180° tilt angle range
090
Selects the 90° tilt angle range
Totem
OFF
Totem mode off
Up
Selects upward pan and tilt range
Down
Selects downward pan and tilt range
Sensitivity
001–100
Sound sensitivity control
Reset
Resets the product
Factory Set
Loads factory defaults
Sys Info
Ver: VX.X
Displays the software version
Running Mode: XXXXX
Displays the current running mode
DmxAddress: XXX
Displays the current DMX address
Temperature: XXX
Displays the LED temperature in Celsius

Intimidator Spot 355 IRC User Manual Rev. 1 Page 11 of 25
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The Intimidator Spot 355 IRC uses up to 14 DMX channels in its 14-channel DMX mode,
which defines the highest configurable address to 499.
If you are not familiar with the DMX protocol,
download the DMX Primer from
www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Address.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select the starting address.
5. Press <ENTER>.
DMX
Personalities
The Intimidator Spot 355 IRC has two DMX personalities, a 14-channel
personality and
an 8-channel personality.
To choose which DMX personality to use, follow the steps below:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Run Mode.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select DMX.
5. Press <ENTER>.
6. Use <UP> or <DOWN> until either 14CH (to choose the 14-channel personality) or
08CH (to choose the 8-channel personality) shows on the display.
7. Press <ENTER>.

Page 12 of 25 Intimidator Spot 355 IRC User Manual Rev. 1
5.DMXASSIGNMENTS
DMX14CH
Channel Function Value Percent/Setting
1
Pan
000
ó
255
0–540°
2
Fine Pan
000ó255
Fine control of pan
3
Tilt
000ó255
0–270°
4
Fine Tilt
000ó255
Fine control of tilt
5
Speed
000ó255
Pan/Tilt speed (fast to slow)
6 Color Wheel
000
ó
006
White
007ó013
Yellow
014ó020
Pink
021ó027
Green
028ó034
Red
035
ó
041
Light Blue
042ó048
Kelly Green
049ó055
Orange
056ó063
Dark Blue
064ó070
White + Yellow
071
ó
077
Yellow + Pink
078ó084
Pink + Green
085ó091
Green + Red
092ó098
Red + Light Blue
099ó105
Light Blue + Kelly Green
106
ó
112
Kelly Green + Orange
113ó119
Orange + Dark Blue
121ó127
Dark Blue + White
128ó191
Color cycling rainbow with increasing speed
192ó255
Reverse color cycling rainbow with increasing
speed
7 Gobo Wheel
064ó071
Gobo 7 shake (slow to fast)
072ó079
Gobo 6 shake (slow to fast)
080
ó
087
Gobo 5 shake (slow to fast)
088ó095
Gobo 4 shake (slow to fast)
096ó103
Gobo 3 shake (slow to fast)
104ó111
Gobo 2 shake (slow to fast)
112ó119
Gobo 1 shake (slow to fast)
120
ó
127
Open
128ó191
Cycle effect with increasing speed
192ó255
Reverse cycle effect with increasing speed
8 Gobo Rotation
000ó063
Index
064ó147
Rotate (slow to fast)
148
ó
231
Reverse rotate (slow to fast)
232ó255
Bounce

Intimidator Spot 355 IRC User Manual Rev. 1 Page 13 of 25
DMX14CH
(cont.)
Channel
Function
Value
Percent/Setting
9 Prism
000
ó
007
Open
008ó012
Prism on
013ó130
Prism rotate (slow to fast)
131ó247
Reverse prism rotate (slow to fast)
248ó255
Prism effects
10
Focus
000
ó
255
Motorized focus (big to small)
11
Dimmer
000ó255
0–100%
12 Shutter
000ó003
Closed
004ó007
Open
008ó076
Strobe (slow to fast)
077
ó
145
Pulse
146ó215
Random open and close
216ó255
Open
13 Control Function
000ó007
No function
008ó015
Blackout pan/tilt movement
016
ó
023
Blackout color wheel movement
024ó031
Blackout gobo wheel movement
032ó039
Disable pan/tilt/color wheel movement blackout
040ó047
Disable pan/tilt/gobo wheel movement blackout
048ó055
Disable all movement blackout
056
ó
095
No function
096ó103
Reset pan
104ó111
Reset tilt
112ó119
Reset color wheel
120ó127
Reset gobo wheel
128
ó
135
Reset gobo rotation
136ó143
Reset prism
144ó151
Reset focus
152ó159
Reset all channels
160ó255
No function
14 Movement Macros
000
ó
007
No function
108ó135
Automatic programs 1–8
136ó255
Sound-Active programs 1–8
DMX8CH
Channel
Function
Value
Percent/Setting
1
Pan
000ó255
0–540°
2
Tilt
000ó255
0–270°
3 Color Wheel
000ó006
White
007ó013
Yellow
014ó020
Pink
021ó027
Green
028ó034
Red
035ó041
Light Blue
042ó048
Kelly Green
049ó055
Orange
056ó063
Dark Blue
064ó070
White + Yellow
071ó077
Yellow + Pink

Page 14 of 25 Intimidator Spot 355 IRC User Manual Rev. 1
DMX8CH
(cont.)
Channel
Function
Value
Percent/Setting
3 Color Wheel
078
ó
084
Pink + Green
085ó091
Green + Red
092ó098
Red + Light Blue
099ó105
Light Blue + Kelly Green
106ó112
Kelly Green + Orange
113
ó
119
Orange + Dark Blue
121ó127
Dark Blue + White
128ó191
Color cycling rainbow with increasing speed
192ó255
Reverse color cycling rainbow with increasing
speed
4Gobo Wheel
064ó071
Gobo 7 shake (slow to fast)
072
ó
079
Gobo 6 shake (slow to fast)
080ó087
Gobo 5 shake (slow to fast)
088ó095
Gobo 4 shake (slow to fast)
096ó103
Gobo 3 shake (slow to fast)
104ó111
Gobo 2 shake (slow to fast)
112
ó
119
Gobo 1 shake (slow to fast)
120ó127
Open
128ó191
Cycle effect with increasing speed
192ó255
Reverse cycle effect with increasing speed
5 Gobo Rotation
000ó063
Index
064
ó
147
Rotate (slow to fast)
148ó231
Reverse rotate (slow to fast)
232ó255
Bounce
6 Prism
000ó007
Open
008ó012
Prism on
013
ó
130
Prism rotate (slow to fast)
131ó247
Reverse prism rotate (slow to fast)
248ó255
Prism effects
7
Focus
000ó255
Motorized focus (big to small)
8 Shutter
000ó003
Closed
004
ó
007
Open
008ó076
Strobe (slow to fast)
077ó145
Pulse
146ó215
Random open and close
216ó255
Open

Intimidator Spot 355 IRC User Manual Rev. 1 Page 15 of 25
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
•Connect the product to power.
Never connect a product that is operating in any standalone mode (either
Automatic or Sound-Active)
to a DMX string connected to a DMX controller.
Product
s in standalone mode may transmit DMX signals that could interfere with
the DMX signals from the controller.
Sound-
Active
Mode
To enable the Sound-Active mode, do the following.
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Run Mode.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Sound.
5. Press <ENTER>.
The product will only respond to low frequencies of music (bass and drums).
Sound Sensitivity
To set the sound sensitivity, do the following.
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Sensitivity.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select 001–100, low to high.
7. Press <ENTER>.
Automatic Mode
To enable the Automatic mode, follow the instructions below:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Run Mode.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Auto.
5. Press <ENTER>.
Totem Mode
To activate the Totem Mode, do the following:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Totem Mode.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to choose OFF, DOWN, or UP.
7. Press <ENTER>.

Page 16 of 25 Intimidator Spot 355 IRC User Manual Rev. 1
Manual Test Mode
To test or control any function of the Intimidator Spot 355 IRC
through the LCD display
menu, follow the instructions below:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Run Mode.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Manual.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select the function to test or control, from the options:
Pan, Pan Fine,Tilt, Tilt Fine, P/T Speed, Color, Gobo, Gobo Rotate, Prism,
Focus, Dimmer, Shutter, Special Function, and P/T Macros.
7. Press <ENTER>.
8. Use <UP> or <DOWN> to change the value of the selected function, from 000–255.
NOTE: For information regarding what each value range does for each
function, see the DMX Assignments for 14CH Mode.
Pan/Tilt
Orientation
To select whether the Intimidator Spot 355 IRC will
operate with normal panning or
inverted panning, do the following.
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Pan Reverse.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select ON or OFF.
7. Press <ENTER>.
To select whether the Intimidator Spot 355 IRC will operate with normal tilting or inverted
tilting, do the following:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Tilt Reverse.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select ON or OFF.
7. Press <ENTER>.
Pan/Tilt Angle
Range
The user can select the range for the pan and tilt angles on the
Intimidator Spot 355
IRC.
To select which pan angle range to use, do the following.
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Pan Angle.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select 540, 360, or 180.
7. Press <ENTER>.
To select which tilt angle range to use, do the following.
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Tilt Angle.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select 270, 180, or 090.
7. Press <ENTER>.

Intimidator Spot 355 IRC User Manual Rev. 1 Page 17 of 25
Display
The user can flip the LED display for easy readability in any mounting situation.
To select the display orientation:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Screen Reverse.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select ON or OFF.
7. Press <ENTER>.
Reset Options
The Reset
option will restart the product, but does not change any settings. Using the
Factory Set option will clear out all customized settings and retu
rn the settings to the
factory defaults To reset the software on the Intimidator Spot 355 IRC, do the following:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Setup.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to choose Reset or Factory Set.
5. Press <ENTER>.
System
Information
To view information about the Intimidator Spot 355 IRC:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Sys Info.
3. Press <ENTER>. The current information about the product will show on the
display.

Page 18 of 25 Intimidator Spot 355 IRC User Manual Rev. 1
Master/Slave
Mode
The Master/Slave mode allows a single Intimidator Spot 355 IRC
(the master) to control
the actions of one or more Intimidator Spot 355 IRC products
(the slaves) without the
need of a DMX controller. The master will be set to opera
te in either Automatic or
Sound-Active mode, while the slaves will be set to operate in Slave m
ode. Once set and
connected, the slaves will operate in unison with the master.
Configure the products as indicated below.
Slaves:
1. Press <MENU>.
2. Use <UP> or <DOWN> to choose Run Mode.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select Slave.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select Slave1, Slave2, Slave3, or Slave4.
•Select Slave1 for 100% synchronized actions.
•Select Slave2,Slave3, or Slave4
for a delayed show with all heads in the
same direction but with a delay creating a wave effect.
7. Press <ENTER>.
8. Connect the DMX input of the first slave product to the DMX output of the master.
9. Connect the DMX input of the subsequent slaves to the DMX output of the previous
slave.
10. Finish setting and connecting all the slaves.
Master:
1. Set the master to operate in either Automatic or Sound-Active mode.
2. Make the master the first product in the DMX daisy chain.
When including Intimidator Spot LED 350 products
in Master/Slave configuration
with Intimidator Spot 355 IRC products, you must observe the following:
•When the Intimidator Spot LED 350 is the master and the Intimidator Spot 355
IRC is connected as a slave, the Intimidator Spot 355 IRC must be set to DMX
mode with a starting address of 001. DO NOT set the Intimidator Spot 355 IRC
in Slave mode when an Intimidator Spot LED 350 is the master.
•The Intimidator Spot 355 IRC will not operate as the master to an Intimidator
Spot LED 350 connected as a slave.
•Configure all the slaves before connecting the master to the DMX daisy chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller
may interfere with the signals from the
master.
•Do not connect more than 31 slave units to the master.

Intimidator Spot 355 IRC User Manual Rev. 1 Page 19 of 25
IR Mode
IR mode allows the product to be controlled with an infrared remote controller. The
IRC-
6 can remotely set the product to various modes; adjust the color, speed and
sensitivity; and set the strobe.
To set the product to IR mode, do the following:
1. Make sure the product is plugged into a power source and not connected to a DMX
cable.
2. Press <MENU>.
3. Use <UP> or <DOWN> to choose Run Mode.
4. Press <ENTER>.
5. Use <UP> or <DOWN> to choose IR.
6. Press <ENTER> and the IR indicator on the front of the Intimidator Spot 355Z IRC
lights up.
IRC-6 Operation
Be sure the IRC-6 remote is pointing directly at the product and there is nothing in
between the remote and the product.
Some of the buttons on the remote work differently than what is indicated on their
labels. For example:
•<MANUAL> changes the Gobo pattern.
•<FADE> changes the color.
•<R>, <G>, <B>, <A> and <W> control other manual functions.
Please read the next section carefully.
The list below describes which features each button controls.
•<BLACKOUT> - Turns LED on and off.
•<AUTO> - Activates Auto mode. Use the <+> and <-> buttons to cycle through Auto
modes.
•<SOUND> - Activates Sound mode.
•<STROBE> - Activates the strobe. Use the <+> and <-> buttons to cycle through
strobe speeds.
•<SPEED> - Adjusts the movement speed. Use the <+> and <-> buttons to cycle
through movement speeds.
•<SENSITIVITY> - Adjusts sound sensitivity. Use the <+> and <-> buttons to cycle
through sound sensitivity levels.
•<%> - Adjusts the brightness of the LEDs. Use the <+> and <-> buttons to increase
or decrease the brightness of the LEDs.
•<MANUAL> - Changes the Gobo pattern. Use the <+> and <-> buttons to scroll
through the GOBO options.
•<FADE> Changes the color. Use the <+> and <-> buttons to scroll through the color
options.
•<R> - Activates color wheel rotation control. Use the <+> and <-> buttons to
increase or decrease rotation speed.
•<G> - Activates Gobo wheel rotation control. Use the <+> and <-> buttons to
increase or decrease rotation speed.
•<B> - Activates color and Gobo auto mode, independent from movement.
•<A> - Activates pan and tilt control. Press <A> to toggle pan and tilt, and use the
<+> and <-> buttons to increase or decrease pan or tilt values.
•<W> - Activates prism control. Use the <+> and <-> buttons to set prism value,
0–15 for off, 16–255 for on.
•<+> - Increases values for controls as described above.
•<-> - Decreases values for controls as described above.
•<0>–<9> - Activates specific Auto modes. Can be used as a shortcut for the
combination of the <AUTO> button and the <+> and <-> buttons.
•<UV> or <P> - Adjusts the focus.

Page 20 of 25 Intimidator Spot 355 IRC User Manual Rev. 1
Zero Adjust
Mode
The Intimidator Spot 355 IRC contains a passcode-protected mode that
allows you to
calibrate and adjust several of the product’s operating parameters.
To access this mode, do the following:
1. Press and hold <MENU>for at least 10 seconds.
2. Use <UP> and <DOWN> to enter the passcode: 2323.
3. Press <ENTER>.
In this mode there are several options for adjustment:
Parameter Default Description
PAN 128 Manually adjust the starting pan angle
TILT 095 Manually adjust the starting tilt angle
GOBO 120 Manually adjust the gobo wheel starting position
GOBOR 128 Manually adjust the gobo starting position
COLOR 128 Manually adjust the color wheel starting position
PRISM 128 Manually adjust the prism starting position
FOCUS 128 Manually adjust the focus starting position
LED 000 Manually adjust the starting brightness of the LED