Christie 103-011100-01 User manual

Multimedia Projector
Quick Reference Guide
MODEL 103-011100-01
Use this book as a reference guide when setting up the projector.
For detailed information about installation, setup, and operation of
the projector, refer to the owner’s manual on the CD-ROM.
READ THE SAFETY INSTRUCTIONS IN THE OWNER’S MANUAL
(CD-ROM) BEFORE USING THE PROJECTOR.
EnglishDeutsch Français
Italiano Español
✽Projection lens is optional.

- 2 -
NAME OF EACH PART OF PROJECTOR
BOTTOM OF CABINET
BACK OF CABINET
HOT AIR EXHAUSTED !
Air blown from exhaust vent is hot. When
using or installing a projector, following
precautions should be taken.
●Do not put a flammable object near this vent.
●Keep rear grills at least 3.3’(1 m) away from
any object, especially heat-sensitive object.
●Do not touch this area, especially screws
and metallic parts. This area will become
hot while a projector is used.
This projector detects internal temperature
and automatically controls operating power
of Cooling Fans.
FRONT OF CABINET
LAMP COVER
ADJUSTABLE FEET
AND
FEET LOCK LATCHES
This projector is equipped with cooling fans for protection from
overheating. Pay attention to following to ensure proper ventilation
and avoid a possible risk of fire and malfunction.
●Do not cover vent slots.
●Keep side clear of any objects. Obstructions may block cooling
air.
AIR INTAKE VENTS
PROJECTION LENS
SPEAKERS
INFRARED
REMOTE RECEIVER
LENS CAP
POWER CORD
CONNECTOR
EXHAUST VENT
TERMINALS
AND CONNECTORS
TOP CONTROLS
AND INDICATORS
INFRARED
REMOTE RECEIVER
CARRYING
HANDLE
AIR INTAKE
VENT
CAUTION
Do not turn on the projector with
the lens cap attached. High
temperature from light beam may
damage the lens cap and result in
fire hazard.
(optional)
(optional)

- 3 -
English
SETTING-UP PROJECTOR
This projector uses nominal input voltages of 100-120 V or 200-240
V AC. This projector automatically selects correct input voltage. It
is designed to work with single-phase power systems having a
grounded neutral conductor. To reduce risk of electrical shock, do
not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure
of type of power supply being in use.
Connect a projector with a peripheral equipment before turning a
projector on.
CAUTION
For safety, unplug AC Power Cord when an appliance is not
used.
When this projector is connected to outlet with AC Power Cord,
an appliance is in Stand-by Mode and consumes a little electric
power.
CONNECTING AC POWER CORD
Connect AC Power Cord (supplied) to a projector.
AC outlet must be near this equipment and must
be easily accessible.
To POWER CORD
CONNECTOR on the
projector.
Projector side AC Outlet side
Ground
CAUTION
The AC Power Cord must meet the requirement of the country where you use the projector.
Confirm the AC plug type with the chart below. The proper AC Power Cord must be used.
If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.
To AC Outlet.
(120 V AC)
For Continental Europe
For U.S.A. and Canada
To AC Outlet.
(200 - 240 V AC)

- 4 -
LENS SHIFT ADJUSTMENT
Projection lens can be moved up and down with motor-driven lens shift function. This function makes it easy to
provide projected image where you want.
H3
H4
H1
H2
Highest Lens Shift Lowest Lens Shift
H1 : H2 = 6 : 1
H3 : H4 = 1 : 1
NOTE
Screen size and lens shift ratio on the above charts are standard values and they may change by positioning
conditions.
POSITIONING PROJECTOR
This projector is designed to project on a flat projection
surface.
ROOM LIGHT
Brightness in a room has a great influence on picture
quality. It is recommended to limit ambient lighting in
order to provide best image.
SCREEN
Before setting up a projector, install Projection Lens on
Projector.
1. Before installation, check where a projector is used and
prepare a suitable lens. For specifications of a Projection
Lens, contact sales dealer where you purchased a projector.
2. For installation, refer to installation manual in the optional
lens.
LENS INSTALLATION
COVER CAP
When installing the lens, remove the cover cap in the
projector.
NOTE;

- 5 -
English
ADJUSTABLE FEET
Picture tilt and projection angle can be adjusted by
rotating ADJUSTABLE FEET. Projection angle can be
adjusted to 10.5 degrees.
Lift front of a projector and pull FEET LOCK LATCHES
on both sides of a projector.
1
Release FEET LOCK LATCHES to lock ADJUSTABLE
FEET and rotate ADJUSTABLE FEET to fine tune
position and tilt.
2
To shorten ADJUSTABLE FEET, lift front of a projector
and pull and undo FEET LOCK LATCHES.
Position and keystone distortion of image can be adjusted
using Menu Operation.
3
INSTALLING PROJECTOR IN PROPER POSITION
Install the projector properly. Improper installation may reduce the lamp lifetime and cause a fire hazard.
Do not tilt the projector more than 10 degrees above and below.
Do not point the projector up to project an image.
Do not point the projector down to project an image.
Do not put the projector on either side to project an image.
NO UPWARD
NO DOWNWARD
NO SIDEWAYS
10˚
10˚
ADJUSTABLE FEET FEET LOCK
LATCHES

- 6 -
CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR
●Do not drop or bump a projector, otherwise damages or malfunctions may result.
●When carrying a projector, use a suitable carrying case.
●Do not transport a projector by using a courier or transport service in an unsuitable transport case. This
may cause damage to a projector. To transport a projector through a courier or transport service, consult
your dealer for best way.
MOVING PROJECTOR
Use Carrying Handle when moving a projector.
When moving a projector, replace lens cap and retract
feet to prevent damage to lens and cabinet.
When this projector is not in use for an extended period,
put it into case (not supplied with this projector).

- 7 -
English
S–VIDEO
R–AUDIO–L
VIDEO/Y Cb/Pb Cr/Pr
VIDEO/Y Cb/Pb Cr/Pr
RESET CONTROL PORT
AUDIO 1 AUDIO 2
ANALOG DIGITAL(DVI-D)
INPUT 1
INPUT 2
INPUT 3
R/C JACK
GBRH/V V
(MONO)
TERMINALS OF PROJECTOR
When controlling the projector
from a computer, connect the
computer to this connector
with a control cable.
Connect S-VIDEO
output from video
equipment to this
jack.
Connect an audio output
from video equipment to
these jacks.
When the audio output is
monaural, connect it to
L (MONO) jack.
CONTROL PORT CONNECTOR
AUDIO INPUT JACKS VIDEO INPUT JACKS S-VIDEO INPUT JACK
Connect composite video
output from video equipment
to VIDEO/Y jack or connect
component video outputs to
VIDEO/Y, Cb/Pb and Cr/Pr
jacks.
Connect computer output
(Analog HDB 15 pin type)
to this terminal.
INPUT TERMINAL (ANALOG)
This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on
pages 12 to 14 and connect properly.
This projector uses a micro processor
to control this unit, and occasionally,
this micro processor may malfunction
and need to be reset. This can be
done by pressing RESET button with a
pen, which will shut down and restart
unit. Do not use RESET function
excessively.
RESET BUTTON
Connect component video
output (Y, Cb, Cr or Y, Pb, Pr)
from video equipment to
VIDEO/Y, Cb/Pb and Cr/Pr
jacks or connect computer
output {5 BNC Type (Green,
Blue, Red, Horiz. Sync and
Vert. Sync.)} from computer
to G, B, R, H/V and V jacks.
5 BNC INPUT JACKS
When using Wired/Wireless
Remote Control Unit as Wired
Remote Control, Connect
Wired Remote Control Unit to
this jack with Remote Control
Cable (not supplied).
R/C JACK
Connect an audio output
(stereo) from computer to
this jack.
Connect computer output
(Digital DVI-D type) to this
terminal.
HD (HDCP Compatible) signal
can also be connected.
INPUT TERMINAL (DIGITAL)
Connect an audio output
(stereo) from computer to
this jack.
AUDIO INPUT 1 JACK
AUDIO INPUT 2 JACK

- 8 -
S–VIDEO
R–AUDIO–L
VIDEO/Y Cb/Pb Cr/Pr
VIDEO/Y Cb/Pb Cr/Pr
RESET CONTROL PORT
AUDIO 1 AUDIO 2
ANALOG DIGITAL(DVI-D)
INPUT 1
INPUT 2
INPUT 3
R/C JACK
GBRH/V V
(MONO)
CONNECTING TO COMPUTER
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA/SXGA+/WXGA/UXGA)
Monitor Output
Desktop type Laptop type
Control Cable
for Serial Port
Serial portAudio Output
CONTROL
PORT
AUDIO IN 1 or 2
INPUT TERMINAL (ANALOG)
Cables used for connection (✽= Cable or adapter is not supplied with this projector.)
Audio
Cable ✽
(stereo)
• VGA Cable (HDB 15 pin)
• DVI-Digital Cable (for Single Link T.M.D.S.) ✽
• BNC Cable ✽
• Control Cable for Serial Port
• Audio Cables (Mini Plug (stereo) ) ✽
Terminals
of a Projector
Terminal
DVI-Digital
Cable ✽
Monitor Output
BNC
Cable ✽
INPUT TERMINAL (DIGITAL)
Note:
When connecting the cable, the power
cords of both the projector and the
external equipment should be
disconnected from AC outlet.
VGA Cable
Monitor Output
5 BNC (G/B/R/HV/V)

- 9 -
English
CONNECTING TO VIDEO EQUIPMENT
S–VIDEO
R–AUDIO–L
VIDEO/Y Cb/Pb Cr/Pr
VIDEO/Y Cb/Pb Cr/Pr
RESET CONTROL PORT
AUDIO 1 AUDIO 2
ANALOG DIGITAL(DVI-D)
INPUT 1
INPUT 2
INPUT 3
R/C JACK
GBRH/V V
(MONO)
Video Source (example)
Video Cassette Recorder Video Disc Player
S-VIDEO
Cable ✽
Terminals
of a Projector
S-VIDEO
Output
Cables used for connection (✽= Cable is not supplied with this projector.)
Audio Cable
(RCA x 2) ✽
AUDIO IN S-VIDEO
Y - Cb/Pb - Cr/Pr
VIDEO
Component video output equipment.
(such as DVD player or high-definition TV source.)
Composite
Video Output
Component Video
Output
(Y, Cb/Pb, Cr/Pr)
Component Video
Output
(Y, Cb/Pb, Cr/Pr)
Y - Cb/Pb - Cr/Pr
Video Cables
(RCA x 1 or
RCA x 3) ✽
BNC Cable ✽
Audio
Output
Composite
Video Output
VIDEO
• Video Cable (RCA x 1 or RCA x 3) ✽
• BNC Cable ✽
• S-VIDEO Cable ✽
• DVI-Digital Cable (for Single Link T.M.D.S.) ✽
• Audio Cable (RCA x 2) ✽
• HDB 15 pin-SCART 21 pin Cable ✽
RGB Scart
21-pin Output
HDB 15 pin-
SCART 21 pin
Cable ✽
INPUT TERMINAL (ANALOG)
Note:
When connecting the cable, the power cords of
both the projector and the external equipment
should be disconnected from AC outlet.
Digital Output
(HDCP compatible)
DVI-Digital
Cable ✽
INPUT TERMINAL
(DIGITAL)

- 10 -
ON-OFF
SELECT
COLOR M. MENU
LIGHT
I
-
INPUT
2
3
SCREEN
SCREEN
L
L
1
D.ZOOM
NO SHOW
NO SHOW
FREEZE
MUTE
MUTE
Z
ZF
F
KEYS.
I
I
INPUT IMAGE
SELECTION
KEYSTONE
FOCUSLENS ZOOM
V
O
L
U
M
E
-
V
O
L
U
M
E
+
AUTO PC
AUTO
OPERATION OF REMOTE CONTROL
LIGHT BUTTON
Lights the buttons on the remote
control for about 10 seconds.
Used to select input
source.
POWER ON-OFF BUTTON
Used to turn projector on or
off.
MENU BUTTON
Used to select MENU
operation.
INPUT BUTTON
MUTE BUTTON
Used to mute sound.
AUTO PC ADJ. BUTTON
Used to operate AUTO PC
Adjustment function.
FREEZE BUTTON
Used to freeze picture.
SELECT BUTTON
POINT (UP / DOWN / LEFT / RIGHT)
BUTTONS
Used to select an item or adjust
value in ON-SCREEN MENU.
They are also used to pan image
in DIGITAL ZOOM +/– mode.
POINT LEFT/RIGHT buttons are
also used as VOLUME +/–
buttons.
Used to execute item
selected. It is also used to
expand / compress image
in DIGITAL ZOOM mode.
COLOR M. BUTTON
Used to operate COLOR
MANAGEMENT.
Used to adjust zoom.
ZOOM BUTTON
FOCUS BUTTON
Used to adjust focus.
NO SHOW BUTTON
Used to turn picture into
black image.
D.ZOOM BUTTON
Used to select DIGITAL
ZOOM +/– mode and
resize image.
KEYSTONE BUTTON
Used to correct
keystone distortion.
IMAGE BUTTON
Used to select image
level.
WIRED REMOTE JACK
When using as Wired Remote
Control, connect Remote
Control Cable to this jack.
Battery installation is required
when using as Wired Remote
Control.
SCREEN BUTTON
Used to select screen.
LENS SHIFT BUTTON
Used to select LENS
SHIFT function.
IMAGE ADJ. BUTTON
Used to adjust image
level.