Cineroid FL1600k User manual

FL1600k / FL1600vk
Important Safety Instructions
User's Manual

The Cineroid LED employs a very high color rendering index (CRI).
It displays a very stable color temperature and brightness so that both motion
pictures and still images can be taken in their most natural color tones.
Please read this user manual thoroughly before using the Cineroid LED.
Important Safety Instructions
Thank you for purchasing CINEROID FL1600.
Do not use batteries, power cord, or accessories that are not specied in this document.
When using a power cord, be sure to plug it in completely.
Do not handle power plugs when your hands are wet.
When unplugging the power cord, grasp the plug body or adapter instead of the cord.
Power cords that are scratched, heavily bent or twisted can potentially be hazardous and a
source of electric shock and/or re.
Do not insert foreign objects into the product's electric or cable components.
Do not place the power cord near sources of heat as this may melt or cause damage to the cord
potentially causing re or electric shock.
Do not disassemble or modify the product.
This may damage the product and cause danger due to a malfunction.
Please keep the product out of reach of young children. Injuries may occur due to damage to the
product.
When using the product in an airplane or hospital setting, it is recommended to acquire
authorization rst as signals or electro-magnetic waves from the product may cause other
equipment to malfunction.
Do not store the product in a dusty or humid environment as damage may occur.
When the product is mounted on a camera, do not lift or move the camera by grabbing the
product.This may cause damage to the product or the camera mount.
Do not clean the product with paint thinner, benzene, or other volatile solvents.
Controller and AC adapter are not water proof.
If the products are dropped in water, contact the service center immediately.
Design by Seculine
Made in Korea

Please ensure all parts are present after opening the box.
Package Contents
Ballast (LM1600)
LED Panel(PN-FL800) x2
Controller Plate
Panel Support(PS800) x2
Y Cable Ball Head Soft Box Set

Name of each part
Power Switch
LED Panel port
DMX on/o button
DMX display
DMX channel setting
Display
Color temperature dimmer
Brightness dimmer
Brightness lock lamp
Color temp. lock lamp
Rod Supprot
Soft Box Body Corner Supprot
Soft Diuser
DC input
Accessory mount
AC input
Latch
Handle
DMX out
DMX in
V battery latch
V battery mount

Specfications
Optional Accessories
Dimension
Weight
Dimming
CCT
Display
Cable Length
Control Lock
Consumption
DMX
Input
Ballast (LM1600)
355 x 170 x 90 mm
2kg
0~100%
2700ºK ~ 6500ºK
Mono LCD
2m (can be extended)
Yes
240W
512 Channel
AC 100~240V 50/60Hz
DC 24V(240W)
2 V-mount battery(FL1600VK only)
Dimension
Weight
Dimming
Photometric
Color Temperature
LED Cells
CRI
Consumption
LED Panel (PN-FL800)
460 x 240 mm
300 g
0~100%
3400 lux
2700ºK ~ 6500ºK
800
94 or above
120W
Extension Cable (3m)
ECF603 ECF605
Extension Cable (5m)

Setting FL1600
Attach Panel Support to each other
Locate and insert the joining point of Panel Support.Then
tighten the two screws to secure it.
1
2
1
1
3
2
5
4

Attach LED Panel
Pull out the LED panel port to the back of the Panel
Support. Attach the LED panel to the Panel Support
by velcro.
2
Install Ballast
Insert the Ballast into the plate by pushing it into the
hole. Then Connect the Y-cable to the panel port on
the ballast.
4
Install Ballast plate
Install Ballast plate using 8 screws on Panel Support.
Y cable terminals and two LED panels.
3

Install Ball head
Align the ball head with the hole on the ballast. Then, x
it by turning it. When detaching, press the detach button
and remove it in reverse order of mounting.
5
2
1
Install the soft box
Fix Coner Support to the corner of Panel Support
with 2 screws. Then insert Rod support into Coner
support.
6
Soft Diuser
Soft box body
Insert Rod support into the corner of
Soft box body. Attach Soft diuser after
installation of Soft box body is nished.
Rod
Soft Box Body
Coner

Input the Power
1. Connect the power source using the AC cable supplied with the package.
2.Turn on the power button to check the LCD.
3. DC power is available also. (24C / 240W)
1. AC adapter
1. Insert theV battery to the battery port.
2.V battery is available only two of all,
3.Turn on the power button to check the LCD.
4.When removing the battery, press the detach latch and remove the
battery in reverse order of mounting.

Opterating the ballast
Turning the brightness dial to the right increases brightness.
Turn the dial to the left decreases brightness. You can adjust the
Brightness by 0~100% dimming. Display shows up to value.
1. Adjust Brightness
Turn the dial to the right increases Color temperature and left
decreases Color temperature.You can adjust color temperature
from 2700°K to 6500°K. Display shows up to value.
2. Adjust the ColorTemperature
Press the button to lock the color temperature dimmer.
The LED will light up red and the dimmer cannot work.
You can also unlock by pressing it again.
3. Lock the change the value.

Press DMX button 1 second in order to set channel.
DMX LCD will be shown blinking.
Change the channel 000~511 by turning the button.
Press DMX button to select channel.
(1 channel : Adjusting brightness / 2 channels : Adjusting
brightness and color temperature. )
Press DMX button1 second, channel setting is completed.
1.
2.
3.
4.
4. DMX
DMX encorder
LED 1
LED 2
2
3
1
4