Christie CP4230 User manual

CP4230 Setup Guide
Light Hazard Addendum
This document is an addendum to the CP4230 Setup Guide (P/N: 020-100669-XX).
Light intensity hazard distance
This projector has been classified as Risk Group 3 as per the IEC 62471-5:2015 standard due to
possible hazardous optical and thermal radiation being emitted.
Warning! If not avoided, the following could result in serious injury.
• PERMANENT/TEMPORARY BLINDNESS HAZARD! No direct exposure to the beam must be
permitted. Risk Group 3 according to IEC 62471-5:2015.
• PERMANENT/TEMPORARY BLINDNESS HAZARD! Operators must control access to the beam
within the hazard distance or install the product at the height that prevents exposure of
spectators' eyes within the hazard distance. The hazard zone must be no lower than 2.5 meters
(US installations) or 2.0 meters (global installations) above any surface upon which any persons
are permitted to stand and the horizontal clearance to the hazard zone must be a minimum 1.0
meters.
• EXTREME BRIGHTNESS! Do not place reflective objects in the product light path.
The following show the zones for ocular and skin hazard distances.
• A—Hazard zone. The region of space where the projection light from the projector is above
emission limits for Risk Group 2. The light intensity may cause eye damage after a momentary
Christie CP2230 Addendum 1
020-103541-01 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

or brief exposure (before a person can avert his or her eyes away from the light source). The
light may cause skin burns to occur.
• B—Hazard distance. Operators must control access to the beam within the hazard distance or
install the product preventing potential exposure of the spectators' eyes from being in the
hazard distance.
• C—No access zone. Horizontal clearance of the no access zone must be a minimum of 1.0
meters.
• D—Vertical distance to hazard zone. The hazard zone must be no lower than 2.5 meters (US
installations) or 2.0 meters (global installations) above any surface upon which any persons
are permitted to stand.
• E—Represents the top view of the projector.
• F—Represents the side view of the projector.
Table 1: CP4230 Lenses
Lens Type Projection Lens Part Number
HB 1.25-1.45:1 108-274101-XX
1.45-1.8:1 108-275101-XX
1.8-2.4:1 108-276101-XX
2.20-3.0:1 108-277101-XX
3.0-4.3:1 108-278101-XX
4.3-6.0:1 108-279101-XX
5.5-8.5:1 108-280101-XX
1.45-2.05:1 108-335102-XX
1.6-2.4:1 108-336103-XX
1.8-3.0:1 108-337104-XX
2.15-3.6:1 108-338105-XX
1.25-1.83:1 108-342100-XX
HC 1.25-1.83:1 108-400105-XX
1.45-2.05:1 108-401106-XX
1.6-2.4:1 108-402107-XX
1.8-3.0:1 108-403108-XX
2.15-3.6:1 108-404109-XX
1.8-2.4:1 38-809052-XX
2.2-3.0:1 38-809053-XX
1.45-1.8:1 38-809061-XX
1.25-1.45:1 38-809079-XX
CP4230 Setup Guide Light Hazard Addendum
Christie CP2230 Addendum 2
020-103541-01 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

CP4230 Setup Guide Light Hazard Addendum
Christie CP2230 Addendum 3
020-103541-01 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.