Christie LX400 User manual

LX400
USER MANUAL - NETWORK GUIDE
020-000170-02

NOTICE for European Union members 《 ENGLISH
》
This is a Class A product in European Union.
WARNING :
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
AVIS pour les membres du Union Européenne 《 FRANÇAIS
》
Le présent appareil est un produit de classe A, dans Union Européenne.
AVERTISSEMENT :
Le présent appareil est un produit de classe A. En environnement domestique, ce produit
est susceptible de provoquer des interférences radio-électriques, auquel cas l’utilisateur
devra prendre les mesures adéquates.
BEACHTUNG für Europäischen Union-Mitglieder 《 DEUTSCH
》
Dies ist ein Produkt der Klasse A, in Europäischen Union.
WARNUNG :
Dies ist ein Produkt der Klasse A. Bei der Verwendung im häuslichen Bereich können
Störungen des Radio- oder Fernsehempfangs auftreten. Beim Auftreten derartiger
Störungen hat der Benutzer gegebenenfalls Abhilfemaßnahmen zu treffen.
AVISO para los miembros de Unión Europea 《 ESPAÑOL
》
Este es un producto de Clase A, en Unión Europea
ADVERTENCIA :
Este es un producto de Clase A. En un entorno doméstico este producto puede causar
radio interferencias, en cuyo caso el usuario deberá tomar las medidas pertinentes.
DICHIARAZIONE per membri di Unione europea 《 ITALIANO
》
Questo è un prodotto di Classe A, negli Unione europea.
AVVERTENZA :
Questo è un prodotto di Classe A. In un ambiente domestico, questo prodotto potrebbe
causare interferenze radio, nel cui caso l’utente è obbligato a prendere gli adeguati
provvedimenti.
BEMERK for EU-medlemmer 《 NORSK
》
Dette er et klasse A produkt, i EU.
ADVARSEL :
Dette er et klasse A produkt. I et hjemmemiljø kan dette produktet forårsake
radiointerferens, og i dette tilfellet anbefales det at brukeren tar tilstrekkelige
forholdsregler.
OPMERKING voor de Europese Unie leden 《 NERDERLANDS
》
Dit is een klasse A product, in Europese Unie.
WAARSCHUWING :
Dit is een klasse A product. In een huiselijke omgeving kan dit product radio-
interferentie veroorzaken. De gebruiker is dan verplicht om maatregelen te nemen om de
interferentie te ongedaan te maken.

NOTIFICAÇÃO para sócios de União europeus 《 PORTUGUÊS
》
Trata-se de um produto Classe A, em União européia.
AVISO :
Trata-se de um produto Classe A. Num ambiente doméstico, este produto pode provocar
interferências rádio, podendo ser necessário tomar medidas adequadas.
䗮ⶹ󱂜⌆㘨ⲳ៤ 《Ё᭛》 
ᴀѻકᰃ $ 㑻ѻક೼󱂜⌆㘨ⲳ (8
䄺
ᴀѻકᰃ $ 㑻ѻકDŽ೼ᆊᒁ⦃๗Ёˈᴀѻકৃ㛑Ӯᇐ㟈᮴㒓⬉ᑆᡄˈ䖭⾡ᚙމϟˈ
⫼᠋䳔䞛প䗖ᔧⱘ᥾ᮑDŽ
氦崃櫶穯ͶΆ儆沋箒毖櫖堆穢皻滆 《穢剳檺》
決冉汆氦崃櫶穯ͶΆ櫖昢畺岞枪Ͳ洢禎沋城埪 .
凃処 :
懾洢禎汆畺岞枪Ͳ洢禎沋城埪 懾洢禎汆其渂筞凃喺櫖昢斲殯沖汞
洇洎穢浶獞庂穊殚嵢穞垚怺昦儊昳汊氦愢穦朞沎枻城埪 
ANMÄRKNING för EU-medlemmar 《 SVENSKA
》
Detta är en klass A-produkter, i EU.
VARNING :
Detta är en klass A-produkt. I hemmiljö kan denna produkt orsaka radiostörningar mot
vilka användaren måste vidta åtgärder.
ПРЕДОСТЕРЕЖЕНИЕ для членов Европейском Союзе (EC)
《РУССКИЙ》
Это изделие Класса А, в Европейском Союзе (EC).
ПРЕДУПРЕЖДЕНИЕ :
Это изделие Класса А. В бытовых условиях это изделие может стать причиной
возникновения радиопомех, в случае чего пользователь должен предпринять
соответствующие меры.
HUOMAA ajaksi Euroopan Unionin jäseniä 《 SUOMI
》
Tämä on luokan A tuote on Euroopan unionin.
VAROITUS :
Tämä laite on luokan A tuote. Kotikäytössä tämä tuote saattaa aiheuttaa radiohäiriötä.
Käyttäjän on tällöin ehkä ryhdyttävä korjaaviin toimenpiteisiin.
UWAGA dla członków Unii Europejskie 《 POLSKI
》
Jest to produkt klasy A, w Unii Europejskiej.
ZAGROŻENIE :
Jest to produkt klasy A. W środowisku domowym może on wywoływać zakłócenia
radiowe, co oznacza, że użytkownik będzie musiał podjąć odpowiednie środki zaradcze.

1
Projector
LX400
User's Manual (detailed)
Network Guide
Thank you for purchasing this projector.
This projector has the network function that brings you the following main features.
►Before using this product, be sure to read all manuals for this
product.
After reading them, store them in a safe place for future reference.
WARNING
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
NOTE
Trademark acknowledgment
• Microsoft®and Internet Explorer®, Windows®, Windows Vista®are registered
trademark of Microsoft Corporation in the U.S. and/or other countries.
• JavaScript®is a registered trademark of Sun microsystems, Inc.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks
or registered trademarks of HDMI Licensing LLC.
All other trademarks are the properties of their respective owners.
Web control
The projector can be controlled and monitored by a web browser software on
your PC, which can help you to setup and maintain the projector.
e-SHOT (Still Image Transfer) Display
The projector can display still images that are transferred via the network.
This manual is only intended to explain Network function only.
For safety, operations or any other issues, refer to the Safety Guide and User’s
Manual (concise and detailed).
LX400 User Manual - Network Guide 020-000170-02 Rev. 1 (08-2009)

2
Content
Content

About this manual.......................................................................... 1
Content ..........................................................................................2
1. Main functions ........................................................................... 3
1.1 Configuring and controlling via a web browser ...........................................3
1.2 e-SHOT (Still image Transfer) Display........................................................ 3
2. Equipment connection and network setting.............................4
2.1 Required equipment preparation ................................................................ 4
2.2 Manual network connection setting............................................................. 5
2.2.1 Equipments connection.........................................................................5
2.2.2 Network settings....................................................................................5
2.2.3 “Internet Option” setting.........................................................................8
2.2.4 Check connection..................................................................................9
3. Network functions ................................................................... 10
3.1 Configuring and controlling the projector via a web browser .................... 11
3.1.1 Logon .................................................................................................. 13
3.1.2 Network Information ............................................................................ 14
3.1.3 Network Settings ................................................................................. 15
3.1.4 Port Settings........................................................................................17
3.1.5 Mail Settings........................................................................................18
3.1.6 Alert Settings .......................................................................................19
3.1.7 Schedule Settings ...............................................................................21
3.1.8 Date/Time Settings..............................................................................23
3.1.9 Security Settings ................................................................................. 25
3.1.10 Projector Control ............................................................................... 27
3.1.11 Projector Status .................................................................................30
3.1.12 Network Restart.................................................................................31
3.1.13 Logoff ................................................................................................ 31
3.2 E-mail Alerts.............................................................................................. 32
3.3 Projector Management using SNMP......................................................... 34
3.4 Event Scheduling......................................................................................35
3.5 e-SHOT (Still Image Transfer) Display......................................................38
3.6 Command Control via the Network...........................................................40
020-000170-02 Rev. 1 (08-2009) LX400 User Manual - Network Guide

3
1. Main functions
1. Main functions
1.1 Configuring and controlling via a web browser
You can adjust or control the projector via a network from a web browser on a PC
that is connected to the same network.
Logon the network from the web browser and it offers the menus to configure the
network settings, monitor the projector and so on.
1.2 e-SHOT (Still image Transfer) Display
Image files can be sent via the network, and up to 4 image data can be stored in
the projector and displayed on screen one by one. (38)
Transfer image data
Display image data ( 1- 4)
LX400 User Manual - Network Guide 020-000170-02 Rev. 1 (08-2009)

4
2. Equipment connection and network setting
2.1 Required equipment preparation
2. Equipment connection and network setting
The following equipments are required to connect the projector to your PC through
the network.
PC : 1) equipped with the network feature
2) installed a web browser software (11)
LAN cable : CAT-5 or greater
• The system for using the network function of the projector requires
communication environment conforming 100Base-TX or 10Base-T.
NOTE
020-000170-02 Rev. 1 (08-2009) LX400 User Manual - Network Guide

5
2. Equipment connection and network setting
2.2 Manual network connection setting
2.2.1 Equipments connection
Connect the projector and PC with a LAN cable.
* Before connecting with an existing network, contact the network administrator.
Next, please check the PC setting as explained below.
2.2.2 Network settings
This is the explanation of network connection settings for Windows®XP and
Internet Explorer®.
1) Log on to Windows®XP as administrator authority. (*)
2) Open “Control Panel” from “Start” menu.
3) Open “Network and Internet Connections” in “Control Panel”. (Fig. 2.2.2.a)
* Administrator authority is the account, which can access to all functions.
4) Open “Network Connections”. (Fig.2.2.2.b)
Fig. 2.2.2.a “Network and Internet Connections” window
Fig. 2.2.2.b “Network Connections” window
LX400 User Manual - Network Guide 020-000170-02 Rev. 1 (08-2009)

6
2. Equipment connection and network setting
2.2 Manual network connection setting (continued)
7) Set IP address, subnet mask and default gateway for PC.
Fig. 2.2.2.d “Internet Protocol (TCP/IP) Properties” window
5) Open “Local Area Connection Properties” window you use for network device.
(Fig. 2.2.2.c)
6) Set used protocol as “TCP/IP” and open “Internet Protocol (TCP/IP) Properties”
window.
Fig. 2.2.2.c “Local Area Connection Properties” window
020-000170-02 Rev. 1 (08-2009) LX400 User Manual - Network Guide

7
2. Equipment connection and network setting
2.2 Manual network connection setting (continued)
[About IP address]
■ Setting manually
The Network address portion included in the IP address set into your PC should
be common with projector’s one. And the entire IP address in the PC should not
be overlapped with other equipments in the same network, including the projector.
The projector’s initial settings are as follows.
IP address: 192.168.1.10
Subnet mask: 255.255.255.0
(Network address: 192.168.1 in this case)
Therefore, specify PC’s IP address as follows.
IP address: 192.168.1.xxx (xxx shows decimal number.)
Subnet mask: 255.255.255.0
(Network address: 192.168.1 in this case)
For example
Select from 1 to 254 for “xxx” not duplicating with any other equipments.
In this case, projector has “192.168.1.10” IP address, specify from 1 to 254
except 10 for PC.
• “0.0.0.0” cannot be set to the IP address.
• The projector’s IP address can be changed by using the configuration utility
via a web browser. (11)
• If the projector and PC exist in the same network (i.e. network address is
common), default gateway can be blank.
• When the projector and PC exist in different networks, default gateway setting
is necessary. Contact the network administrator in detail.
NOTE
■ Setting automatically
When DHCP server exists in network, it is possible to assign IP address to the
projector and PC automatically.
* DHCP is abbreviation for “Dynamic Host Configuration Protocol” and has the
function to provide necessary setting for network like IP address from server to
client. A server that has DHCP function is called DHCP server.
LX400 User Manual - Network Guide 020-000170-02 Rev. 1 (08-2009)

8
2. Equipment connection and network setting
2.2 Manual network connection setting (continued)
2) Click “Connections” tab and then click [LAN Settings] button to open “Local
Area Network (LAN) settings”. (Fig. 2.2.3.c)
Fig. 2.2.3.b “Internet Properties” window
2.2.3 “Internet Option” setting
1) Click “Internet Options” in “Network and Internet Connections” window
(Fig. 2.2.3.a) to open “Internet Properties” window. (Fig.2.2.3.b)
Fig. 2.2.3.a “Network and Internet Connections” window
Click
Click
020-000170-02 Rev. 1 (08-2009) LX400 User Manual - Network Guide

9
2. Equipment connection and network setting
2.2 Manual network connection setting (continued)
Fig. 2.2.4 “Logon Menu”
2.2.4 Check connection
Check PC and projector are connected properly here. If it is not connected, check
cable connections and settings are properly or not.
1) Start browser in PC and specify following URL, then click “Go” button.
Fig. 2.2.3.c “Local Area Network (LAN) Settings” window
3) Uncheck all boxes in “Local Area Network (LAN) Settings” window. (Fig. 2.2.3.c)
URL: http://(Projector IP address)/
For example, if projector IP address is 192.168.1.10, specify
2) If Fig. 2.2.4 appears, it succeeds.
URL: http://192.168.1.10/
LX400 User Manual - Network Guide 020-000170-02 Rev. 1 (08-2009)

10
3. Network functions
Configuring and Controlling the Projector via a Web Browser
You can change the settings of or control the projector via a network by using a
web browser from a PC that is connected to the same network.
(11)
E-mail Alerts
The projector can automatically send an alert to specified e-mail addresses when
the projector requires maintenance or has encountered an error.
(32)
Projector Management using SNMP
This projector is SNMP (Simple Network Management Protocol) compliant,
allowing you to monitor it from a remote location using SNMP software. In
addition, the projector is able to send failure & warning alerts to a specified PC.
(34)
Event Scheduling
You can schedule the projector to perform various functions according to the date
and time.
(35)
e-SHOT (Still Image Transfer) Display
The projector can display still images that are transferred via the network.
(38)
Command Control via the Network
The projector can be controlled using RS-232C commands over a network.
(40)
3. Network functions
This projector is equipped with the following network functions by using a web
browser software.
020-000170-02 Rev. 1 (08-2009) LX400 User Manual - Network Guide

11
3. Network functions
3.1 Configuring and controlling the projector via a web
browser
You can adjust or control the projector via a network from a web browser on a PC
that is connected to the same network.
• Internet Explorer®5.5 or later is required.
• If JavaScript®is disabled in your web browser configuration, you must enable
JavaScript®in order to use the projector web pages properly. See the Help files
for your web browser for details on how to enable JavaScript®.
• You can communicate using SSL (Secure Socket Layer) if you are using
Windows®XP Service Pack 2 or earlier versions of Microsoft®Windows®.
Please specify “https://” when you enter the IP address of the projector on the
web browser. You can't communicate the projector using SSL on Windows
Vista®.
• It is recommended that all web browser updates are installed. It is especially
recommended that all users running Internet Explorer®on a Microsoft®
Windows®version prior to Windows®XP Service Pack 2 install security update
Q832894 (MS04-004) or the web browser interface may not be displayed
correctly.
And when using an earlier version of Internet Explorer®, during operations the
browser will log out after 50 seconds.
NOTE
LX400 User Manual - Network Guide 020-000170-02 Rev. 1 (08-2009)

12
3. Network functions
When configuring or controlling the projector via a web browser, an ID and
password are required. There are two types of IDs, Administrator ID and User ID.
The following chart describes the differences between Administrator and User IDs.
3.1 Configuring and controlling the projector via a web browser (continued)
Item Description Administrator User
Network Information Displays the projector’s current
network configuration settings. √√
Network Settings Displays and configures network
settings. √ N/A
Port Settings Displays and configures
communication port settings. √ N/A
Mail Settings Displays and configures e-mail
addressing settings. √ N/A
Alert Settings Displays and configures failure &
warning alerts. √ N/A
Schedule Settings Displays and configures schedule
settings. √ N/A
Date/Time Settings Displays and configures the date and
time settings. √ N/A
Security Settings Displays and configures passwords
and other security settings. √ N/A
Projector Control Controls the projector. √ √
Projector Status Displays and configures the current
projector status. √√
Network Restart Restarts the projector’s network
connection. √ N/A
020-000170-02 Rev. 1 (08-2009) LX400 User Manual - Network Guide

13
3. Network functions
3.1 Configuring and controlling the projector via a web browser (continued)
3.1.1 Logon
Refer to the following for configuring or controlling the projector via a web browser.
1) Enter “http://192.168.1.10/” into the address
bar of the web browser and press “Enter”
key or click “Go” button. The screen in Fig.
3.1.1a will be displayed.
2) Enter your ID and password and click
[Logon].
Example: If the IP address of the projector is set to 192.168.1.10:
Fig. 3.1.1 a “Logon Menu”
Below are the factory default settings for administrator ID, user ID and passwords.
Item ID Password
Administrator Administrator <blank>
User User <blank>
If the logon is successful, either the Fig. 3.1.1 b or Fig. 3.1.1 c screen will be
displayed.
Fig. 3.1.1 b “Logon with Administrator ID”
Main menu
Fig. 3.1.1 c “Logon with User ID”
Main menu
3) Click the desired operation or configuration item on the main menu located on
the left-hand side of the screen.
LX400 User Manual - Network Guide 020-000170-02 Rev. 1 (08-2009)

14
3.1 Configuring and controlling the projector via a web browser (continued)
3.1.2 Network Information
All screen drawings in this manual are shown
when you logon with the Administrator ID.
Any functions that are available only for the
Administrator will not be shown when you logon
with the User ID. Refer to the table. (12,13)
3. Network functions
Displays the projector’s current network configuration settings.
Item Description
Projector Name Displays the projector name settings.
DHCP Displays the DHCP configuration settings.
IP Address Displays the current IP address.
Subnet Mask Displays the subnet mask.
Default Gateway Displays the default gateway.
MAC Address Displays the ethernet MAC address.
Firmware Date Displays the network firmware time stamp. This information
is only displayed when logged on using an Administrator ID.
Firmware Version
Displays the network firmware version number. This
information is only displayed when logged on using an
Administrator ID.
020-000170-02 Rev. 1 (08-2009) LX400 User Manual - Network Guide

15
3. Network functions
3.1 Configuring and controlling the projector via a web browser (continued)
3.1.3 Network Settings
Displays and configures network settings.
Item Description
IP Configuration Configures network settings.
DHCP ON Enables DHCP.
DHCP OFF Disables DHCP.
IP Address Configures the IP address when DHCP is disabled.
Subnet Mask Configures the subnet mask when DHCP is disabled.
Default Gateway Configures the default gateway when DHCP is disabled.
Projector Name
Configures the name of the projector.
The length of the Projector Name can be up to 64
alphanumeric characters. Only alphabets, numbers and
following symbols can be used. !"#$%&'()*+,-./:;<=>?@[\]^_`{
|}~ and space
sysLocation (SNMP)
Configures the location to be referred to when using SNMP.
The length of the sysLocation can be up to 255 alphanumeric
characters. Only numbers ‘0-9’ and alphabet ‘a-z’, ‘A-Z’ can
be used.
sysContact (SNMP)
Configures the contact information to be referred to when
using SNMP.
The length of the sysContact can be up to 255 alphanumeric
characters. Only numbers ‘0-9’ and alphabet ‘a-z’, ‘A-Z’ can
be used.
DNS Server Address Configures the DNS server address.
Click [Apply] button to save the settings.
LX400 User Manual - Network Guide 020-000170-02 Rev. 1 (08-2009)

16
3.1 Configuring and controlling the projector via a web browser (continued)
3. Network functions
• The new configuration settings are activated after restarting the
network connection. When the configuration settings are changed, you must
restart the network connection. You can restart the network connection by
clicking [Network Restart] on the main menu.
• If you connect the projector to an existing network, consult a network
administrator before setting server addresses.
NOTE
020-000170-02 Rev. 1 (08-2009) LX400 User Manual - Network Guide