Christie DHD600-G User manual

USER MANUAL
020-000648-01
G Series
DWX600-G/DHD600-G/DWU600-G

Addendum
The CD included with this printed manual contains an electronic copy in English. Please read all instructions before
using or servicing this product.
Die mit dieser gedruckten Anleitung gelieferte CD enthält eine elektronische Kopie in Deutsch. Bitte lesen Sie alle
Anweisungen, bevor Sie dieses Produkt verwenden oder warten.
Le DC fourni avec ce manuel imprimé contient une copie électronique en français. S'il vous plaît lire toutes les
instructions avant d'utiliser ou de réparer ce produit.
Il CD fornito con il manuale stampato contiene una copia elettronica in lingua italiano. Si prega di leggere tutte le
istruzioni prima di utilizzare o riparare questo prodotto.
El DC incluido con este manual impreso contiene una copia electrónica en español. Por favor, lea todas las
instrucciones antes de usar o dar servicio a este producto.

NOTICES
COPYRIGHT AND TRADEMARKS
© 2014 Christie Digital Systems USA, Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of
their respective holders.
REGULATORY
The product has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the product is operated in a commercial environment. The
product generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of the product in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at the user’s own expense.
WARNING! Changes or modications not expressly approved by Christie could void the user’s
authority to operate the product.
FOR COMMERCIAL USE ONLY - POUR USAGE COMMERCIAL UNIQUEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT
TO THE FOLLOWING 2 CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.
CET APPAREIL NUMÉRIQUE DE CLASSE A EST CONFORME AUX NORMES DÉFINIES
DANS LES RÉGLEMENTATIONS CANADIENNES SUR LES APPAREILS CAUSANT
DES INTERFÉRENCES RADIO (CANADIAN INTERFERENCE-CAUSING EQUIPMENT
REGULATIONS, ICES-003, CLASS A).
, .

GENERAL
Every effort has been made to ensure accuracy, however in some cases changes in the products
or availability could occur which may not be reected in this document. Christie reserves the right
to make changes to specications at any time without notice. Performance specications are
typical, but may vary depending on conditions beyond Christie's control such as maintenance of
the product in proper working conditions. Performance specications are based on information
available at the time of printing. Christie makes no warranty of any kind with regard to this material,
including, but not limited to, implied warranties of tness for a particular purpose. Christie will not
be liable for errors contained herein or for incidental or consequential damages in connection with
the performance or use of this material.
The product is designed and manufactured with high-quality materials and components that can
be recycled and reused. This symbol means that electrical and electronic equipment, at their
end-of-life, should be disposed of separately from regular waste. Please dispose of the product
appropriately and according to local regulations. In the European Union, there are separate
collection systems for used electrical and electronic products. Please help us to conserve the
environment we live in!
Canadian manufacturing facility is ISO 9001 and 14001 certied.
GENERAL WARRANTY STATEMENTS
For complete information about Christie’s limited warranty, please contact your Christie dealer. In
addition to the other limitations that may be specied in Christie’s limited warranty, the warranty
does not cover:
a. Damage occurring during shipment, in either direction.
b. Projector lamps (See Christie’s separate lamp program policy).
c. Damage caused by use of a projector lamp beyond the recommended lamp life, or use of a lamp
supplied by a supplier other than Christie.
d. Problems caused by combination of the product with non-Christie equipment, such as distribution
systems, cameras, video tape recorders, etc., or use of the product with any non-Christie interface
device.
e. Damage caused by misuse, improper power source, accident, re, ood, lightening, earthquake or
other natural disaster.
f. Damage caused by improper installation/alignment, or by product modication, if by other than a
Christie authorized repair service provider.
g. For LCD projectors, the warranty period specied applies only where the LCD projector is in “normal
use.” “Normal use” means the LCD projector is not used more than 8 hours a day, 5 days a week.
For any LCD projector where “normal use” is exceeded, warranty coverage under this warranty
terminates after 6000 hours of operation.
h. Failure due to normal wear and tear.
PREVENTATIVE MAINTENANCE
Preventative maintenance is an important part of the continued and proper operation of your
product. Please see the Maintenance section for specic maintenance items as they relate to your
product. Failure to perform maintenance as required, and in accordance with the maintenance
schedule specied by Christie, will void the warranty.

G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Table of Contents
i
1. SAFETY
2. INTRODUCTION
2.1 Projector Components..................................................................................................2-1
2.2 Built-in Keypad .............................................................................................................2-4
2.3 Input/Output (I/O) Panel ...............................................................................................2-5
2.4 Remote Control ............................................................................................................2-6
2.5 LED Status Indicators...................................................................................................2-8
3. INSTALLATION
3.1 Connect to Computer ...................................................................................................3-1
3.2 Connect to Video Equipment........................................................................................3-2
3.3 Turn the Projector On...................................................................................................3-3
3.4 Turn the Projector Off...................................................................................................3-3
3.5 Adjust the Projector Position ........................................................................................3-4
3.6 Calculate Lens Offset ...................................................................................................3-5
3.7 Removing and Installing the Lens ................................................................................3-11
3.8 Cable Cover Installation ...............................................................................................3-12
4. OPERATION
4.1 Size and Position Menu................................................................................................4-2
4.2 Image Settings Menu....................................................................................................4-7
4.3 Conguration Menu ......................................................................................................4-10
4.4 Lamp Menu...................................................................................................................4-15
4.5 Status Menu .................................................................................................................4-16
4.6 Input Switching & PIP Menu.........................................................................................4-19
4.7 Language Menu............................................................................................................4-21
4.8 Test Pattern Menu ........................................................................................................4-21
4.9 Web User Interface.......................................................................................................4-22
4.9.1 Logging On..........................................................................................................4-22
4.9.2 Main Tabbed Page – General .............................................................................4-22
4.9.3 Main Tabbed Page – Status................................................................................4-23
4.9.4 Main Tabbed Page – Lens ..................................................................................4-24
4.9.5 Network ...............................................................................................................4-24
4.9.6 Tools....................................................................................................................4-27
4.9.8 About Page..........................................................................................................4-28
4.10 Christie Presenter.........................................................................................................4-29
4.10.1 Connect to the Projector....................................................................................4-29
4.10.2 Install Christie Presenter software.....................................................................4-30
4.10.3 Use Christie Presenter ......................................................................................4-31
4.11 Card Reader Operation................................................................................................4-37
4.12 Install the Lamp............................................................................................................4-41
5. TROUBLESHOOTING
6. SPECIFICATIONS
6.1 Inputs............................................................................................................................6-1
6.2 PIP/PBP Compatibility..................................................................................................6-6
6.3 Key Features ................................................................................................................6-7
6.4 List of Components.......................................................................................................6-8
6.5 Optional Accessories....................................................................................................6-8
6.6 REGULATORY.............................................................................................................6-9

G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Table of Contents
ii
6.7 Federal Communications Commission (FCC) Warning................................................6-10
6.8 OSD Tree .....................................................................................................................6-11
6.9 Preset Mode tables.......................................................................................................6-19

G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Section 1: Safety
1-1
1. SAFETY
Read through this document in its entirety and understand all warnings and
precautions before attempting to operate the projector.
yDo not look into the projector lens when the lamp is on. The bright light
may result in permanent eye damage.
yTo reduce the risk of re or electric shock, do not expose this projector to
rain or moisture.
yDo not open or disassemble the projector as this may cause electric shock.
yWhen replacing the lamp, allow the projector to cool, and follow all
replacement instructions.
yWhen you turn the projector off, wait 180 seconds for the projector to cool
down before you disconnect the projector from power.
yCooling the lamp during the ignition phase may lead to ignition failures.
After a successful lamp ignition, keep the lamp burning for at least 5
minutes to maintain lamp life.
yWhen the lamp is approaching the end of its life, the message “Lamp is
approaching the end of its useful life in full power operation” appears on
the screen. Change the lamp when the warning message appears.
yAll installation and maintenance procedures must be performed by a
Christie accredited service technician.
yKeep all combustible material away from the concentrated light beam of
the projector.
yPosition all cables where they cannot contact hot surfaces or be pulled or
tripped over.
WARNING

G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Section 1: Safety
1-2
yAlways power down the projector and disconnect all power sources before
servicing or cleaning.
yUse a soft cloth moistened with a mild detergent to clean the display
housing.
yDisconnect the power plug from the AC outlet if the product is not being
used for an extended period of time.
yOperate the projector under the following conditions:
-Operating temperature range: 5°C to 35°C
-Storage temperature range: -10°C to 60°C
-Humidity range: 5% to 80 % RH (Max.), non condensing
-Operating altitude: 10,000 ft. maximum
yUse only the AC power cord supplied. Do not attempt operation if the AC
supply and cord are not within the specied voltage and power range for
your region.
yRemove the lens plug from the lens opening in the projector before
installing the lens. Retain the lens plug to protect the optical components
from dust and debris during transport.
yDo not block the ventilation slots and openings on the projector.
yDo not use abrasive cleaners, waxes or solvents to clean the projector.
yDo not allow anything to rest on the power cord.

G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Section 2: Introduction
2-1
2. INTRODUCTION
The product specied in this document is a high brightness, high-resolution
video/graphics 1-chip mercury lamp based projector. The projector is available
in WXGA, HD and WUXGA resolutions. The projector utilizes Digital Light
Processing (DLP®) technology from Texas Instruments. It is primarily designed
for xed installation markets.
2.1 Projector Components
Front View
2
1
4
Ind. Part Name Description
1 Front IR Sensor Receives signals from the IR remote. Keep the signal path to the sensor unobstructed for uninterrupted
communication with the projector.
2 Projection Lens Allows automated lens control and adjustment: vertical
and horizontal offsets, zoom and focus.
3 Lens Ring Protects the lens motors and mechanism. Remove in
order to insert or remove the lens.
4 Adjustable Feet Raise or lower the feet to level the projector.
3

G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Section 2: Introduction
2-2
Rear View 1
5
2
3
6
4
Ind. Part Name Description
1 Rear IR Sensor Receives signals from the IR remote. Keep the signal path unobstructed for uninterrupted communication
with the projector.
2Input/Output (I/O)
Panel Connects the projector to external devices.
3Cooling Air Vents
(Exhaust) Keep these vents unobstructed to prevent the projector from overheating.
4 AC Input Connect to the supplied power adapter.
5 Power Button Switch the power button to turn on the power source.
6 Kensington Lock Use to secure the projector to countertops, tables, etc.

G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Section 2: Introduction
2-3
Right View
LAMP
Left View
1
2
3
4
Ind. Part Name Description
1 Lamp Door Use the lamp door to access the lamp module.
2 LED Status Indicators Displays the status of the projector. They are (from left
to right): LAMP, STATUS, and PIC MUTE.
3 Built-in Keypad Controls the projector.
4Cooling Air Vents
(Intake) Keep these vents unobstructed to prevent the projector from overheating.

G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Section 2: Introduction
2-4
2.2 Built-in Keypad
7
8
9
10
2
4
5
611
1
3
Ind. Key Name Description
1 Power Turn the projector on or off
2 Menu Display menus
3 Enter Conrm a selection
4 Auto Automatically optimize image
5 Lens Adjust the lens vertical or horizontal offset setting
6 Focus Adjust focus
7 Exit Return to previous level or exit menus if at top level
8Arrow Keys
yAdjust a setting UP or DOWN
yNavigate within a menu
9 Input Select an input for the main or PIP/PBP image
10 Picture Mute Display or blank the video image.
11 Zoom Adjust zoom

G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Section 2: Introduction
2-5
2.3 Input/Output (I/O) Panel
Ind. Connector Name Ind. Connector Name
1 Remote IN 8Mini USB
2 Remote OUT 9 USB Type A
3 Component IN 10 DisplayPort
4 CVBS 11 HDMI
5 S-Video 12 VGA-IN
6 RS232 13 VGA OUT
7 Ethernet 14 DVI
1 2 3 4 5
78910 11 12 13 14
6

G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Section 2: Introduction
2-6
2.4 Remote Control
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29

G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Section 2: Introduction
2-7
Ind. Key Name Description
1 Picture Mute Display or blank the video image.
2 Power on Turn projector ON.
3 Gamma Adjust mid-range levels.
4 Bright Adjust amount of light in the image.
5 PIP/PBP Turn PIP/PBP ON/OFF.
6 Size Adjust the PIP/PBP size
7 Number Keys Enter a number, such as a channel, value, etc.
8Help Display context-sensitive help.
9 Menu Display menus.
10 Arrow Keys
yAdjust a setting UP or DOWN.
yNavigate within a menu.
11 Test Display a test pattern.
12 Auto Automatically optimize image.
13 OSD Use to hide or show menus.
14 Keystone H Adjust the horizontal keystone.
15 Keystone V Adjust the vertical keystone.
16 Standby Turn projector OFF.
17 Contrast Adjust difference between dark and light.
18 Hot-key Select your preset keys quickly.
19 Swap Swap the main and PIP/PBP images.
20 Layout Adjust the PIP/PBP layout.
21 Focus Adjust focus to improve image clarity as desired.
22 Zoom Adjust zoom to achieve a desired image size.
23 Proj Key Change the remote ID. Press Proj Key then a number between 1 and 9 to assign an ID. Press PROJ then
number 0 to return to the universal remote ID.
24 Exit Return to previous level or exit menus if at top level.
25 Enter
ySelect a highlighted menu item.
yChange or accept a value.
26 Input Select an input for the main or PIP/PBP image.
27 Info Display source image information.
28 Lens H Horizontal Lens Shift - Adjust the position of the image
horizontally.
29 Lens V Vertical Lens Shift - Adjust the position of the image
vertically.

G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Section 2: Introduction
2-8
2.5 LED Status Indicators
The LED status indicators are located on the right side of the projector. Each
LED is dened below.
yLAMP LED
LED Status Projector State
Red (short blink)
Failed to strike lamp after 5 attempts (strike attempts will
stop).
Lamp has unexpectedly shut down (system goes into cool
down state).
Yellow (no blink) Lamp time has expired and lamp should be replaced. (projector also begins to display the replace lamp OSD
message at startup).
Green (no blink) Lamp is ON and operating correctly
Green (short blink) Projector lamp is switching on
Off Lamp is off
ySTATUS LED
LED Status Projector State
Off Projector is in OFF state (without AC plug in)
Off, but keypad LED
is on Projector is in standby mode (AC plug in)
Green (no blink) Projector is powered up and operating normally
Flashing Yellow Projector is in cool down mode or startup mode
Flashing Green/
Yellow Projector is in ash update state
Red (short blink) Fan failure
Red (no blink) Over-temperature
Green (blink very
quickly) Projector communications (Read/Write EEPROM)

G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Section 2: Introduction
2-9
yPICTURE MUTE LED
LED Status Projector State
Green Picture mute is off – image is displayed
Yellow Picture mute is on – image is black

G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Section 3: Installation
3-1
3. INSTALLATION
3.1 Connect to Computer
NOTE:
The diagram shows the cables/connectors that may be used to connect to various devices.
Due to the difference in applications for each country, the accessories required in some regions may be different from those
shown.
This diagram is for illustrative purposes only, and does NOT indicate that these accessories are supplied with the projector.
Ind. Connector Name Ind. Connector Name Ind. Connector Name
1USB Type B Mini
Cable 4 HDMI Cable 7 RS232 Cable
2 USB Type A Cable 5 VGA in Cable 8DVI Cable
3 DisplayPort Cable 6 VGA out Cable 9 Power Cord
Desktop Laptop
51 62 3 4 78
9

G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Section 3: Installation
3-2
3.2 Connect to Video Equipment
NOTE:
The diagram shows the cables/connectors that may be used to connect to various devices.
Due to the difference in applications for each country, the accessories required in some regions may be different from those
shown.
This diagram is for illustrative purposes only, and does NOT indicate that these accessories are supplied with the projector.
Component video output equipment DVD player Video cassette recorder
41
5
7
8
2 3
6
Ind. Connector Name Ind. Connector Name Ind. Connector Name
1 HDMI Cable 4 S-Video Cable 7 3 RCA Component
Cable
2Component (YPbPr)
Cable 5 VGA to RBG SCART 8
15-pin to 3 RCA
Component/HDTV
Adapter
3 CVBS Cable 6 VGA in Cable

G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Section 3: Installation
3-3
3.3 Turn the Projector On
1. Ensure that the power cord and signal cable are securely connected. The
Power button on the built in keypad is illuminated.
1
2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
2. Turn on the lamp by pressing “”on the remote control or press “” on
the built-in keypad. The Status LED is yellow with a long blink.
1
2
3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
The startup screen displays in approximately 10 seconds.
3. Turn on the source. Select Input Key on the remote control to select an
input source (VGA, BNC, HDMI, Component, S-Video or Composite
Video).
1 2
3
4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
4. The projector detects the source you selected and displays the image.
NOTE:
The rst time the projector is used, the preferred language may be selected from the main menu after the startup screen is
displayed.
3.4 Turn the Projector Off
1. Press “”on the built-in keypad or on the remote control to turn off the
projector. A warning message will appear on the displayed image.
2. Press “” again to conrm your selection. If you do not press “”again,
the warning message will disappear after 10 seconds.
Input Key
1 2
3
4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
Power on
1
2
3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
Status LED
1
2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
Power on
1
2
3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20