Childcare 017000 User manual

IMPORTANT:
RETAIN FOR FUTURE REFERENCE,
READ CAREFULLY
Childcare
Stroller Board “Black”
Model # 017000

2
• For use with one child at least 2 years of age and a maximum weight of 20kgs.
• This Stroller Board suits most strollers with rear leg diameter between 3-5cm.
• Child must hold on to the stroller handle at all times while occupying the stroller board.
• Caregiver must have hands on the stroller handle at all times while child is occupying the stroller board.
• DO NOT make sharp turns or walk at excessive speeds with child on stroller board.
• Stroller board MUST be properly secured to the stroller.
• ENSURE your child is always standing with both feet on the centre portion of the stroller board.
• NEVER allow child to sit on the stroller board.
• DO NOT allow child to play with or stand on the stroller board without adult supervision.
•The child MUST be supervised and the stroller brake engaged when stepping onto and off the stroller board.
• DO NOT allow child to stand on the stroller board when maneuvering the stroller on steps,over curbs or on
rough or irregular surfaces that could cause the child to lose balance.
• Keep child away from all obstructions on the side of the stroller while on the stroller board.
• Keep hands and feet clear of wheels at all times.
• Child MUST be wearing footwear at all times when standing on the stroller board.
• DO NOT allow child to stand on the stroller board when not attached to the stroller.
• ENSURE the brake is accessible and functional after installation of the stroller board.
• Use caution when stroller board platform is wet or covered with any debris to prevent child from slipping.
• To avoid injury from tipping, DO NOT allow child to stand on stroller board unless the stroller is occupied.
Read all instructions before assembly and use of the stroller board.
Keep instructions for future use.
TO AVOID INJURY OR DEATH:
ALWAYS APPLY THE BRAKES WHENEVER THE STROLLER IS STATIONARY.
DO NOT LEAVE CHILD UNATTENDED.
ENSURE THAT ALL LOCKING DEVICESARE ENGAGED BEFORE USE.
SAFETY PRECAUTIONS
WARNING

3
Due to variations in the style and design of our products, the photographs and illustrations shown in this
instruction manual are generic,therefore product fabrics,colour and design may vary from images shown.
CNP Brands reserves the right to alter product specications without notice as a result of our ongoing
policy of product improvement.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Childcare Stroller Board
Congratulations on your purchase of the Childcare
Stroller Board.
This product has been designed and developed with safety,
comfort and functionality in mind. Please take the time to read
this manual carefully before using this product and keep it in a
safe place for future reference.
CONGRATULATIONS

4
ASSEMBLY CONTENTS
Check what you have received...
You have received 1 box. Please check the contents of the
box against the list below. If anything is missing, please contact
Customer Service.
InAustralia,contact CNP Brands on 1300 667 137,in New Zealand
contact Wainhouse Distribution on 0800 567 5000.
Supplied loose in box:
x 1
x 1
x 1
x 1
x 1
x 1
x 1
Attachment
Brackets
Attachment Strap
Thumbscrew
Wheels
Extension Arms
Attachment
straps
Storage Strap
There are no accessories recommended for use with this Childcare Stroller board.
Stroller Board

5
ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Wheels...
1Place Stroller Board face down.
Push and hold wheel release button whilst
inserting Wheel into mounting hole.
Release wheel release button to secure.
Repeat for the second wheel.
1a.
1b.
1c.
1d.
To assemble Extension Arms...
1Loosen thumbscrews.1a.

6
ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Extension Arms Continued...
To install on the Stroller...
1
1
Ensuring the mounting post is facing away from the
Stroller Board,insert the Extension Arm into the
Stroller Board.
Pull apart the attachment straps and wrap them
around the rear leg of the stroller frame at the
lowest possible point.
Slightly tighten the thumbscrew until the mounting
arm is held in the Stroller Board slot.
Adjust the horizontal slider on the Extension Arm
to the shortest possible position,as close to the back
of the stroller as possible.
Repeat for the second Extension Arm.
1b.
1a.
1c.
1d.
1e.
ENSURE: the straps and bracket does not interfere with the
operation of the brake or any other moving parts.

7
ASSEMBLY / OPERATING INSTRUCTIONS
To install on the Stroller Continued...
1Align the teeth of the two straps and feed the
spindle end through the Attachment Bracket until
the strap spindle comes through the back of the
Attachment Bracket.
Secure the Attachment Bracket by screwing the
Attachment Strap Thumbscrew onto the strap
spindle until fully tightened and secure.
Repeat steps 1a-1c for the remaining Attachment
Strap and Attachment Bracket.
Flip Stroller Board and align Extension Arms with the
Attachment Brackets on the rear of the Stroller.
Ensure the mounting posts of the Extension Arms
align with the mounting slot on the assembled
Attachment Brackets.
If necessary,adjust the width of the Extension Arms
in or out of the Stroller Board to ensure the correct
alignment.
Attach the Extension Arms to the Attachment
Brackets by pushing the mountings posts down and
into the mounting slots until they lock in and are
secure.
1b.
1c.
1d.
1e.
1f.
1g.
PLEASE NOTE!
If the Attachment Bracket is still not tight on the Stroller rear leg
after assembly,please undo the Strap Thumbscrew and remove
the Attachment Strap.
Take scissors and shorten the straps using the below formula.
Repeat for the second attachment strap. Ensure all straps are cut
to the same length.
Re-t straps and attachment bracket, ensuring the bracket is tight
on the Rear Stroller Leg and does not move.
Please take care when performing this step to ensure the straps
are not cut too short and are not able to be assembled correctly.
Formula for shortening straps:
Measure the circumference of the Stroller Rear Leg. Subtract
this number by 12, then divide by 2. (Example: If your stroller leg
circumference is 9cm, 12-9=3. Divided by 2=1.5.You will need to
cut off 1.5cm from both sides of the attachment strap.

8
ASSEMBLY / OPERATING INSTRUCTIONS
To store the Stroller Board...
1Attach the Storage Strap to the handle of your Stroller
by wrapping the webbing around the handle and
securing with the buckle.
Raise the rear of the Stroller Board up toward the
handle and secure by inserting the Storage Strap
Clip into the rear of the Stroller board.
1a.
1b.
The stroller board is now ready for use.
To install on the Stroller Continued...
1Fully tighten the thumbscrews for the Extension Arms
until secure.
Ensure the Stroller Board is sitting level and both
Wheels are touching the oor.
If adjustment is required, press and hold both of the
Board Adjustment Buttons and lift or lower to correct
position.Release buttons to secure.
1h.
1i.
ENSURE: all thumbscrews are tight and secure before use.
ENSURE: all components are assembled and secured correctly
before use.

9
ASSEMBLY / OPERATING INSTRUCTIONS
To store the Stroller Board Continued...
To remove Stroller Board...
1
1
Tighten webbing strap so that the Stroller Board
is stored in the most upright position.
To remove Stroller Board from Attachment
Bracket,slide locking button on top of
Attachment Bracket down whilst pulling
Extension Arm mounting posts up and out of
Attachment Bracket.
1c.
1a.

10
HOW TO CARE FOR YOUR CHILDCARE STROLLER BOARD
Cleaning
Maintenance
To ensure the long-lasting use of your stroller board, dry it with a soft
absorbent cloth after use in rainy weather. Use a damp cloth with warm
water to clean if required. Do not use abrasive cleaners.
Check stroller board regularly to ensure that locking devices and
components are secure and working properly.Alwayscheck parts regularly
for tightness of screws, nuts and other fasteners – tighten or replace if
required.To maintain the safety of your stroller board, seek prompt repairs
for bent, torn, worn or broken parts. Use only those parts and accessories
approved by CNP Brands.
If you have any difculties in assembling the stroller board,please contact
our Service Department. In Australia, contact CNP Brands on 1300 667
137, in New Zealand contact Wainhouse Distribution on 0800 567 5000.
Warranty
For all warranty terms and conditions, please visit cnpbrands.com.au

11
ABOUT US
About CNP Brands
Currently,CNP Brands boasts one of the most diverse brand portfolios
with a combination of company owned brands and distribution
agreements.
Our own brands, including Childcare, have gone from strength to
strength in recent years. Childcare, and our premium brand bebe
care, demonstrate our commitment to quality and continuing
investment in product development.

Distributed in Australia by CNP Brands
82 Maribyrnong Street, Footscray,VIC, 3011
Customer Service 1300 667 137
W: www.cnpbrands.com.au
E: [e-mail]
F: www.facebook.com/CNPBrands
I: @cnp_baby
Distributed in New Zealand by Wainhouse
Distribution
2-6 Argyle St, Morningside,
PO Box 41-014,
St Lukes,Auckland, New Zealand
Customer Service: 0800 567 5000
E: [e-mail]