CHN SMART SMART HOME Series User manual

[CS-8651/CS-8652/CS-8653]
SMART SWITCH
SMART HOME SERIES

User Manual of Smart Switch
(Single-wire)
I Instruction
Thank you for choosing the smart switch to control your
home lighting. It easily turn the lighting to remote control
ones. You will never feel so convenient when use the
wireless smart switch. For better use the product, please
read the user manual clearly.
II Features
Single wire technology, no need neutral wire
RF wireless technology
Low power circuit design
High-power magnetic latching relay used
Touch/Gentle touch button
Millions of different learning codes
Particular receiving circuit design, no interruption
Different series and models to select
--1--

III Technical Data
1. Working voltage: AC220V±10% 50/60Hz
2. Load power:
1-gang: 15~800W
2-gang: 1st gang: 80~800W, 2nd gang: 9~1500W
3-gang: 1st gang: 80~800W, 2nd/3rd gang: 9~1500W
(For inductive or soluble load like fluorescent or LED
lamp, the power should be dropped to 50%~30%)
3. Standby power: <0.2W
4. Frequency: 433.92MHz
5. Wireless distance: 50m (in the open air)
6. Connection: Single wire
7. Environment temp.: -10°C~+50°C
IV Installation
The switch is designed for indoor use. As we are using
single-wire Technology, no neutral wire is required to the
switch, while connected to the lamp, the lamp connects
to neutral wire.
Note: Please do not connect both live and neutral wire
to the switch.
--2--

1) Installation
2) Wire connection
--3--
L
N
Load
Wires
Φ≤4mm
Single or multiple copper
L3L2L1L
Distance: 60mm
Screws
WallOpen the panel

V Pairing Method
When you use the switch at first time, the switch just can
be switched on/off manually, you should do the pairing
to the remote controller first as the below step:
Single ON/OFF:
Power off the lamp first. Press the button on the
switch for 5 sec. Then the lamp turns “ON”, press the
button on remote controller in the coming 5 sec. The
lamp flickers twice that means the Single ON/OFF
function setting is successful. Press the button again
to quit pairing.
All-OFF:
Power off the lamp first. Press the button on the
switch for 10 sec. Then the lamp turns “ON-OFF”,
press the “OFF” button on the remote controller in the
coming 5 sec. The lamp flickers twice that means the
All-OFF function setting is successful. Press the
button again to quit pairing.
All-ON:
Power off the lamp first. Press the button on the
switch for 15 sec. Then the lamp turns “ON-OFF-ON”,
--4--

press the “ON” button on the remote controller in the
coming 5 sec. The lamp flickers twice that means All-
ON function setting is successful. Press the button
again to quit pairing.
Delete:
Power off the lamp first. Press the button on the
switch for 20 sec. Then the lamp turns “ON-OFF-ON-
OFF” that means all the paired remote controllers with
this button are deleted.
Tips
1) If you want to add a new remote controller, please do
the pairing as above pairing settings.
2) Each button on the switch can pair 20 groups of
codes. when pair 21st, the first one will be covered.
3) If you pair one button which has already paired, it will
quit pairing settings.
4) The remote controllers can be paired continuously
while in pairing setting if the time is not over 5 sec
after last pairing.
5) All the buttons should be paired to ON/OFF button to
realize All-ON/OFF function with the remote controller.
--5--

Note: all the buttons on remote controller has same
function to pair control function, i.e. each button can
be paired as single on/off, all-on, all-off and scene
control.
VI Operation
1. Single ON/OFF: Press the button on remote
controller, the lamp turns on, press the button again,
the lamp turns off.
2. All ON: Press “ON” button on the remote controller, all
the lamps (paired All-ON function) turns on.
3. All OFF: Press “OFF” button on the remote controller,
all the lamps (paired All-OFF function) turns off.
VII Scene Control Settings
Scene control means that you press one remote control
button, it launches a group of lamps on or off. Such as
dinner, sleep, home theater, going out etc. The settings
method as below:
1. Make sure the scene you want to set, including which
lamps will be ON, which lamps will be OFF.
--6--

2. Pair the All-ON function of the lamps which will be on
to the scene button and pair the All-OFF function of
the other lamps which will be off to the scene key.
According to the above method to pair all the lamps to
the scene button, then press the button, they will turn to
the status preset no matter what they are.
VIII Notice
1) If the remote distance get nearer, and LED indicator
get dark, please change the battery in time.
2) When the electric is powered on, the default status of
the switch is off.
3) The switch is not suitable for inductive fluorescent. if
used for fluorescent or LED lamp, the power should
be dropped to 50%~30%.
IX FAQ
1. Power on, but the switch has no reaction:
1) Check whether the connection wire is correct.
2) Check whether the lamp is well.
--7--

3) Check whether the power or voltage is normal.
2. Switch panel works well, but controller has no action:
1) Check whether the switch and controller are paired.
They are not paired when first use.
2) Check whether the controller is defective, and the
battery.
3. No operation both on switch and controller, but the
lamp turns on:
Maybe this gang also paired to another controller.
Clear the pairing of this gang, and re-pair to new
controller.
X Packing List
1. Smart switch: 1pc
2. User manual: 1pc
3. Screws: 2pcs
--8--

Qualification Certificate
QC no.
Model:
Date:
Memo: