Chore-Time Turbo-Cool Specifications

Turbo-Cool™
6” Recirculating Evaporative Cooling
Installation & Operator’s Instruction Manual
MV1438COctober 1997

2
Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
Chore-Time Warranty
Chore-Time Equipmentwarrants each new product manufactured by it to be free from defects in material
or workmanship for one year from the date of initial installation by the original purchaser. If such a defect
is found by Chore-Time to exist within the one year period, Chore-Time will, at its option, (a) repair or
replace such product free of charge, F.O.B. the factory of manufacture, or (b) refund to the original
purchaser the original purchase price, in lieu of such repair or replacement.
Conditions and limitations:
1. Theproduct mustbe installedand operatedin accordancewith instructionspublished byChore-Time
or warranty will be void.
2. Warranty is void if all components of a system are not supplied by Chore-Time.
3. This product must be purchased from and installed by an authorized Chore-Time dealer or certified
representative thereof, or the warranty will be void.
4. Malfunctions or failure resulting from misuse, abuse, negligence, alteration, accident, or lack of
proper maintenance shall not be considered defects under this warranty.
5. This warranty applies only to systems for the care of poultry and livestock. Other applications in
industry or commerce are not covered by this warranty.
Chore-Timeshall not be liable for any Consequentialor SpecialDamagewhich any purchaser may suffer
or claim to have suffered as a result of any defect in the product. “Consequential” or “Special Damages”
as used herein include, but are not limited to, lost or damaged products or goods, costs of transportation,
lost sales, lost orders, lost income, increased overhead, labor and incidental costs and operational
inefficiencies.
THIS WARRANTY CONSTITUTES CHORE-TIME’S ENTIRE AND SOLE WARRANTY AND
CHORE-TIME EXPRESSLY DISCLAIMS ANY AND ALL OTHER WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, EXPRESS AND IMPLIED WARRANTIES AS TO MERCHANTABILITY,
FITNESS FOR PARTICULAR PURPOSE SOLD AND DESCRIPTION OR QUALITY OF THE
PRODUCT FURNISHED HEREUNDER.
Any exceptions to this warranty must be authorized in writing by an officer of the company. Chore-Time
reserves the right to change models and specifications at any time without notice or obligation to improve
previous models.
CHORE-TIME EQUIPMENT, A Division of CTB, Inc.
P.O. Box 2000
Milford, Indiana 46542-2000 U.S.A.

Table of Contents
Topic Page User*
*Legend: C = Customer (end user), D = Distributor (sales), I - Installer of equipment
Chore-Time Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2C,D
Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4C,D
Distributor and Installer Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4C,D,I
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5C,I
Safety–Alert Symbol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5C,I
Signal Words. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5C,I
DANGER: Electrical Hazard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5C,I
Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6I
Tools Required for Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6I
Planning Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6I
Framing Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7I
Evaporative Cooling System Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9I
Splash Plate and Pipe Hanger Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9I
Trough Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9I
End Panel Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 I
Pad Support Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 I
Distribution Pipe Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 I
Sump Assembly Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 I
Sump Components Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 I
Evaporative Cooling Pan and Cover Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 I
System Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 C,I
System Operation & Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 C
Part Listings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 C,I
End Kit (Part No. 38612) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 C,I
Distribution Kit (Part No. 38679-5* & 38679-20*). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 C,I
End Panels Kit (Part No. 38676) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 C,I
Miscellaneous Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 C,I

4
Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
Support Information
The Turbo-Cool 6” Recirculating Evaporative Cooling System is designed to help cool livestock and
poultry houses. The system is shipped unassembled. Using this equipment for any other purpose or in a way
not within the operating recommendations specified in this manual will void the warranty and may cause
personal injury.
This manual is designed to provide comprehensive planning, installation, operation, and parts listing
information. The Table of Contents provides a convenient overview of the information in this manual. The
Table of Contents also specifies which pages contain information for the sales personnel, installer, and
consumer (end user).
IMPORTANT: CE stands for certified Europe. It is a standard which
equipment must meet or exceed in ordered to be sold in Europe. CE
provides a benchmark for safety and manufacturing issues. CE is
required only on equipment sold in Europe.
Chore-Time Equipment recognizes CE Mark and pursues compliance
in all applicable products. Fill in the CE-Mark serial number in the
blank space provided for future reference.
(CE-mark serial number)
Distributor and Installer Information
Please fill in the following information about your Product.
Keep this manual in a clean, dry place for future reference.
Distributor’s Name___________________________________________________
Distributor’s Address ________________________________________________
Distributor’s Phone _______________________ Date of Purchase ___________
Installer’s Name_____________________________________________________
Installer’s Address___________________________________________________
Installer’s Phone _______________________ Date of Installation ___________
System Specifications________________________________________________
___________________________________________________________________

Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
5
Safety Information
Caution, Warning and Danger Decals have been placed on the equipment to warn of potentially
dangerous situations. Care should be taken to keep this information intact and easy to read at all times.
Replace missing or damaged safety signs.
Using the equipment for purposes other than specified in this manual may cause personal injury and or
damage to the equipment.
Safety–Alert Symbol
This is a safety–alert symbol. When you see this symbol on your equipment, be alert to
the potential for personal injury. This equipment is designed to be installed and operated
as safely as possible...however, hazards do exist.
Signal Words
Signal words are used in conjunction with the safety–alert symbol to
identify the severity of the warning.
DANGER........... indicates an imminently hazardous situation
which, if not avoided, WILL result in death
or serious injury.
WARNING........ indicates a potentially hazardous situation
which, if not avoided, COULD result in
death or serious injury.
CAUTION.......... indicates a hazardous situation which, if not
avoided, MAY result in minor or moderate
injury.
DANGER: Electrical Hazard
Disconnect electrical power before inspecting or servicing
equipment unless maintenance instructions specifically state
otherwise.
Ground all electrical equipment for safety.
All electrical wiring must be done by a qualified electrician in
accordance with local and national electric codes.
Ground all non-current carrying metal parts to guard against
electrical shock.
With the exception of motor overload protection, electrical
disconnects and over current protection are not supplied with the
equipment.
DANGER
WARNING
CAUTION

6
Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
Technical Information
Required water supply: 2.0 gpm per 100 sq. ft. of pad at 100°F 20% Relative
Humidity
Supply water pressure: 30 - 45 psi
Water Quality: 6 - 9 PH, salt concentration less than 40,000 ppm
Air Speed Through Pad: Munters Celdek & Glacier Core 45°/15° pad-- 425 cfm/sq. ft.
Munters Mi-T-Cool-- 500 cfm/sq. ft.
Required electrical service: 230 V. 1-Phs, 50/60 Hz. , 4.8 amp
Maximum pad length per pump: 50’ at 60 Hz, 40’ at 50 Hz.
Important
Chore-Time Equipment strongly recommends that a good alarm system should be installed in
confinement buildings to warn of power failure and high temperature.
Chore-Time Equipment also recommends that an alternate power source be available for
confinement buildings in case of power failure.
Tools Required for Installation
Socket Wrench • 1/2” & 5/16” Sockets • Drill and 5/16” Drill Bit • 1/2” Wrench • Teflon Tape
PVC Cement • Utility Knife • Saw
Planning Information
Figure 1 shows recommended Evaporative Cooling Pads vs. Tunnel Fan locations.
Figure 1. Possible Evaporative Cooling System Layouts (top view)
Key Description
1Cooling Pads
2Tunnel Fans

Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
7
Framing Information
Figure 2 shows two options for installing the cooling pad relative to the tunnel
curtain and provides the required information for the Evaporative Cooling System
opening.
Notice the dimensional information included.
Frame the Pad opening using treated lumber.
1. Determine the location of the bottom stringer. See Figure 2, Item 3.
Note: The maximum slope of the opening is 1-1/2” (3.8 cm) from the inlet end to
the sump end. The sump end must be level or lower than the inlet end.
Use screws to secure the bottom stringer to the studs. The lower 2” x 6” (50 x 152
mm) Stringer must be capable of supporting 30 lbs/ft. (4.2 kg/m).
2. Snap a chalk line on the lower stringer at the locations specified in Figure 2,
Item 13. This chalk line will determine the location of the lag screws for the
Trough Supports.
3. Determine the location of the top stringer. See Figure 2, Item 8. The distance
between the top and bottom stringers should be approximately 1-1/2” (3.8 cm)
less than the height of the Evaporative Cooling Pads.
Example: for a 60” tall Evaporative Cooling Pad the distance between the stringers
would be 60” - (1-1/2”) = 58-1/2”.
Note: The slope (if any) of the top stringer must be the same as the bottom stringer.
4. Snap a chalk line on the top stringer at the locations specified in Figure2, Item
12. This chalk line will determine the location of the Splash Plate lower holes.

8
Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
Figure 2. Framing Overview Diagram
Item Description Item Description
1Curtain 10 Width of Pad Bank
210” (250 mm) Minimum Clearance 11 2” x 6” (50 x 152 mm) Bottom Stringer
315” (38 cm) Minimum Clearance 12 Pad Height plus 2-3/4” (7 cm)
430” - 36” (76 - 91 cm) Walkway 13 1-1/4” (3.2 cm)
56” (15 cm) Minimum Clearance 14 Bottom Stringer Chalk Line
62” x 6” (50 x 152 mm) Top Stringer 15 Top Stringer Chalk Line
7Studs 16 24” (61 cm) for Sump Assembly
8Pad Height less 1-1/2” (38 mm) 17 9” (23 cm) for Inlet Assembly
9 End Framing 18 7-1/2” (19.1 cm)
Sump End
Inlet End

Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
9
Evaporative Cooling System Installation
Splash Plate and Pipe Hanger Installation
Secure the Splash Plates to the upper stringer, using a 10-16x1-1/2” screw at each
end.
Note: The end holes in the Splash Plate must align with the chalk line and the end
of the first Splash Plate must be flush with the inside of the end framing. See
Figure 3.
Align the end mounting holes on the chalk line. See Figure 3.
Secure the Pipe Hangers to the stringer, through the Splash Plate, using (2) 10-
16x1-1/2” screws. The lower hole in the Pipe Hanger should align with the chalk
line on the stringer.
Hang remaining Splash Plates butting them tightly end to end. If the last Splash
Plate is too long to fit within the end framing, cut as shown in Figure 3.
Note: The Splash Plates are pre-drilled for installation and for accurate spacing
and locating the Pipe Hangers.
Figure 3. Splash Plate & Pipe Hanger Installation
Trough Installation
The Trough must be secured to the lower stringer. See the Framing Installation
section for stringer specifications.
1. Mark the Trough Support locations.
The first and last Trough Supports must be positioned flush with the inside of
the framed opening. The bolt hole should be aligned on the chalk line. See
Figure 4.
Item Description
110-16x1-1/2” Screw
2Pipe Hanger
3Splash Plate
4Upper Stringer
5Chalk Line
6 Flush with edge of end framing
7 Cut here if too long

Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
10
The next Trough Support (at the sump end) must be positioned in 10” (25 cm).
See Figure 4.
Space the remaining Trough Supports 20” (50 cm) apart.
The chalk line provides the proper vertical location of the lag screws.
2. Loosely secure the Trough Hangers, Trough Supports, and plastic washers to
the lower stringer, as shown in Figure 4, using the 5/16 x 1-1/2” stainless steel
lag screws.
Note: Leave the Trough Supports loose to allow the Trough to be installed. See
Figure 5, Step 1.
Figure 4. Trough Support and Hanger Installation
3. The Trough should extend out past the last Trough Support at the Sump
Assembly end at least 5” (12.7 cm)
The Trough should extend out past the last Trough Support at the inlet end at
least 1” (2.5 cm).
The Trough will be cut to length after the End Assembly is installed.
Roll the Trough out flat on the floor below the Trough Hangers.
4. Beginning at one end, slide one side of the Trough between the stringer and the
Trough Support. Make sure the Trough edge is up against the washer. See
Figure 5, Step 1.
Item Description Item Description
1Chalk Line 6Trough Support (Left End)
25/16 x 1-1/2” S.S. Lag Screw 7 Flush with edge of end framing
3Nylon Washer 8Trough Support (Right End)
4Bottom Stringer 910” (25 cm)
5Hanger 10 20” (50 cm)

Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
11
5. Tighten the lag screw to secure the Trough in place against the stringer. See
Figure 5, Step 2. Repeat steps 4 - 5 for all Trough Supports.
6. Form a loop, using the Trough and Trough Hangers, as shown in Figure 5,
Step 2.
7. Use the hole in the Trough Support and Trough Hanger as a guide to drill or
punch a 5/16” (8 mm) hole in the Trough.
8. Fasten the Trough and Trough Hanger to the Trough Support using the 5/16-18
x 1/2” bolt and 5/16” hex nut. Repeat steps 6 - 8 for each Trough Support.
9. Wipe the inside of the Trough at the Trough End Assembly location to remove
debris that may prevent proper sealing.
Position the End Assembly against the outside of the Trough Support at the inlet
end of the Trough. See Figures 6 & 7.
Position the Adjustable Clamp directly over the Trough End Assembly,
orienting as shown in Figure 6, and tighten firmly.
Figure 5.Trough Installation (end view)
Item Description
1Trough Support
2Trough
3Insert Trough between the Trough Support and the
stringer.
4Trough Hanger
55/16” x 1-1/2” Lag Screw
6Wrap Trough and Trough Support to form loop.
7 Drill or punch a 5/16” (8 mm) hole through Trough.
Step 1 Step 2 Step 3

Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
12
Figure 6. Trough End Assembly Installation
10. Connect the outlet end of the Water Level Regulator to the Trough End
Assembly. See Figure 7.
Figure 7. Inlet Installation
Item Description
13/4” Garden Hose (not supplied)
2Water Level Regulator
3Trough End Assembly
4Trough Support
Step 1 Step 2
Note: The Trough Support and Trough Hangers are not shown for clarity.

Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
13
End Panel Installation
The End Panels should be installed flush with the inside of the opening (at both
ends).
1. Locate the top mounting hole (in the flange of the Upper End Panels) on the
chalk line. This will properly align the hole for the Distribution Pipe with the
Pipe Hangers. See Figure 8. Secure the Upper End Panels to the top stringer
using the 10-16x1-1/2” Screws, as shown in Figure 8.
2. The Lower End Panels should overlap on the outside of the Upper End Panels
to provide proper watershed.
3. Align mounting holes in the upper and lower end panels and secure the end
panels to the frame using the 10-16x1-1/2” Screws.
Figure 8. End Panel Installation
Item Description
1Chalk Line on top stringer
210-16 x 1-1/2” S.S. Screw
3Upper End Panel
4Lower End Panel

14
Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
Pad Support Installation
Set the Pad Supports on the Trough Hangers, as shown in Figure 9. The Pad Supports should
extend to both End Panels.
Overlap the Pad Supports as required, depending on the Trough length.
Note: Sump components and End Panels not shown for clarity.
Figure 9. Pad Support Installation
Distribution Pipe Installation
1. Set a Distribution Pipe on the Pipe Hangers above the inlet end of the Trough.
Note: The belled end must be toward the sump end.
2. Assemble the Distribution Pipes by inserting the straight end of one pipe into the belled end of
another. It is not necessary to glue the Distribution Pipes together.
IMPORTANT: The spray holes, in the Distribution Pipes, MUST all be aligned and
pointing straight up.
3. Slide the straight end, of the Distribution Pipe directly above the Sump Base, through the End
Panel (since the bell will not fit through the End Panel hole) and into the bell of the next
Distribution Pipe.
4. Verify that the spray holes are in alignment, then install a 10-16 x 1/2” S.S. Screw at each bell
to secure the pipes together.
5. Sump End: The distance from the End Panel to the end of the pipe bell should be
approximately 10-1/2” (26.6 cm).
Inlet End: The Pipe should extend past the inlet end End Panel.
6. Install a 10-16 x 1/2” S.S. Screw in each spray hole that falls outside the End Panels (at either
Item Description
1 Pad Support
25” (12.7 cm) Minimum at
Sump End
3Trough
4Overlap 1” (2.5 cm) Minimum

Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
15
end).
7. Insert at 2” Mechanical Gripper Plug in the end of the Distribution Pipe. See
Figure 10.
Figure 10. Distribution Pipe Installation
Sump Assembly Installation
1. Trim the Trough at the Sump end to 5” (12.7 cm) of overhang. Position the
Sump Base at the sump end of the Trough, as shown in Figure11. The Sump
Base should set directly against the end Trough Support.
2. Wipe the inside of the Trough at the sump end to remove debris that may
prevent proper sealing.
Secure the Sump Base in the end of the Trough, using an Adjustable Clamp, as
shown in Figure 11.
Item Description
110-16 x 1/2” S.S. Screw
25’ Distribution Pipe
32” Mechanical Gripper Plug
4Framing
5Upper End Panel (R.H)
6Upper End Panel (L.H.)
7Lower End Panel (R.H.)
8Lower End Panel (L.H.)
910-1/2” (26.6 cm) Approximately

Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
16
The Sump Base must sit squarely on the floor or support surface.
3. Install the 3/4” x 4-3/4” PVC Pipe in the fitting inside the Sump Base. This
pipe serves as the overflow pipe.
Figure 11. Sump Base Installation
Sump Components Installation
Assemble the Sump Components as shown in Figure 12, beginning at the Pump.
The lengths of 1-1/2” PVC Pipe (Item #6) will vary depending on desired Valve
height, pad height, etc.
Note: The 1-1/2” PVC Tee slips inside the bell of the Distribution Pipe.
Use teflon tape (not supplied) on threads as required. Use PVC glue on slip
connections.
Plug the electrical cord into the receptacle (not supplied).
Note: Make sure the vent hose inside the electrical cord is not obstructed.
Route the 1/4” Black Bleed Off Hose to a drain for waste water. Do not run the
bleed off hose back into the sump or trough.
Item Description
13/4” Overflow Pipe
2Trough
3 Adjustable Clamp
4Sump Base
5 Sump Support (not supplied)

Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
17
Figure 12. Distribution Pipe Installation
Item Description Item Description
11-1/2” PVC Tee 81-1/2” Union PVC Valve
21-1/2” x 3/4” PVC Reducer Bushing 91-1/2” Adapter Valve
33/4” Water Bleed-Off Valve 10 1/3 H.P. 60 Hz. Pump
4Hose Barb Cap 11 Sump
51/4” Black Bleed Off Hose 12 1-1/2” Mechanical Gripper Plug
61-1/2” PVC Pipe 13 Sump Screen
7 Strainer 14 Overflow Drain

Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
18
Evaporative Cooling Pan and Cover Installation
1. Set the Evaporative Cooling Pads on the Pad Supports. See Figure 13. The top
of the Pads should be against the Splash Plate and directly below the
Distribution Pipe.
Make sure the Pads are properly oriented.
MUNTERS Pads:Refer to the directional arrows on the side of the pads.
GLACIER Pads: May have a blue stripe which indicates the top end of pads
and the air inlet side of the pads.
If no stripe is present, refer to Figure14to determine the proper pad orientation
based on the direction of the pad flutes vs. direction of incoming air flow.
Begin installing pads at either end.
Make sure the first pad is against the End Panels.
Push Pads tightly together and keep as vertical as possible.
Figure 13. Pad Installation
Item Description
1Munters Pad
2Glacier Pad

Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
19
Figure 14. Pad Orientation (cut-away view of side of Pad)
2. Set the Covers on the Pipe Hangers, as shown in Figure 15, Step 1.
3. Slide the Cover Locks onto the Pipe Hangers, as shown in Figure 15, Step 2.
4. Repeat steps 1-3 until all the Evaporative Cooling Pads are installed. The
Covers should butt end to end.
5. The Evaporative Cooling Pads may be trimmed as required using a handsaw,
to fit inside the End Panels.
Figure 15. Cover and Cover Lock Installation
Item Description
1Cover
2Distribution Pipe
3Evaporative Cooling Pad
4Cover Lock
Step 1 Step 2

Turbo-Cool 6” Recirculating Evaporative Cooling System Manual
20
6. If the last Cover is too long, trim the Cover as shown in Figure16 and overlap
it with the previous Cover. Use (2) 10-16 x 1/2” Screws to join the Covers
together.
Figure 16. Cover Trimming and Assembly
System Start-Up
1. Turn the Adjustment Knob on the Water Level Regulator clockwise to the
fully closed position. Turn on the water supply.
2. The water level adjustment knob is on the back of the Regulator near the
Chore-Time logo. To increase the water level turn the knob in the direction of
the “I” or “+”. To decrease the water level turn the knob in the direction of the
“D” or “-”. See Figure 17.
Figure 17. Water Level Regulator
3. With the pump off (i.e. unplugged), Turn the Adjustment Knob on the Water
Level Regulator Counter-clockwise to raise the water level to 1” (2.5 cm)
below the top of the overflow pipe in the sump.
Item Description
1 Required Length of last Cover
22” (5 cm)
3Cutting line
410-16 x 1/2” Screw
5Cover
Item Description
1Adjustment Knob (Water Level Regulator)