Chiayo DWR-2410 User manual

Operation manual
CHIAYO ELECTRONICS CO., LTD.
DWR-2410 / DWR-2400
Detachable Antenna Digital Receiver
CH
GRP F REQ CH .
RF AF
MHz
0 7 9
2480
DW R - 24 1 0 Digital Wireless Receiver

1
DWR-2410 / DWR-2400 Detachable Antenna Digital Receiver
Detachable Antenna Dual Channel Digital Receiver
Thank you for choosing CHIAYO digital wireless microphone system!
For more details, please take a few moments to read this operating manual for thorough
understanding of the function and operation of both transmitter and receiver.
In the box
or
DWR-2410/2400 receiver
one transmitter
(handheld / beltpack)
DWR-2400 two antennas
DWR-2410 one antenna
audio cable
switching adaptor
operation manual
** Remark: The above specifications are subject to change without prior notice.
Parts and functions
1. Power switch
2. LCD
3. Synchronization button
4.MENU/DOWN button
5.MENU/UP button
6.SET button
7.Volume control
8.Antenna B (BNC) for DWR-2400
9.Balanced audio output
10.Unbalanced audio output
11.Antenna A (BNC) for DWR-2400
Antenna (BNC) for DWR-2410
12.DC input
CH
GRP FREQ CH.
RF AF
MHz
07 9
24 8 0
DWR -2 4 1 0 DigitalWirelessReceiver
S
D
R
-
590
0
UH
F雙頻
道數位鎖
定
自動
對
頻自動
選
訊無線麥克風
系
統
SETSYNC MIN MAX
VOLUMEPOWER
DDiiggiittaall WWiirreelleessssRReecceeiivveerrDDWWRR--22441100
2
C H
GRP FREQ CH.
RF AF
MHz
079
2480
1 3 4 5 6 7
AN T. B AN T. A DC IN
12 ~15 V
LIN E OUTMIC O UT
1.G
2.
3.
8910 11 12

2
Instructions
Changing CHANNEL / FREQUENCY
1 Press-release ▲(UP) or ▼(DOWN) button until the below channel icon
appears.
2 Press and hold SET button until the channel number flashes to denote readiness for
setting.
3 Press-release ▲(UP) or ▼(DOWN) button to select a new channel.
4 After a channel is chosen, press SET button to save the setting.
CH.
SET
SYNC
CH
CH.
RF AF
MHz
00 6
2407
SETSYNC
CH
CH.
RF AF
MHz
00 6
2407
SET
SYNC
CH
CH.
RF AF
MHz
03 6
2437
SETSYNC

3
DWR-2410 / DWR-2400 Detachable Antenna Digital Receiver
Detachable Antenna Dual Channel Digital Receiver
CHANNEL scanning
For an interference- free operation, a cleaner channel might be necessary if the current one
receives too much interference. Before scanning, the transmitter must be switched off.
To operate the scanning:
1 Press-release ▲(UP) or ▼(DOWN) button until the LCD displays SER000 and below
frequency icon appears.
2 Press and hold SET button until SER000 flashes to denote readiness for setting.
3 Press-release ▲(UP) or ▼(DOWN) button to find and locate a clear, interference- free
channel.
4 After a channel is chosen, press SET button to save the setting.
FREQ
SET
SYNC
CH
RF AF
03 6
SER000
FREQ
SETSYNC
CH
RF AF
03 6
SER000
SET
SYNC
CH
RF AF
03 6
SER042
SETSYNC

4
Instructions
CHANNEL SYNCHRONIZING of the receiver and transmitter
1 Press and hold the transmitter’s synchronizing button until LINK flashes on the LCD.
2 Press and hold the receiver’s SYNC button until the frequency icon appears.
After successful channel synchronizing, this icon will disappear automatically.
C H : 0 0 0
L I N K
FREQ
SETSYNC
CH
FREQ CH.
RF AF
MHz
00 6
2407

5
DWR-2410 / DWR-2400 Detachable Antenna Digital Receiver
Detachable Antenna Dual Channel Digital Receiver
CHANNEL GROUP setting
GROUP CH081 includes 81 selectable frequencies from CH1 to CH81.
GROUP CH189 includes 189 selectable frequencies from CH1 to CH189.
1 Press-release ▲(UP) or ▼(DOWN) button until the below group icon appears.
2 Press and hold SET button until the group number and the icon flash to denote
readiness for setting.
3 Press-release ▲(UP) or ▼(DOWN) button to choose a channel group.
4 After a group is chosen, press SET button to save the setting.
Rack mounting
The receiver can be cabinet-mounted by either one or two units. If only one receiver is to be
mounted, an optional kit is available and it's installed as shown in Fig 1. If two receivers are to
be mounted, they can be assembled by another kit and installed as shown in Fig 2.
GRP
SET
SYNC
CH
GRP
RF AF
036
CH08 1
GRP
SETSYNC
CH
GRP
RF AF
036
CH08 1
SET
SYNC
CH
GRP
RF AF
036
CH 1 89
SETSYNC

6
Instructions
Audio output connection
Balanced output: XLR connector provides balanced audio output signal from this jack to the
mixer/amplifier. Use an audio output cable with “XLR” or “Cannon” connector, connect one
end to the balanced output jack of the receiver, and the other end to the “MIC IN” jack of the
mixer/ amplifier.
Unbalanced output: ¼” PHONE PLUG connector provides unbalanced audio output signal
from this jack to the mixer/amplifier. Use an audio output cable with ¼” PHONE PLUG
connectors. Connect one end from the unbalanced output jack of the receiver, and the other
end to the “LINE IN” jack of the mixer/ amplifier.
MIC IN
LINE IN
Receiver installationFor best operation, the receiver should be at least 1m above the
ground and 1m away from a wall or metal surface to minimize
reflections. The transmitter should also be at least 1m away from a wall
or metal surface to minimize reflections. The transmitter should also be
at least 1m away from the receiver. Keep antennas away from noise
source such as motors, automobiles, neon light as well as large metal
objects.
AN T. B AN T. A DC IN
12 ~1 5 V
LI NE OU TMI C OU T
1.G
2.
3.
AN T. B AN T. A DC IN
12 ~1 5 V
LI N E OUTMI C OUT
1.G
2.
3.
Fig 1: Rack mount of one receiver
Fig 2: Rack mount of two receivers
1m 1m
1m

Detachable Antenna Dual Channel Digital Receiver
CHIAYO ELECTRONICS CO.,LTD.
Http://www.chiayo.com.tw｜Email: [e-mail]
Office: 30, Lane 27, Section 4, Jen-Ai Road, Taipei 10685, Taiwan
Tel: [phone]｜Fax: [phone]
Factory: 88, Chung-Hsiao Street 2, Chiayi 60080, Taiwan
Tel: [phone]｜Fax: [phone]