chinavasion CVSN-G672 User manual
F:,5€
F.*i11
ffi
Lr-.:
ffi
ffi&
5;D run
Operation lnstruction
rc#
.i'1;,1ffi ffi
,:*tiiil.:i-l.tl ffi
r:*
ffi#
l,al
Thank you for chocsing our products,for your better experience
of the 3D printer pen. Firstly,please read this manual carefeully.
Pen Structure input hole
wire loading hole
temperature controllel wire mloading button
speed conlxoller
wire feeding button
all in one heating nozle
Warning!!!!
This dwice is suitable fm children ovs 8 years old and adult me. chil&en should ue it mdtr
the tutelage ofadult.
The painting pen nib md the nm m ae dmgmrm high t€ryemtue re4 the highest
tmpffiture cm rcach 230"do not touch tle nib with hands or touch othm objrcts with the nib.
Do not block the wire loading hole with forcign body.
Do not re non-official power adaptor from othrconpmy.
Do not ue nm-official coroumable mmerial ftom other oryany.
This device is precision el€txonic imtn]mmt, no wara sprinHing
Keep at safty place afttr 6ing to gevent ftm higfi failing or children touching.
f,eff 1
,
Operation Guide:
l.Put the power adapter AC plug into the outlet md insert the DC plug into the ipowtr
input" hole,the yellow LED tum on md the pen is started and staadby-
2. Press the "wire feeding" button, the red led tm on and the pen is mda
preheating.After 0.5-2minutm later,the red led tm to blue, prehating finished the pen
is ready to use.
3.Inserttle mnsumphble matmial into the ,wire l.adinghole'wtichis atthe endofthepa aofta
hmd keep on presing the'wire feeding, buttorq the mahrial will be lmdedbyhdft_in motor.Wait
rhm is plastic liquid come out ftom the nib norel ,the maleriat loading is srcceed
4.Painting.(The speed confoller cm adjut the spray mout according the moving
speed, no need to use both hmds )
5.Do not touching the nozzle md heating parts duing the drawing for yor fasty.
6.The device will swith to stmdby model if stop using over 5 minutes. The
"working LED" will tm off, when use again, needpress the"wire feding" button
to resttrt,
7.When need to unloading or change the material, pleme repmr rhe sEp 2 md keep on
pressing on "wire unloading"button.
'*' : Hdirytineaftctedbyftesctiig&ry€tued@iMlEotrEde.
'**" : MustdfleM!*ial@di0gtosodbefoEl@di4dE@ial
"'*i' nnl@ding6e@erialaftE@hEiehietty@dod.
3Dpaintingpm poweradaptor consumable material
Simple fault remove chart:
Ifyou meet follw faultBlease reference the chart.
Fault appe@ce Fault re6on Fault reslvenl
Power led Dot m otr
Powq adapter or plug fault R@ir or chdge power adPatel
Mainboard fault Repair or choge the min boud
Oudet prcbld
The trozzle not spritrkle
Nozle blocked Chmge the haing nozle
T@pl€atu€ not high etrough Chage the haiag nozle ot adjBt temprcatue
No heating Chage the hating nozle or chok the mainbord
The ged bib lhe matdial wift Unlodiog cla tte gw ad cur 6e d@ag€d mtoial
Mauial reloading failw Ud@ding aDd cu the wire md 6d load again
Mainbodd problm Repair or chage tfre min boad
Not heating The heater d@ged Ctage the haring dozle
Specification:
Output material type:fused deposition modeling
Molding method: 3D modeling
Printing area:unlimited
Sprinkle speed: adjustable
Heating tempreature: 160o-230o adjustable
Power input:12V 3A
Nozzle diameter: 0.4-0.7mm
