Chroma Inspire User manual

Inspire Terminal Strip Quick Start Guide V1.01 Inspire Terminal Strip Quick Start Guide V1.01 PN: 632-0 0
Approvals & Disclaimer
The information contained herein is offered in good faith and is believed to be accurate. However,
because conditions and methods of use of our products are beyond our control, this information should
not be used in substitution for customer's tests to ensure that Chroma-Q products are safe, effective,
and fully satisfactory for the intended end use. Suggestions of use shall not be ta en as inducements to
infringe any patent. Chroma-Q sole warranty is that the product will meet the Chroma-Q sales
specifications in effect at the time of shipment. Your exclusive remedy for breach of such warranty is
limited to refund of purchase price or replacement of any product shown to be other than as warranted.
Chroma-Q reserves the right to change or ma e alteration to devices and their functionality without notice
due to on-going research and development.
The Chroma-Q Inspire range has been designed specifically for the lighting industry. Regular
maintenance should be performed to ensure that the products perform well in the entertainment
environment.
If you experience any difficulties with any Chroma-Q products please contact your selling dealer. If your
selling dealer is unable to help please contact [email protected]. If the selling dealer is unable to
satisfy your servicing needs, please contact the following for full factory service:
Outside North America: North America:
Tel: [phone] Tel: [phone]
Fax: [phone] Fax: [phone]
[email protected] [email protected]
For further information please visit the Chroma-Q website at www.chroma-q.com.
Chroma-Q and Inspire Terminal Strip are trademar s, for more information on this visit www.chroma-
q.com/trademar s.
The rights and ownership of all trademar s are recognised.
Quick Start Guide
Chroma-Q
®
Inspire™ Terminal Strip
For a full product manual please visit www.chroma-q.com
Software Version 1.01

Inspire Terminal Strip Quick Start Guide V1.01 Inspire Terminal Strip Quick Start Guide V1.01
1. Overview
The new Chroma-Q
®
Inspire™ Terminal Strip LED house light features a single light engine with 36 high powered LEDs
(RGBW), a fully homogenized optic and controlled via the Inspire™ External Control Box. Through the Inspire External
Control Box, the fixture can be controlled remotely through the ANSI E1.11 USITT DMX 512-A protocol.
2. Safety
Caution
CautionCaution
Caution
1. This product is for professional use only. It is NOT intended for domestic or outdoor use.
2. The bright flash of light during power-up & continuous strobe may cause epileptic seizure.
3. This product must be used with a safety cable.
3. Cabling
System Diagram: (Figure 1)
Power & Data Connections: (Figure 2)
Power Input: (Figure
3
)
Control Data: (Figure
4
)
To connect the wiring for power and control data:
•Remove the cover plate for power input.
•Insert the AC power cable with strain relief through the cover plate and connect to the Terminal Block Plug and
into the Terminal Block header in the fixture. (Figure 2 & 3)
•Put back and fasten the cover plate
•Connect the DMX control data cables from the Inspire External Control Box to the Terminal Block Plug and plug
into the Terminal Block headers at the rear of the fixture (Figure 2 & 4)
4. Mounting
A mounting bracket is built into the enclosure for overhead applications. Secure the fixture with a safety bond. A fixing
hold is built into the enclosure.
5. Optics
The Inspire can be built with either Narrow, Medium or Wide lens. The beam angles are:
Narrow: ~32°; Medium: ~42°; Wide: ~65°
6. Control
The control functions are accessed through the Touch Screen display at the front panel of the Inspire External Control
Box. The features of the Touch Screen Display are:
Control Menu
Main Menu
Displays the model name, DMX information, AC and Emergency
power input and Command buttons
Address Sets the DMX start address for each output: Output 1, Output 2, Output 3
Maximum DMX cable
length from Data Out
1/2/3 to the 1st fixture
must not exceed
500’/152m.
Note: The DMX cable
connected to the first Terminal
Strip fixture from each Data
Output of the External Control
Box must be terminated with a
120 ohm resistor. See Inspire
Terminal Strip User Manual
for details.

Inspire Terminal Strip Quick Start Guide V1.01 Inspire Terminal Strip Quick Start Guide V1.01
Mode
Select from the control mode options:
RGBW single 4 channels x RGBW for each fixture in each output
(up to 512 channels per output)
RGBW output
4 channels x RGBW for all fixtures in each
output
Tungsten
1 channel
x
W
for all fixtures in each
output
Loo Store Save and Load a Loo
Setup Menu Set the internal settings of the Inspire External Control:
DMX Data Displays DMX values
RotateDisp
Change the
display orientation
Frequency
To change the LED scan rate frequency, s
elect from:
1200Hz 2400Hz 4800Hz 9600Hz
DMX Lost
When DMX is not detected, s
elect from
the output options
:
Last Data
No Output
Loo
Reset Reset to user saved or default settings. (see User Manual)
. Further Information
Please refer to the Chroma-Q Inspire Terminal Strip manual for more detailed information. A copy of the manual can be found
at the Chroma-Q website – www.chroma-q.com – under Support.