Christie Solaria CP2210 Service manual

Replacing the ICP Battery Technical Bulletin 1
020-200313-01 Rev. 1 (02-2015)
Replacing the ICP Battery
This document provides instructions for replacing the Integrated Cinema Processor (ICP) battery. If
the ICP battery fails, projector time settings can become inaccurate and automated events might
not run as expected.
The ICP battery replacement takes approximately 30 minutes. Christie recommends replacing the
battery every five years.
Affected products
• Christie CP2210
• Christie CP2215
• Christie CP2220
• Christie CP2230
• Christie CP4220
• Christie CP4230
• Christie Solaria One
• Christie Solaria One+
Safety precautions
Prerequisites
• Replacement ICP battery (type BR2330)
• A USB flash drive with a minimum capacity of 8GB
• Texas Instruments ICP and Enigma Control Program
To request a copy of the software, contact Christie Technical Support.
Technical Bulletin
ELECTRICAL SHOCK HAZARD! Always turn off, disconnect, and disengage all power sources to the
projector before servicing. Failure to comply results in death or serious injury.
Only Christie accredited service technicians are permitted to open any enclosure on the projector and
only if the AC power has been fully disconnected. Failure to comply could result in minor or moderate
injury.
To prevent damage by static electricity, wear an anti-static wrist strap and follow anti-static protocols
when replacing the ICP battery.

Replacing the ICP Battery Technical Bulletin 2
020-200313-01 Rev. 1 (02-2015)
Replace the ICP battery
The ICP is installed in the card cage located on the operator (left) side of the projector facing the
lens. This procedure describes the replacement of an ICP battery in a Christie CP2215 projector. For
removal instructions that are specific to your projector model, see the projector Service Manual.
To prevent damage to the projector or personal injury, complete the procedures in the order they
are written.
Backup projector settings and information
This procedure is optional, but is recommended to make sure you can recover your data if an error
occurs.
1. Insert a USB flash drive into the USB port on the side of the projector touch panel controller
(TPC).
2. Log on to the projector with service permissions.
3. On the TPC, tap Menu > Service Setup > File Management.
4. Tap Backup.
5. When the backup is complete, remove the USB flash drive and store it in a secure location.
Prepare the projector for service
1. If the lamp is on, tap the lamp off ( ) icon on the projector TPC to turn it off.
2. Allow the lamp to cool for a minimum of 15 minutes.
3. Tap and hold the power off ( ) icon to turn the projector off.
4. Disconnect the projector from AC power.
Remove the ICP
1. Loosen the seven screws that secure the top lid to the projector.
2. Lift the lid up from the rear of the projector and set it aside.

Replacing the ICP Battery Technical Bulletin 3
020-200313-01 Rev. 1 (02-2015)
3. Unlock the high security lid with the high security key.
4. Lift the lid up and out and set it aside.
5. Reach into the projector and pull the lever to release the security ring.
6. Lower the security ring so it is out of the way.
7. Pull the ejectors on the ICP outward.
8. Pull the ICP outward out of the card cage and set it on a flat, stable surface.

Replacing the ICP Battery Technical Bulletin 4
020-200313-01 Rev. 1 (02-2015)
Remove and replace the ICP battery
1. Insert a flat screwdriver under the battery (A) and carefully lift it upward until it separates from
the retaining clip.
2. Remove the battery and set it aside.
Follow your local regulations for battery disposal.
3. Insert the new battery beneath the retaining clip.
Reinstall the ICP and reassemble the projector
1. Insert the ICP with even pressure into the card cage until it is firmly seated on the backplane.
2. Push the ejectors on the ICP faceplate inward to lock the ICP in position.
3. Replace the high security ring.
4. Replace the high security lid and lock it with the high security key.
5. Place the top lid on the projector and tighten the seven screws to secure it in position.
6. Reconnect the projector to AC power.
7. On the projector TPC, tap and hold the green power ( ) icon.
Activate marriage
You must complete marriage to display encrypted content and to comply with the Digital Cinema
Initiatives (DCI) specification.
1. Log on to the projector with marriage permissions.
2. Tap Menu > Service Setup > LD Marriage.
3. Complete the Marriage wizard.
4. Click Finish.

Replacing the ICP Battery Technical Bulletin 5
020-200313-01 Rev. 1 (02-2015)
Reset the ICP real-time clock
1. Download and install the ICP and Enigma Control Program on a computer that you can connect
to the projector.
2. Connect one end of an Ethernet cable to the Ethernet port on the computer with the ICP and
Enigma Control Program.
3. Connect the other end of the Ethernet cable to the Ethernet port on the projector.
4. Click Start > All Programs > ICP and Enigma Control Program.
5. On the Connection tab, select External Ethernet Port.
6. In the Ethernet Configuration area, enter the projector IP address in the IP Addr field and
press Select.
7. In the Login area, click Login.
8. Complete the User ID and Password fields and click OK.
9. Click OK.
10. Click the Sys-Config tab.
11. Click RTC Time.
12. In the Set Time area, select PC Time (UTC) and click Set RTC Time.
13. Close the ICP and Enigma Control Program.
Restore projector settings and information
This procedure is optional. Complete this procedure if an error has occurred and you need to
recover projector settings and other data.
1. Log on to the projector with service permissions.
2. Insert the USB flash drive with the backup into the USB port on the side of the projector.
3. Tap Menu > Service Setup > File Management.
4. Tap Browse to the right of the File to restore field.
5. Select the location of the upgrade file in the Drive Letter list.
6. Browse to the location of the upgrade file in the Folder list.
7. Tap the upgrade file and then tap Open.
8. Select the type of file to restore in the Select type list.
9. Tap Restore.
10. Tap Yes.

Replacing the ICP Battery Technical Bulletin 6
020-200313-01 Rev. 1 (02-2015)
Technical support
North and South America: [phone] or [email protected]
Europe, Middle East, and Africa: [phone] or [email protected]
Asia Pacific: [email protected]
Christie Managed Services: [phone] or [email protected]